One Stop Gardens Item 93358 Owner's manual

Page 2 For technical questions, please call 1-800-444-3353. Item 93358

Table of Contents

Safety ......................................................... 3

Specifications ............................................. 4

Assembly .................................................... 5

Maintenance .............................................. 29

Warranty .................................................... 32

Parts Lists .................................................. 30

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

Page 3For technical questions, please call 1-800-444-3353.Item 93358

IMPORTANT SAFETY INFORMATION

The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions

and situations that may occur. The operator must understand that common sense and caution are factors,

which cannot be built into this product, but must be supplied by the operator.

Assembly / Installation Precautions

1. Assemble only according to these instructions.

Improper assembly can create hazards.

2. Wear ANSI-approved safety goggles and

heavy-duty work gloves during assembly.

3. This unit contains pieces with sharp edges.

The machined edges of the aluminum parts

and the ends of the panel clips may be sharp.

Handle all parts carefully.

4. Keep assembly area clean and well lit.

5. Keep bystanders out of the area during assembly.

6. Do not assemble when tired or when under the

influence of alcohol, drugs or medication.

7. Product capabilities apply to properly and

completely assembled product only.

8. Locate the Greenhouse on a flat, level, surface.

A concrete foundation is recommended

for a high-quality installation.

9. WARNING: The brass bushings inside the

Rollers of this product contain lead, a chemical

known to the State of California to cause

birth defects (or other reproductive harm).

(California Health & Safety Code § 25249.5, et seq.)

Use / Service Precautions

1. This product is not a toy. Do not allow

children to play in or climb on this product.

Although this greenhouse does include some caps,

there are still some exposed sharp edges.

In addition, protective covers may fall off in time.

Children must be supervised if

allowed near the greenhouse.

2. SNOW/DEBRIS ACCUMULATION HAZARD.

The heavy weight of accumulated snow or other

debris can cause parts of this greenhouse to buckle

suddenly. Do not allow debris to accumulate on

top of the greenhouse. If snowfall is expected,

place additional supports (not provided) underneath

the Crown. NEVER enter a greenhouse

with accumulated debris on top.

3. Use as intended only.

4. Inspect periodically; replace damaged parts

immediately and do not enter greenhouse

if parts are loose or damaged.

5. For your safety, service and maintenance should

be performed regularly by a qualified technician.

SAVE THESE INSTRUCTIONS.

Page 4 For technical questions, please call 1-800-444-3353. Item 93358

Specifications

Overall Dimensions 120

1

/

2

″ W x 144

1

/

2

″ L x 123″ H

Window Dimensions 23

1

/

4

″ W x 31

1

/

4

″ L

Door Dimensions 75

1

/

2

″ H x 35

1

/

2

″ W x 1

1

/

4

″ Thick

Materials

Aluminum Frame

Transparent Polycarbonate Sheets

Aluminum Thickness 0.038″

Polycarbonate Sheet Thickness 0.165″

Page 5For technical questions, please call 1-800-444-3353.Item 93358

Assembly

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document

including all text under subheadings therein before set up or use of this product.

IMPORTANT–READ THE FOLLOWING CAREFULLY BEFORE PROCEEDING

• Thefirststepinassemblyistoassembleaproperbase.Thegreenhousemustbeproperly

supported to help prevent property damage and injury in the event of strong winds or

inclement weather. Wind and ground conditions may vary from site to site, and may affect

the practicality and effectiveness of anchoring methods substantially. If you have any doubt

regarding the stability of the base/foundation you are to use, consult a professional.

• Itisalwaysyourresponsibilitytoensurethatthegreenhouseisproperlyanchored.

Harbor Freight Tools cannot be held responsible for personal injury, damage to the greenhouse,

or other property damage that occurs as a result of improperly anchoring the greenhouse.

• Becertaintocheckwithlocalauthoritiestoobtainallrequiredbuildingpermits

and to familiarize yourself with any building codes that may apply.

• Decideonalocationforthegreenhouse.Thelocationshouldoptimallybea

level, well-lit area that is sheltered from the wind. The door of the greenhouse

should not open towards the prevailing wind, if possible.

IMPORTANT ASSEMBLY TIPS

• AssembleBoltswiththeirheadsfacingtheoutsideofthegreenhouse,unlessstatedotherwise.

Tighten Nuts (67) only about 1/4 turn past finger-tight; be careful not to overtighten.

• Layoutallpartsbynumberpriortoassembly.

• Atleasttwoassistantswillbenecessaryduringassembly.

• Assembleonaclear,calmday.WindwilldamagetheGreenhouseandmakeassemblydifficult.

Page 6 For technical questions, please call 1-800-444-3353. Item 93358

Phase 1: Base Assembly

All parts in this phase

are fastened using

32 Base Bolts (68)

and 32 Base Nuts (69).

Page 7For technical questions, please call 1-800-444-3353.Item 93358

Base Assembly Instructions

1. Excavate an area for the base of the greenhouse.

The area must be 10′ 2″ wide by 12′ 2″ long by

5″ deep. The floor of the hole must be level

and square. The diagonal dimensions, from

corner to corner, should each be 15′ 5″.

2. Assemble the Base outside the hole as shown

below. Note that the angled edges of the

Base Plates (43, 44) need to face the corners of

the base. Use Base Bolts (68), Base Nuts (69), and

Connectors (45, 46) to secure the pieces together.

3. With assistance, lower the Base into the hole.

The diagonal dimensions,

from outside corner to outside corner,

must be equal for the base to be square.

4. Fill the hole around the outside of the base with soil.

5. This base will need to be filled with about

40 cubic feet of gravel or another appropriate

fill material (not provided). The gravel should

reach up to about 1″ below the lip of the base.

Page 8 For technical questions, please call 1-800-444-3353. Item 93358

Phase 2: Floor Plate Installation

All parts in this phase

are fastened using

16 Normal Bolts (65)

and 16 Nuts (67).

44

43

44

4

5

1a

2a

(Front)

(Right)

(Rear)

(Left)

3

6

3

47

a

b

c

Floor

Plate

Base

Plate

gravel

Hold-down Connector (47)

attachment

a. Slide Connector (47) under lip.

b. Insert Regular Bolt (65).

c. Fasten with Nut (67)

Grey parts are in place before this phase.

Page 9For technical questions, please call 1-800-444-3353.Item 93358

Floor Plate Installation Instructions

1.

gravel

ground

Base Plate

(43, 44)

Rear/Side

Floor Plates

(3 – 6)

Front Floor

Plate (1a, 2a)

outside

greenhouse

Cross Section

When placing the Floor Plates (1a–6) on top of

the Base Plates (43, 44), align them as illustrated

above. The lip should extend slightly over the

edge of the Base Plate and the raised flange with

bolt holes should face inside the greenhouse.

2. Place the Front-Left Floor Plate (1a)

on top of the Base Plate (44). Lay the

Front-Right Floor Plate (2a) on top of it and line

up the 2 holes where the Plates overlap.

3. Fasten the Front Floor Plates (1a, 2a) together,

and secure to the Base Plate (44) using a

Hold-down Connector (47) over one of the

Bolts (65), see inset on facing page.

4. Place the Side Floor Plates (4) on the

Side Base Plates (43) on the front-right

and rear left corners as illustrated. Lay the

Upper Side Floor Plates (3) on top so that the

three holes line up where the Plates overlap.

5. Fasten the Side Floor Plates (3, 4) together,

and secure to the Base Plates (43) using

3 Hold-down Connectors (47) on each side

of the greenhouse in the places illustrated;

see illustration and inset on facing page.

6. Lay the Rear-right Floor Plate (6) on top of the

Rear-left Floor Plate (5) so that the 2 holes

line up where the Plates overlap. Fasten the

Rear Floor Plates (5, 6) together through those holes.

7. Place the assembled Rear Floor Plates (5, 6)

on top of the Base Plates (44).

8. Secure the Rear Floor Plates (5, 6)

to the Base Plates (44) using

2 Hold-down Connectors (47) in the locations

shown; see illustration and inset on facing page.

Page 10 For technical questions, please call 1-800-444-3353. Item 93358

47

67

65

7

Phase 3: Corner Post Installation

Parts in this phase

are fastened using

10 Normal Bolts (65),

14 Brace Bolts (66),

2 Double Brace Bolts (78),

and 26 Nuts (67).

(Front)

(Right)

(Rear)

(Left)

5

6

4

3

4

1a

2a

7

49

7

31

79

80

a

b

d

c

Floor

Plate

Base

Plate

gravel

Hold-down Connector (47)

attachment with Strut (79, 80)

a. Slide Connector (47) under lip.

b. Insert Brace Bolt (66).

c. Slide Strut (79, 80) over Bolt.

d. Fasten with Nut (67)

Grey parts are in place before this phase.

Page 11For technical questions, please call 1-800-444-3353.Item 93358

Corner Post Installation Instructions

1. There are 4 Corner Posts (7) to be attached

to the Floor Plates (1–6). The end with 2

holes should be at the bottom, as shown in

the illustration in the center of this page.

2. Attach one Corner Post (7) on the outside of

the right rear Floor Plates (3, 6) using 2 Normal

Bolts (65), 2 Hold-down Connectors (47),

and 2 Nuts (67), see inset - facing page.

3.

49

66

65

78

67

7

31

79

80

(Rear)

(Right)

(View from inside greenhouse.)

Fasten a Corner Bracket (49) to the top

of the Corner Post (7) over the Rear Floor

Plate (6) using one Normal Bolt (65) for

now. Install it angled up towards the center

of the greenhouse, as shown above.

4. Install a Double Brace Bolt (78) through the bottom

hole of the Corner Bracket (78). Place a Rear

Brace (31) over it with the arrow pointing towards

the Bolt. Also place Front/Rear Diagonal Strut (79)

over the Bolt, and thread on Nut (67) hand-tight.

5. Fasten a Side Diagonal Strut (80) to

the free top hole on the Corner Post (7)

using Brace Bolt (66) and Nut (67).

6. Fasten Struts (79, 80) to Floor Plates using

Brace Bolts (66), Hold-down Connectors (47),

and Nuts (67), see inset on facing page.

Allow Rear Braces (31) to hang free.

7. Repeat steps 2 through 6 for the left rear

Corner Post (7) on the left side. Keep

in mind that the connections will be

reversed compared to the right side.

8. Attach one Corner Post (7) on the outside

of the front left Floor Plates (1a, 3)

using 2 Normal Bolts (65), 2 Hold-down

Connectors (47), and 2 Nuts (67).

9.

49

66

67

7

79

80

(Front)

(Left)

(View from inside greenhouse.)

Insert a Brace Bolt (66) through the second

hole from the top of the Corner Post (7) over the

Front Floor Plate (1a). Place the bottom hole

of the Corner Bracket (49) over the Bolt with it

angled up towards the center of the greenhouse,

as shown above. Secure it using a Nut (67).

10. Fasten a Side Diagonal Strut (80) to the top

hole on the Corner Post (7) over the Side Floor

Plate using a Brace Bolt (66) and Nut (67).

11. Secure the Struts (79, 80) to the Floor Plates

using Brace Bolts (66), Hold-down Connectors

(47), and Nuts (67), see inset on facing page.

12. Repeat steps 8 through 11 for the right

front Corner Post (7) on the right side.

Keep in mind that the connections will be

reversed compared to the left side.

BOTTOM

TOP

Corner Post (7)

Page 12 For technical questions, please call 1-800-444-3353. Item 93358

1. Insert Normal Bolts (65) through all holes in the

front of the Front Ceiling Plates (24, 25), as

shown. Thread a Nut (67) onto each

Bolt, but leave all Nuts loose for now.

2. Slide the slot on the Right

Door Rail (27) over

the heads of the 2

Bolts on the

Front-

right

Ceiling Plate (25) until the right end

is flush, as shown.

