Intermetro LTTA18C Datasheet

Type
Datasheet
InterMetro Industries Corporation
North Washington Street
Wilkes-Barre, PA 18705
www.metro.com
Top-Track
High-Density Storage Systems
Item # ______________________________________________
Job ________________________________________________
11.12
®
®
TOP-TRACK
HIGH-DENSITY
STORAGE SYSTEMS
for Super Erecta
®
and
Super Adjustable Super Erecta
®
Systems
Reduce Inventory Costs
Increase Revenues
Maximize Storage Capacity
Increase Productivity
Simplify Operations
Cleaner Between Cleanings
Maximizes Storage Capacity: Top-Track can increase
the storage capacity of a given area by 30% to 40%.
Mobile units are used between stationary units. Only
one aisle, which can be opened between any two units
as needed, is required. The Top-Track Storage system
utilizes far less aisle space and maximizes the usable
storage area.
Cost-Saving Performance: This efficient utilization
of space addresses the storage needs of new or
growing operations. In a new facility, less square footage
would have to be dedicated to storage. In growing
operations, Top-Track can eliminate the need to expand
the facility to handle increasing storage requirements,
greatly reducing the costs associated with a growing
business’s needs.
Improved Organization and Inventory Control:
Top-Track allows better organization of stored goods
and permits improved inventory control with one-stop
delivery and pick-up.
Increased Productivity: With reduced square footage
dedicated to storage, Top-Track maximizes the amount
of productive “front of the house” space available,
increasing daily revenues.
Accessible: The overhead track system guides the
mobile units and opens an access aisle between any
two units, whenever it is needed. The open access
promotes cleanliness and easy access for walking or
for utility carts, simplifying the material handling task.
Super Erecta
/
Super Erecta Super Adjustable: Super
Erecta and Super Adjustable shelves are available in a
variety of widths and lengths. Each system features
ease of assembly, promotes air circulation, promotes
light penetration and shelf level adjustability. Super
Adjustable features shelf corners with a quick release
lever. Shelves can be rapidly adjusted, without the use
of tools, to meet changing storage needs. Shelves are
available in Brite,
chrome, Metroseal 3 with *Microban
®
built-in product protection and stainless steel.
*MICROBAN
®
and the MICROBAN
®
symbol are registered trademarks of the Microban Products Company, Huntersville, NC.
®
®
TOP-TRACK
HIGH-DENSITY STORAGE SYSTEMS
OVERHEAD VIEWFRONT VIEW
System Components
A = Stationary End Units
B = Stationary Intermediate Unit (Optional)
C = Track Set
D = Mobile Units
E = Open Aisle
Dimensions
Cat. No. Cat. No. Cat. No. Shelf Width
Stationary End Unit Kits Chrome-Plated Metroseal 3 Stainless Steel (in.) (mm)
Includes hardware necessary for connecting stationary end units to TTE18C TTE18K3 TTE18S 18 457
track. ONE KIT IS REQUIRED PER SINGLE SYSTEM. SHELVES SOLD TTE21C TTE21K3 TTE21S 21 530
SEPARATELY. 86" (2185mm) posts included. Just add shelves. TTE24C TTE24K3 TTE24S 24 610
Cat. No. Cat. No. Cat. No. Shelf Width
Stationary Intermediate Unit Kits Chrome-Plated Metroseal 3 Stainless Steel (in.) (mm)
Includes hardware necessary for connecting intermediate unit to track TTA18C TTA18K3 TTA18S 18 457
on both sides. ONE KIT IS REQUIRED PER SINGLE SYSTEM. SHELVES TTA21C TTA21K3 TTA21S 21 530
SOLD SEPARATELY. 86" (2185mm) posts included. Just add shelves. TTA24C TTA24K3 TTA24S 24 610
6' 7' 8' 9' 10' 11' 12' 13'
Track Sets (1830mm) (2135mm) (2440mm) (2745mm) (3050mm) (3355mm) (3660mm) (3965mm)
Includes necessary sections TTS6NA TTS7NA TTS8NA TTS9NA TTS10NA TTS11NA TTS12NA TTS13NA
of track for assembling
14' 15' 16' 17' 18' 19' 20' 21'
track runs of 6'–21'
(4270mm) (4575mm) (4880mm) (5185mm) (5490mm) (5795mm) (6100mm) (6405mm)
(1830mm–6405mm).
TTS14NA TTS15NA TTS16NA TTS17NA TTS18NA TTS19NA TTS20NA TTS21NA
Cat. No. Cat. No. Cat. No. Shelf Width
Mobile Unit Kits Chrome-Plated Metroseal 3 Stainless Steel (in.) (mm)
One kit required per mobile unit. Kit includes posts, casters/caster TTM18C TTM18K3 TTM18S 18 457
channels, donut bumpers, roller bearing assemblies, hardware, and TTM21C TTM21K3 TTM21S 21 530
split sleeves. SHELVES SOLD SEPARATELY. Just add shelves. TTM24C TTM24K3 TTM24S 24 610
NOTES:
1. The stationary end and intermediate units must have a minimum of four shelves.
2. The standard Top-Track
system requires the use of 86" (2185mm) posts (i.e., 86PK3 or 86PS) on the stationary end and intermediate units. Shelves for the stationary end and
intermediate units are sold separately.
