2. Bay Networks
  3. 5380
5380

Bay Networks 5380, 5000, 5580, 5780 Quick Install Manual

  • Hello! I am an AI chatbot trained to assist you with the Bay Networks 5380 Quick Install Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the purpose of the flash memory card in a router?
    Which Bay Networks routers use flash memory cards?
    Where is the flash memory card slot located on the Model 5780 ATM Router?
    What precautions should be taken when installing a flash memory card?
    How can I remove a flash memory card from the router?
    Why is it recommended to make a backup copy of the configuration files on a separate flash memory card?
    What is the purpose of the read/write protect switch on the flash memory card?
Part No. 112770-A
May 1996
Quick Installation
for Flash Memory
Cards
112770-A QI F/M Cards Page 1 Tuesday, December 17, 1996 6:43 AM
2
Introduction
The System 5000
™
routers use flash memory cards to provide
storage for the nonvolatile file system (NVFS). The router
installation and configuration files are stored on flash memory
cards.
You must remove the Model 5380 Ethernet Router and the Model
5580 Token Ring Router modules from the chassis to install the
memory card. The Model 5780 ATM Router module has an
installation slot on the front.
CAUTION:
Only qualified technicians should install
this equipment.
Place all printed circuit boards on an antistatic mat
until you are ready to install them. If you do not have
an antistatic mat, wear a discharge leash to free
yourself of static before touching any of the printed
circuit boards or free yourself of static by touching a
grounded metal object before handling a printed circuit
board.
112770-A QI F/M Cards Page 2 Tuesday, December 17, 1996 6:43 AM
3
Installing a Flash Memory Card
1. Position the card with the label facing up and the
INSERT arrow pointing toward the card slot.
2. Insert the card into the slot, and push the card until it fits
snugly into place.
Model 5380 Ethernet or
Model 5580 Token Ring Router
6563.1
6501.2
Model 5780 ATM Router
112770-A QI F/M Cards Page 3 Tuesday, December 17, 1996 6:43 AM
4
Removing a Flash Memory Card
1. Remove the router from the chassis.
Refer to
Using the Model 5380 Ethernet and Model 5580
Token Ring Routers
for information about removing the
router.
CAUTION:
The pins on the edge of the card can be
damaged if you do not pull the card straight out from
the socket.
112770-A QI F/M Cards Page 4 Tuesday, December 17, 1996 6:43 AM
5
2. Remove the flash memory card by gently pulling the card
away from the connectors, or by pressing the button next
to the slot.
6694.1
Model 5380 Ethernet or
Model 5580 Token Ring Router
6502.1
Model 5780 ATM Router
112770-A QI F/M Cards Page 5 Tuesday, December 17, 1996 6:43 AM
6
Protecting Files on the Flash Memory Card
Bay Networks ships each memory card with its read/write
protect switch in the unprotected position. Bay Networks
recommends making a copy of your configuration files on
another flash memory card, write-protecting the card, and storing
it in a safe place for backup purposes.
1. Remove the memory card, as described on page 5.
NOTE:
You typically do not operate a router with a
write-protected memory card. You may need to
permanently store online network changes and
software upgrades, or to restore network operation by
downloading changes.
112770-A QI F/M Cards Page 6 Tuesday, December 17, 1996 6:43 AM
7
2. Set the read/write protect switch located on the edge
opposite the INSERT arrow of the memory card.
3. Insert the memory card as described in “Installing a
Flash Memory Card” earlier in this guide.
6498.1
Protected
Unprotected
112770-A QI F/M Cards Page 7 Tuesday, December 17, 1996 6:43 AM
/