The illustration in the center of this

page shows how to slide the Rail

over the Bolt heads.

Tighten the Nuts on those 2 Bolts.

3. Slide the Bolt heads on the Front-left

Ceiling Plate (24) into the slot of the

Right Door Rail (27) from the left edge until

it rests against the Front-right Ceiling

Plate (25).

Tighten the 2 right-most

Nuts on the Ceiling Plate.

4. Slide the slot on the Left Door Rail (26) over the

heads of the remaining three Bolts in the Front-

left Ceiling Plate (24) until it presses against the

Right Door Rail (27).

Tighten the remaining Nuts.

Phase 4a: Ceiling Plate Assembly, Front

26, 27

24, 25

65

Parts in this phase

are fastened using

7 Normal Bolts (65)

and 7 Nuts (67).

Step 3

25

27

24

Tighten these two

Nuts after sliding

Step 4

27

26

25

24

Step 2

25

27

Step 1

24

25

65

Page 13For technical questions, please call 1-800-444-3353.Item 93358

Phase 4b: Ceiling Plate Assembly, Side

1. Insert a Plain Side Ceiling Plate (13) in the brackets

on the end of a Side Ceiling Plate with Brackets (12).

2. Secure in place with 6 Normal Bolts (65)

and 6 Nuts (67). The heads of the Bolts

should all face the gutter side of the Ceiling

Plates, as shown in the inset above.

3. Repeat the two previous steps for the

remaining Plain Side Ceiling Plate (13) and

Side Ceiling Plate with Brackets (12).

4. Attach an End Cap (72) to the top outer corner

of each Corner Post (7) at this point.

Parts in this phase

are fastened using

a total of

12 Normal Bolts (65)

and 12 Nuts (67).

13

12

65

67

13

12

67

65

67

65

13

12

13

12

Page 14 For technical questions, please call 1-800-444-3353. Item 93358

Phase 5: Ceiling Plate Installation

Parts in this phase are fastened using

2 Normal Bolts (65),

8 Brace Bolts (66),

and 10 Nuts (67).

Additional Bolts and Nuts are already

in place before this phase.

(Front)

(Right)

(Rear)

(Left)

7

80

7

13

12

13

12

31

80

24, 25

48

Grey parts are in place before this phase.

Means that the nearby Bolt

will be removed and then re-

attached at the same location.

Page 15For technical questions, please call 1-800-444-3353.Item 93358

Ceiling Plate Installation Instructions

1. Insert one Normal Bolt (65) through the Corner

Bracket (49) and the upper hole in the Corner Post

(7) at both front corners of the greenhouse, from

the inside out, as shown above. This is for the later

attachment of the Front Ceiling Plate (24-27).

2.

(View from inside greenhouse.)

49

67

7

(Front)

(Left)

80

79

12

A

To attach one end of a Side Ceiling Plate (12, 13):

a. Remove the Nut (67) where the Side Diagonal

Strut (80) connects to the Corner Post (7) in

one corner, marked A in the illustration above.

b. Temporarily disconnect that

Side Diagonal Strut (80) from the

Brace Bolt (66), but leave the Bolt in place.

c. Orient the gutter opening up as shown above.

d. Place the Side Ceiling Plate (12, 13) then

the Side Diagonal Strut (80) on the end of

the Bolt, and secure with a Nut (65).

3. Secure the other end of that

Side Ceiling Plate (12, 13) similarly.

4. Attach the Front Ceiling Plate (24, 25)

to the 2 Normal Bolts (65) put in

place in step 1 on the outside of the

greenhouse, note orientation at right.

5. Attach the remaining Side Ceiling Plate (12, 13)

along the other side according to steps 2 & 3,

with the gutter opening up.

6.

31

48

(View from

inside

greenhouse.)

67

66

Bolt 2 Post Connectors (48) to a Rear Brace (31)

using Brace Bolts (66) through their bottom holes,

from the outside in. Place Post Connectors

on the outside of the greenhouse with the

flat side against the Brace, as shown above.

Only finger tighten for now.

7. Swing the Rear Braces (31) together and bolt the

second Brace to the second from bottom holes on

the Post Connectors (48), using Brace Bolts (66)

from the outside in. Only finger tighten for now.

Note: The Rear Braces (31) will be under tension.

8. If you cannot attach the second

Post Connector (48), or if they are not parallel:

Make sure that the arrows on both

of the Rear Braces (31) are pointing

towards the Corner Posts (7).

Page 16 For technical questions, please call 1-800-444-3353. Item 93358

Phase 6: Post Installation

Parts in this phase are fastened using

8 Normal Bolts (65),

2 Brace Bolts (66),

4 Double Brace Bolts (78),

and 14 Nuts (67).

Additional Bolts and Nuts are already

in place before this phase.

(Front)

(Right)

(Rear)

(Left)

80

14

66(x4)

14

66(x4)

14

66(x4)

14

66,78,66

31

80

13

12

13

12

14

66(x4)

14

66(x4)

14

66(x4)

14

66,78,66

14

66,78,66

14

66(x4)

17

66(x2)

16

66(x2)

14

66(x4)

14

66,78,66

81

44 Brace Bolts (66)

are inserted into Posts

during this phase for

use in phase 7.

3

4

5

6

48

Grey parts are in place before this phase.

Means that the nearby Bolt will be removed

and then re-attached at the same location.

Means that the bolt underneath will be

loosened, a Post will slide over the bolt

head, and then it will be re-tightened.

Page 17For technical questions, please call 1-800-444-3353.Item 93358

Post Installation Instructions

Note: All Posts (14, 16, 17) in this

phase require extra Bolts to be

inserted into their slot before

assembly. The small numbers

under the main part number on the

facing page are the type and

number of hardware.

See the examples below:

14

66,78,66

17

66(x2)

Post Part Number

Inserted Bolt

Part Numbers

Meaning: Insert 2 Brace

Bolts (66) into the

Rear Right Post (17)

before attaching it.

Meaning: Insert a Brace

Bolt (66), then a Double

Brace Bolt (78), then

another Brace Bolt (66)

into this Side Post (14)

before attaching it.

1. Loosen a Bolt on one of the Side Floor

Plates (3,4) in an attachment location

as shown. Slide the slot in a Side Post

(14) over the head of that Bolt.

2. Insert the required Bolts (See note

above and illustration on facing page)

into the slot in the Side Post.

3. Attach the top of the Side Post (14) to

the Ceiling Plate (12, 13), using a Normal

Bolt (65) in the slot or using the Bolt

already in place for the center Post.

4. Repeat above steps for all 10 Side Posts (14)

on the left and right sides of the greenhouse.

5. Slide a white Bushing (81) over all 4

inserted Double Brace Bolts (78). Place

the center hole of each Side Diagonal

Strut (80) over the end of each Double

Brace Bolt and secure with a Nut (67).

6. Loosen a Bolt on the Rear Floor Plate

(5, 6) in a location that a Side Post (14)

attaches, and slide a Side Post over

the head of that Bolt. Insert 4 Brace

Bolts (66) into the slot of that Post.

7.

(View from outside greenhouse.)

66

48

31

14

Side Post (14) must extend

no farther than halfway up

the Post Connector (48).

Remove the 2 Brace Bolts (66) connecting

the Post Connector (48) near that Side

Post. Slide the heads of those Bolts into the

Side Post and insert them through the Post

Connector. Align the top of the Post with the

center of the Connector as shown above, and

press it in place. Reattach the Rear Braces

(31) to the Brace Bolts (66) and secure them.

8. Repeat steps 6 & 7 for another Side

Post (14) and Post Connector (48).

9. Loosen the Bolts (66) where the Rear

Diagonal Struts (79) connect to the Rear Floor

Plate (5, 6). Slide the slot in the Rear-Left

Post (16) over the head of the left Bolt and

the Rear-Right Post (17) over the right Bolt.