3. The mobile unit kits includes special 74" (1880mm) posts with casters. Shelves for mobile units are sold separately.
4. Recommended maximum load rating for a mobile unit is 900 lbs. (400kg). Floor should be level, smooth, and free from large cracks and raised obstacles.
5. Under normal conditions, an aisle width of 30"-36" (762-914mm) is recommended. The storage of very large objects within the system, however, may require an aisle width larger
than 36" (914mm).
6. A stationary intermediate unit is required when track length exceeds 21 feet (6401mm). A stationary intermediate unit may be used at the discretion of the user when track lengths are less
than 21 feet (6401mm).
BA D D D E
C
AD D D E
C
C
E
D D DA B
C
E
D D D A
®
TOP-TRACK
HIGH-DENSITY STORAGE SYSTEMS
OVERHEAD VIEWFRONT VIEW
System Components
Dimensions
Cat. No. Shelf Width
Stationary End Unit Kits Chrome-Plated (in.) (mm)
Includes hardware necessary for connecting stationary end units in Double Deep systems and LTTE18C 18 457
connecting to an overhead track set. ONE KIT IS REQUIRED FOR ENTIRE DOUBLE DEEP LTTE21C 21 530
CONFIGURATION. SHELVES SOLD SEPARATELY. 86" (2185mm) posts included. Just add shelves. LTTE24C 24 610
Cat. No. Shelf Width
Stationary Intermediate Unit Kits Chrome-Plated (in.) (mm)
Includes hardware necessary for connecting intermediate stationary end units in Double Deep systems and LTTA18C 18 457
connecting to an overhead track set on each side. ONE KIT IS REQUIRED FOR ENTIRE DOUBLE DEEP LTTA21C 21 530
CONFIGURATION. SHELVES SOLD SEPARATELY. 86" (2185mm) posts included. Just add shelves. LTTA24C 24 610
Close-up showing shelving units connected end-to-end
in two Top-Track
systems
6' 7' 8' 9' 10' 11' 12' 13'
Track Sets (1830mm) (2135mm) (2440mm) (2745mm) (3050mm) (3355mm) (3660mm) (3965mm)
TTS6NA TTS7NA TTS8NA TTS9NA TTS10NA TTS11NA TTS12NA TTS13NA
14' 15' 16' 17' 18' 19' 20' 21'
(4270mm) (4575mm) (4880mm) (5185mm) (5490mm) (5795mm) (6100mm) (6405mm)
TTS14NA TTS15NA TTS16NA TTS17NA TTS18NA TTS19NA TTS20NA TTS21NA
Includes necessary sections of
track for assembling track runs of 6'
to 21' (763-6405mm). ONLY ONE
TRACK SET IS REQUIRED
BETWEEN STATIONARY UNITS.
Cat. No. Shelf Width
Mobile Unit Kits Chrome-Plated (in.) (mm)
Includes the necessary posts, casters, caster channels, donut bumpers, roller bearing LTTM18C 18 457
assemblies, and tie-together hardware to connect two mobile units together (i.e., one in LTTM21C 21 530
each system). SHELVES SOLD SEPARATELY. Just add shelves. LTTM24C 24 610
NOTES:
1. The stationary end and intermediate units must have a minimum of four shelves. For all Super Adjustable applications, the top and bottom shelves are to be non quick adjust
Super Erecta shelves.
2. The standard Double Deep Top-Track
system requires the use of 86" (2185mm) posts (i.e., 86P) on the stationary end and intermediate units. Shelves for the stationary end and
intermediate units are sold separately.
3. The mobile unit kit includes special 74" (1880mm) posts with casters. Shelves for mobile units are sold separately. For all Super Adjustable applications, the top and bottom shelves are to
be non “quick adjust” Super Erecta shelves.
4. Under normal conditions, an aisle width of 30"-36" (762mm-914mm) is recommended. The storage of very large objects within the system, however, may require an aisle width larger
than 36" (914mm).
5. Two intermediate shelving units connected end-to-end are required when the track length exceeds 21 feet (6401mm). Stationary intermediate shelving units may be used at the discretion of
the user when track lengths are less than 21 feet (6401mm).
6. The maximum Double Deep system configuration is 10'7" (3202mm) (e.g., two systems, each having 60" (1525mm) for long shelves plus 6" (152mm) for Top-Track components.)
7. Ease of rollability for the mobile unit is an important consideration in evaluating Top-Track as a possible storage alternative. The floor should be level, smooth, and free from large cracks and
raised obstacles. Two mobile shelving units connected end-to-end and loaded with between 800 to 1,200 lbs. (365-550kg) will require a human effort range (in lbs. of human force) of
between 18-24 lbs. (8-11kg) to move the unit from a complete stop. An average person will perceive this as acceptable effort levels.
