Extron MVX 1212 VGA A User manual

MVX 1212 VGA A
Extron
Brand
Extron
Model
MVX 1212 VGA A
Category
Video switches
Type
User manual
Extron USA - West
Headquarters
+800.63 3.9876
Inside USA / Canada Only
+1.714.491.150 0
+1.714.491.1517 FAX
Extron USA - East
+800.63 3.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.39 87.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.638 3.44 00
+65.638 3.46 64 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FA X
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2009 Extron Electronics. All rights reserved.
Setup Guide
68-521-54 Rev. A
11 09
MVX VGA A
Computer Video (VGA) and Audio Matrix Switchers
MVX Matrix Switcher Part Numbers
These items are included in each order for a MVX A matrix
switcher:
Matrix switcher part numbers Replacement part
number
MVX 128 VGA A 60-799-01
MVX 1212 VGA A 60-858-01
MVX 168 VGA A 60-838-01
MVX 1616 VGA A 60-839-01
Precautions
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no user-
serviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparation-
maintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Safety Instructions • English
Consignes de Sécurité • Français
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio •
Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Instrucciones de seguridad • Español
Extron Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron USA
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Europe, Africa, and the Middle East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
Asia:
Extron Asia
135 Joo Seng Road #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Japan:
Extron Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
China:
Extron China
686 Ronghua Road, Songjiang
District
Shanghai 201611
China
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or non-
Extron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
安全须知 • 中文
这个符号提示用户该设备用户手册中
有重要的操作和维护说明。
这个符号警告用户该设备机壳内有暴
露的危险电压，有触电危险。
注意
阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理
解 所 有 安 全 和 使 用 说 明 。
保存说明书 • 用户应保存安全说明书以备将来使
用。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备，以避免危险。
警告
电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备
必 须 使 用 有 地 线 的 供 电 系 统 供 电 。 第 三 条 线
（ 地 线 ） 是 安 全 设 施 ， 不 能 不 用 或 跳 过 。
拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后
或桌面电源的电源线，或任何接到市电系统的电源线。
电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。
维护 • 所有维修必须由认证的维修人员进行。 设备内部
没有用户可以更换的零件。为避免出现触电危险不要自
己试图打开设备盖子维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用
与厂家推荐的相同或相近型号的电池。 按照生产厂的
建议处理废弃电池。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
N
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
MVX VGA A Matrix Switchers • Precautions and Listings
Refer also to the MVX VGA A User’s Manual at www.extron.com.
i
MVX VGA A Matrix Switchers • Table of Contents
Table of Contents
Refer also to the MVX VGA A User’s Manual at www.extron.com.
Chapter One • Introduction .................................................... 1-1
About this Manual .................................................................... 1-2
About the Matrix Switchers ................................................... 1-2
Chapter Two • Installation ...................................................... 2-1
Rear Panel Installation Features ........................................... 2-2
Front Panel Configuration Port ............................................. 2-4
Chapter Three • Front Panel Operation.......................... 3-1
Creating a Tie .............................................................................. 3-3
Saving or Recalling a Preset ................................................... 3-4
Setting the Front Panel Locks (Executive Modes) ........... 3-5
Selecting Lock mode 2 or toggling between
mode 2 and mode 0 ............................................................... 3-5
Selecting Lock mode 2 or toggling between
mode 2 and mode 1 ............................................................... 3-6
Viewing and Adjusting the Input Audio Level and
Output Volume ........................................................................... 3-6
Viewing Ties (and Muting Outputs) .................................... 3-7
Chapter Four • Remote Control ........................................... 4-1
Selected SIS Commands........................................................... 4-2
Installing and Starting the Control Program .................... 4-7
Installing the program ........................................................... 4-7
Starting the program ............................................................. 4-8
Button-Label Generator Program ......................................... 4-9
All trademarks mentioned in this manual are the properties of their respective owners.
MVX VGA A Matrix Switchers • Precautions and Listings
Refer also to the MVX VGA A User’s Manual at www.extron.com.
ii
MVX VGA A Matrix Switchers • Table of Contents
Table of Contents, cont’d
MVX VGA A Matrix Switchers
Refer also to the MVX VGA A User’s Manual at www.extron.com.
