Hytera BD352i Owner's manual

数字手持终端

DIGITAL PORTABLE RADIO

BD352i OWNER’S MANUAL

BD35

使用说明书

Welcome to the world of Hytera and thank you for purchasing this product. This manual

includes a description of the functions and step-by-step procedures for use. It also includes

a troubleshooting guide. To avoid bodily injury or property loss caused by incorrect

operation, please carefully read the Safety Information Booklet before use.

This manual is applicable to the following product:

BD352i Digital Portable Radio

Hytera is the trademark or registered trademark of Hytera Communications

Corporation Limited (the Company) in the People's Republic of China (PRC)

and/or other countries or areas. The Company retains the ownership of its

trademarks and product names. All other trademarks and/or product names

that may be used in this manual are properties of their respective owners.

The product described in this manual may include the Company's computer

programs stored in memory or other media. Laws in PRC and/or other

countries or areas protect the exclusive rights of the Company with respect

to its computer programs. The purchase of this product shall not be deemed

to grant, either directly or by implication, any rights to the purchaser

regarding the Company's computer programs. The Company's computer

programs may not be copied, modified, distributed, decompiled, or reverse-

engineered in any manner without the prior written consent of the Company.

Disclaimer

The Company endeavors to achieve the accuracy and completeness of this

manual, but no warranty of accuracy or reliability is given. All the

specifications and designs are subject to change without notice due to

continuous technological development. No part of this manual may be

copied, modified, translated, or distributed in any manner without the prior

written consent of the Company.

We do not guarantee, for any particular purpose, the accuracy, validity,

timeliness, legitimacy or completeness of the third-party products and

contents involved in this manual.

If you have any suggestions or would like to receive more information,

please visit our website at: http://www.hytera.com.

FCC Statement

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates and can radiate radio

frequency energy. If not installed and used in accordance with the

instructions, it may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. Verification of harmful interference by this

equipment to radio or television reception can be determined by turning it

off and then on. The user is encouraged to try to correct the interference by

one or more of the following measures:

·Reorient or relocate the receiving antenna. Increase the separation

between the equipment and receiver.

·Connect the equipment into an outlet on a different circuit to that of the

receiver's outlet.

·Consult the dealer or an experienced radio/TV technician for help.

Operation is subject to the following two conditions:

·This device may not cause harmful interference.

·This device must accept any interference received, including

interference that may cause undesired operation.

Note: Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user's authority to operate

the equipment.

Compliance with RF Exposure Standards

Hytera's portable radio complies with the following RF energy exposure

standards and guidelines:

·United States Federal Communications Commission, Code of Federal

Regulations; 47 CFR § 1.1307, 1.1310 and 2.1093.

·American National Standards Institute (ANSI) / Institute of Electrical

and Electronic Engineers (IEEE) C95. 1:2005; Canada RSS102 Issue 5

March 2015.

·Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005

Edition

RF Exposure Compliance and Control

Guidelines and Operating Instructions

To control your exposure and ensure compliance with the

occupational/controlled environmental exposure limits, always adhere to the

following procedures.

Guidelines:

·Do not remove the RF Exposure Label from the device.

·User awareness instructions should accompany device when transferred

to other users.

·Do not use this device if the operational requirements described herein

are not met.

Operating Instructions:

·Transmit no more than the rated duty factor of 50% of the time. To

transmit (talk), push the Push-To-Talk (PTT) button. To receive calls,

release the PTT button. Transmitting 50% of the time, or less, is

important because the radio generates measurable RF energy only when

transmitting (in terms of measuring for standards compliance).

·Keep the radio unit at least 2.5 cm away from the face. Keeping the

radio at the proper distance is important as RF exposure decreases with

distance from the antenna. The antenna should be kept away from the

face and eyes.

·When worn on the body, always place the radio in a Hytera-approved

holder, holster, case, or body harness or by use of the correct clip for

this product. Use of non-approved accessories may result in exposure

levels which exceed the FCC's occupational/controlled environmental RF

exposure limits.

·Use of non-approved antennas, batteries, and accessories causes the

radio to exceed the FCC RF exposure guidelines.

·Contact your local dealer for the product's optional accessories.

