RAB Lighting WPLED26Y/E USA Operating instructions

Brand: RAB Lighting

Model: WPLED26Y/E USA

Type: Operating instructions

This manual is also suitable for

WPLED26 EMERGENCY INSTALLATION SHEET

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper

grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT

AND THE HAZARDS INVOLVED.

WARNING: Make certain power is OFF and batteries are DISCONNECTED before installing or maintaining xture.

No user serviceable parts inside.

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call

the Marketing Department at 888-RAB-1000, or email: marketing@rabweb.com

MOUNTING

CAUTION: Suitable for Wet Locations as Downlight

and Wall Mount only.

1. Loosen and remove (4) Screws and separate Back

Box from Emergency Housing. Use provided tether.

2. Drill necessary holes on Back Box. Measurements

of drill positions are shown below.

3. Match the hole pattern and place the Gasket on the

Back Box.

4. Secure the Back Box on the surface with hardware

appropriate for the mounting surface.

5. Wire the xture to the incoming supply wires

according to NEC and local codes. Use UL listed

wire connectors.

6. For WPLED26/E, each battery unit has one

connector. For WPLED26/EC, each battery unit has

two connectors as shown below. For details refer to

the appropriate Wiring Diagram section and supplied

Instruction Sheet.

7. Connect the battery connectors. DO NOT connect

the Batteries before wiring the xture to the supply.

8. Secure Housing to Back Box. Check Housing

Gasket seal all around.

9. Apply sealant to all unused conduit entry points.

To ensure weatherproof seal, apply weatherproof

silicone sealant around the edge where the xture

meets the wall.

Housing

Screws

Bracket Screw

Two connectors for

WPLED26/EC

Back Box Housing

Gasket

WPLED26/E

Battery

Connector

Gasket

Screws

Bracket

Emergency

Batteries

WPLED26 EMERGENCY INSTALLATION SHEET

CLEANING & MAINTENANCE

CAUTION: Be sure xture temperature is cool

enough to touch. Do not clean or maintain while

xture is energized.

1. Clean glass lens & xture with non-abrasive glass

cleaning solution.

2. Do not open xture to clean the LED. Do not touch

the LED.

US: Pat. D634,873; CN: ZL 201030129137.X; MX: 32491;

TW: D139540; CA: D RAB Lighting Inc. Patent Pending.

Note: These instructions do not cover all details or variations

in equipment nor do they provide for every possible situation

during installation, operation or maintenance.

WPLED26 (2X13)

EMERGENCY 120V OR

277V

WIRING DIAGRAM

2.22.12

LED 26W EMERGENCY

120V OR 277V WIRING DLC

AC DRIVER

COM

GROUND

BODINE

BSL722 LED

EMERGENCY

DRIVER

BATTERY 1

LEAVE OPEN

DO NOT CONNECT

DURING

MANUFACTURING

CUSTOMER SHOULD

CONNECT ONLY AFTER

FINISHING WIRING TO AC

POWER. BATTERY COULD

HAVE CHARGE & SHOCK

RED-WHITE STRIPE

RED

FUSE

HOLDER

CHARGING

INDICATOR LIGHT /

TEST SWITCH

BLUE

WHITE

YELLOW

YELLOW - BLACK STRIPE

WPLED26

SWITCHED HOT

CHARGING

INDICATOR/

TEST

SWITCH

BLACK

WHITE

WHITE/BLACK

VIOLET

BROWN

RED-WHITE STRIPE

BLUE

BLACK

BLACKGREY

GREY

WHITE

WHITE - RED STRIPE

WHITE

BLACK

WHITE

BLACK

UNSWITCHED HOT

RAB LABEL - ADD

LABEL PROVIDED

BATTERY 2

EMERGENCY

HOUSING

RED

BLACK

WPLED26/E WIRING DIAGRAM (Refer to next page for WPLED26/EC wiring diagram)

2.940

[74,68]

7.500

[190,5]

.600

[15,24]

3.750

[95,25]

DRILL TEMPLATE

7.5”

3.75”

0.6”

2.94”

WPLED26 EMERGENCY INSTALLATION SHEET

WPLED26 (2X13)

EMERGENCY 120V OR

277V

WIRING DIAGRAM

4.18.12

LED 26W EMERGY COLD

120V OR 277V WIRING DLC

AC DRIVER

COM

GROUND

BODINE

BSL722 LED

EMERGENCY

DRIVER

BATTERY 1

LEAVE OPEN

DO NOT CONNECT

DURING

MANUFACTURING

CUSTOMER SHOULD

CONNECT ONLY AFTER

FINISHING WIRING TO AC

POWER. BATTERY COULD

HAVE CHARGE & SHOCK

RED-WHITE STRIPE

RED

FUSE

HOLDER

CHARGING

INDICATOR LIGHT /

TEST SWITCH

BLUE

WHITE

YELLOW

YELLOW - BLACK STRIPE

WPLED26

SWITCHED HOT

CHARGING

INDICATOR/

TEST

SWITCH

BLACK

WHITE

WHITE/BLACK

VIOLET

BROWN

RED-WHITE STRIPE

BLUE

BLACK

GREY

WHITE

YELLOW/RED

WHITE - RED STRIPE

WHITE

BLACK

WHITE

BLACK

UNSWITCHED HOT

RAB LABEL - ADD

LABEL PROVIDED

BATTERY 2

EMERGENCY

HOUSING

RED

BLUE/ORANGE

RED

BLACK

WHITE

RED

YELLOW/RED

RED

WHITE

YELLOW/RED

RED

BLUE

RED

WHITE

RED

YELLOW/RED

RED

WHITE

BLUE/ORANGE

BAT 1

BAT 2

BAT 1

BAT 2

WPLED26/EC WIRING DIAGRAM (Refer to previous page for WPLED26/E wiring diagram)

WPLED26/EMG-IN-0414

RAB Lighting WPLED26Y/E USA Operating instructions

Brand: RAB Lighting

Model: WPLED26Y/E USA

Type: Operating instructions

This manual is also suitable for

Download PDF

report

RAB Lighting WPLED26Y/E USA Operating instructions

This manual is also suitable for

RAB Lighting WPLED26Y/E USA Operating instructions

Related papers

Other documents