DECAL PLACEMENT
9
Semi Gloss Black
Gloss Red
Gloss Red Metallic
Aluminum
Silver
Transparent Blue
Transparent Red
This paint guide is provided to complete this kit
as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
Noir satiné
Rouge brillant
Rouge brillant métallisé
Aluminium
Argent
Bleu transparent
Rouge transparent
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before
cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
DECAL APPLICATION INSTRUCTIONS
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
NOTE: Decals are compatible with
setting solutions or solvents.
READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente peu
concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
'69 DODGE CHARGER
NHRA® FUNNY CAR
KIT 4286 85428610200
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85428610200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.
Kit 4286 - Page 8
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER
* A COLLER
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* DO NOT CEMENT
* NE PAS COLLER
* DECAL
* DECAL COMANIE
* ASSEMBLY CAUTION
*ATTENTION D ASSEMBLEE
* OPTIONAL PARTS
* PIECES EN OPTION
* REPEAT PROCEDURE
* REPETEZ LE PROCEDE
`` ` ` `
The Chi-Town Hustler was one of the
top winning and most popular funny
cars of the late 60's and early 70's. This
famous 1969 Dodge Charger funny car
belonged to the team of Farkonas,
Coil, and Minick. With Pat Minick as
driver the awesome mini Charger
did spectacular 1/8 quarter mile burn
outs and has posted a top quarter
mile time of 6.7 seconds at 220 mph.
Your Revell model features a highly
detailed supercharged 426 cubic inch
Chrysler HEMI® engine, an accurate
Mini Dodge Charger body that lifts to
show the custom made offset Farkonas
designed chassis and authentic vin-
tage Chi-Town Hustler drag graphics.
ENGINE ASSEMBLY
1BODY ASSEMBLY
7
REAR / FINAL ASSEMBLY
8
51
RIGHT
ENGINE
HALF
ALUMINUM
50
LEFT
ENGINE
HALF
ALUMINUM
★56
TRANSMISSION PAN
CHROME
★43
CHUTE PLATE
CHROME
SILVER
BUMPER
SILVER
BUMPER
★24
LEFT
REAR SPOILER
CHROME
★71
RIGHT
REAR SPOILER
CHROME
★64
SUPER CHARGER
REAR
CHROME
69
BELT TENSIONER
ALUMINUM
★62
SUPER CHARGER
BODY
CHROME
★63
SUPER CHARGER
FRONT
CHROME
68
INJECTORS
ALUMINUM
60
FUEL PUMP
ALUMINUM
65
ENGINE BELT
SEMI GLOSS BLACK
(ALUMINUM
PULLEYS)
52
ENGINE FRONT
ALUMINUM
70
OIL LINE
SEMI GLOSS
BLACK
3
FRAME
GLOSS RED
58
LEFT
EXHAUST HEADER
ALUMINUM
57
RIGHT
EXHAUST HEADER
ALUMINUM
61
STARTER
SEMI GLOSS
BLACK
75
OIL FILTER
SEMI GLOSS
BLACK
★67
RIGHT
ROCKER COVER