1
Chapter One
Introduction
About this Manual
About the Matrix Switchers
MVX VGA A Matrix Switchers • Introduction
Introduction
MVX VGA A Matrix Switchers
1-2
Refer also to the MVX VGA A User’s Manual at www.extron.com.
N
For more information on any subject in this guide, refer to
the MVX VGA A User’s Manual, available on the Extron
DVD or at www.extron.com.
About this Manual
This setup guide allows you to easily and quickly set up and
configure your matrix switcher. This guide also shows you how to:
• Perform basic operations using the front panel controls
• Perform basic operations using selected
Simple Instruction Set (SIS
™
) commands
• Load and start up the Windows
®
-based Matrix Switchers
Control Program
About the Matrix Switchers
The Extron VGA matrix switchers covered in this manual
distribute any input to any combination of outputs. The
switchers can route multiple input/output combinations
simultaneously. The switchers are available in four matrix sizes
(the number of inputs and outputs):
• MVX 128 VGA A (12 inputs by 8 outputs)
• MVX 168 VGA A (16 inputs by 8 outputs)
• MVX 1212 VGA A (12 inputs by 12 outputs)
• MVX 1616 VGA A (16 inputs by 16 outputs)
INPUTS
OUTPUTS
RESET
RS232/RS422
REMOTE
LISTED
1T23
I.T.E.
C
U S
1 2 3 4 5 6 7 8
9 10 11
12
1 2 3 4 5
6 7 8
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
INPUTS
OUTPUTS
VID
50/60 Hz
1
2
3
4
Y
/VID
B-Y
H/
HV
R
/R-Y
V
G
/Y
B
/B-Y
RS-232
LAN
RESET
ACT
LINK
RGB/R-Y,Y,B-Y
YC
SDI
R-Y
/C
RGB/R-Y,Y,B-Y/YC/VID
100-240V .3A
I
N
P
U
T
O
U
T
P
U
T
I
N
P
U
T
O
U
T
P
U
T
Control System
Plasma
Plasma
LCD
Projector
VSC 500
SCAN CONVERTER
SIZE
MIN/MAX
NEXTMENU
FREEZE
RESET
IR
CENTER/PAN/SIZE
Sound System
Extron
VSC 500
Video Scan Converter
VCR
PC
Laptop
Laptop
Audio In
Extron
DVS 304
Digital Video Scaler
DVD
Extron
MVX Series
VGA and Audio
Matrix Switcher
Audio In
Audio Out
2
Chapter Two
Installation
Rear Panel Installation Features
Front Panel Configuration Port
MVX VGA A Matrix Switchers • Installation
Installation
MVX VGA A Matrix Switchers • Installation
2-2
Refer also to the MVX VGA A User’s Manual at www.extron.com.
2-3
Refer also to the MVX VGA A User’s Manual at www.extron.com.
Rear Panel Installation Features
RS-232/RS422
REMOTE
RESET
COMPUTER IN
1
2
5
6
9
10
13
14
3
4
7
8
11
12
15
16
COMPUTER OUT
1
2
5
6
9
10
13
14
3
4
7
8
11
12
15
16
1.2A MAX.
100-240V 50/60 Hz
O
U
T
P
U
T
S
I
N
P
U
T
S
L
15
RL
13
RL
11
RL
9
RL
7
RL
5
RL
3
RL
1
R
L
16
RL
14
RL
12
RL
10
RL
8
RL
6
RL
4
RL
2
R
L
15
RL
13
RL
11
RL
9
RL
7
RL
5
RL
3
RL
1
R
L
16
RL
14
RL
12
RL
10
RL
8
RL
6
RL
4
RL
2
R
1 2 3 4 5 6 7 8
1 2 3 4 5
50
75
OUTPUT
SYNC IMPEDANCE
6 7 8
A n a he im , C A
US
LIS TED
1T23
I.T.E.
®
COMPUTER IN COMPUTER OUT
OUTPUT
MVX 1616 VGA A
7 6
3
1 2
54
COMPUTER IN COMPUTER OUT
RS232/RS422
REMOTE
LIS TED
1T2 3
I.T.E .