IC Statement

The device has been tested and complies with SAR limits, users can obtain

Canadian information on RF exposure and compliance

Après examen de ce matériel aux conformité aux limites DAS et/ou aux

limites d’intensité de champ RF, les utilisateurs peuvent sur l’exposition aux

radiofréquences et la conformité and compliance d’acquérir les

informations correspondantes

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions:

·This device may not cause harmful interference.

·This device must accept any interference received, including

interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables

aux appareils radio exempts de licence. L'exploitation est autorisée aux

deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage,

et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d'en compromettre le

fonctionnement

EU Regulatory Conformance

As certified by the qualified laboratory, the product is in compliance with

the essential requirements and other relevant provisions of the following

directives: 1999/5/EC or 2014/53/EU, 2006/66/EC, 2011/65/EU, and

2012/19/EU.

Please note that the above information is applicable to EU countries only.

Contents

Packing List

Product Overview 3

Product Controls 3

LCD Icons 4

LED Indications 4

Before Use 4

Attaching the Antenna 4

Attaching the Battery 4

Attaching the Belt Clip 5

Attaching the Audio Accessories 5

Charging the Battery 5

Checking the Battery Power 5

Basic Operations 6

Call Services 6

Call on Digital Channel 6

Call on Analog Channel (Without Signaling) 6

Optional Features 7

Troubleshooting 9

Care and Cleaning

Product Care

Product Cleaning 11

Optional Accessories

Product Care

Contents

Packing List

Please unpack carefully and check that all items listed below are received. If any item is missing or damaged, please contact your dealer.

Item Quantity (PCS) Item Quantity (PCS)

Radio 1Belt Clip 1

Battery 1Strap 1

Power Adapter 1Documentation Kit 1

Antenna 1//

Check whether the frequency band marked on the antenna label matches that on the radio label. If not, please contact your dealer.

Product Overview

Product Controls

You can request your dealer to program your radio to use the SK as the shortcut to a radio feature.

LCD Icons

LED Indications

LED Indicator Radio Status

Flashes green Being turned on.

Glows green Receiving.

Glows red Transmitting.

Flashes orange slowly Scanning.

Glows orange

Call hang time: No voice is being transmitted or

received on the channel during a call. Within such

a period, you can press and hold the PTT key and

speak.

Before Use

Attaching the Antenna

1. Place the antenna in its receptacle.

2. Rotate the antenna clockwise until hand tight.

Do not hold the radio by the antenna, as it may reduce the radio

performance and life span of the antenna.

Attaching the Battery

1. Slide the battery latch to the unlock position, and remove the battery

cover.

2. Align the battery contacts with the contacts in the battery compartment,

and press the battery into place.

3. Insert the protrusions at the top of the battery cover into the radio, and

press the cover into place.

4. Slide the battery latch to the lock position.

To remove the battery, make sure the radio is turned off, remove the

battery cover, and lift the bottom of the battery.

Attaching the Belt Clip

1. Use a Phillips screwdriver to turn the screws counterclockwise on the

back of the radio and remove them.

2. Align the screw holes on the belt clip with those on the back of the radio.

3. Put the screws back in place, and use the Phillips screwdriver to turn them

clockwise until hand tight.

Attaching the Audio Accessories

1. Open the accessory connector cover.

2. Plug the accessory into the accessory connector.

3. Rotate the accessory plug clockwise into place.

Charging the Battery

·Use the charger specified by Hytera to charge the battery.

·Read the Safety Information Booklet before charging.

The battery delivered with the radio is uncharged. To ensure optimum

performance, fully charge the battery before initial use. It is recommended

that your radio remain powered off during charging.

To charge the battery, do as follows:

1. Insert the USB connector of the power adapter into the USB port of the

radio.

2. Plug the power adapter into a power outlet, and then switch the power out-

let on

Checking the Battery Power

To check the current battery power, press and hold the Battery Power

Indicator key preprogrammed by your dealer. The following table lists

battery power indications. The icon indicates that the battery runs low.

In this case, please recharge or replace the battery

LED Indicator Alert Tone Battery Power

Glows green Three beeps

Glows orange Two beeps

Glows red One beep

Flashes red Low battery tone

Basic Operations

If you want to… Then…

Turn on/off the radio Press the On-Off key.

