Posiflex PD-7600 (EN) User manual

Brand: Posiflex

Model: PD-7600 (EN)

Type: User manual

Part 1

FCC Notes:

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions manual, may cause interference to radio

communications. It has been tested and found to comply with limits for a Class A

digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to

provide reasonable protection against interference when operated in a commercial

environment. Operation of this equipment in a residential area is likely to cause

interference in which case the user at his own expense will be required to take whatever

measures to correct the interference.

Warranty Limits:

Warranty terminates automatically when any person other than the authorized

technicians opens the machine. The user should consult his/her dealer for the problem

happened. Warranty voids if the user does not follow the instructions in application of

this merchandise. The manufacturer is by no means responsible for any damage or

hazard caused by improper application.

About This Manual:

Posiflex has made every effort for the accuracy of the content in this manual. However,

Posiflex will assume no liability for any technical inaccuracies or editorial or other

errors or omissions contained herein, nor for direct, indirect, incidental, consequential

or otherwise damages, including without limitation loss of data or profits, resulting

from the furnishing, performance, or use of this material.

This information is provided “as is” and Posiflex Technology, Inc. expressly disclaims

any warranties, expressed, implied or statutory, including without limitation implied

warranties of merchantability or fitness for particular purpose, good title and against

infringement.

The information in this manual contains only essential hardware concerns for general

user and is subject to change without notice. Posiflex reserves the right to alter product

designs, layouts or drivers without notification. The system integrator shall provide

applicative notices and arrangement for special options utilizing this product. The user

may find the most up to date information of the hardware from web sites:

http://www.posiflex.com or http://www.posiflex.com.tw

All data should be backed-up prior to the installation of any drive unit or storage

peripheral. Posiflex will not be responsible for any loss of data resulting from the use,

disuse or misuse of this or any other Posiflex product.

All rights are strictly reserved. No part of this documentation may be reproduced,

stored in a retrieval system, or transmitted in any form or by any means, electronic,

mechanical, photocopying, or otherwise, without prior express written consent from

Posiflex Inc. the publisher of this documentation.

All brand and product names and trademarks are the property of their respective holders.

PD - 7600 Series Customer Display

User’s Manual

Rev. C0

P/N:

1949

09000

Part 2

BRIEF INTRODUCTION

THE PRODUCT

The PD-76X0 is a stand alone pole mount customer display designed for

discrete POS applications, The PD-76X4 is a Rear-base pole mount customer

display option designed for XP series POS terminals and Gen.6 base stand for

KS series & Gen.4.5 for LM series. The PD-7600 series utilizes a graphical

LCD module with backlight. It supports 4 rows display of 15 Chinese or 30

Arabic characters each in format of 16 by 16 dots or 8 by 16 dots respectively.

FEATURES

• Graphic STN LCD (liquid crystal display) in blue background with

white backlight

• Stand alone Pole Display for POS application (PD-76X0)

• Four-line display with 30 Arabic letters or 15 Chinese characters

per line

• 240 by 64 dots for graphic display

• Adequately sized characters for easy viewing (8.47 mm by 4.24

mm per digit)

• Long life and trouble free operation

• Display contrast adjust buttons on front surface

• 15 , 30 and 45 adjustable viewing angles

• Display frame can rotate horizontally 270° freely

• Supports ESC/POS commands

• Simple installation

• Serial (RS232) interface for PD-76X0; RJ45 interface for PD-76X4

• Case color choices: ivory, black

MODELS, LANGUAGES & CODE TABLES

Stand Alone Pole Mount model:

• PD-7610: Simplified Chinese, GB-2312

• PD-7620: Traditional Chinese, BIG-5

• PD-7630: Arabic, Windows code page 01256 (with Arabic

numerals addressed in <80> ~ <89> of code page 1)

• PD-7640: Hindi.

Rear-Base Pole Mount model:

• PD-7614: Simplified Chinese, GB-2312

• PD-7624: Traditional Chinese, BIG-5

• PD-7634: Arabic, Windows code page 01256 (with Arabic

numerals addressed in <80> ~ <89> of code page 1)

Part 3

INSTALLATION GUIDES

PACKAGE CONTENTS

The pole display with base or pole display with fix bracket

The User’s manual

RS-232 signal cable (for PD-76X0)

Power adaptor per country type ordered (for PD-76X0)

Self-tapping screws for PD-76x4 use in Gen.4.5 base stand.

Bing Head Screw for Gen 6 of KS series and XP series.

PHYSICAL INSTALLATION

Stand Alone Pole Mount model:

Find a flat surface to site the base of the display for application operation. Find

in the bottom of the base the connectors as in the drawing below:

The RJ45 type modular connector is for internal use and is already occupied.

The RS232 input port is a DB9 female connector. Connect the attached RS-

232 signal cable to this port and one of the COM port in the host system. Set

the RS-232 communication protocol for this port to 9600 bps, no parity, 8 bits,

1 stop bit with hardware handshaking. Connect the power adaptor to the

rightmost power connector. Turn on the switch in the front side of the base.

Rear-Base Pole Mount model:

The PD-76X4 can be attached to either rear corner

of bottom plate of XP series and Gen.6, Gen.4.5

base stands of KS series. Firstly, it takes XP series

for example. Please aim the hole to the arrowed

screw which shows in the right picture. Use the 3

attached Bing head screws to fix the metal base plate

of the PD to the bottom of XP series base as circled

in the picture. Arrange the interface cable to go through under bottom to XP

series system connector area. Adjust the direction of the display head for best

viewing effect in application. For integrated to the Gen.4.5 base stand, please

aim to the holes which marked “DT” and use the self-tapping screws to fix on

the Gen.4.5 base.

To Display head

24 VDC

RS232 input

12 VAC input

Part 4

Stand Alone Model:

This instruction is for stand alone model only. Please

unpack the inner box of pole display and it easy to find

the base, display unit with tube and adaptor separately.

Please remove the PE foam and bring out the components

carefully.

Firstly, place the display head and tube on a flat surface

and find the cable which in the end of tube. Let this cable

pass through the short tube which on the base stand and it

shows in the picture at right.

Next, please assemble the display head with tube to the

base stand which shows in the right picture. Please pay

more attention during the process since there is a hole and

a compression lock which are in the two side of tube and

marked arrow signs. Aim these two arrow signs nearby

compression lock to the holes and push the tube to the end.

After hear the “click” sound, the assembly is complete.

Once combine the display head with tube and base stand,

please place the pole display as a horizontal position

which can easily to check the bottom plate.

Please plug the cable to the connector which showing “To

Display” and route the cable as arrowed in the right

picture.

DRIVER INSTALLATION

For application software to use the RS232 interfaced PD-7600 series, there is

no direct need for any driver.

APPLICATION GUIDES

CONTRAST ADJUST

Use the 2 buttons on right side of the display head front

surface to increase / decrease the contrast of LCD

Part 5

COMMAND LIST

Command Hex Code Function

ESC DC1 <1B><11>

US MD1 <1F><01>

Specify Overwrite Mode

ESC DC2 <1B><12>

US MD2 <1F><02>

Specify Vertical Scroll Mode

CLR <0C> Clear Display Screen

ESC @ <1B><40> Initialize Display

ESC _ n <1B><5F><n> Set Cursor ON/OFF (n=0,1)

US r n <1F><72><n> Select/Cancel Reverse Character (n=0,1)

ESC = n <1B><3D><n> Data Display Select (n=1,2)

US T h m <1F><54><h><m> Set Time (0≤h≤0x17; 0≤m≤0x3B)

US U <1F><55> Display Time Continuously

ESC G d

~ d

1920

<1B><47><d

>~<d

1920

Bit Image Display

ESC t n <1B><74><n> Select Code Page (n=0,1)

HT <09>

ESC [C <1B><5B><43>

Move Cursor Right

BS <08>

ESC [ D <1B><5B><44>

Move Cursor Left

US LF <1F><0A>

ESC [ A <1B><5B><41>

Move Cursor Up

LF <0A>

ESC [ B <1B><5B><42>

Move Cursor Down

HOM <0B>

ESC [ H <1B><5B><48>

Move Cursor to Home Position

US CR <1F><0D>

ESC [ R <1B><5B><52>

Move Cursor to Right-Most

CR <0D>

ESC [ L <1B><5B><4C>

Move Cursor to Left-Most

US B <1F><42>

ESC [ K <1B><5B><4B>

Move Cursor to Bottom

US S x y <1F><24><x><y>

ESC I x y <1B><6C><x><y>

Move Cursor to Specified Position

(0≤x≤0x1D; 0≤y≤3)

Part 6

SPECIFICATION

OPTICAL

Number of digits 30 digits/row, 4 rows

Dot matrix 8 x 16 dots

Digit height 8.47 mm

Digit width 4.24 mm

Display color White

Background color Blue

MECHANICAL

Total Height 431 mm (PD-76X0)

200 mm (PD-76X4)

Total Width 221 mm.4

Total Depth 110 mm.4base39.06

Display Window Width 130 mm

Display Window Height 37 mm

Case color Black or Ivory (PD-76X0)

Black (PD-76X4)

ELECTRICAL

Power from adaptor: 12 V AC 1.5A

RS-232 communication protocol: 9600 bps, none parity, 8 data

bits, 1 stop bit

ENVIRONMENTAL

Operating temperature 0° to + 50°C

Storage temperature -10° to + 60°C

Operating humidity 20% to 85%, non-condensing

Storage humidity 5% to 90%, non-condensing

WARNING: If the user opens the pole display housing to make any

modification, all the product warranty will be voided.

NOTE: Please refer to Posiflex Product Information DVD or visit

our web http://www/posiflex.com.tw for further information when

needed.

T31454

Posiflex PD-7600 (EN) User manual

Posiflex PD-7600 (EN) User manual

Posiflex PD-7600 (EN) User manual

Related papers

Other documents