DMX Power Supply 3 x 96 watt - Installation Instructions
Models PSDMX-3X96-24
Please read all instructions prior to installation and keep for future reference!
This class 2 power supply is to be installed by a qualified electrician in accordance with the National Electrical
Code (NEC) and local building codes. The power supply must be installed in a well ventilated area and free from
explosive gases and vapors. Proper operation requires the free flow of air. Power supply is well suited for LED or
resistive loads at or below their maximum output rating per circuit. Suitable For Damp Location.
WARNING! Risk of Fire or Electric Shock, Do Not Interconnect Output Terminal.
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV1.3
0 519 2 0 2 3
1 / 3
PLENUM FOR
SUCH USE IN
ACCORDANCE
WITH UL2043
Models PSDMX-3X96-24
A. Height 13.00”
B. Width 6.60”
C. Depth 4.20”
MAX Load 3 x 96 Watts
3
4
Before installing, check the label and ensure the power supply has the proper input
voltage, output voltage, and wattage for the job. Check the wire markings to ensure
they match the wiring diagram below. Refer to table above for the maximum loads
supported by each power supply.
It is recommended that the power supply be
mounted vertically & mount a minimum of
12” above ground level or deck, 24” below
ceiling, and allow 4” of clearance around
power supply (excluding the mounting side)
to provide for proper air circulation. Use
the provided hardware to mount properly
to wall.
Remove the wiring compartment cover and knockouts on both ends of
the power supply to connect.
12” MIN
use Luminii voltage drop calculator (http://www.luminii.com/voltage-drop-
calculator) to calculate wire gage for low-voltage connection
1
2
24” MIN
power supply
power supply
screw &
anchor
120-277VAC wiring
compartment
120-277VAC
wiring compartment
cover
screw
power supply
24VDC wiring
compartment
cover
Connect the white (neutral) and black (hot) power supply wires to the white and
black power wires ( 120 - 277 VAC ). Followed by connecting the ground wires
in accordance with local electrical codes.
Reference wiring diagrams on page 2. Feed wire into the terminal block
hole by intserting a small flat-head screwdriver into the terminal block slot
and push down, thus opening the terminal block hole. Then, insert the
wire lead and release the screwdriver to secre wire in place.
Secure compartment cover
back onto the power supply.
5
solid or stranded : 28 - 12 AWG
strip length : 0.31 - 0.35
terminal block intended wire size
screw driver
terminal block
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
DMX Power Supply 3 x 96 watt - Installation Instructions
Models PSDMX-3X96-24
Please read all instructions prior to installation and keep for future reference!
This class 2 power supply is to be installed by a qualified electrician in accordance with the National Electrical
Code (NEC) and local building codes. The power supply must be installed in a well ventilated area and free from
explosive gases and vapors. Proper operation requires the free flow of air. Power supply is well suited for LED or
resistive loads at or below their maximum output rating per circuit. Suitable For Damp Location.
WARNING! Risk of Fire or Electric Shock, Do Not Interconnect Output Terminal.
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV1.3
0 519 2 0 2 3
2 / 3
PLENUM FOR
SUCH USE IN
ACCORDANCE
WITH UL2043
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
L
N
GRD
Input
120-277V AC
D2
D1
3 x 96W DMX Power Supply
DMX
OUT
to the next
power supply!
- +
D- D+
GND
-
+
to Controller
power supply
DMX
IN
D3
L
N
GRD
D2
D1
3 x 96W DMX Power Supply
DMX
OUT
DMX
IN
D3
L
N
GRD
D2
D1
3 x 96W DMX Power Supply
DMX
OUT
DMX
IN
D3
Input
120-277V AC
Input
120-277V AC
DMX cables
(For DMX cable, use Belden
9829, 9842 or CAT5 shielded twisted
pair cabling or equivalent)
N/A
N/A
(-)
shield
N/A
N/A
shield
(-)
(+)
to the next
power supply!
N/A
N/A
shield
(-)
(+)
to the next
power supply!
N/A
N/A
shield
(-)
(+)
(+)
(+)
(+)
(+)
(-)
(-)
(-)
(-)
(+)
(+)
(+)
(+)
(-)
(-)
(-)
(-)
96W MAX PER TERMINAL
96W MAX PER TERMINAL
96W MAX PER TERMINAL
(+)
WW-
CW-
WW-
CW-
(+)
(+)
WW-
CW-
WW-
CW-
(+)
(+)
WW-
CW-
WW-
CW-
(+)
RGB/RGBW Tape
Static White Tape
Static White Tape
Configuration of the LED groups:
Press M and + simultaneously, in the LED menu choose
1-4L and save this setting by pressing M.
Dynamic White Tape
Dynamic White Tape
(+)
- +
D- D+
GND
-
+
to Controller
power supply
DMX cables
(For DMX cable, use Belden
9829, 9842 or CAT5 shielded twisted
pair cabling or equivalent)
(-)
shield
N/A
N/A
(+)
Controller
- +
D- D+
GND
-
+
to Controller
power supply
DMX cables
(For DMX cable, use Belden
9829, 9842 or CAT5 shielded twisted
pair cabling or equivalent)
(-)
shield
N/A
N/A
(+)
Controller
Controller
R
G
B
W
+24V R
G
B
W
+24V R
G
B
W
+24V
R
G
B
W
+24V R
G
B
W
+24V R
G
B
W
+24V
R
G
B
W
+24V R
G
B
W
+24V R
G
B
W
+24V
(+)
(+)
(+)
(+)
(-)
(-)
(-)
(-)
DMX Power Supply 3 x 96 watt - Installation Instructions
Models PSDMX-3X96-24
Please read all instructions prior to installation and keep for future reference!
This class 2 power supply is to be installed by a qualified electrician in accordance with the National Electrical
Code (NEC) and local building codes. The power supply must be installed in a well ventilated area and free from
explosive gases and vapors. Proper operation requires the free flow of air. Power supply is well suited for LED or
resistive loads at or below their maximum output rating per circuit. Suitable For Damp Location.
WARNING! Risk of Fire or Electric Shock, Do Not Interconnect Output Terminal.
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV1.3
0 519 2 0 2 3
3 / 3
PLENUM FOR
SUCH USE IN
ACCORDANCE
WITH UL2043
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
luminii PS010VD-3X96-24-WW User manual
-
luminii PDC-96-24 User manual
-
luminii Matrix Mini Plus Dynamic White Installation guide
-
-
luminii PSDALI-DT8-96-24 User manual
-
-
-
-
-
Other documents
-
Sunricher SR-SB1029-5C Operating instructions
-
DIODE LED DMX decoder Installation guide
-
ZIGBEE 114729 User manual
-
Radium LMZA4000 User manual
-
HEB LIGHTING E1-D User manual
-
SKYDANCE E1-D User manual
-
LEDEXPERT E1-B Hand Sweep Sensor Switch Operating instructions
-
TRAN LED QZ-DMX Installation guide
-
Q-tran Q-TRAN QZ-ND Compact LED Drivers Installation guide
-
iLight Handrail Operating instructions
