Electrolux GHGL4046CN Installation guide

Brand: Electrolux

Model: GHGL4046CN

Category: Hobs

Type: Installation guide

Electrolux GHGL4046CN gas hob offers precise flame control for perfect cooking results. Its four gas burners, including a powerful wok burner, provide versatility for various cooking techniques. The sleek glass surface and cast iron pan supports ensure easy cleaning and stability for your cookware. Experience efficient and enjoyable cooking with Electrolux GHGL4046CN.

EN Installation Instructions

1. INSTALLATION INSTRUCTIONS

1.1 General information

• Connection and commissioning of the

gas cooker must be in conformity with

local and national law and regulations.

Only a qualified person must install

the appliance.

• The connection must be confirmed by

a signature of the person installing the

appliance on the warranty card.

• Use only the original connector board

of the built-in appliance.

• During installation and commissioning

the appliance must be disconnected

from the gas and electrical supply.

• During any maintenance or repairs

the main gas valve must be closed

and the appliance must be unplugged

from the power supply or the fuses

must be released, depending on the

connection.

• The general rules applicable to using

gas appliances and electrical

appliances and the current directives /

instructions concerning the installation

must be strictly obeyed.

1.2 Delivery and packaging

Make sure that the appliance

is in good condition after

transport. Any damage must

be reported immediately and

the appliance should not be

put into service.

Packaging

• The whole packaging is recyclable.

Check the packaging foil and

styrofoam for the recycling symbols.

• Dispose of the packaging materials

and the appliance, when necessary,

in accordance with the applicable

standards.

• Refer to the local and national

regulations on disposal and read the

labels of the packaging materials.

There is information on sorting the

materials, collection of the used

appliances and proper places of

disposal.

1.3 Hob installation accessories

• 8 screws for fixing the burners grate,

• 2 screws for fixing the hob in place

with the pan support on top with

protective conductor,

• 4 screws to install the hob on the work

surface,

• 8 screws for securing the burners plus

2 spare,

• 2 pan supports.

1.4 Glass plate installation

accessories

• Seal,

• 8 screws for the plywood panel 3.5 x

25 to secure the burner,

• 4 enamelled joints for the burner,

• 4 rubber gaskets,

• 8 screws 2.9 x 13 for securing the

burners on the hob plus 2 spare,

• 2 pan supports.

1.5 Oven installation accessories

• Burner caps and crowns for the 4

burners,

• 4 screws for securing the oven in

place.

1.6 Requirements for built-in

Make sure that during installation the

appliance is disconnected from the power

supply and take precautions against

possible ignition.

Pay special attention during installation of

the back wall of the appliance. After the

installation it will not be easily accessible,

even if there is a distance between it and

the wall.

The furniture where the appliance is built-

in and adjacent to it should be stable.

The furniture where the appliance is built-

in, the furniture adjacent to it as well as

any synthetic surfaces coatings and glues

near it should be able to safely withstand

the temperatures of at least 95 ⁰C.

Any surface coatings and glues not able to

withstand this temperature can cause

deformation of the furniture and unsticking

www.electrolux.com2

of the parts near the oven. Contact the

furniture producer in case of any doubts.

This appliance of the third class is

designed to be built-in in kitchen furniture.

The wall behind the appliance and wall of

the piece of furniture next to it can have

any height.

The piece of furniture on the other side

must be on the same level as the hob.

Keep the required minimal distances as

measured in relation to the hob:

• 100 mm on any side to the nearest

piece of furniture,

• 100 mm at the back of the worktop

cut-out to the rear edge of the

worktop,

• 560 mm from the surface of the hob to

the piece of furniture / appliance

above it.

1.7 Gas connection

The gas pipe gasket is in a

bag inside the oven.

Check the factory settings of the

appliance on the rating plate.

The appliance is set for natural gas H 20

mbar.

In case of conversion to different type of

gas, the label should be taken off and

replaced with a new technical label with

the correct data.

The connection to the gas supply should

be permanent.

The appliance should be connected by a

steel-only hose fitted with a safety device

and with a homologation of SGWA (Swiss

Gas and Water Industry Association).

100

A min. 550

B 565

C 600

x = 20

A 594 +0/-1

N 600

1. Cut-out at the bottom to carry out all

the installation works without

difficulties

460

20-50 R

2. G 1/2" coupler installed at the

bottom, to be installed with at least a

flange.

3. Valve to cut off the gas G1/2.

4. Metal tube 150 cm with G1/2 internal

thread, connected to the valve

through a gasket.

Gas protection installation

Install the protection to secure the gas

pipe.

1. Place the metal cover plate over the

pipe.

ENGLISH

2. Secure the plate with two screws.

1.8 Electrical connection

Standard socket, type 13.

The electrical installation must have an

isolation device which lets you disconnect

the appliance from the main power supply

at all poles. The isolation device must have

a contact opening width of minimum 3

mm.

Use only correct isolation devices: line

protecting cut-outs, fuses, earth leakage

trips and contactors. Screw type fuses

must be removed from the holder.

Before the connection make sure that the

voltage on the rating plate, nominal

voltage of the oven, agrees with the power

supply. The rating plate can be found on

the frame of the appliance, open the door

to access it.

The voltage of the heaters is 230 V AC,

but the appliance can also function

correctly on the 220 V AC.

The electrical cable cannot touch the back

wall of the built-in appliance.

The socket must be easily accessible.

1. Gas connection

2. Rating plate

1.9 Build-in gas hob

GKM45GLAS and GKM45CN

Prepare the cut-out in the worktop to

place the hob:

• The cut-out should be placed in the

center of the worktop where the

appliance is installed.

• Make the cut-out in the worktop

according to the dimensions

presented below. Too deep cut-out

must be corrected for example by a

wooden surround.

• Seal the cut surface with an

appropriate heat resistant sealant to

protect it from humidity.

• Preserve the minimal distances:

– 100 mm on any side to the

nearest piece of furniture,

– 100 mm at the back of the

worktop cut-out to the rear edge

of the worktop,

– 560 mm from the surface of the

hob to the piece of furniture /

appliance above it.

www.electrolux.com4

560 1

20-50

490 1

1. The cut-out

2. The table / work surface

3. Front furniture panel

The worktop should surround the hob on

every side.

Adjusting the dimensions in the process of

redecoration / refurbishment.

Cut-outs with dimensions different from

those above have to be adjusted

according to the explanations and

measurements in the tables below.

1. Build-in gas oven with hob 1985 - 1997

without wooden surround

544 (560)

55 (36)

20-50

490 (526)

Cut-out for the hob in a synthetic resin or

stone worktop

Width (mm) Depth (mm)

544 - 560 490

2. Build-in gas oven with hob from 1985

with a wooden surround ARGH600/58

490

588

542

600

20-50

Cut-out for the hob in a synthetic resin or

stone worktop

Width (mm) Depth (mm)

600 - 542 588 -490

3. Gas cooker built in worktop of chrome

plated stamped steel 1, 2 or 3. With a

wooden surround ARGH600/58

Cut-out for the hob in chrome plated

steel surfaces

Width (mm) Depth (mm)

Should be done in accordance with sep-

arate instructions for cutting out and in-

stallation

1.10 Installing the oven

Make sure that the dimensions of the

niche where the oven is installed and the

dimensions of the cut-out at the bottom

are correct and exact.

The following regulations must be taken

into account during assembly and

installation:

• SGWA-Directive G1 - Gas

installations in buildings

• SGWA-Directive L1 - Liquified gas

installations in the household, in

commercial buildings and in the

industry

• Cantonal instances regulations - VKF

fire safety directive "Thermal devices

2015“ Gas directive of the SSIGE G1

1. Remove or open the flap at the lower

part of the oven to access the space

where the connection will be made.

ENGLISH

2. Place the oven in front of the niche

where it will be installed.

3. Secure the gas hose to the

appliance. The connection should be

gas tight and secured with a thread,

for example hemp rope.

WARNING!

The electrical installation

should be secure and it

cannot pose any risk of

electrical shock. The

screws securing the gas

installation and the

installation itself must

not be touched.

A 595 +0/-1

N 600

1. Gas pipe

2. Electrical cable

3. Gas valve

4. Gas connection

5. Electrical connection

6. Front flap

4. Slide the oven into its place until its

front is aligned with the fronts of the

surrounding furniture panels. Secure

the appliance at the two sides with

two screws.

Make sure that the gas hose does not

become crushed or bent in any way

during the installation.

1.11 Installing burners

1. Remove the screws (1) and (3) from

the transport safeguards on the left

and right side (2) and remove the

transport safeguards.

2. Loosen the four screws (4) next to

the four burners.

CAUTION!

The screws to secure

the horizontal support

are necessary when the

hob is installed with a

wooden surround frame.

3. If necessary, loosen the eight screws

(5) on the two cross bars and lift the

cross bars up. Tighten the screws

again firmly.

4. Lift the burner unit to the height of the

worktop. Burners on upper corner of

the cooking zones should achieve

the height of the worktop.

www.electrolux.com6

5. Slide the unit along the worktop.

Fasten the unit in the cut-out using

the six screws (6) provided. Use

three screws at each side.

• In case of a 490 mm deep cut-out,

move the unit forward along the

worktop until it stops.

• In case of a 504 mm cut-out, push

the unit to the end and then move

it back towards yourself by 7 mm.

6. Put the hob back on the cooking

surface and adjust the burners. Make

sure that the hob does not rise above

the surrounding worktop surfaces.

1.12 Installing the metal burner

plate

1. Place the hob in the cut-out.

2. Secure the hob in place using the 4

screws. Place the screws in the

proper holes and secure them with

spinlock nuts.

3. The 4 burners have to be positioned

in their places without any pressure,

with a very slight pressure towards

the top.

4. Secure the burners into their places

on the burner plate with 2 screws

each.

5. Screw the burner plate to the worktop

with a screw in each side, going

through the oval holes for the pan

support.

The screws have to be screwed in

very tight in order to secure the

connection.

6. Install the burner crowns, burner

caps and the pan support.

Make the final check whether the

appliance functions correctly and the gas

installation is safe.

1.13 Installing the glass burner

plate

A) Installation on top of the

appliance.

1. Trace the dimensions of the hob on

the worktop with a pencil or a water-

soluble felt tip pen. Lift the hob and

put it away.

2. Place the rubber self-adhesive seal

inside the drawn outline,

approximately 2 mm from the edge.

The seal must stick to the surface of

the furniture and there cannot be any

gaps in the outline.

ENGLISH

CAUTION!

Do not stretch the seal.

Cut the pieces of the

right size.

3. Put the hob back on the cooking

surface and adjust the burners. Make

sure that the hob does not rise above

the surrounding worktop surfaces.

Make the final check whether the

appliance functions correctly and the gas

installation is safe.

B) Installation onto the worktop

1. Prepare a cut-out in the worktop

according to the dimensions shown

on the pictures 1 and 2. Do not

exceed the tolerance margin.

Picture 1

2. Carefully clean the worktop around

the cut-out and the cut-out edges.

3. The rubber seal (A) has to be glued

onto the surface where the worktop

and the hob touch to prevent

vibrations and protect the glass

against mastic.

Picture 2

4. Make sure to install the oven and the

burners according to the installation

instructions.

5. Place the glass hob carefully in the

cut-out and then level it making

allowance for the seal around the

edges. As the actual dimensions of

the glass hob and the cutout may

vary, the size of the joint also can be

different by minimum 2 mm.

6. Place the burner cap, burner crown

and the round profile onto burner

base so the ignition candles and

thermocouples extend through their

respective holes. Push the burner

head down firmly until it clicks into its

place correctly.

7. Secure the round profiles, with 2

screws each, onto the burners in the

cooking surface. In this way the hob

is secured to the worktop.

8. Put in place and adjust the burner

crowns and the burner caps. Place

the pan supports in the appropriate

indentations.

Make the final check whether the

appliance functions correctly and the gas

installation is safe.

www.electrolux.com8

1.14 Gas burners and diameter of the injectors

Stainless steel hob GKM45CN

Gas type Burner Injector

Mark

1/100 mm

Nomi-

nal

heat

input

Reduced

heat in-

put kW

Gas consumption

g/h

G30 G31

Natural

gas (2H)

20 mbar

Semi -

rapid

96 2.0 0.45 0.190 - -

Auxiliary 70 1.0 0.33 0.095 - -

Oven 2.7 0.7 0.257 - -

Liquid gas

(3+)

28-30/37

mbar

Semi -

rapid

71 2.0 0.45 - 145 143

Auxiliary 50 1.0 0.33 - 73 71

Oven 80 2.7 0.7 - 196 193

Liquid gas

(3/P/B) 50

mbar

Semi -

rapid

60 2.0 0.45 - 145 143

Auxiliary 43 1.0 0.33 - 73 71

Oven 063 2.6 0.7 - 189 186

Glass hob GKM45GLAS

Gas

type

Burner Injector

Mark

1/100

Nominal

heat in-

put kW

Re-

duced

heat in-

put kW

Gas consumption

//h

g/h

G30 G31

Natural

gas (2H)

20 mbar

Semi -

rapid

96 1.9 0.45 0.181 - -

Auxiliary 70 1.0 0.33 0.095 - -

Oven 2.7 0.7 0.257 - -

Liquid

gas (3+)

28-30/3

7 mbar

Semi -

rapid

71 1.9 0.45 - 138 136

Auxiliary 50 1.0 0.33 - 73 71

Oven 80 2.7 0.7 - 196 193

Liquid

gas

(3/P/B)

50 mbar

Semi -

rapid

60 1.9 0.45 - 138 136

Auxiliary 43 1.0 0.33 - 73 71

Oven 063 2.6 0.7 - 189 186

ENGLISH

1.15 Adjustment to different

types of gas

WARNING!

Let only authorized person

do the adjustment to

different types of gas.

Gas type Regulation Other gas type

G20 20 mbar shut by 1/2 turn G30/G31 28-30/37 mbar

shut G30/G31 50 mbar

G30/G31 28-30/37 mbar shut G30/G31 50 mbar

open by 1/2 turn G20 20 mbar

G30/G31 50 mbar open 1/4 turn G30/G31 28-30/37 mbar

open 3/4 turn G20 20 mbar

1.16 Bypass diameters

BURNER Ø BYPASS 1/100 mm

Semi - rapid 28

Auxiliary 23

Oven 37

2. ENVIRONMENTAL CONCERNS

Recycle the materials with the symbol .

Put the packaging in applicable containers

to recycle it. Help protect the environment

and human health and to recycle waste of

electrical and electronic appliances. Do

not dispose appliances marked with the

symbol with the household waste.

Return the product to your local recycling

facility or contact your municipal office.

www.electrolux.com10

ENGLISH

www.electrolux.com/shop

867323330-A-442016

Electrolux GHGL4046CN Installation guide

Brand: Electrolux

Model: GHGL4046CN

Category: Hobs

Type: Installation guide

Download PDF

report

Electrolux GHGL4046CN Installation guide

Electrolux GHGL4046CN Installation guide

Related papers

Other documents