Reely 1600320 Operating instructions

Category
Remote controlled toys
Type
Operating instructions

This manual is also suitable for

• Whenoperating the model aircraft, sufcientcooling must be provided forthe
controlunitandmotor.
• Avoidblockingthedrive.Thehighvoltagecoulddestroythemotorand/ortheight
controller.Ifthemotorisblockedbyforexampleanobstructionofthepropeller,
immediatelymovethecontrolleverforthemotorfunctiontotheoffposition.
• Whenusingageareddrive,makesureithasasmooth,regularlyserviceddrive
train.
• Handletheproductwithcare;itcanbedamagedbyimpact,blows,oraccidental
dropping,evenfromalowheight.
• Donotleavethepackagingmateriallyingaroundcarelessly,sinceitcouldbecome
adangeroustoyforchildren.
Switching on the ight controller
1 Connectioncables
2 Connectingplugsofreceiver
3 Planecontrolunit
4 Jumperforbreakfunction
5 Jumperforbatterytype
6 Motorconnectioncables
7 Brushlesselectricmotor
Connectthetwomotorconnectioncables(6)ontherightsidesofthecontrolunittothemotor
(7).Dependingontheintendeduse,youcouldsolderthecablesontothemotororuseplug
connectorstoadapttotheperformancerangeofthecontrolunit.Ineachcasetheconnectors
mustbeconnectedsothatthecable(forexamplebyusingappropriateshrinkingtubes)are
securedagainstshortcircuits.
Whenconnectingthemotor,ensurethatthepolarityofthecableiscorrect,sothatthemotor
doesnotrotateintheoppositedirection(redcable=positivepolarity/+,blackcable=nega-
tivepolarity/-).Theconnectedelectricmotormustbeproperlyprotectedfrominterferenceas
prescribedbythemanufacturer.
Solderaplugtothebatterycables(1)thattyourchosenbatteryplugsystem.Payattentionto
therightpolarity(redcable=positivepole/+,blackcable=negativepole/-).
Set the jumpers
Thebreakfunctionaswellasthebatterytypeusedcanbesetusingbothjumpers.
Whenusingaelectricglidermodelwithfold-waypropeller,youmustactivatethebreak.Insert
thetopjumper(4)sothatthemiddleandtopcontactareconnectedtoeachother(BrakeON).
Inamodelplanewitharigidpropeller,thebrakemustbedeactivated.Insertthetopjumper(4)
sothatthemiddleandlowercontactareconnectedtoeachother(BrakeOFF).
WhenusingaLiPodrivebattery,thelowerjumper(5)mustbeinsertedsothatthemiddleand
theuppercontactareconnected("Li-xx").Whenreaching3V/cell,thecontrollerreducesthe
motorpowertoprotectthebatteryfromtotaldischarge.WhenusingaNiCd/NiMHdrivebattery,
thelowerjumper(5)mustbeinsertedsothatthemiddleandthelowercontactsareconnected
("Ni-xx").
Important!
Thejumpersmayonlybereconnectediftheplanebatteryisnotconnectedtothe
controller.Neverreconnectthejumperswhiletheplanebatteryisstillconnectedto
thecontroller.
Mounting the control unit
Iftheproductistobeusedasareplacementforanexistingightcontroller,rstremovetheold
controlunitfromyourmodel.
Nowmountthecontrolunittothemodel.Dependingonthespaceavailable,selectthesame
mountinglocation.Ideallythisshouldbeasfarawayfromthereceiveraspossible.Thecontrol
unitshouldalsonotbedirectlynexttothemotor.
Hook-and-looptape or adouble-sided adhesivetape canbe used tomount the
controlunit.
Positionallcablessothattheycannotbecomeentangledinrotatingormovingpartsofthe
model.Usecabletiestoafxthem,forexample.
Operating Instructions
Brushless model plane control unit
Item no. 1600319 (20 A)
Item no. 1600320 (30 A)
Intended Use
Theproductisanelectronicmodelplanecontrolunit,whichisconnectedtoafreechannelof
aremotecontrolreceiverformodelaeroplaneswithsteplessspeedadjustmentofabrushless
motor(collectormotorwithtwoterminals).ThecontrolunithasaBECcircuit,whichsupplies
powertotheradioreceiverandtheconnectedservosfromtheightbatteries.
