Aaeon FWS-7250 User manual

Network Appliance FWS- 7 250

FWS-7250

1U Rackmount

Network Appliance Platform

Internal 2.5” SATA HDD x1

or 3.5” SATA HDD x 1

or 2.5” SATA HDD x 2

CF SATA Socket

4 LAN Ports

2 USB2.0, 1 COM for Console

1 MiniCard Slot

FWS-7250 Manual 2

nd

Ed.

February 14, 2019

Network Appliance FWS- 7250

i

Copyright Notice

This document is copyrighted, 2019. All rights are reserved. The

original manufacturer reserves the right to make improvements to the

products described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated, or

transmitted in any form or by any means without the prior written

permission of the original manufacturer. Information provided in this

manual is intended to be accurate and reliable. However, the original

manufacturer assumes no responsibility for its use, or for any in-

fringements upon the rights of third parties that may result from its

use.

The material in this document is for product information only and is

subject to change without notice. While reasonable efforts have been

made in the preparation of this document to assure its accuracy,

AAEON assumes no liabilities resulting from errors or omissions in

this document, or from the use of the information contained herein.

AAEON reserves the right to make changes in the product design

without notice to its users.

Network Appliance FWS- 7250

ii

Acknowledgments

All other products’ name or trademarks are properties of their

respective owners.

 Intel

®

and Atom™ are trademarks of Intel

®

Corporation.

 AMI is a trademark of American Megatrends Inc.

 CompactFlash™ is a trademark of the Compact Flash

Association.

 Microsoft Windows

®

is a registered trademark of Microsoft Corp.

All other product names or trademarks are properties of their

respective owners.

Network Appliance FWS- 7250

iii

Packing List

Before installation, please make sure that the following

materials have been shipped:

 FWS-7250

 Gift Box (Including Console Cable, Ear Brackets)

If any of these items should be missing or damaged, please

contact your distributor or sales representative immediately.

Note:

VGA Cable is an optional accessory. Please only purchase

cable with the following item number.

 1700160150 VGA Cable (must be used with two

S21D305011 screws)

Network Appliance FWS- 7250

iv

Contents

Chapter 1 General Information

1.1 Introduction ....................................................... 1-2

1.2 Features ............................................................ 1-3

1.3 Specifications .................................................... 1-4

1.4 General System Information .............................. 1-8

Chapter 2 Quick Installation Guide

2.1 Safety Precautions ............................................ 2-2

2.2 Location of Connectors of Main Board ............... 2-3

2.3 Mechanical Drawing of Main Board ................... 2-5

2.4 List of Jumpers .................................................. 2-7

2.5 List of Connectors ............................................. 2-7

2.6 Setting Jumpers ................................................ 2-9

2.7 Auto Power Button (JP1) ................................... 2-10

2.8 CF Power Selection (CN13)............................... 2-10

2.9 CMOS Setting Selection (CN16) ........................ 2-10

2.10 RTC Test Setting Selection (CN17) ................. 2-11

2.11 24-Pin ATX Power Connector (CN1) ................ 2-12

2.12 Power Button (CN2) ........................................ 2-13

2.13 SIM Card Socket (CN4) ................................... 2-13

2.14 Compact Flash Socket (CN5) .......................... 2-14

2.15 LCM Connector (CN6) ..................................... 2-16

2.16 PS2 Keyboard/Mouse Pin Header (CN8) ......... 2-17

Network Appliance FWS- 7250

v

2.17 SATA Port Connector (CN9) ............................ 2-18

2.18 SATA Power Connector (CN10 & CN14) ......... 2-18

2.19 USB2.0 Port 1 Pin Header (CN11) ................... 2-19

2.20 VGA Pin Header (CN12) .................................. 2-20

2.21 SATA Port Connector (CN15) .......................... 2-21

2.22 Mini PCI-E Slot (CN19) .................................... 2-21

2.23 USB2.0 Type-A Connector (CN20) .................. 2-24

2.24 Console Port Connector (CN21) ...................... 2-24

2.25 Giga LAN Port Connector (CN22) .................... 2-25

2.26 Giga LAN Port Connector (CN23) .................... 2-26

2.27 Giga LAN Port Connector (CN24) .................... 2-26

2.28 Giga LAN Port Connector (CN25) .................... 2-27

2.29 COM Port Connector (COM1) .......................... 2-28

2.30 4-pin Fan Connector (CPU_FAN1) .................. 2-30

2.31 Front Panel Connector (FP1) ........................... 2-30

2.32 Front Panel Connector (FP2) ........................... 2-31

2.33 4-pin Fan Connector (SYS_FAN1) ................... 2-31

2.34 Installing the 2.5” Hard Disk Drive .................... 2-32

2.35 Installing the 3.5” Hard Disk Drive .................... 2-36

Chapter 3 AMI BIOS Setup

3.1 System Test and Initialization ............................ 3-2

3.2 AMI BIOS Setup ................................................ 3-3

Chapter 4 Driver Installation

4.1 Installation ......................................................... 4-3

Network Appliance FWS- 7250

vi

Appendix A Programming the Watchdog Timer

A.1 Watchdog Timer Initial Program .................... A-2

Network Appliance FWS- 7250

Chapter 1 General Information 1- 1

General

Information

Chapter

1

Network Appliance FWS- 7250

Chapter 1 General Information 1- 2

1.1 Introduction

FWS-7250 adopts the Intel

®

Quad-Core Celeron™ J1900

Processor. The system memory features two 204-pin Dual channel

DDR3L 1333MHz SODIMM slots up to 8GB. It deploys four

Gigabit Ethernet LAN ports with two pairs LAN bypass function. The

condensed appearance of FWS-7250 features 1U form factor that

fits nicely into a space- limited environment.

This compact FWS-7250 can be equipped with one 3.5”/2.5” SATA

HDD and CF-SATA socket or two 2.5” SATA HDD. In addition, it

offers flexible expansion with network products and features one

Mini-Card slot with SIM socket, two USB2.0 ports and one RS-232

console port on the front panel. The console port deploys console

re-direction that increases the network security via remote control.

Moreover, the front panel supports LCM with keypad control for

easy access and operation. All of these designs provide for a more

user-friendly solution.

Network Appliance FWS- 7250

Chapter 1 General Information 1- 3

1.2 Features

 1U Rackmount 4 LAN ports Network Appliance

 Intel® Atom™ E3845, up to 1.91 GHz or Celeron® J1900 up

to 2.42 GHz

 Two 204-pin Dual Channel DDR3L 1333MHz SODIMM Up to

8GB

 Intel® I210AT, 10/100/1000Base-TX Ethernet Port x 4

 Internal 2.5” SATA HDD x 1 or (2.5” SATA HDD x 2 /3.5”

SATA HDD x 1 optional), CompactFlash™ Socket x 1

 RJ-45 Console x 1, USB 2.0 x 2

 100W ATX PSU

Network Appliance FWS- 7250

Chapter 1 General Information 1- 4

1.3 Specifications

Platform

Form Factor

1U Rackmount Network Platform

Processor

Intel® Atom™ E3845, up to 1.91 GHz/

Celeron® J1900 up to 2.42 GHz

Chipset

Integrated

System Memory

DDR3(L) 1333 SODIMM, u

p to 8GB, 204

Pin DIMM x 2

Network

Ethernet

Intel® i210AT, Gigabit Ethernet x 4

Bypass

2

NIM Slot

—

Display

Graphic Controller

Intel® Integrated

Connector

VGA cable (Optional)

Storage

HDDs

Internal 2.5” SATA HDD x 1 or (2.5” SATA

HDD x 2 /3.5” SATA HDD x 1 optional)

CF/CFast/mSATA

CF socket x 1

Network Appliance FWS- 7250

Chapter 1 General Information 1- 5

Expansion/Internal Interface

PCIe slot

—

Mini-Card slot

1

IPMI

—

Keyboard and

Mouse

Pin-header

Universal Serial Bus

USB 2.0 x1 Box Header (2.0mm)

(optional)

Miscellaneous

RTC

Internal RTC

Watchdog Timer

1~255 steps by software programmable

Software Button

GPIO Programmable push button x 1

TPM

—

GPIO

—

FAN

2

MTBF (Hours)

110,000

Color

Black

Network Appliance FWS- 7250

Chapter 1 General Information 1- 6

Environmental Parameters and Dimension

Power Requirement

100W ATX PSU

Operation Temp.

32°F ~ 104°F (0°C ~ 40°C)

Storage Temp.

-4°F ~ 140°F (-20°C ~ 60°C)

Operating Humidity

10% ~ 80%

Storage Humidity

10% ~ 80% @ 40°C, non-condensing

Vibration

0.5 Grms/ 5 ~ 500Hz/ operation (3.5”

H.D.D)

1.5 Grms/ 5 ~ 500Hz/ no operation

Shock

10G peak acceleration (11 m sec.

duration), operation

20G peak acceleration (11 m sec.

duration), non-operation

Chassis Dimension

(W x D x H)

16.93” x 11.02” x 1.73” (430mm x 280mm

x 44mm)

Network Appliance FWS- 7250

Chapter 1 General Information 1- 7

I/O Interfaces

Front Panel

- Power LED x 1

- Status LED x 1

- HDD Active LED x 1

- LAN ports Link/Active LED x 4

- Bypass LED (Default 2 LEDs)

- USB 2.0 Ports x 2

- RJ-45 Console x 1

- Parallel LCM display and 4 keypad x 1

- Software Programmable Switch x 1

Rear Panel

- AC Power Input x 1

- Power Switch x 1

- VGA port (Optional)

Network Appliance FWS- 7250

Chapter 1 General Information 1- 8

1.4 General System Information

Network Appliance FWS- 7 250

Chapter 2 Quick Installation Guide 2-1

Quick

Installation

Guide

Chapter

2

Network Appliance FWS- 7 250

Chapter 2 Quick Installation Guide 2-2

2.1 Safety Precautions

The installation is intended for technically qualified personnel who

have experience installing and configuring system boards.

The equipment can be installed in a restricted access location (RAL)

only.

A restricted access location is a site location for equipment where

the following criteria apply:

01. Access can only be gained by service persons or by users who

have been trained on the restrictions and the precautions for this

specific site.

02. Access is by means of at least one of the following, special tool,

lock and key, or other means of security, and is controlled by the

authority responsible for the location.

Safety Precautions:

Always completely disconnect the power cord

from your board whenever you are working on

it. Do not make connections while the power is

on, because a sudden rush of power can

damage sensitive electronic components.

Always ground yourself to remove any static

charge before touching the board. Modern

electronic devices are very sensitive to static

electric charges. Use a grounding wrist strap at

all times. Place all electronic components on a

static-dissipative surface or in a static-shielded

bag when they are not in the chassis

Network Appliance FWS- 7 250

Chapter 2 Quick Installation Guide 2-3

2.2 Location of Connectors of Main Board

Network Appliance FWS- 7 250

Chapter 2 Quick Installation Guide 2-4

Network Appliance FWS- 7 250

Chapter 2 Quick Installation Guide 2-5

2.3 Mechanical Drawing of Main Board

Page is loading ...

Aaeon FWS-7250 User manual

Aaeon FWS-7250 User manual

Related papers

Other documents