8. Mobile units should have the top shelf positioned as close as possible to the track.
A = Stationary End Units
B = Stationary
Intermediate Unit
(Optional)
C = Track Set
D = Mobile Units
E = Open Aisle
C
E
D D DA B
C
E
D D D A
BA D D D E AD D D E
C
C
BA D D D E
C
AD D D E
C
Top-Track
High-Density Storage Systems
®
®
L02-039
Printed in U.S.A. 8
/
03
Information and specifications are subject to change
without notice. Please confirm at time of order.
Copyright © 2003 InterMetro Industries Corp.
®
InterMetro Industries Corporation
North Washington Street, Wilkes-Barre, PA 18705
Phone: 570-825-2741 • Fax: 570-825-2852
For Product Information Call: 1-800-433-2232
All Metro Catalog Sheets are available on our Web Site:
www.metro.com
11.12
TOP-TRACK
HIGH-DENSITY
STORAGE SYSTEMS
Specifications
Track: Aluminum extrusion 6063-T6.
Joining Channel: 16 gauge galvanized steel.
Roller Assembly: Zinc-plated steel hardware with
nylon roller.
Casters:
For applications where Brite
or chrome finishes are
acceptable: 5" (127mm) wheel with offset rigid horn,
ball bearings in axle, nickel-plated, pre-lubricated.
For applications where Metroseal 3 and stainless steel
are acceptable: 5" (127mm) wheel with offset stainless
steel rigid horn, stainless steel ball bearings in axle, pre-
lubricated.
Workable Configurations of Mobile Units Base on Various Track Lengths and Desired Aisle Sizes
Nominal Aisle Size = 30" (760mm) Nominal Aisle Size = 33" (838mm) Nominal Aisle Size = 36" (914mm)
No. Mobile Units (Note 1) Actual No. Mobile Units (Note 1) Actual No. Mobile Units (Note 1) Actual
Length 18" 21" 24" Aisle Size 18" 21" 24" Aisle Size 18" 21" 24" Aisle Size
of Track (457mm) (530mm) (610mm) (in.) (mm) (457mm) (530mm) (610mm) (in.) (mm) (457mm) (530mm) (610mm) (in.) (mm)
62 31
1
/2 800 2 31
1
/2 800
7231
1
/2 800 2 31
1
/2 800 2 37
1
/2 952
81 2 29
1
/4 749 2 1 32
1
/4 819 3 35
1
/4 895
9329
1
/4 749 1 2 32
1
/4 819 1 2 35
1
/4 895
10 2 1 1 30 762 3 1 33 838 3 1 36 914
11 1 3 30 762 2 2 33 838 3 1 36 914
12 1 4 30
3
/4 781 2 3 34
3
/4 857 3 2 36
1
/4 933
13 2 3 30
3
/4 781 3 2 34
3
/4 857 4 1 36
1
/4 933
14 4 3 31
1
/2 800 2 4 32
1
/4 819 6 1 35
1
/4 895
15 4 3 29
1
/4 749 5 2 32
1
/4 819 6 1 35
1
/4 895
16 8 30 762 1 6 32
1
/4 819 2 5 35
1
/4 895
17 4 4 30 762 5 3 33 838 7 1 36 914
18 8 30 762 1 7 33 838 2 6 36 914
19 2 6 30 762 2 1 5 33 838 3 5 36 914
20 8 30 762 1 7 33 838 2 6 36 914
21 5 5 34
1
/2 876 6 4 37
1
/2 952
NOTE 1: Actual overall width of nominal 18" (457mm), 21" (530mm), and 24" (610mm) wide mobile units is 20
1
/4" (667mm). The number of mobile units here applies to individual
units in a single system, and sets of units (two mobile units tied back-to-back) in a double deep system.
NOTE 2: In confined spaces, usable space for the Top-Track installation should be determined by deducting 4" (102mm) from the overall measured space. This allows for
variables such as building tolerances.
Example
Selection Criteria: Actual track length required: 17'3" (5228mm). Aisle width must be in 30"-36" (762-914mm) range.
Nominal 30" (762mm) Aisle Nominal 33" (838mm) Aisle
18" 21" 24" 18" 21" 24"
Selection of Mobile Units (457mm) (530mm) (610mm) (457mm) (530mm) (610mm)
17' (5185mm) 4 4 5 3
Other selections would produce a movable aisle outside the 30"-36" (762-914mm) range.
Beyond the standard configurations mentioned above, custom Top-Track capabilities include:
Attaching one end of the track to a wall in a single or double deep installation.
Tying together a cluster of two mobile units (i.e., side-to-side) in a single system, or four mobile units in a double deep system.
A taller installation up to a maximum height of 8' (2438mm) (i.e., 86" (2185mm) high posts in the stationary end units).
Metroseal 3 and stainless steel Top-Track components for the double deep application.
Track assemblies 6.5', 7.5' (1956, 2261mm) in length.
Contact factory for details.
Job ________________________________________________
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Intermetro LTTA18C Datasheet

Type
Datasheet

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI