Smart Audio Soundbar TV Mount Installation Guide | 009-1986-00 45 Perseverance Way, Hyannis, MA 02601
Copyright 2020 Savant Systems, Inc | 201104 1 of 2 savant.com | 508.683.2500
Savant Smart Audio Soundbar TV Mount Installation Guide
Box Contents
(2) L-Shaped Bracket w/Cable Cutout Assembly (093-3115-xx)
(2) C-Shape Bracket w/Cable Cutout (071-1304-xx)
(2) UMB Stabilizer (015-0223-xx)
(4) M5x10 mm Hex Screws (039-0440-xx)
(4) Washer 25mm OD, 5mm ID (039-0437-xx)
(1) Installation Guide (this document)
Bracket Selection
The choice of bracket is based on the thickness of the TV. Ideally the
Soundbar should be flush with the front of the TV.
TV Thickness Bracket Extension Distance from
Wall
0.9 - 1.2 in
(2.3 - 3.7 cm)
C-Shape None 1.1 in
(2.8 cm)
1.8 - 2.8 in
(4.6 - 7.1 cm)
C-Shape 50 mm 1.1 in
(2.8 cm)
2.7 - 3.6 in
(6.8 - 9.1 cm)
C-Shape 70 mm 1.1 in
(2.8 cm)
2.1 - 2.5 in
(5.3 - 6.4 cm)
L-Shape None None
3.0 - 4.0 in
(7.6 - 10.2 cm)
L-Shape 50 mm None
3.8 - 4.7 in
(9.7 - 11.9 cm)
L-Shape 70 mm None
TV Thickness - Depth of the TV from the front of the screen to the
back of the VESA mounting points.
Minimum Distance from Wall - Refers to the distance from the
Soundbar mounting bracket at the VESA mounting points, and the
wall behind the TV.
NOTE: If bracket extensions are required they are included with the
Soundbar. Also some M5x10mm screws included with the soundbar
will be required.
Basic Information
The TV Mount Hardware is designed to be used with the VESA
Mounting points on flat panel televisions. The Installer MUST verify that
the TV mount/stand can hold the excess weight of the Soundbar. The
Soundbar can be mounted above or below a TV.
HELPFUL INFO: The slot that contains the mounting slides is
the bottom of the soundbar. As long as this slot is facing down and
the speakers are facing the listener, The left/right channels will be
assigned correctly by default.
IMPORTANT!
– If the bolts that were included with the TV mount in use are not
long enough to account for the extra 0.3 in (8mm) longer bolts will
have to be acquired.
– The images in the installation sections show L-Shaped or C-Shaped
brackets without the cable cutout. This does not change the
installation method.
Change Bracket Type
The mounting bracket assembly comes with the L-Shaped Bracket
installed. To change the bracket type do the following:
1. Use a 5/16th (8mm) wrench or socket to loosen the set bolt. Do not
remove the set bolt completely.
Set Bolt
2. Flip over the bracket
3. Slide out the L-Shaped bracket.
4. Check that the lock nut is still aligned.
Lock Nut
5. Slide in the C-Shaped bracket.
6. Tighten the set bolt.
Smart Audio Soundbar TV Mount Installation Guide | 009-1986-00 45 Perseverance Way, Hyannis, MA 02601
Copyright 2020 Savant Systems, Inc | 201104 2 of 2 savant.com | 508.683.2500
Method 1
Recommended method for installation. This method may require two
people to complete.
1. Choose the desired mounting bracket. Use the Bracket Selection
table on the previous page.
2. If necessary follow the instruction in the Change Bracket Type
section on the previous page.
3. Remove the TV from the Mount/Stand.
4. Place the TV display side down on a soft non-abrasive surface.
5. Remove any existing mounting bracket and screws from the VESA
mounting points.
VESA
mounting points
6. Place Soundbar face down on the same service as the TV.
7. Align the Soundbar to the desired location above or below the TV.
8. Adjust the length of the mounting brackets.
9. Align the mounting bracket to the TV’s VESA points.
Brackets
Aligned with the VESA mounting points
10. Attach the TV mount with the Soundbar mounting brackets
between the mount and the TV. Hand tighten only at this time.
11. Attach the optional extension brackets if needed.
12. Align the mounting slide with the brackets
13. Attach the Soundbar.
Optional Extension Bracket
L-Shape Bracket
14. Check alignment of soundbar. Make any adjustments needed.
15. Tighten all screws and bolts on mounting hardware.
16. Reattach to the TV mount/stand.
Bracket Installation
Method 2
This method can be more time consuming, but is easier for one person
to complete without assistance.
1. Follow steps 1 to 5 in method 1.
2. Align the mounting brackets to the TV’s VESA points.
3. Tighten the VESA bolts on the TV mount.
4. Reattach to the TV mount/stand.
5. Adjust the height of the Soundbar bracket.
NOTE: If the L/C-Shaped bracket does not slide easily loosen the
VESA bolts 1/2 turn.
6. Attach the optional extension brackets if needed.
7. Align the mounting slides in the Soundbar.
8. Attach the Soundbar to the mounting bracket.
Optional Extension Bracket
L-Shape Bracket shown here
9. Tighten all mounting bolts and screws.
UMB Stabilzers
1. In cases where the VESA mounting points are narrowly spaced or
non VESA compliant use of the UMB Stabilizers is suggested.
2. Locate a section of the TV’s chassis as close to the end of the
Slider Arm that is flat enough to mount the stabilizer foot
preferably close to the edge of the TV.
3. Clean the intended attachment area on the TV chassis with an
alcohol wipe to remove any latent grease.
4. To install the Slider Arm, first screw one of the Stabilizer Nuts onto
the thread, close to the swivel base. Place the assembly underneath
the Slider Arm and insert the threads through the Arm slot.
5. Once in place, peel the red backing film o of the base and stick
firmly to the TV chassis.
6. Install the second nut onto the threads and tighten both in place to
hold the speaker brackets in the correct placement.
Back of the TV
Mounting Bracket
UMB Stabilizer
7. Break o the any additional thread of the stabilizer with a pair of
pliers.
/