Forsafetyandcompliancereasons,theproductmustnotbeconvertedand/ormodiedinany
way.Ifyouusetheproductforotherpurposesthanthosedescribedabove,theproductmaybe
damaged.Furthermore,improperusecancauseriskssuchasshort-circuits,re,etc.Please
readtheoperatinginstructionscarefullyanddonotdiscardthem.Ifyoupasstheproductonto
athirdparty,pleaseincludetheoperatinginstructions.
Thisproductcomplieswiththeapplicable national andEuropeanregulations.Allnamesof
companiesandproductsarethetrademarksoftherespectiveowners.Allrightsreserved.
Package contents
• Planecontrolunit
• Operatinginstructions
Latest operating instructions
Downloadthelatestoperatinginstructionsviathelinkwww.conrad.com/downloadsorscanthe
QRcodeshownhere.Followtheinstructionsonthewebsite.
Explanation of symbols
Anexclamationmarkinsideatriangleindicatesimportantinstructionsinthisoperat-
ingmanualwhichmustbeadheredto.
Thearrowsymbolindicatesspecictipsandadviceonoperation.
Safety Instructions
The warranty/guarantee will be void in the event of damage caused by non-
compliance with these safety instructions. We do not assume any liability for
any resulting damage!
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions! The
warranty/guarantee will be void in such cases.
• Unauthorised conversion and/or modication of the product is not allowed for
safetyandapprovalreasons.Neverdisassembletheproduct;therearenocom-
ponentsinsidethehousingthatrequiresettingorservicing.Besides,thiswillin-
validatethewarranty!
• Theproductisnotatoyandshouldbekeptoutofthereachofchildren!
• Theplanecontrolunitmustnotgetdamporwet.
• Alwaysswitchonthetransmitterrstandputtheoperatingleverforthemotorin
thelowestposition(motoroff).Onlyafterthat,connecttheplanecontrolunitto
thebatterypackandswitchiton.Whenswitchingoffproceedinthereverseorder.
First,whenthemotorisnotrunning,thecontrolunitmustbedisconnectedfrom
thebattery,afterwhichthetransmittercanbeturnedoff.
• Alwaysdisconnectthebatteryfromthecontrolunitwhennotinuse.
• Beforerechargingthebatteryitmustbedisconnectedfromthecontrolunit.
• ThecontrolunitcanbeoperatedwithNiMH-/NiCdaswellasLiPobatteries.
• Themaximumallowedvoltageandcurrentvalue(seesection:TechnicalData)
maynotbeexceeded,otherwisethemotorand/orightcontrollercouldbede-
stroyed.Non-compliancewiththelimitswillvoidtheguarantee/warranty.
• Themotor,controlunitandbatteriescanbecomeveryhotduringoperation.This
mayresultinseriousburns.
• Whenhandlingmodelaircraft,makesurenopartsofthebodyorobjectscome
intocontactwithrotatingparts.Improperhandlingwillincreasetheriskofinjury!
• Onlyoperatethecontrolunitwithabatterypack;neverwithapoweradapter.
• Onlyconnectonesinglebrushlessmotortotheightcontroller.
• Thebrushlesscontrolunitisnotsuitableforoperatingbrushlessmotorswiththree
connections!
• Maintainthebiggestpossibledistancebetweenthereceiverandcontrolunit/motor
fortheinstallationtoavoidinteraction.
• Donotinstallthereceiver'santennacableparalleltothecurrent-carryingcables.
Connection to the receiver
Connectthethree-pinplugofthecontrolunit(2)totheoutputofthereceiverfromwhichthe
motorcontrolsignalsaretransmitted.Makeabsolutelysureyouhavethecorrectreceivercon-
gurationandthattheplug'spolarityiscorrect(seeoperationinstructionsforthereceiveras
wellastheinscriptiononthereceiver).
Whitecable:Controlsignal
Redcable:OperatingvoltagePositive(+)
Blackcable:OperatingvoltageNegative(-)
Important!
Thebuilt-inBECsystemsuppliesthenecessarycurrenttotheconnectedreceiver
andservo.
Iftheservo'scurrentconsumptionishigherthan1A,removethemiddlecontact(the
contactwiththeredcable)fromthe3-pinconnectorconnectedtothereceiver.Use
aneedletoliftthecontact'slockingtongueandpullthecontactbackwardsfromthe
connector.Theninsulatetheopencontactplugwithshrinktubingorinsulationtape.