1 2 3 4 5 6 7 8
9 10 11 12
1 2 3 4 5 6 7 8
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
INPUTS
OUTPUTS
RESET
COMPUTER IN
COMPUTER OUT
MVX 128 VGA A
7 6
1 2
54
C
Turn off power to the input and output devices, and
disconnect their power cords.
N
The MVX matrix switchers can also switch component
video, S-video, or composite video with the appropriate
adapters.
a
Video inputs — Connect RGB video sources, as appropriate to
your switcher's video format and matrix size.
b
Video outputs — Connect RGB video displays, as appropriate
to your switcher's video format and matrix size.
N
Most laptop or notebook computers have an external
video port that may require special commands to output
the video to that connector. Also, a laptop’s screen shuts
off once the external video port is activated. See the
computer’s user’s guide for details, or contact Extron for a
list of common laptop keyboard commands.
N
The MVX VGA 128 A does not have the Sync Impedance
switches described below.
c
Sync Impedence switches (168, 1212, and 1616 matrix sizes) —
The Sync Impedance switches compensate the output 1
through 8 impendance for different cable types and lengths.
Each switch provides the option of selecting either 50 ohms or
75 ohms. The 50 ohms position is required only when a sync
problem is encountered. The normal position is 75 ohms.
N
An input producing an out-of-sync display — a display
that is rolling vertically and/or tearing horizontally —
could indicate an impedance problem.
d
Audio inputs — Connect audio sources to the 5-pole captive
screw connectors.
Unbalanced Stereo Input
Balanced Stereo Input
Ring
Sleeve (s)
Tip
Sleeve
Tip
Sleeve
Tip
Tip
Ring
Do not tin the wires!
L R
e
Audio outputs — Connect audio devices to the 5-pole captive
screw connectors.
CAUTION
For unbalanced stereo audio, connect the sleeve(s) to the ground
contact. DO NOT connect the sleeve(s) to the negative (-) contacts.
Unbalanced Stereo Output
Balanced Stereo Output
L R
Ring
Tip
Sleeve(s)
Tip
Ring
Sleeve(s)
Tip
Tip
NO GROUND HERE.
NO GROUND HERE.
Do not tin the wires!
f
Remote port — If desired, connect a control or computer to the
rear panel Remote RS-232/RS-422 port.
N
Remote port defaults: RS-232, 9600 baud, no parity, 8-bit,
1 stop bit, no flow control.
RS-232 Function Pin Function
1
2
3
4
5
6
7
8
9
—
TX
RX
—
Gnd
—
—
—
—
Not used
Transmit
Receive
Not used
Ground
Not used
Not used
Not used
Not used
—
TX–
RX–
—
Gnd
—
RX+
TX+
—
Not used
Transmit (–)
Receive (–)
Not used
Ground
Not used
Receive (+)
Transmit (+)
Not used
RS-422
5
1
9
6
g
Power — Plug the switcher into a grounded AC source.
MVX VGA A Matrix Switchers • Installation
Installation, cont’d
2-4
MVX VGA A Matrix Switchers
Refer also to the MVX VGA A User’s Manual at www.extron.com.
Front Panel Configuration Port
ENTER PRESET VIEW ESC RGBHV AUDIO
CONTROL IO
MVX SERIES
VGA MATRIX SWITCHER
WITH
ADSP
TM
CONFIG
8
h
Configuration port — If desired, connect a control or
computer to the front panel Configuration (RS-232) port.
Use an optional 9-pin D to 2.5 mm mini jack TRS RS-232
cable, part #70-335-01.
3
Chapter Three
Front Panel Operation
Creating a Tie
Saving or Recalling a Preset
Setting the Front Panel Locks (Executive Modes)
Viewing and Adjusting the Input Audio Level and Output Volume
Viewing Ties (and Muting Outputs)
MVX VGA A Matrix Switchers • Front Panel Operation
Front Panel Operation
MVX VGA A Matrix Switchers • Front Panel Operation
3-33-2
Refer also to the MVX VGA A User’s Manual at www.extron.com. Refer also to the MVX VGA A User’s Manual at www.extron.com.
N
On some MVX switchers, the video selection button is
labeled “RGBHV” rather than “Video”.
N
The front panel controls and indicators have numerous
functions that are beyond the scope of this setup guide.
Refer to the MVX VGA A Switcher User's Manual,
chapter 3, “Operation” for full details.
a
Input buttons and LEDs — Buttons select inputs for front panel
operations. LEDs identify selected inputs and indicate other
miscellaneous displays.
b
Output buttons and LEDs — Buttons select outputs for front
panel operations. LEDs identify selected outputs and indicate
other miscellaneous displays.
c
Enter button and LED — Button saves changes that you make
on the front panel. LED indicates that a pending change needs
to be saved.
d
Preset button and LED — Button selects modes in which you
can save and recall presets. LED indicates the preset mode.
e
View (
<
) button and LED — Button selects a View mode, in
which you can view the current configuration without making
inadvertent changes and also mute and unmute outputs. Button
also can be used to decrease audio levels. LED identifies view
mode.
f
Esc (
>
) button and LED — Button cancels operations or
selections in progress and resets the front panel button indicators.
Button also can be used to increase audio level. LED flashes
once to indicate that the escape function has been activated.
g
Video button and LED — Button selects video for creation of
ties. LED indicates that video is selected for tie creation.
h
Audio button and LED — Button selects audio for creation
of ties. Button also selects Audio mode, in which you can
adjust audio levels. LED indicates that audio is selected for tie
creation. LED also indicates Audio mode is selected.
Creating a Tie
1. Press and release the Esc button to clear any button
indicators that may be lit.
ESC
Press the Esc button
to clear all selections.
The LED blinks once.
2. Press and release the Video and/or Audio I/O button(s) to
select or deselect video and/or audio as desired.
N
Audio or video can be broken away (tied by itself) by
selecting only the Video button or only the Audio button.
VIDEO AUDIO
I/O
Lit when selected.
Off when deselected.
Lit when selected.
Off when deselected
.
3. Press and release the desired input button.
5
The input LED
lights to indicate
the selection.
4. Press and release the desired output button(s).
3 4 8
ENTER
Output LEDs blink to indicate a potential tie
Enter LED blinks to indicate the
need to confirm the change.
5. Press and release the Enter button. All button indicators
turn off.
MVX SERIES
VGA MATRIX SWITCHER
WITH
ADPS™
ENTER PRESET VIEW ESC VIDEO AUDIO
CONTROL I/O
OUTPUTS
INPUTS
CONFIG
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15
9 10 11 12 13 14 15 16
16
5 6 7 8
1 2
3 4
MVX VGA A Matrix Switchers • Front Panel Operation
Front Panel Operation, cont’d
3-4
MVX VGA A Matrix Switchers • Front Panel Operation
3-5
Refer also to the MVX VGA A User’s Manual at www.extron.com. Refer also to the MVX VGA A User’s Manual at www.extron.com.
Saving or Recalling a Preset
1. Save a preset — Press and hold the Preset button until it
flashes.
Recall a preset — Press and release the Preset button.
PRESET
PRESET
PRESET
PRESET
1 2 3 4 5
Preset LED blinks.
Press and hold.
2 seconds
Save a
preset
Recall a
preset
Preset LED lights.
Press and release.
All input and output buttons with assigned presets light.
The configuration data at assigned preset
locations will be overwritten.
2. Press and release the desired input button.
1
ENTER
The LED blinks to indicate that this preset
is selected.
The Enter LED
blinks to indicate
the need to save or
recall the preset.
3. Press and release the Enter button.
Setting the Front Panel Locks (Executive Modes)
The matrix switcher has three levels of front panel security lock
that limit the operation of the switcher from the front panel. The
three levels are:
• Lock mode 0 — The front panel is completely unlocked.
• Lock mode 1 — All changes are locked from the front
panel (except for setting Lock mode 2). Some functions
can be viewed.
• Lock mode 2 — Basic functions are unlocked. Advanced
features are locked and can be viewed only.
Basic features consist of:
m Making ties
m Saving and recalling presets
m Setting input audio gain and attenuation
m Changing Lock modes
Advanced features consist of:
m Setting video and audio output mutes
m Setting audio output volume
N
The switcher is shipped from the factory in Lock mode 2.
N
For a complete list of advanced features, refer to the
MVX VGA A User’s Manual, available on the Extron
DVD or at www.extron.com.
Selecting Lock mode 2 or toggling between
mode 2 and mode 0
N
If the switcher is in Lock mode 0 or mode 1, this procedure
selects mode 2.
If the switcher is in Lock mode 2, this action selects mode 0
(unlocks the switcher).
Toggle the lock on and off by pressing and holding the
Enter button, the Video button, and the Audio button for
approximately 2 seconds.
VIDEO AUDIO
I/O
ENTER
VIDEO AUDIO
I/O
ENTER
Press and hold the Enter, Video, and Audio
buttons simultaneously to turn on Lock mode 2
or to toggle between mode 2 and mode 0.
2 seconds
The Enter, Video, and
Audio LEDs blink twice to
indicate the mode change.
Release the buttons.
MVX VGA A Matrix Switchers • Front Panel Operation
Front Panel Operation, cont’d
3-6
MVX VGA A Matrix Switchers • Front Panel Operation
3-7
Refer also to the MVX VGA A User’s Manual at www.extron.com. Refer also to the MVX VGA A User’s Manual at www.extron.com.
Selecting Lock mode 2 or toggling between
mode 2 and mode 1
N
If the switcher is in Lock mode 0 or mode 1, this procedure
selects mode 2.
If the switcher is in Lock mode 2, this action selects mode 1.
Toggle the lock on and off by pressing and holding the Video
button and the Audio button for approximately 2 seconds.
VIDEO AUDIO
I/O
VIDEO AUDIO
I/O
Press and hold the Video and Audio buttons simultaneously to
turn on Lock mode 2 or to toggle between mode 2 and mode 1.
2 seconds
The Video and Audio
LEDs blink twice to
indicate the mode change
.
Release the buttons.
Viewing and Adjusting the Input Audio Level
and Output Volume
1. Press and hold the Audio button until it flashes.
AUDIO AUDIO
Audio LED blinks.
Hold
2 seconds
2. Press an input button (for input level) or output button (for
volume). Refer to the MVX VGA A Switcher User's Manual,
chapter 3, “Operation”, to read the displayed value.
OUTPUTS
5
1 2 3 4
Press an input button to adjust gain/attenuation.
- or -
Press an output button to adjust the output volume
.
Output LEDs display
gain/attenuation.
- or -
Input LEDs display
output volume level.
3. Increase/decrease the level
or volume by pressing
the Esc (
>
) and View (
<
)
buttons.
4
. Press and release the Audio
button to exit.
VIEW ESC
button
decreases
the level.
button
increases
the level.
Viewing Ties (and Muting Outputs)
1. Press the View button. Output LEDs light for outputs that
have no ties established.
N
If an output LED blinks, that output is muted.
2. Press an input button. The LEDs for all tied outputs light.
3. Press an output button. The LEDs for the tied input and
all tied outputs light.
4. If you want to toggle a mute on and off, press and hold
the output button for 2 seconds.
5. Press the View button. All input and output LEDs return
to an unlit state.
MVX VGA A Matrix Switchers • Front Panel Operation
Front Panel Operation, cont’d
3-8
MVX VGA A Matrix Switchers
Refer also to the MVX VGA A User’s Manual at www.extron.com.
4
Chapter Four
Remote Control
Selected SIS Commands
Installing and Starting the Control Program
Button Label Generator Program
MVX VGA A Matrix Switchers • Remote Control
Remote Control
MVX VGA A Matrix Switchers • Remote Control
4-34-2
Refer also to the MVX VGA A User’s Manual at www.extron.com. Refer also to the MVX VGA A User’s Manual at www.extron.com.
Selected SIS Commands
The switchers have Simple Instruction Set (SIS
™
) commands
that you can use for operation and configuration. You can run
these commands from a PC connected to either of the switcher’s
serial ports. See f (page 2-3) and h (page 2-4), for connection
information.
Command ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Create ties
N
• Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%4*8$.
•
The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%).
N
When you create a tie where X! = 00, you tie no input to the specified output (X@) (untie X@).
N
The & tie command for RGB and the % tie command for video can be used interchangeably.
N
The & read tie command for RGB and the % read tie command for video can be used interchangeably.
Tie input X!
to output
X@
, video
and audio
X!*X@! OutX@•InX!•All] Tie input X!‘s video and audio to output X@.
Example:
1*3!
Out03
•In01•All]
Tie input 1 video and audio to output 3.
Tie input
X!
to output
X@
, RGBHV
X!*X@& OutX@•InX!•RGB]
Tie RGB only (video breakaway).
Example
(see 3rd Note, above):
10*4&
Out04
•In10•RGB]
Tie input 10 RGB to output 4.
Tie input
X!
to output
X@
, video
X!*X@% OutX@•InX!•Vid]
Tie video only (video breakaway).
Example
(see 3rd Note, above)
7*5%
Out05
•In07•Vid]
Tie input 7 video to output 5.
Tie input
X!
to output
X@
, audio
X!*X@$ OutX@•InX!•Aud]
Tie audio only (audio breakaway).
Example:
12*04$
Out04
•In12•Aud]
Tie input 12 audio to output 4.
Read RGB output tie
X@& X!] RGBHV input X! is tied to output X@.
Read video output tie
X@% X!] Video input X! is tied to output X@.
Read audio output tie
X@$ X!] Audio input X! is tied to output X@.
N
X! = Input number
00 –
(maximum number of inputs for your model)
(00 = untie)
X@ = Output number 01 – (maximum number of outputs for your model)
MVX VGA A Matrix Switchers • Remote Control
4-3
Refer also to the MVX VGA A User’s Manual at www.extron.com.
Command ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Create ties
N
• Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%4*8$.
•
The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%).
N
When you create a tie where X! = 00, you tie no input to the specified output (X@) (untie X@).
N
The & tie command for RGB and the % tie command for video can be used interchangeably.
N
The & read tie command for RGB and the % read tie command for video can be used interchangeably.
Tie input X!
to output
X@
, video
and audio
X!*X@! OutX@•InX!•All] Tie input X!‘s video and audio to output X@.
Example:
1*3!
Out03
•In01•All]
Tie input 1 video and audio to output 3.
Tie input
X!
to output
X@
, RGBHV
X!*X@& OutX@•InX!•RGB]
Tie RGB only (video breakaway).
Example
(see 3rd Note, above):
10*4&
Out04
•In10•RGB]
Tie input 10 RGB to output 4.
Tie input
X!
to output
X@
, video
X!*X@% OutX@•InX!•Vid]
Tie video only (video breakaway).
Example
(see 3rd Note, above)
7*5%
Out05
•In07•Vid]
Tie input 7 video to output 5.
Tie input
X!
to output
X@
, audio
X!*X@$ OutX@•InX!•Aud]
Tie audio only (audio breakaway).
Example:
12*04$
Out04
•In12•Aud]
Tie input 12 audio to output 4.
Read RGB output tie
X@& X!] RGBHV input X! is tied to output X@.
Read video output tie
X@% X!] Video input X! is tied to output X@.
Read audio output tie
X@$ X!] Audio input X! is tied to output X@.
N
X! = Input number
00 –
(maximum number of inputs for your model)
(00 = untie)
X@ = Output number 01 – (maximum number of outputs for your model)
MVX VGA A Matrix Switchers • Remote Control
Remote Control, cont’d
4-4
MVX VGA A Matrix Switchers • Remote Control
4-5
Refer also to the MVX VGA A User’s Manual at www.extron.com. Refer also to the MVX VGA A User’s Manual at www.extron.com.
Command ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Video and audio mute commands
RGB/video mute
X@*1B VmtX@*1] Mute output X@ RGB (video off).
RGB/video unmute
X@*0B VmtX@*0] Unmute output X@ RGB (video on).
Read RGB/video mute
X@B X#]
1 = mute on, 0 = mute off.
Global RGB/video mute 1*B
Vmt1
]
Mute all RGB outputs.
Global RGB/video unmute 0*B
Vmt0
]
Unmute all RGB outputs.
Audio mute
X@*1Z AmtX@*1] Mute output X@ audio (audio off).
Audio unmute
X@*0Z AmtX@*0] Unmute output X@ audio (audio on).
Read audio mute
X@Z X#]
1 = mute on, 0 = mute off.
Global audio mute 1*Z
Amt1
]
Mute all audio outputs.
Global audio unmute 0*Z
Amt0
]
Unmute all audio outputs.
View output mutes
EVM}
X$
1
X$
2
X$
3
... X$
n
]
Each X$ response is the mute status of an output,
starting from output 1.
n = the maximum number of outputs for this model.
Example:
MVX 1616 VGA A
EVM} Mut0220200000000000]
Output 2, 3, and 5 audio is muted. All other
outputs are unmuted.
N
The “Mut” portion of the response appears only when the switcher is in Verbose mode 3. See the Verbose mode command on page 4-6.
N
X@ = Output number 01 – (maximum number of outputs for your model)
X# = Mute 0 = off (unmuted) 1 = on (muted)
X$ = Video/audio mute: 0 = no mutes 2 = audio mute
1 = video mute 3 = video and audio mute
Command ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Audio output volume
Set the audio volume to a specific
value
X@*X%V OutX@•VolX%]
Example:
1*50v
Out01•Vol50
] Set output 1 volume to an X% value of 50, an
attenuation of 14 dB (79% of total volume).
Increment volume
X@+V OutX@•VolX%]
Increase volume by 1 step.
Example:
1+V
Out01•Vol51
]
Decrement volume
X@-V OutX@•VolX%]
Decrease volume by 1 step.
Read output volume
X@V X%]
Save and recall presets
N
If you try to recall a preset that is not saved, the matrix switcher responds with the error code E11.
Save current configuration as a
global preset
X^,
SprX^]
Command character is a comma.
Example:
9
,
Spr09]
Save current ties as preset 9.
Recall a global preset
X^.
RprX^]
Command character is a period.
Example:
5
.
Rpr05]
Recall preset 5, which becomes the current
configuration.
N
X@ = Output number 01 – (maximum number of outputs for your model)
X% = Volume 0 – 64 (1 dB/step except for 0-to-1, which is 22 dB) (default = 64 [0 dB])
X^ = Preset number 01 - 32
MVX VGA A Matrix Switchers • Remote Control
Remote Control, cont’d
4-6
Refer also to the MVX VGA A User’s Manual at www.extron.com.
Command ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Lock (executive) modes
N
See “Setting the front panel locks (Executive modes)” on page 3-4 for more information on the Lock modes.
Lock all front panel functions 1X
Exe1
]
Enable Lock mode 1.
Lock advanced front panel functions 2X
Exe2
]
Enable Lock mode 2.
Unlock all front panel functions 0X
Exe0
]
Enable Lock mode 0.
View lock status X
X&]
Information requests
Information request I
V
X*XX(•AX*XX(] VX*XX( = video size, AX*XX( = audio size
Request part number N
X1)]
Query controller firmware version Q
X1!]
Example:
Q
1.23
]
The factory-installed controller firmware version
is 1.23 (sample value only).
Verbose mode
Set verbose mode
EX1@CV} VrbX1@]
Read verbose mode
ECV} X1@]
N
X& = Lock mode 0, 1, or 2
X* = Inputs Total number of inputs for this switcher
X( = Outputs Total number of outputs for this switcher
X1) = Part number See the MVX VGA A User’s Manual, for a complete list of part numbers.
X1! = Firmware version number to second decimal place (x.xx)
X1@ = Verbose mode 0 = clear/none (default for Telnet connection) 2 = tagged responses for queries
1 = verbose mode (RS-232/RS-422 default) 3 = verbose mode and tagged for queries
MVX VGA A Matrix Switchers • Remote Control
Remote Control, cont’d
4-6
MVX VGA A Matrix Switchers • Remote Control
4-7
Refer also to the MVX VGA A User’s Manual at www.extron.com. Refer also to the MVX VGA A User’s Manual at www.extron.com.
Command ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Lock (executive) modes
N
See “Setting the front panel locks (Executive modes)” on page 3-4 for more information on the Lock modes.
Lock all front panel functions 1X
Exe1
]
Enable Lock mode 1.
Lock advanced front panel functions 2X
Exe2
]
Enable Lock mode 2.
Unlock all front panel functions 0X
Exe0
]
Enable Lock mode 0.
View lock status X
X&]
Information requests
Information request I
V
X*XX(•AX*XX(] VX*XX( = video size, AX*XX( = audio size
Request part number N
X1)]
Query controller firmware version Q
X1!]
Example:
Q
1.23
]
The factory-installed controller firmware version
is 1.23 (sample value only).
Verbose mode
Set verbose mode
EX1@CV} VrbX1@]
Read verbose mode
ECV} X1@]
N
X& = Lock mode 0, 1, or 2
X* = Inputs Total number of inputs for this switcher
X( = Outputs Total number of outputs for this switcher
X1) = Part number See the MVX VGA A User’s Manual, for a complete list of part numbers.
X1! = Firmware version number to second decimal place (x.xx)
X1@ = Verbose mode 0 = clear/none (default for Telnet connection) 2 = tagged responses for queries
1 = verbose mode (RS-232/RS-422 default) 3 = verbose mode and tagged for queries
Installing and Starting the Control Program
Another way to operate the switcher is via the Windows
®
-based
Matrix Switchers Control Program. This program is contained
on the Extron Software Products DVD (included with the
switcher). Run this program on a PC connected to either of the
switcher’s serial ports. See f (page 2-3) and h (page 2-4), for
connection information.The program must be installed on a
Windows-based computer and cannot be run from the DVD.
N
For details on operating the program, refer to the
MVX VGA A Switcher User's Manual, chapter 5,
“Matrix Software”.
Installing the program
1. Insert the disk into the drive. The Extron software DVD
window should appear automatically.
N
If the window does not self-start, run Launch.exe from the
DVD.
2. Click the Software tab.
3. Scroll to the Matrix Switchers program and click Install.
MVX VGA A Matrix Switchers • Remote Control
Remote Control, cont’d
4-8
MVX VGA A Matrix Switchers • Remote Control
4-9
Refer also to the MVX VGA A User’s Manual at www.extron.com. Refer also to the MVX VGA A User’s Manual at www.extron.com.
4. Follow the on-screen instructions. The installation
program creates a C:\Program Files\Extron\
Matrix_Switchers directory and an “Extron Electronics\
Matrix Switchers” group folder. It installs the following
four programs:
• MATRIX Switcher+ Control Program
• MATRIX Switcher+ Help
• Uninstall MATRIX Switcher
• Check for Matrix Updates
Starting the program
1. Click Start > Programs > Extron Electronics > Matrix
Switchers > MATRIX Switcher + Control Pgm.
The Comm Port Selection window appears.
2. Choose the comm (serial) port that is connected to the
switcher.
N
Check the baud rate displayed in the
comm port selection window. If you
need to change the baud rate, click
the Baud button and double-click
the desired baud rate.
Click OK.
The Matrix Switchers Control Program is ready for
operation.
Button-Label Generator Program
The Button Label Generator software creates labels that you can
place in the translucent covers above and below the front panel
input and output buttons. You can create labels with names,
alphanumeric characters, or even color bitmaps for easy and
intuitive input and output selection.
The Extron Button Label Generator is available on the Extron
Web site, www.extron.com, under the Download Center tab
and on the Extron Software Products DVD that accompanies the
switcher.
Refer to the MVX VGA A Switcher User's Manual, chapter 5,
“Matrix Software”, for operating the Button Label Generator
program and appendix A, “Specifications, Part Numbers,
Accessories”, for the procedure for removing and replacing the
translucent covers.
MVX VGA A Matrix Switchers • Remote Control
Remote Control, cont’d
4-10
Refer also to the MVX VGA A User’s Manual at www.extron.com.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19

Extron MVX 1212 VGA A User manual

MVX 1212 VGA A
Extron
Brand
Extron
Model
MVX 1212 VGA A
Category
Video switches
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents