Savant MNT-STUDIO-TV-00 Reference guide

Brand: Savant

Model: MNT-STUDIO-TV-00

Type: Reference guide

Studio Soundbar TV Mount Installation Guide | 009-2001-00 45 Perseverance Way, Hyannis, MA 02601

1 of 2

www.savant.com/artisonspeakers | 508.683.2500

Artison Studio Soundbars TV Mount Installation Guide [MNT-STUDIO-TV]

Box Contents

(2) L-Shaped Bracket Assembly (093-3221-xx)

(2) C-Shape Bracket (071-1111-xx)

(2) UMB Stabilizer (015-0223-xx)

(4) Undermount Spacer (015-0271-xx)

(4) Washer 25mm OD, 5mm ID (039-0437-xx)

(4) M4x11.5mm Hex Screw (039-0441-xx)

(4) M5x11.5mm Hex Screw (039-0442-xx)

(4) M6x11.5mm Hex Screw (039-0443-xx)

(4) M8x11.5mm Hex Screw (039-0444-xx)

(4) M10x11.5mm Hex Screw (039-0445-xx)

(1) Installation Guide (this document)

Basic Information

The TV Mount Hardware is designed to be used with the VESA

Mounting points on ﬂat panel televisions. The Installer MUST verify that

the TV mount/stand can hold the excess weight of the Soundbar. The

Soundbar can be mounted above or below a TV.

IMPORTANT! If the bolts that were included with the TV mount

in use are not long enough to account for the extra 0.3 in (8mm)

longer bolts will have to be acquired.

Bracket Selection

The choice of bracket is based on the thickness of the TV. Ideally the

Soundbar should be ﬂush with the front of the TV.

TV Thickness Bracket Extension Distance from

Wall

0.9 - 1.2 in

(2.3 - 3.7 cm)

C-Shape None 1.1 in (2.8 cm)

1.8 - 2.8 in

(4.6 - 7.1 cm)

C-Shape 50 mm 1.1 in (2.8 cm)

2.7 - 3.6 in

(6.8 - 9.1 cm)

C-Shape 70 mm 1.1 in (2.8 cm)

2.1 - 2.5 in

(5.3 - 6.4 cm)

L-Shape None None

3.0 - 4.0 in

(7.6 - 10.2 cm)

L-Shape 50 mm None

3.8 - 4.7 in

(9.7 - 11.9 cm)

L-Shape 70 mm None

TV Thickness - Depth of the TV from the front of the screen to the

back of the VESA mounting points.

Distance from Wall - Refers to the distance from the Soundbar

mounting bracket at the VESA mounting points, and the wall behind

the TV.

NOTE: If bracket extensions are required they are included with the

Soundbar. Also some M5x10mm screws and washers included with the

soundbar will be required.

Change Bracket Type

The mounting bracket assembly comes with the L-Shaped Bracket

installed. To change the bracket type do the following:

1. Use a 5/16th (8mm) wrench or socket to loosen the set bolt. Do not

remove the set bolt completely.

Set Bolt

2. Flip over the bracket

3. Slide out the L-Shaped bracket.

4. Check that the lock nut is still aligned.

Lock Nut

5. Slide in the C-Shaped bracket.

6. Tighten the set bolt.

Studio Soundbar TV Mount Installation Guide | 009-2001-00 45 Perseverance Way, Hyannis, MA 02601

2 of 2

www.savant.com/artisonspeakers | 508.683.2500

Attach Soundbar Brackets to TV

The steps below detail the process for attaching the bracket to the

back of the TV.

1. Choose the desired mounting bracket. Use the Bracket Selection

table on the previous page.

2. If necessary follow the instruction in the Change Bracket Type

section on the previous page.

3. Remove the TV from the Mount/Stand.

4. Place the TV display side down on a soft non-abrasive surface

5. Remove any existing mounting bracket and screws from the VESA

mounting points.

VESA

mounting points

6. Gently place the Soundbar face down on the same surface as the

TV, as to not damage the front tweeters.

7. Align the Soundbar to the desired location above or below the TV.

8. Adjust the length of the mounting brackets and align the mounting

brackets to the TV’s VESA points.

9. Insert undermount spacer.

Brackets

Aligned with the VESA mounting points

Undermount

Spacer

10. Attach the mounting bracket to the TV. The soundbar brackets

should be between the TV and the TV mount. Hand tighten the

VESA bolts only at this time.

Bracket Installation

Attach Soundbar to Brackets

The steps below detail the process for attaching the Soundbar to the

mounting brackets after the TV is installed onto the original mount/

stand.

1. Reattach the TV onto the mount/stand.

2. Adjust the height of the Soundbar bracket.

NOTE: If the L/C-Shaped bracket does not slide easily loosen the

VESA bolts 1/2 turn.

3. Attach the optional extension brackets if needed.

4. Align the mounting slides in the Soundbar.

5. Attach the Soundbar to the mounting bracket.

Optional Extension Bracket

L-Shape Bracket shown here

6. Tighten all mounting bolts and screws.

UMB Stabilizers

It is recommended to use the UMB stabilizers for added stability,

however for smaller TVs it may not be necessary. Refer to the UMB

Stabilizers steps below before proceeding to the Attach Soundbar to

Brackets section.

1. Locate a section of the TV’s chassis as close to the end of the

Slider Arm that is ﬂat enough to mount the stabilizer foot

preferably close to the edge of the TV.

2. Clean the intended attachment area on the TV chassis with an

alcohol wipe to remove any latent grease.

3. To install the Slider Arm, ﬁrst screw one of the Stabilizer Nuts onto

the thread, close to the swivel base. Place the assembly underneath

the Slider Arm and insert the threads through the Arm slot.

4. Once in place, peel the red backing ﬁlm o of the base and stick

ﬁrmly to the TV chassis.

5. Install the second nut onto the threads and tighten both in place to

hold the speaker brackets in the correct placement.

Back of the TV

Mounting Bracket

UMB Stabilizer

6. Break o the any additional thread of the stabilizer with a pair of

pliers.

Savant MNT-STUDIO-TV-00 Reference guide

Savant MNT-STUDIO-TV-00 Reference guide

Savant MNT-STUDIO-TV-00 Reference guide

Related papers

Other documents