Electrolux GHL346SW Installation guide
- Category
- Hobs
- Type
- Installation guide
This manual is also suitable for
EN Installation Instructions
1. INSTALLATION INSTRUCTIONS
1.1 General information
• Connection and commissioning of the
gas cooker must be in conformity with
local and national law and regulations.
Only a qualified person must install
the appliance.
• The connection must be confirmed by
a signature of the person installing the
appliance on the warranty card.
• Use only the original connector board
of the built-in appliance.
• During installation and commissioning
the appliance must be disconnected
from the gas and electrical supply.
• During any maintenance or repairs
the main gas valve must be closed
and the appliance must be unplugged
from the power supply or the fuses
must be released, depending on the
connection.
• The general rules applicable to using
gas appliances and electrical
appliances and the current directives /
instructions concerning the installation
must be strictly obeyed.
1.2 Delivery and packaging
Make sure that the appliance
is in good condition after
transport. Any damage must
be reported immediately and
the appliance should not be
put into service.
Packaging
• The whole packaging is recyclable.
Check the packaging foil and
styrofoam for the recycling symbols.
• Dispose of the packaging materials
and the appliance, when necessary,
in accordance with the applicable
standards.
• Refer to the local and national
regulations on disposal and read the
labels of the packaging materials.
There is information on sorting the
materials, collection of the used
appliances and proper places of
disposal.
1.3 Hob installation accessories
• 8 screws for fixing the burners grate,
• 2 screws for fixing the hob in place
with the pan support on top with
protective conductor,
• 4 screws to install the hob on the work
surface,
• 8 screws for securing the burners plus
2 spare,
• 2 pan supports.
1.4 Glass plate installation
accessories
• Seal,
• 8 screws for the plywood panel 3.5 x
25 to secure the burner,
• 4 enamelled joints for the burner,
• 4 rubber gaskets,
• 8 screws 2.9 x 13 for securing the
burners on the hob plus 2 spare,
• 2 pan supports.
1.5 Oven installation accessories
• Burner caps and crowns for the 4
burners,
• 4 screws for securing the oven in
place.
1.6 Requirements for built-in
Make sure that during installation the
appliance is disconnected from the power
supply and take precautions against
possible ignition.
Pay special attention during installation of
the back wall of the appliance. After the
installation it will not be easily accessible,
even if there is a distance between it and
the wall.
The furniture where the appliance is built-
in and adjacent to it should be stable.
The furniture where the appliance is built-
in, the furniture adjacent to it as well as
any synthetic surfaces coatings and glues
near it should be able to safely withstand
the temperatures of at least 95 ⁰C.
Any surface coatings and glues not able to
withstand this temperature can cause
deformation of the furniture and unsticking
www.electrolux.com2
of the parts near the oven. Contact the
furniture producer in case of any doubts.
This appliance of the third class is
designed to be built-in in kitchen furniture.
The wall behind the appliance and wall of
the piece of furniture next to it can have
any height.
The piece of furniture on the other side
must be on the same level as the hob.
Keep the required minimal distances as
measured in relation to the hob:
• 100 mm on any side to the nearest
piece of furniture,
• 100 mm at the back of the worktop
cut-out to the rear edge of the
worktop,
• 560 mm from the surface of the hob to
the piece of furniture / appliance
above it.
1.7 Flap
The flap is in the lower part of the
appliance.
This is not a storage drawer.
Do not use it as a storage.
Gas connection is installed
under the appliance.
1.8 Gas connection
The gas pipe gasket is in a
bag inside the oven.
Check the factory settings of the
appliance on the rating plate.
The appliance is set for natural gas H 20
mbar.
In case of conversion to different type of
gas, the label should be taken off and
replaced with a new technical label with
the correct data.
The connection to the gas supply should
be permanent.
The appliance should be connected by a
steel-only hose fitted with a safety device
and with a homologation of SGWA (Swiss
Gas and Water Industry Association).
1
2
N 550
A 548 +0/-1
min. 50
3
4
A 572
N 600
20
150
1. G 1/2" coupler installed at the height
of 160 mm from the ground, to be
installed with at least a flange.
2. Valve to cut off the gas G1/2.
3. Metal tube 50 cm with G1/2 internal
thread, connected to the valve
through a gasket.
Gas protection installation
Install the protection to secure the gas
pipe.
1. Place the metal cover plate over the
pipe.
2. Secure the plate with two screws.
ENGLISH
3
1.9 Electrical connection
Standard socket, type 13.
The electrical installation must have an
isolation device which lets you disconnect
the appliance from the main power supply
at all poles. The isolation device must have
a contact opening width of minimum 3
mm.
Use only correct isolation devices: line
protecting cut-outs, fuses, earth leakage
trips and contactors. Screw type fuses
must be removed from the holder.
Before the connection make sure that the
voltage on the rating plate, nominal
voltage of the oven, agrees with the power
supply. The rating plate can be found on
the frame of the appliance, open the door
to access it.
The voltage of the heaters is 230 V AC,
but the appliance can also function
correctly on the 220 V AC.
The electrical cable cannot touch the back
wall of the built-in appliance.
The socket must be easily accessible.
160
1
1. Rating plate
1.10 Build-in gas hob
GKM45GLAS and GKM45CN
Prepare the cut-out in the worktop to
place the hob:
• The cut-out should be placed in the
center of the worktop where the
appliance is installed.
• Make the cut-out in the worktop
according to the dimensions
presented below. Too deep cut-out
must be corrected for example by a
wooden surround.
• Seal the cut surface with an
appropriate heat resistant sealant to
protect it from humidity.
• Preserve the minimal distances:
– 100 mm on any side to the
nearest piece of furniture,
– 100 mm at the back of the
worktop cut-out to the rear edge
of the worktop,
– 560 mm from the surface of the
hob to the piece of furniture /
appliance above it.
R5
560 1
55
20
20-50
=
=
490 1
+
-
+
-
20
55
1
2
3
1. The cut-out
2. The table / work surface
3. Front furniture panel
The worktop should surround the hob on
every side.
Adjusting the dimensions in the process of
redecoration / refurbishment.
Cut-outs with dimensions different from
those above have to be adjusted
according to the explanations and
measurements in the tables below.
www.electrolux.com4
1. Build-in gas oven with hob 1985 - 1997
without wooden surround
R5
544 (560)
55 (36)
20
20-50
490 (526)
Cut-out for the hob in a synthetic resin or
stone worktop
Width (mm) Depth (mm)
544 - 560 490
2. Build-in gas oven with hob from 1985
with a wooden surround ARGH600/58
R5
B
T
45
490
43
588
55
542
600
20
20-50
Cut-out for the hob in a synthetic resin or
stone worktop
Width (mm) Depth (mm)
600 - 542 588 -490
3. Gas cooker built in worktop of chrome
plated stamped steel 1, 2 or 3. With a
wooden surround ARGH600/58
Cut-out for the hob in chrome plated
steel surfaces
Width (mm) Depth (mm)
Should be done in accordance with sep-
arate instructions for cutting out and in-
stallation
1.11 Installing the oven
Make sure that the dimensions marked
with N in the picture of the niche where
the oven is installed are correct and exact.
The recess of the plinth must be at least
50 mm, as measured from the front
surface of the appliance. The space in
front of the plinth must not be obstructed
in any way, so that the air necessary for
the gas to burn can circulate freely.
The following regulations must be taken
into account during assembly and
installation:
• SGWA-Directive G1 - Gas
installations in buildings
• SGWA-Directive L1 - Liquified gas
installations in the household, in
commercial buildings and in the
industry
• Cantonal instances regulations - VKF
fire safety directive "Thermal devices
2015“
1. Slide the oven into its place and align
it with the furniture.
WARNING!
Do not manipulate the
threaded gas
connections.
The screws securing the
gas installation and the
installation itself must
not be touched.
WARNING!
The electrical installation
should be secure and it
cannot pose any risk of
electrical shock.
min. 50
100
480
160
A 759 +0/-1
N 762
105
ENGLISH
5
2. Fix the oven with 2 screws at every
side.
A
3. Open the door to access the gas
installation.
4. Connect the oven to the gas supply.
1.12 Installing burners
1. Remove the screws (1) and (3) from
the transport safeguards on the left
and right side (2) and remove the
transport safeguards.
2. Loosen the four screws (4) next to
the four burners.
1
2
4
3
3
1
2
3
3
CAUTION!
The screws to secure
the horizontal support
are necessary when the
hob is installed with a
wooden surround frame.
3. If necessary, loosen the eight screws
(5) on the two cross bars and lift the
cross bars up. Tighten the screws
again firmly.
5
5
4. Lift the burner unit to the height of the
worktop. Burners on upper corner of
the cooking zones should achieve
the height of the worktop.
5. Slide the unit along the worktop.
Fasten the unit in the cut-out using
the six screws (6) provided. Use
three screws at each side.
66
• In case of a 490 mm deep cut-out,
move the unit forward along the
worktop until it stops.
• In case of a 504 mm cut-out, push
the unit to the end and then move
it back towards yourself by 7 mm.
6. Put the hob back on the cooking
surface and adjust the burners. Make
sure that the hob does not rise above
the surrounding worktop surfaces.
www.electrolux.com6
1.13 Installing the metal burner
plate
1. Place the hob in the cut-out.
2. Secure the hob in place using the 4
screws. Place the screws in the
proper holes and secure them with
spinlock nuts.
3. The 4 burners have to be positioned
in their places without any pressure,
with a very slight pressure towards
the top.
4. Secure the burners into their places
on the burner plate with 2 screws
each.
5. Screw the burner plate to the worktop
with a screw in each side, going
through the oval holes for the pan
support.
The screws have to be screwed in
very tight in order to secure the
connection.
6. Install the burner crowns, burner
caps and the pan support.
Make the final check whether the
appliance functions correctly and the gas
installation is safe.
1.14 Installing the glass burner
plate
A) Installation on top of the
appliance.
1. Trace the dimensions of the hob on
the worktop with a pencil or a water-
soluble felt tip pen. Lift the hob and
put it away.
2. Place the rubber self-adhesive seal
inside the drawn outline,
approximately 2 mm from the edge.
The seal must stick to the surface of
the furniture and there cannot be any
gaps in the outline.
CAUTION!
Do not stretch the seal.
Cut the pieces of the
right size.
3. Put the hob back on the cooking
surface and adjust the burners. Make
sure that the hob does not rise above
the surrounding worktop surfaces.
Make the final check whether the
appliance functions correctly and the gas
installation is safe.
B) Installation onto the worktop
1. Prepare a cut-out in the worktop
according to the dimensions shown
on the pictures 1 and 2. Do not
exceed the tolerance margin.
ENGLISH
7
Picture 1
2. Carefully clean the worktop around
the cut-out and the cut-out edges.
3. The rubber seal (A) has to be glued
onto the surface where the worktop
and the hob touch to prevent
vibrations and protect the glass
against mastic.
Picture 2
A
B
4. Make sure to install the oven and the
burners according to the installation
instructions.
5. Place the glass hob carefully in the
cut-out and then level it making
allowance for the seal around the
edges. As the actual dimensions of
the glass hob and the cutout may
vary, the size of the joint also can be
different by minimum 2 mm.
6. Place the burner cap, burner crown
and the round profile onto burner
base so the ignition candles and
thermocouples extend through their
respective holes. Push the burner
head down firmly until it clicks into its
place correctly.
7. Secure the round profiles, with 2
screws each, onto the burners in the
cooking surface. In this way the hob
is secured to the worktop.
8. Put in place and adjust the burner
crowns and the burner caps. Place
the pan supports in the appropriate
indentations.
Make the final check whether the
appliance functions correctly and the gas
installation is safe.
1.15 Gas burners and diameter of the injectors
Stainless steel hob GKM45CN
Gas type Burner Injector
Mark
1/100 mm
Nomi-
nal
heat
input
kW
Reduced
heat in-
put kW
Gas consumption
m
3
/h
g/h
G30 G31
Natural
gas (2H)
20 mbar
Semi -
rapid
96 2.0 0.45 0.190 - -
Auxiliary 70 1.0 0.33 0.095 - -
Oven 2.7 0.7 0.257 - -
www.electrolux.com8
Gas type Burner Injector
Mark
1/100 mm
Nomi-
nal
heat
input
kW
Reduced
heat in-
put kW
Gas consumption
m
3
/h
g/h
G30 G31
Liquid gas
(3+)
28-30/37
mbar
Semi -
rapid
71 2.0 0.45 - 145 143
Auxiliary 50 1.0 0.33 - 73 71
Oven 80 2.7 0.7 - 196 193
Liquid gas
(3/P/B) 50
mbar
Semi -
rapid
60 2.0 0.45 - 145 143
Auxiliary 43 1.0 0.33 - 73 71
Oven 063 2.6 0.7 - 189 186
Glass hob GKM45GLAS
Gas
type
Burner Injector
Mark
1/100
mm
Nominal
heat in-
put kW
Re-
duced
heat in-
put kW
Gas consumption
m
3
//h
g/h
G30 G31
Natural
gas (2H)
20 mbar
Semi -
rapid
96 1.9 0.45 0.181 - -
Auxiliary 70 1.0 0.33 0.095 - -
Oven 2.7 0.7 0.257 - -
Liquid
gas (3+)
28-30/3
7 mbar
Semi -
rapid
71 1.9 0.45 - 138 136
Auxiliary 50 1.0 0.33 - 73 71
Oven 80 2.7 0.7 - 196 193
Liquid
gas
(3/P/B)
50 mbar
Semi -
rapid
60 1.9 0.45 - 138 136
Auxiliary 43 1.0 0.33 - 73 71
Oven 063 2.6 0.7 - 189 186
1.16 Adjustment to different
types of gas
WARNING!
Let only authorized person
do the adjustment to
different types of gas.
ENGLISH
9
Gas type Regulation Other gas type
G20 20 mbar shut by 1/2 turn G30/G31 28-30/37 mbar
shut G30/G31 50 mbar
G30/G31 28-30/37 mbar shut G30/G31 50 mbar
open by 1/2 turn G20 20 mbar
G30/G31 50 mbar open 1/4 turn G30/G31 28-30/37 mbar
open 3/4 turn G20 20 mbar
1.17 Bypass diameters
BURNER Ø BYPASS 1/100 mm
Semi - rapid 28
Auxiliary 23
Oven 37
2. ENVIRONMENTAL CONCERNS
Recycle the materials with the symbol .
Put the packaging in applicable containers
to recycle it. Help protect the environment
and human health and to recycle waste of
electrical and electronic appliances. Do
not dispose appliances marked with the
symbol with the household waste.
Return the product to your local recycling
facility or contact your municipal office.
*
www.electrolux.com10
ENGLISH
11
electrolux.com/shop
867323329-A-442016
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Electrolux GHL346SW Installation guide
- Category
- Hobs
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Electrolux GHGL4046CN Installation guide
-
Electrolux GHL3046WE Installation guide
-
Electrolux GHL246SW Installation guide
-
Electrolux GK58DKG4O User manual
-
-
-
-
-
-