Electrolux GHL246SW Installation guide

Brand: Electrolux

Model: GHL246SW

Type: Installation guide

Electrolux GHL246SW is a built-in gas hob and oven designed for convenient and efficient cooking. The hob features four burners, including a powerful wok burner, providing flexibility for various cooking techniques. The oven offers multiple cooking functions, including grilling and baking, accommodating a wide range of culinary creations. Its energy-efficient design and safety features ensure an enjoyable cooking experience.

GHL246SW

GHL246WE

EN Information Sheet

CONTENTS

1. INSTALLATION INSTRUCTION.........................................................................2

WE’RE THINKING OF YOU

Thank you for purchasing an Electrolux appliance. You’ve chosen a product that

brings with it decades of professional experience and innovation. Ingenious and

stylish, it has been designed with you in mind. So whenever you use it, you can

be safe in the knowledge that you’ll get great results every time.

Welcome to Electrolux.

Visit our website for:

Get usage advice, brochures, trouble shooter, service information:

www.electrolux.com/webselfservice

www.registerelectrolux.com

Buy Accessories, Consumables and Original spare parts for your appliance:

www.electrolux.com/shop

CUSTOMER CARE AND SERVICE

Always use original spare parts.

When contacting our Authorised Service Centre, ensure that you have the

following data available: Model, PNC, Serial Number.

The information can be found on the rating plate.

Warning / Caution-Safety information

General information and tips

Environmental information

Subject to change without notice.

1. INSTALLATION INSTRUCTION

1.1 General information

• Connection and commissioning of the

gas cooker must be in conformity with

local and national law and regulations.

Only a qualified person must install

the appliance.

• The connection must be confirmed by

a signature of the person installing the

appliance on the warranty card.

• Use only the original connector board

of the built-in appliance.

• During installation and commissioning

the appliance must be disconnected

from the gas supply.

• During any maintenance or repairs

the main gas valve must be closed.

• The general rules applicable to using

gas appliances and the current

directives / instructions concerning the

installation must be strictly obeyed.

1.2 Delivery and packaging

Make sure that the appliance

is in good condition after

transport. Any damage must

be reported immediately and

the appliance should not be

put into service.

www.electrolux.com2

Packaging

• The whole packaging is recyclable.

Check the packaging foil and

styrofoam for the recycling symbols.

• Dispose of the packaging materials

and the appliance, when necessary,

in accordance with the applicable

standards.

• Refer to the local and national

regulations on disposal and read the

labels of the packaging materials.

There is information on sorting the

materials, collection of the used

appliances and proper places of

disposal.

1.3 Hob installation accessories

• 8 screws for fixing the burners grate,

• 2 screws for fixing the hob in place

with the pan support on top with

protective conductor,

• 6 screws to install the hob on the work

surface,

• 8 screws for securing the burners plus

2 spare,

• 2 pan supports.

1.4 Oven installation

accessories

• The chimney for the hot air outlet

placed between the burners,

• Burner caps and crowns for the 4

burners,

• 4 screws for securing the oven in

place.

1.5 Requirements for built-in

Pay special attention during installation

of the back wall of the appliance. After

the installation it will not be easily

accessible, even if there is a distance

between it and the wall.

The furniture where the appliance is

built-in and adjacent to it should be

stable.

The furniture where the appliance is

built-in, the furniture adjacent to it as well

as any synthetic surfaces coatings and

glues near it should be able to safely

withstand the temperatures of at least 95

⁰C.

Any surface coatings and glues not able

to withstand this temperature can cause

deformation of the furniture and

unsticking of the parts near the oven.

Contact the furniture producer in case of

any doubts. This appliance of the third

class is designed to be built-in in kitchen

furniture. The wall behind the appliance

and wall of the piece of furniture next to it

can have any height.

The piece of furniture on the other side

must be on the same level as the hob.

Keep the required minimal distances as

measured in relation to the hob:

• 100 mm on any side to the nearest

piece of furniture,

• 100 mm at the back of the worktop

cut-out to the rear edge of the

worktop,

• 560 mm from the surface of the hob to

the piece of furniture / appliance

above it.

1.6 Flap

The flap is in the lower part of the

appliance.

This is not a storage drawer.

Do not use it as a storage.

Gas connection is installed

under the appliance.

1.7 Gas connection

The gas pipe gasket is in a

bag inside the oven.

Check the factory settings of the

appliance on the rating plate.

The appliance is set for natural gas H 20

mbar.

In case of conversion to different type of

gas, the label should be taken off and

replaced with a new technical label with

the correct data.

The connection to the gas supply should

be permanent.

The appliance should be connected by a

steel-only hose fitted with a safety device

and with a homologation of SGWA

ENGLISH 3

(Swiss Gas and Water Industry

Association).

N 550

A 548 +0/-1

min. 50

A 572

N 600

1. G 1/2" coupler installed at the height

of 160 mm from the ground, to be

installed with at least a flange.

2. Valve to cut off the gas G1/2.

3. Metal tube 50 cm with G1/2 internal

thread, connected to the valve

through a gasket.

160

1. Gas connection

2. Rating plate

Gas protection installation

Install the protection to secure the gas

pipe.

1. Place the metal cover plate over the

pipe.

2. Secure the plate with two screws.

1.8 Build-in gas hob GKM44

Prepare the cut-out in the worktop to

place the hob:

• The cut-out should be placed in the

center of the worktop where the

appliance is installed.

• Make the cut-out in the worktop

according to the dimensions

presented below. Too deep cut-out

must be corrected for example by a

wooden surround.

• Seal the cut surface with an

appropriate heat resistant sealant to

protect it from humidity.

• Preserve the minimal distances:

– 100 mm on any side to the

nearest piece of furniture,

– 100 mm at the back of the

worktop cut-out to the rear edge

of the worktop,

– 560 mm from the surface of the

hob to the piece of furniture /

appliance above it.

www.electrolux.com4

560 1

20-50

490 1

1. The cut-out

2. The table / work surface

3. Front furniture panel

The worktop should surround the hob on

every side.

Adjusting the dimensions in the process

of redecoration / refurbishment.

Cut-outs with dimensions different from

those above have to be adjusted

according to the explanations and

measurements in the tables below.

1. Build-in gas oven with hob 1985 -

1997 without wooden surround

544 (560)

55 (36)

20-50

490 (526)

Cut-out for the hob in a synthetic resin

or stone worktop

Width (mm) Depth (mm)

544 - 560 490

2. Build-in gas oven with hob from

1985 with a wooden surround

ARGH600/58

490

588

542

600

20-50

Cut-out for the hob in a synthetic resin

or stone worktop

Width (mm) Depth (mm)

600 - 542 588 -490

3. Gas cooker built in worktop of

chrome plated stamped steel 1, 2 or 3.

With a wooden surround ARGH600/58

Cut-out for the hob in chrome plated

steel surfaces

Width (mm) Depth (mm)

Should be done in accordance with

separate instructions for cutting out and

installation

1.9 Installing the oven

Make sure that the dimensions marked

with N in the picture of the niche where

the oven is installed are correct and

exact.

The recess of the plinth must be at least

50 mm, as measured from the front

surface of the appliance. The space in

front of the plinth must not be obstructed

in any way, so that the air necessary for

the gas to burn can circulate freely.

The following regulations must be taken

into account during assembly and

installation:

• SGWA-Directive G1 - Gas

installations in buildings

• SGWA-Directive L1 - Liquified gas

installations in the household, in

ENGLISH 5

commercial buildings and in the

industry

• Cantonal instances regulations - VKF

fire safety directive "Thermal devices

2015“

1. Slide the oven into its place and align

it with the furniture.

WARNING!

Do not manipulate the

threaded gas connections.

The screws securing the gas

installation and the

installation itself must not be

touched.

min. 50

100

480

160

A 759 +0/-1

N 762

105

2. Fix the oven with 2 screws at every

side.

3. Open the door to access the gas

installation.

4. Connect the oven to the gas supply.

1.10 Chimney over the steam

outlet

In case of stone worktops, the supports

have to be glued in the cut-out by means

of a special glue for stone.

The chimney (2) is installed over the hot

air outlet and fixed with 1 screw (3).

Adjust the height of the chimney so that

the two flaps rest on the worktop and fix

it with the screw (3)

1.11 Installing burners

1. Remove the screws (1) and (3) from

the transport safeguards on the left

and right side (2) and remove the

transport safeguards.

2. Loosen the four screws (4) next to

the four burners.

CAUTION!

The screws to secure

the horizontal support

are necessary when the

hob is installed with a

wooden surround frame.

3. If necessary, loosen the eight screws

(5) on the two cross bars and lift the

cross bars up. Tighten the screws

again firmly.

www.electrolux.com6

4. Lift the burner unit to the height of the

worktop. Burners on upper corner of

the cooking zones should achieve

the height of the worktop.

5. Slide the unit along the worktop.

Fasten the unit in the cut-out using

the six screws (6) provided. Use

three screws at each side.

• In case of a 490 mm deep cut-out,

move the unit forward along the

worktop until it stops.

• In case of a 504 mm cut-out, push

the unit to the end and then move

it back towards yourself by 7 mm.

6. Put the hob back on the cooking

surface and adjust the burners. Make

sure that the hob does not rise above

the surrounding worktop surfaces.

1.12 Installing the metal burner

plate

1. Place the hob in the cut-out.

2. Secure the hob in place using the 6

screws. Place the screws in the

proper holes and secure them with

spinlock nuts.

3. The 4 burners have to be positioned

in their places without any pressure,

with a very slight pressure towards

the top.

4. Secure the burners into their places

on the burner plate with 2 screws

each.

5. Screw the burner plate to the worktop

with a screw in each side, going

through the oval holes for the pan

support.

The screws have to be screwed in

very tight in order to secure the

connection.

6. Install the burner crowns, burner

caps and the pan support.

Make the final check whether the

appliance functions correctly and the gas

installation is safe.

ENGLISH 7

1.13 Gas burners and diameter of the injectors

Stainless steel hob GKM44CN

Gas type Burner Injector

Mark

1/100 mm

Nomi‐

nal

heat

input

Reduced

heat in‐

put kW

Gas consumption

g/h

G30 G31

Natural

gas (2H)

20 mbar

Semi -

rapid

96 2.0 0.45 0.190 - -

Auxili‐

ary

70 1.0 0.33 0.095 - -

Oven 2.7 0.7 0.257 - -

Liquid gas

(3+)

28-30/37

mbar

Semi -

rapid

71 2.0 0.45 - 145 143

Auxili‐

ary

50 1.0 0.33 - 73 71

Oven 80 2.7 0.7 - 196 193

Liquid gas

(3/P/B) 50

mbar

Semi -

rapid

60 2.0 0.45 - 145 143

Auxili‐

ary

43 1.0 0.33 - 73 71

Oven 063 2.6 0.7 - 189 186

1.14 Adjustment to different

types of gas

WARNING!

Let only authorized person

do the adjustment to

different types of gas.

Gas type Regulation Other gas type

G20 20 mbar shut by 1/2 turn G30/G31 28-30/37 mbar

shut G30/G31 50 mbar

G30/G31 28-30/37 mbar shut G30/G31 50 mbar

open by 1/2 turn G20 20 mbar

G30/G31 50 mbar open 1/4 turn G30/G31 28-30/37 mbar

open 3/4 turn G20 20 mbar

www.electrolux.com8

1.15 Bypass diameters

BURNER Ø BYPASS 1/100 mm

Semi - rapid 28

Auxiliary 23

Oven 37

2. ENVIRONMENTAL CONCERNS

Recycle the materials with the symbol

. Put the packaging in applicable

containers to recycle it. Help protect the

environment and human health and to

recycle waste of electrical and electronic

appliances. Do not dispose appliances

marked with the symbol with the

household waste. Return the product to

your local recycling facility or contact

your municipal office.

ENGLISH 9

www.electrolux.com10

ENGLISH 11

www.electrolux.com/shop

867323331-B-152016

Electrolux GHL246SW Installation guide

Electrolux GHL246SW Installation guide

Electrolux GHL246SW Installation guide

Related papers

Other documents