Increase the volume Press the Volume Up key.

Decrease the volume Press the Volume Down key.

Select a channel Rotate the Channel Selector knob.

Call Services

Call on Digital Channel

You can initiate a call to or receive a call from the private or group contact

preset for a digital channel.

Initiating a Call

1. Select the required channel.

2. Hold the radio vertically 2.5 to 5 cm from your mouth.

3. Press and hold the PTT key, and then speak into the microphone.

The radio displays for an outgoing group call and for an outgoing

private call.

Receiving and Responding to a Call

When receiving a call, you can listen to it without any operation. The radio

displays for an incoming group call and for an incoming private

call.

You can press and hold the PTT key and speak within the preset time

period.

Call on Analog Channel (Without Signaling)

You can initial a call to or receive calls from all other users on an analog

channel. The operations are the same as those on a digital channel.

Optional Features

The following features need to be programmed by your dealer. Please contact your dealer for detailed operations.

Type Feature Description

General

Feature

Zone Allows you to select a zone. The radio supports up to 16 zones, with a maximum of 256 channels per zone.

Power Level Allows you to switch the transmit power level between high and low.

Scan Allows the radio to scan all channels in the scan list preset for the current channel and stay on a channel with activities.

Emergency Alarm Allows you to initiate an emergency alarm or call to ask for help in case of emergencies.

Busy Channel Lockout Prevents the radio from transmitting on a busy channel.

Time-out Timer (TOT) Terminates transmission when the preset time period expires.

Keypad Lock Allows the keypad to be locked automatically when the radio does not detect any activity or operation within the preset

period.

Battery Save Allows the radio to automatically enter the battery save mode when it does not detect any activity or operation within the

preset period.

Digital

Feature

All Call Allows you to initiate a call to all users on a digital channel.

One Touch Call Allows you to press one key to call the predefined private or group contact.

TDMA Direct Mode Allows the radio to operate on a channel with two time slots.

Type Feature Description

Analog

Feature

Squelch Off Allows the radio's speaker to always keep unmuted.

Squelch Off Momentary Allows the radio's speaker to keep unmuted when you press and hold the preprogrammed key.

Squelch Level Allows you to adjust the squelch threshold required for the radio to unmute.

Monitor Allows the radio to monitor activities on the channel.

Scrambler Allows you to encrypt the transmitted voice to prevent eavesdropping.

CTCSS/CDCSS Allows you to prevent unwanted calls on the same frequency.

Troubleshooting

Phenomena Analysis Solution

The radio cannot be

turned on.

The battery may be installed improperly. Remove and reattach the battery.

The battery power may run out. Recharge or replace the battery.

The battery may suffer from poor contact caused by dirty or

damaged battery contacts. Clean the battery contacts or replace the battery.

During reception, the

voice is weak, intermittent

or totally inactive.

The battery voltage may be low. Recharge or replace the battery.

The volume level may be low. Increase the volume.

The antenna may be loose or may be installed incorrectly. Turn off the radio, and remove and reattach the antenna.

The speaker may be blocked. Clean the surface of the speaker.

You cannot communicate

with other group members.

The frequency or signal strength may be low in comparison

to other members. Verify your TX/RX frequency and signal strength are correct.

The channel type (digital or analog) may be set incorrectly. Verify you are on the correct digital or analog channel.

You may be too far away from other members. Move towards other members.

Unknown voices or noise

is heard on the channel.

You may be interrupted by radios using the same frequency. Change the frequency, or adjust the squelch level.

The radio in analog mode may be set with no signaling. Set signaling for all radios operating at the same frequency to avoid

interference.

Phenomena Analysis Solution

You are unable to hear

anyone because of too

much noise and hiss.

You may be too far away from other members. Move towards other members.

You may be located in an unfavorable position. For

example, your communication may be blocked by high

buildings or blocked in an underground area.

Move to an open and flat area, and restart the radio and try

contacting again.

It could be the result of external disturbance (such as

electromagnetic interference). Stay away from equipment that may cause interference.

The OLED does not

display any information. The OLED may fail to function temporarily. Restart the radio.

If the above solutions cannot fix your problems, or you may have some

other queries, please contact us or your local dealer for more technical

support.

If the above solutions cannot fix your problems, or you may have some other queries, please contact us or your local dealer for more technical support.

Care and Cleaning

To guarantee optimal performance as well as a long service life of the

product, please follow these tips.

Product Care

·Do not pierce or scrape the product.

·Keep the product far away from substances that can corrode the

circuitry.

·Do not hold the product by the antenna or earpiece cable.

·Close the accessory connector cover when no accessory is in use.

Product Cleaning

Turn off the product and remove the battery before cleaning.

·Clean up the dust and fine particles on the products surface and

charging piece with a clean and dry lint-free cloth or a brush regularly

·Use neutral cleanser and a non-woven fabric to clean the keys, knobs

and front case after long-time use. Do not use chemical preparations

such as stain removers, alcohol, sprays or oil preparations, so as to avoid

surface case damage.

·Make sure the product is completely dry before use.

Optional Accessories

Use the accessories specified by Hytera only; otherwise, the Company

will not be liable for any loss or damage arising out of the use of any

unauthorised accessories.

Contact your local dealer for the optional accessories used with the product.

非常感谢您对我们产品的青睐！本手册旨在让您快速掌握终端的使用。为了避免因不

当操作而给您带来身体伤害或财产损失，请于使用终端前详细阅读《安全信息手

册》。

本手册适用于以下机型：

BD352i数字手持终端

版权信息

Hytera为海能达通信股份有限公司（以下简称“我司”）在中华人民共和国和世界其他国家和/或地区的商标或注册商标。我司仅对自有商标及产品名

称享有所有权，本手册中可能提及的其他商标和产品名称为各自所有者所有。

本手册介绍的产品中可能包括存储于内存或其他媒介中的计算机程序。我司对此等程序享有的专有权利受中华人民共和国或其他国家及相关国际法的

保护。购买本产品并不意味着我司以明示或暗示方式向购买者授予有关此等电脑程序的权益。未经我司事先书面授权，任何企业、组织或个人不得对

计算机程序进行任何形式的复制、更改、散发、反编译和反向工程。

免责声明

本手册在编制过程中力求内容的准确性与完整性，但对于可能出现的错误或疏漏，我司不承担任何责任。由于技术的不断发展，我司保留不予通知而

更改产品设计与规格的权利。未经我司事先书面授权，不得以任何形式对本手册进行复制、修改、翻译和散发。

本手册中涉及的第三方产品和内容归第三方所有，我司对其准确性、有效性、及时性、合法性或完整性均不提供保证。

如需更多信息或对本手册有任何建议，欢迎访问我们的网站：http://www.hytera.com，或拨打我司服务热线：400-830-7020。

美国联邦通信委员会监管要求

按照美国联邦通信委员会的监管要求，终端必须符合美国联邦通信委员会射频辐射限制规定，否则不能在美国市场上销售。并要求制造商可通过在产

品上张贴标签的方式，告知用户应注意的事项，提高用户的防辐射意识。

射频辐射控制及操作说明

为了使产品发挥最佳性能及确保符合上述标准中有关职业或受控环境中的辐射限制要求，发送时间不得超过额定因数的50%（最高50%的时间发

射），且需遵照下列说明：

l仅在发射（讲话）时产生射频能量辐射，接收（收听）和待机时均不会产生。

l发射时终端与身体的距离至少保持在2.5厘米以上。

包装清单 2

熟悉产品 3

部件介绍 3

状态图标 4

LED指示灯 4

用前准备 4

安装天线 4

安装电池 4

安装皮带夹 4

安装音频附件 5

充电 5

查看电量 5

基本操作 6

呼叫 6

数字信道呼叫 6

模拟信道呼叫（无信令）

功能说明

故障处理 9

保养与清洁 11

保养 11

清洁 11

选购配件 11

保修范围与期限 11

功能说明

包装清单

包装盒内含有以下物品。如有任何物品丢失或损坏，请与您所购产品的经销商联系。

物品数量物品数量

主机 1 皮带夹 1

电池 1 电池盖 1

电源适配器 1 吊绳 1

天线 1 资料套件 1

请检查电池槽内的主机标签及天线底部色环标签，以确保所购产品无误。

Page is loading ...

Hytera BD352i Owner's manual

Related papers

Other documents