10. The slanted ends of the Posts must be

on top and slant towards the center of

the greenhouse. Retighten the Bolts.

11. Slide 2 Brace Bolts (66) into the slot

of each Rear Post (16, 17).

12. Slide one more Brace Bolt (66) into the top

of each Rear Post. Attach the Rear Posts

to the Rear Braces (31) using those Bolts.

13. The frame should now rest square. Measure

diagonally from corner to corner at the top. If

the measurements are not equal, adjust the

frame as needed until square. Some Nuts

(67) may need to be loosened to adjust the

frame. Tighten all Nuts after adjustment.

Page 18 For technical questions, please call 1-800-444-3353. Item 93358

Phase 7: Brace Installation

Parts in this phase are fastened using

2 Normal Bolts (65),

20 Brace Bolts (66),

and 66 Nuts (67).

Additional Bolts and Nuts are already

in place before this phase.

Grey parts are in place before this phase.

Means that the nearby Bolt will be removed

and then re-attached at the same location.

(Front)

(Right)

(Rear)

(Left)

7

80

14

17

14

16

80

28

80

29

80

31

30

14

7

24, 25

7

32

Page 19For technical questions, please call 1-800-444-3353.Item 93358

Brace Installation Instructions

Note:

Brace

(30 - 32)

Strut (79, 80)

Post (14, 16, 17)

Corner Post (7)

All Braces are installed inside the Posts,

but outside the Struts. See diagram above,

shown from inside the greenhouse facing out.

1.

to (left)

Corner

Post (7)

(Outside greenhouse)

(Doorway)

(Inside greenhouse)

to (right)

Corner

Post (7)

29 28

(View from above.)

Using a Normal Bolt (65) at top and the Brace

Bolt (66) already in place at the bottom for each,

attach the Left and Right Doorway Posts (28, 29)

to the outside of the Front Floor Plates (1a, 2a)

and to the inside of the Front Ceiling Plates (24,

25). Install the Posts with the cut-outs at top and

oriented as shown in the illustration above.

2. Using Brace Bolts (66), connect the Front

Braces (32) between the Corner Posts (7) and

the Doorway Posts (28, 29). Install Braces

inside Posts but outside Struts, as shown

in the diagram at the top of this page.

Note: Install the Braces on the walls so that they are

level. If the frame is level and all Braces are level,

the Braces should not interfere with one another.

3. Connect the 4 remaining Rear Braces (31) onto

the rear wall as shown on the facing page, with

the arrows pointing towards the Corner Posts (7).

Secure in place using Brace Bolts (66) at the Corner

Post and the inserted Brace Bolts in the remaining

holes. Install Braces inside Posts but outside Struts,

as shown in the diagram at the top of this page.

4. Connect 4 Side Braces (30) onto each side wall

as shown on the facing page, with the arrows

pointing towards the Corner Posts (7). Secure in

place using Brace Bolts (66) at the Corner Post and

the inserted Brace Bolts in the remaining holes.

Install Braces inside Posts but outside Struts, as

shown in the diagram at the top of this page.

5. Place the Gutter End Caps (73) onto the ends of the

Side Ceiling Plates (12, 13) oriented with a gap in

the bottom to allow water to drain out of the gutters.

Page 20 For technical questions, please call 1-800-444-3353. Item 93358

(Front)

(Right)

(Rear)

(Left)

17

14

16

28

29

24, 25

8

18

10

11

9

22

20

21

23

8

19

9

Phase 8: Gable and Crown Installation

Parts in this phase are fastened using

36 Normal Bolts (65)

and 36 Nuts (67).

Additional Bolts and Nuts are already

in place before this phase.

Grey parts are in place before this phase.

Means that the bolt underneath will be

loosened, a Post will slide over the bolt

head, and then it will be re-tightened.

12

13

48

Page is loading ...

One Stop Gardens Item 93358 Owner's manual

This manual is also suitable for

One Stop Gardens Item 93358 Owner's manual

Related papers

Other documents