CHROME
★66
LEFT
ROCKER COVER
CHROME
44
CHUTE
SEMI GLOSS
BLACK
44
CHUTE
SEMI GLOSS
BLACK
34
DECAL
13
DECAL
33
DISPLAY SUPPORT
SEMI GLOSS
BLACK
54
INTAKE MANIFOLD
ALUMINUM
53
CYLINDER
HEAD
ALUMINUM 53
CYLINDER
HEAD
ALUMINUM
55
OIL PAN
ALUMINUM
Kit 4286 - Page 2 Kit 4286 - Page 7
FRONT VIEW SHOWING ANGLE
OF EXHAUST
CUT-A-WAY SHOWING
THE PIVOT BRACKETS
16
COCKPIT SHROUD
ALUMINUM
78
COCKPIT
FRONT PANEL
ALUMINUM
81
FRONT BULKHEAD
SEMI GLOSS BLACK
FRONT RIB
1
BODY
GLOSS RED METALLIC
SEMI GLOSS BLACK
(INSIDE)
80
PIVOT BRACKETS
ALUMINUM
BULKHEAD GOES
IN FRONT OF THE
FRONT RIB
WHEEL ASSEMBLY
5
WINDOWS ASSEMBLY
6
REAR SUSPENSION ASSEMBLY
2
Kit 4286 - Page 3
Kit 4286 - Page 6
30
REAR AXLE
FRONT
GLOSS RED
31
REAR AXLE
BACK
GLOSS RED
35
RIGHT REAR
DISC BRAKE
ALUMINUM
34
LEFT REAR
DISC BRAKE
ALUMINUM
27
RIGHT REAR
TRAILING ARM
GLOSS RED
28
LEFT REAR
TRAILING ARM
GLOSS RED
★32
REAR AXLE
COVER
CHROME
★76
WHEELIE BARS
CHROME
★77
WHEELIE BAR
CROSS MEMBER
CHROME
★38
REAR
OUTER WHEEL
CHROME
★42
AXLE CAP
CHROME
★42
AXLE CAP
CHROME
★36
FRONT
OUTER WHEEL
CHROME
★37
FRONT
INNER WHEEL
CHROME ★79
REAR
INNER WHEEL
CHROME
DRAG SLICK
FRIONT TIRE
METAL AXLE
29
REAR AXLE
CROSS MEMBER
GLOSS RED
95
REAR SHOCK
GLOSS RED
SEMI GLOSS
BLACK
SEMI
GLOSS
BLACK
GLOSS
RED
GLOSS
RED
95
REAR SHOCK
GLOSS RED
59
DRIVESHAFT
SEMI GLOSS BLACK
ROTATE TIRES ON A PIECE OF SAND
PAPER TO REMOVE SEAM AND GIVE A
MORE REALISTIC APPERANCE
90
WINDSHIELD
CLEAR
92
RIGHT
SIDE WINDOW
CLEAR
93
LEFT
SIDE WINDOW
CLEAR
47
FRONT SPOILER
GLOSS RED METALLIC
2
HOOD
GLOSS RED METALLIC
(SEMI GLOSS BLACK INSIDE)
91
REAR WINDOW
CLEAR
FIRST
SECOND
FRONT SUSPENSION ASSEMBLY
3COCKPIT / STEERING ASSEMBLY
4
Kit 4286 - Page 4 Kit 4286 - Page 5
10
FRAME FRONT
CROSS MEMBER
GLOSS RED
21
ROLL CAGE
REAR
SEMI GLOSS BLACK
20
ROLL CAGE
FRONT
SEMI GLOSS BLACK
96
LEFT
ROLL CAGE SIDE
SEMI GLOSS BLACK
22
STEERING COLUMN
SUPPORT
GLOSS RED
18
COCKPIT
FRONT WALL
ALUMINUM
97
RIGHT
ROLL CAGE SIDE
SEMI GLOSS BLACK
★9
LEFT FRONT
TRAILING ARM
CHROME
★8
RIGHT FRONT
TRAILING ARM
CHROME
★4
FRONT AXLE
CHROME
★6
TIE ROD
CHROME
★5
FRONT SHOCKS
CHROME
★13
FUEL TANK
REAR
CHROME
★12
FUEL TANK
FRONT
CHROME
★14
FUEL TANK
TOP
CHROME
★39
WATER TANK
TOP
CHROME
★23
STEERING COLUMN
CHROME
★26
STEERING WHEEL
CHROME
★25
SHIFT LEVER
CHROME
17
COCKPIT BUCKET
ALUMINUM BUCKET
(BELT BUCKLES SILVER)
(SEAT SEMI GLOSS
BLACK)
SEMI GLOSS BLACK
(RIM)
★40
WATER TANK
BOTTOM
CHROME
★73
WATER TANK
SUPPORT
CHROME
★7
STEERING LINKAGE
CHROME
CUT-A-WAY SHOWING
HOLE FOR COLUMN
FUEL TANK
WATER TANK