Thepowersupplyofthereceiverandtheservomustnowbeconnectedviaasepa-
ratereceiverbattery.
SimultaneousoperationofthereceiverbatteryandBECsystemisnotpermitted!
Failuretocomplywiththisinstructionwilldestroythecontrolunit!Thewarranty/
guaranteewillbevoid!
Using the control unit
• Beforeuse,checkthatthepolarityofallconnectionsiscorrectandthatbothjumpersare
setcorrectly.
Forsafetyreasonsthepropellershouldbedismantledforthersttestofthedrive
unit.
Duringmotortestrunswithapropeller,makesurenoobjectsorbodypartsarenear
therotationandintakeareaofthepropeller.
• Turnthetransmitteronandslidethecontrolstickforthemotorfunctiontothelowestposition
(motoroff).Thetrimsettingforthemotorfunctionmustbeinthecentrepositionorotherwise
thelowestsetting.
• Connectthedrivebatterytothecontrolunit.
• Oncethepowersupplytothecontrolunitisturnedon,itwillperformaself-test.Oncethe
self-testhasbeensuccessfullycompleted,themotorwillsoundalongsignaltone.
• Nowmovethejoystickgraduallyinthedirectionofmax.motorpoweruntilthemotorstarts
andcheckthatthemotorisrunningintherightdirection.Ifnot,swapthepolarityofthemotor
connectioncables(6).
• Nowtestthecorrectfunctioningofthemotorcontrol.
Warning signals
Thecontrolunitindicatesproblemsbysoundingwarningsignals.Thesearegener-
atedbyshortactivation of theconnectedmotor.Sincethe beeps areveryquiet
dependingonthemotorused,itmustbeabsolutelyquietintheroomsothatthe
soundscanbeheardclearly.
• Ifthesupplycurrentistoolow,twoshortwarningsignalswillsoundcontinuously,followedby
apauseofapproximately1.5seconds.
• Ifthesupplycurrentistoohigh,thecontrolunitwillemitlongwarningsignalsevery4sec-
onds.
• Ifthecontrolunitnolongerreceivesavalidsignal,itwillemitashortbeep1.5seconds.Inthis
case,theconnectedmotorwillbeswitchedoff.Oncethecontrolunitreceivesagoodsignal
again,themotorandpositionsofthecontrolleverwillbeactivatedagain.
• Ifthemotorcontrolleverisnotinthemotoroffpositionwhentheightbatteryisconnected,or
ifthetrimissetincorrectly,themotorwillbrieyemitbeepsinrapidsuccession.Ifthecontrol
leverandtrimmingareinthecorrectpositionbutthemotorstillemitsshortwarningsignals,
changethecontroldirectionofthecontrolchannelforthemotorusingthereversefunction.
Ending operation
Todeactivatethecontrolunit,turnoffthemotorusingtheremotecontrol/transmitter.Then
removethebatteryfromtheplanecontrolunitandturnoffthetransmitter.
Disposal
Theproductmustnotbedisposedofwiththehouseholdwaste.Disposeofanun-
serviceabledeviceinaccordancewiththerelevantstatutoryregulations.
Technical Data
Item no. 1600319 1600320
Type Controlunit20A Controlunit30A
NumberofNiCd/NiMHcells 5–10 5–10
NumberofLiPocells 2–3 2–3
Max.continuouscurrent 20A 30A
Max.current(<10seconds) 25A 40A
Pulsefrequency 2kHz 2kHz
BEC 5V/DC,1A 5V/DC,1A
Receiverconnection JR JR
OvertemperatureProtection 110°C 110°C
Dimensionswithoutcable
LxWxH
45x21x8mm 45x21x8mm
Weight 17g 21g
ThisisapublicationbyConradElectronicSE,Klaus-Conrad-Str.1,D-92240Hirschau(www.conrad.com).
Allrightsincludingtranslationreserved.Reproductionbyanymethod,e.g.photocopy,microlming,orthecapturein
electronicdataprocessingsystemsrequirethepriorwrittenapprovalbytheeditor.Reprinting,alsoinpart,isprohibited.
Thispublicationrepresentthetechnicalstatusatthetimeofprinting.
Copyright2018byConradElectronicSE.  *1600319_20_V1_0118_02_VTP_m_en
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Reely 1600320 Operating instructions

Category
Remote controlled toys
Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI