Siemens SIMATIC ET 200eco PN Equipment Manual

SIMATIC

ET 200eco PN

I/O device digital outputs

DQ 8x24VDC/0.5A M12

-L 8xM12

(6ES7142-6BG00-0BB0)

Equipment Manual

07/2020

A5E46570894

-AA

Preface

ET 200eco PN M12-L

Documentation Guide

1

Product overview

2

Wiring

3

Parameters/address space

4

Interrupts/diagnostics

alarms

5

Technical specifications

6

Dimension drawing

A

Siemens AG

Digital Industries

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E46570894-AA

Ⓟ

07/2020 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by personnel qualified for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

Equipment Manual, 07/2020, A5E46570894-AA

3

Preface

Purpose of the documentation

This equipment manual supplements the ET 200eco PN M12-L Distributed I/O System

(https://support.industry.siemens.com/cs/ww/en/view/109778292

) system manual. Functions

that relate in general to the distributed I/O devices ET 200eco PN M12-L are described in this

system manual.

The information provided in this equipment manual and in the system manual and the

function manuals supports you in commissioning the ET 200eco PN M12-L distributed I/O

devices.

Conventions

Also observe notes marked as follows:

Note

A note contains important information:

•

On the product described in the documentation

•

On handling the product

•

On the part of the documentation to which particular attention is paid

Security information

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is

necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens’ products and solutions constitute one element of such a concept.

Customers are responsible for preventing unauthorized access to their plants, systems,

machines and networks. Such systems, machines and components should only be connected

to an enterprise network or the internet if and to the extent such a connection is necessary

and only when appropriate security measures (e.g. firewalls and/or network segmentation)

are in place.

For additional information on industrial security measures that may be implemented, please

visit (https://www.siemens.com/industrialsecurity

).

Siemens' products and solutions undergo continuous development to make them more

secure. Siemens strongly recommends that product updates are applied as soon as they are

available and that the latest product versions are used. Use of product versions that are no

longer supported, and failure to apply the latest updates may increase customers' exposure to

cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed visit (https://www.siemens.com/industrialsecurity

).

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

4 Equipment Manual, 07/2020, A5E46570894-AA

Table of contents

Preface ................................................................................................................................................... 3

1 ET 200eco PN M12-L Documentation Guide .......................................................................................... 5

2 Product overview ................................................................................................................................... 9

2.1 Properties ............................................................................................................................ 9

2.2 Operator controls and display elements ............................................................................. 11

3 Wiring .................................................................................................................................................. 12

3.1 Terminal and block diagram ............................................................................................... 12

3.2 Pin assignment .................................................................................................................. 14

4 Parameters/address space ................................................................................................................... 18

4.1 Parameters ........................................................................................................................ 18

4.2 Explanation of the parameters ........................................................................................... 19

4.3 Address space .................................................................................................................... 20

5 Interrupts/diagnostics alarms .............................................................................................................. 24

5.1 Status and error displays .................................................................................................... 24

5.2 Interrupts .......................................................................................................................... 27

5.3 Alarms ............................................................................................................................... 28

5.3.1 Diagnostics alarms ............................................................................................................. 28

5.3.2 Maintenance events .......................................................................................................... 29

6 Technical specifications ....................................................................................................................... 30

A Dimension drawing ............................................................................................................................. 35

A.1 Dimension drawing............................................................................................................ 35

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

Equipment Manual, 07/2020, A5E46570894-AA

5

ET 200eco PN M12-L Documentation Guide

1

The documentation for the SIMATIC ET 200eco PN M12-L distributed I/O system is arranged

into three areas. This arrangement enables you to access the specific content you require.

Basic information

The system manual describes in detail the configuration, installation, wiring and

commissioning of the SIMATIC ET 200eco PN M12-L distributed I/O system. The STEP 7 online

help supports you in the configuration and programming.

Device information

Product manuals contain a compact description of the module-specific information, such as

properties, interfaces, wiring diagrams, display and operator control elements and technical

specifications.

General information

The function manuals contain detailed descriptions on general topics relating to the SIMATIC

ET 200eco PN M12-L distributed I/O system, e.g. diagnostics, communication and PROFINET.

You can download the documentation free of charge from the Internet

(https://support.industry.siemens.com/cs/de/en/view/109742718

).

ET 200eco PN M12-L Documentation Guide

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

6 Equipment Manual, 07/2020, A5E46570894-AA

"mySupport"

With "mySupport", your personal workspace, you make the best out of your Industry Online

Support.

In "mySupport", you can save filters, favorites and tags, request CAx data and compile your

personal library in the Documentation area. In addition, your data is already filled out in

support requests and you can get an overview of your current requests at any time.

You must register once to use the full functionality of "mySupport".

You can find "mySupport" on the Internet (https://support.industry.siemens.com/My/ww/en

).

Application examples

The application examples support you with various tools and examples for solving your

automation tasks. Solutions are shown in interplay with multiple components in the system -

separated from the focus on individual products.

You will find the application examples on the Internet

(https://support.industry.siemens.com/sc/ww/en/sc/2054

).

TIA Selection Tool

With the TIA Selection Tool, you can select, configure and order devices for Totally Integrated

Automation (TIA).

This tool is the successor of the SIMATIC Selection Tool and combines the known

configurators for automation technology into one tool.

With the TIA Selection Tool, you can generate a complete order list from your product

selection or product configuration.

You can find the TIA Selection Tool on the Internet

(https://w3.siemens.com/mcms/topics/en/simatic/tia-selection-tool

).

ET 200eco PN M12-L Documentation Guide

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

Equipment Manual, 07/2020, A5E46570894-AA

7

SIMATIC Automation Tool

You can use the SIMATIC Automation Tool to perform commissioning and maintenance

activities simultaneously on various SIMATIC S7 stations as a bulk operation independent of

TIA Portal.

The SIMATIC Automation Tool provides a multitude of functions:

• Scanning of a PROFINET/Ethernet system network and identification of all connected CPUs

• Address assignment (IP, subnet, gateway) and station name (PROFINET device) to a CPU

• Transfer of the date and the PG/PC time converted to UTC time to the module

• Program download to CPU

• RUN/STOP mode switchover

• CPU localization by means of LED flashing

• Reading out of CPU error information

• Reading the CPU diagnostics buffer

• Reset to factory settings

• Firmware update of the CPU and connected modules

You can find the SIMATIC Automation Tool on the Internet

(https://support.industry.siemens.com/cs/ww/en/view/98161300

).

PRONETA

SIEMENS PRONETA (PROFINET network analysis) allows you to analyze the plant network

during commissioning. PRONETA features two core functions:

• The topology overview automatically scans the PROFINET and all connected components.

• The IO check is a fast test of the wiring and the module configuration of a system.

You can find SIEMENS PRONETA on the Internet

(https://support.industry.siemens.com/cs/ww/en/view/67460624

).

ET 200eco PN M12-L Documentation Guide

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

8 Equipment Manual, 07/2020, A5E46570894-AA

SINETPLAN

SINETPLAN, the Siemens Network Planner, supports you in planning automation systems and

networks based on PROFINET. The tool facilitates professional and predictive dimensioning of

your PROFINET installation as early as in the planning stage. In addition, SINETPLAN supports

you during network optimization and helps you to exploit network resources optimally and to

plan reserves. This helps to prevent problems in commissioning or failures during productive

operation even in advance of a planned operation. This increases the availability of the

production plant and helps improve operational safety.

The advantages at a glance

• Network optimization thanks to port-specific calculation of the network load

• Increased production availability thanks to online scan and verification of existing systems

• Transparency before commissioning through importing and simulation of existing STEP 7

projects

• Efficiency through securing existing investments in the long term and the optimal use of

resources

You can find SINETPLAN on the Internet (https://www.siemens.com/sinetplan

).

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

Equipment Manual, 07/2020, A5E46570894-AA

9

Product overview

2

2.1 Properties

Article number

6ES7142-6BG00-0BB0

View of the I/O device

Figure 2-1 View of the I/O device DQ 8x24VDC/0.5A M12-L 8xM12

Product overview

2.1 Properties

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

10 Equipment Manual, 07/2020, A5E46570894-AA

Properties

The I/O device has the following technical properties:

• 8 digital outputs

• M12 sockets for connection of actuators

• Rated supply voltage 24 V DC

• Rated load voltage 24 V DC

• Integrated switch with 2 ports

• Single and dual assignment of the sockets

• Configurable diagnostics can be set for each channel

• Output current per output 0.5 A

• Total current max. 4 A (per I/O device)

• Suitable for solenoid valves, DC contactors, and indicator lights

• Dimensions 45 x 200 mm

The I/O device supports the following functions:

• Firmware update

• Identification and maintenance data I&M0 to I&M3

• Isochronous mode

• Value status (Quality Information)

• Module-internal Shared Output (MSO)

• Shared Device

Accessories

The following components are included in the I/O device package:

• Identification labels

Other components

The following component can be ordered as spare part:

• Identification labels

The following components can be ordered as accessories:

• Mounting rail

• Connectors and cables

• M12 sealing cap

See also

You can find additional information on the accessories in the ET 200eco PN M12-L distributed

I/O system system manual.

Product overview

2.2 Operator controls and display elements

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

Equipment Manual, 07/2020, A5E46570894-AA

11

2.2 Operator controls and display elements

The figure below shows the operator controls and display elements of the

DQ 8x24VDC/0.5A M12-L 8xM12 I/O device.

①

PN/MF (LAN): Sockets for connecting PROFINET

②

RN/NS: RUN/network status LED

③

ER/MS: ERROR/module status LED

④

MT/IO: MAINT/IO status LED

⑤

PWR: Power LED for load voltage 2L+

⑥

P1 LK/P2 LK: LINK port status LEDs

⑦

LED displays 0 to 7 for channel status/channel error

⑧

X10 to X17: Sockets for the output signal

⑨

X80: Connector for infeed of supply and load voltage

⑩

X81: Socket for loop-through of the supply and load voltage

Figure 2-2 Operator controls and display elements

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

12 Equipment Manual, 07/2020, A5E46570894-AA

Wiring

3

3.1 Terminal and block diagram

The figure below shows an example of the pin assignment of signal outputs with single and

dual assignment of the sockets.

Wiring

3.1 Terminal and block diagram

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

Equipment Manual, 07/2020, A5E46570894-AA

13

①

Bus interface with integrated 2-port switch

1L+

Supply voltage 1L+ (non-switched)

②

Monitoring

1M

Ground 1M (non-switched)

③

DQ circuit

2L+

Load voltage 2L+ (switched)

④

Internal supply voltage

2M

Ground 2M (switched)

⑤

Output (dual assignment of the socket)

DQn

Output signal

⑥

Output (single assignment of socket)

RN/NS

RUN/network status LED (green)

⑦

Output (single assignment of socket)

ER/MS

ERROR/module status LED (red)

X10 to X17

Channels 0 to 7

MT/IO

MAINT/IO status LED (yellow)

X80

Infeed of supply and load voltage

P1 LK

LINK port 1 LED (green)

X81

Loop-through of supply and load voltage

P2 LK

LINK port 2 LED (green)

X1 P1R PROFINET interface X1 port 1 DQ Channel status/channel error LED

(green/red)

X1 P2R

PROFINET interface X1 port 2

PWR

LED load voltage 2L+ (green)

Figure 3-1 Terminal and block diagram

Wiring

3.2 Pin assignment

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

14 Equipment Manual, 07/2020, A5E46570894-AA

3.2 Pin assignment

Terminal assignment PROFINET connector

The following table shows the pin assignment of the PROFINET connector.

Table 3- 1 Pin assignment of the PROFINET connector, port 1 and 2

Assignment of the core

color of the PROFINET

cable

Assignment Front view of the connectors

Assignment X1 P1R

1

Yellow

TXP

2

White

RXP

3

Orange

TXN

4

Blue

RXN

Thread

Functional earth FE

Assignment X1 P2R

1

Yellow

RXP

2

White

TXP

3

Orange

RXN

4

Blue

TXN

Thread

Functional earth FE

Wiring

3.2 Pin assignment

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

Equipment Manual, 07/2020, A5E46570894-AA

15

Pin assignment of sockets for digital outputs

The table below shows the pin assignment of the 8 sockets for the connection of the digital

outputs.

Table 3- 2 Pin assignment for digital outputs

Assignment

Front view of the sockets

X10 to X17 - sockets for digital outputs X10, X12,

X14, X16

X11, X13,

X15, X17

1

-

2

Connector X10: Output signal DQ

1

*

Connector X11: Not assigned

Connector X12: Output signal DQ

3*

Connector X13: Not assigned

Connector X14: Output signal DQ

5*

Connector X15: Not assigned

Connector X16: Output signal DQ

7*

Connector X17: Not assigned

3

Ground 2M

4

Connector X10: Output signal DQ

0

Connector X11: Output signal DQ1*

Connector X12: Output signal DQ

2

Connector X13: Output signal DQ

3*

Connector X14: Output signal DQ

4

Connector X15: Output signal DQ

5*

Connector X16: Output signal DQ

6

Connector X17: Output signal DQ7*

5

Functional earth FE

* Note the assignment of the output signals to the respective sockets in the foll

owing section "Dual

assignment of the sockets".

Dual assignment of the sockets

There are two output signals at the sockets X10, X12, X14 and X16 of the I/O device. Pin 2 of

the respective socket is assigned an additional output signal.

Note

Dual or sin

gle assignment of sockets

You can select the dual and single assignment of sockets as desir

ed.

Note that the output signals DQ

1, DQ3, DQ5 and DQ7

are each parallel to the sockets X10/X11,

X12/X13, X14/X15, X16/X17.

Wiring

3.2 Pin assignment

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

16 Equipment Manual, 07/2020, A5E46570894-AA

The following graphic shows the assignment of the output signals to the respective sockets

with dual or single assignment.

Figure 3-2 Assignment of output signals with dual or single assignment of sockets

Pin assignment of the connector for infeed of the supply voltage (M12 L-coded)

The table below shows the pin assignment of the M12 L-coded connector for infeed of the

supply voltage.

Table 3- 3 Pin assignment of the supply voltage connector

Assignment of the

core color of the

power cable

Assignment

Front view of the

connector

X80 - connector (POWER input)

1

Brown

Supply voltage 1L+ (non-switched)

2

White

Ground 2M (switched)

3

Blue

Ground 1M (non-switched)

4

Black

Load voltage 2L+ (switched)

Wiring

3.2 Pin assignment

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

Equipment Manual, 07/2020, A5E46570894-AA

17

Pin assignment of the socket for loop-through of the supply voltage (M12 L-coded)

The table below shows the pin assignment of the M12 L-coded socket for loop-through of the

supply voltage.

Table 3- 4 Pin assignment of the supply voltage socket

Assignment of the

core color of the

power cable

Assignment

Front view of the

socket

X81 - socket (POWER output)

1

Brown

Supply voltage 1L+ (non-switched)

2

White

Ground 2M (switched)

3

Blue

Ground 1M (non-switched)

4

Black

Load voltage 2L+ (switched)

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

18 Equipment Manual, 07/2020, A5E46570894-AA

Parameters/address space

4

4.1 Parameters

The table below shows the parameters for the I/O device DQ 8x24VDC/0.5A M12-L 8xM12.

Table 4- 1 Configurable parameters and their defaults (GSD file)

Parameters Value range Default

Scope with configu-

ration software, e.g.

STEP 7 (TIA Portal)

Diagnostics: Undervoltage 1L+

• Disable

• Enable

Disable

Channel

Diagnostics: Missing 2L+

• Disable

•

Enable

Disable

Channel

Diagnostics: Short-circuit

• Disable

• Enable

Disable

Channel

Diagnostics: Wire break

• Disable

•

Enable

Disable

Channel

Reaction to CPU STOP

• Shutdown

• Keep last value

• Output substitute value 1

Shutdown

Channel

Parameters/address space

4.2 Explanation of the parameters

I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)

Equipment Manual, 07/2020, A5E46570894-AA

19

4.2 Explanation of the parameters

Diagnostics: Undervoltage 1L+

Enabling of diagnostics for insufficient supply voltage 1L+.

Diagnostics: Undervoltage 1L+ triggers the "Undervoltage" maintenance event. You can find

more information in section Maintenance events (Page 29).

Diagnostics: Missing 2L+

Enabling of the diagnostics for missing or insufficient load voltage 2L+.

Diagnostics: Short-circuit

Enabling of the diagnostics for short-circuit of the output to ground.

Diagnostics: Wire break

Enabling of diagnostics when the line between the actuator and the I/O device is interrupted.

Reaction to CPU STOP

With this parameter, you set the reaction of the digital outputs of the I/O device after a CPU

STOP:

• Shutdown: The digital output is de-energized.

• Keep last value: The last value of the digital output remains activated.

• Output substitute value 1: The I/O device outputs the substitute value "1".

Page is loading ...

Siemens SIMATIC ET 200eco PN Equipment Manual

This manual is also suitable for

Siemens SIMATIC ET 200eco PN Equipment Manual

Related papers

Other documents