FRONT SUSPENSION ASSEMBLY
3COCKPIT / STEERING ASSEMBLY
4
Kit 4286 - Page 4 Kit 4286 - Page 5
10
FRAME FRONT
CROSS MEMBER
GLOSS RED
21
ROLL CAGE
REAR
SEMI GLOSS BLACK
20
ROLL CAGE
FRONT
SEMI GLOSS BLACK
96
LEFT
ROLL CAGE SIDE
SEMI GLOSS BLACK
22
STEERING COLUMN
SUPPORT
GLOSS RED
18
COCKPIT
FRONT WALL
ALUMINUM
97
RIGHT
ROLL CAGE SIDE
SEMI GLOSS BLACK
★9
LEFT FRONT
TRAILING ARM
CHROME
★8
RIGHT FRONT
TRAILING ARM
CHROME
★4
FRONT AXLE
CHROME
★6
TIE ROD
CHROME
★5
FRONT SHOCKS
CHROME
★13
FUEL TANK
REAR
CHROME
★12
FUEL TANK
FRONT
CHROME
★14
FUEL TANK
TOP
CHROME
★39
WATER TANK
TOP
CHROME
★23
STEERING COLUMN
CHROME
★26
STEERING WHEEL
CHROME
★25
SHIFT LEVER
CHROME
17
COCKPIT BUCKET
ALUMINUM BUCKET
(BELT BUCKLES SILVER)
(SEAT SEMI GLOSS
BLACK)
SEMI GLOSS BLACK
(RIM)
★40
WATER TANK
BOTTOM
CHROME
★73
WATER TANK
SUPPORT
CHROME
★7
STEERING LINKAGE
CHROME
CUT-A-WAY SHOWING
HOLE FOR COLUMN
FUEL TANK
WATER TANK
WHEEL ASSEMBLY
5
WINDOWS ASSEMBLY
6
REAR SUSPENSION ASSEMBLY
2
Kit 4286 - Page 3Kit 4286 - Page 6
30
REAR AXLE
FRONT
GLOSS RED
31
REAR AXLE
BACK
GLOSS RED
35
RIGHT REAR
DISC BRAKE
ALUMINUM
34
LEFT REAR
DISC BRAKE
ALUMINUM
27
RIGHT REAR
TRAILING ARM
GLOSS RED
28
LEFT REAR
TRAILING ARM
GLOSS RED
★32
REAR AXLE
COVER
CHROME
★76
WHEELIE BARS
CHROME
★77
WHEELIE BAR
CROSS MEMBER
CHROME
★38
REAR
OUTER WHEEL
CHROME
★42
AXLE CAP
CHROME
★42
AXLE CAP
CHROME
★36
FRONT
OUTER WHEEL
CHROME
★37
FRONT
INNER WHEEL
CHROME ★79
REAR
INNER WHEEL
CHROME
DRAG SLICK
FRIONT TIRE
METAL AXLE
29
REAR AXLE
CROSS MEMBER
GLOSS RED
95
REAR SHOCK
GLOSS RED
SEMI GLOSS
BLACK
SEMI
GLOSS
BLACK
GLOSS
RED
GLOSS
RED
95
REAR SHOCK
GLOSS RED
59
DRIVESHAFT
SEMI GLOSS BLACK
ROTATE TIRES ON A PIECE OF SAND
PAPER TO REMOVE SEAM AND GIVE A
MORE REALISTIC APPERANCE
90
WINDSHIELD
CLEAR
92
RIGHT
SIDE WINDOW
CLEAR
93
LEFT
SIDE WINDOW
CLEAR
47
FRONT SPOILER
GLOSS RED METALLIC
2
HOOD
GLOSS RED METALLIC
(SEMI GLOSS BLACK INSIDE)
91
REAR WINDOW
CLEAR
FIRST
SECOND
ENGINE ASSEMBLY
1
BODY ASSEMBLY
7
REAR / FINAL ASSEMBLY
8
51
RIGHT
ENGINE
HALF
ALUMINUM
50
LEFT
ENGINE
HALF
ALUMINUM
★56
TRANSMISSION PAN
CHROME
★43
CHUTE PLATE
CHROME
SILVER
BUMPER
SILVER
BUMPER
★24
LEFT
REAR SPOILER
CHROME
★71
RIGHT
REAR SPOILER
CHROME
★64
SUPER CHARGER
REAR
CHROME
69
BELT TENSIONER
ALUMINUM
★62
SUPER CHARGER
BODY
CHROME
★63
SUPER CHARGER
FRONT
CHROME
68
INJECTORS
ALUMINUM
60
FUEL PUMP
ALUMINUM
65
ENGINE BELT
SEMI GLOSS BLACK
(ALUMINUM
PULLEYS)
52
ENGINE FRONT
ALUMINUM
70
OIL LINE
SEMI GLOSS
BLACK
3
FRAME
GLOSS RED
58
LEFT
EXHAUST HEADER
ALUMINUM
57
RIGHT
EXHAUST HEADER
ALUMINUM
61
STARTER
SEMI GLOSS
BLACK
75
OIL FILTER
SEMI GLOSS
BLACK
★67
RIGHT
ROCKER COVER
CHROME
★66
LEFT
ROCKER COVER
CHROME
44
CHUTE
SEMI GLOSS
BLACK
44
CHUTE
SEMI GLOSS
BLACK
34
DECAL
13
DECAL
33
DISPLAY SUPPORT
SEMI GLOSS
BLACK
54
INTAKE MANIFOLD
ALUMINUM
53
CYLINDER
HEAD
ALUMINUM 53
CYLINDER
HEAD
ALUMINUM
55
OIL PAN
ALUMINUM
Kit 4286 - Page 2
Kit 4286 - Page 7
FRONT VIEW SHOWING ANGLE
OF EXHAUST
CUT-A-WAY SHOWING
THE PIVOT BRACKETS
16
COCKPIT SHROUD
ALUMINUM
78
COCKPIT
FRONT PANEL
ALUMINUM
81
FRONT BULKHEAD
SEMI GLOSS BLACK
FRONT RIB
1
BODY
GLOSS RED METALLIC
SEMI GLOSS BLACK
(INSIDE)
80
PIVOT BRACKETS
ALUMINUM
BULKHEAD GOES
IN FRONT OF THE
FRONT RIB
DECAL PLACEMENT
9
Semi Gloss Black
Gloss Red
Gloss Red Metallic
Aluminum
Silver
Transparent Blue
Transparent Red
This paint guide is provided to complete this kit
as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
Noir satiné
Rouge brillant
Rouge brillant métallisé
Aluminium
Argent
Bleu transparent
Rouge transparent
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before
cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
DECAL APPLICATION INSTRUCTIONS
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
NOTE: Decals are compatible with
setting solutions or solvents.
READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente peu
concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
'69 DODGE CHARGER
NHRA® FUNNY CAR
KIT 4286 85428610200
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85428610200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.
Kit 4286 - Page 8
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER
* A COLLER
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* DO NOT CEMENT
* NE PAS COLLER
* DECAL
* DECAL COMANIE
* ASSEMBLY CAUTION
*ATTENTION D ASSEMBLEE
* OPTIONAL PARTS
* PIECES EN OPTION
* REPEAT PROCEDURE
* REPETEZ LE PROCEDE
`` ` ` `
The Chi-Town Hustler was one of the
top winning and most popular funny
cars of the late 60's and early 70's. This
famous 1969 Dodge Charger funny car
belonged to the team of Farkonas,
Coil, and Minick. With Pat Minick as
driver the awesome mini Charger
did spectacular 1/8 quarter mile burn
outs and has posted a top quarter
mile time of 6.7 seconds at 220 mph.
Your Revell model features a highly
detailed supercharged 426 cubic inch
Chrysler HEMI® engine, an accurate
Mini Dodge Charger body that lifts to
show the custom made offset Farkonas
designed chassis and authentic vin-
tage Chi-Town Hustler drag graphics.
/