Page is loading ...
TE-111
Telephone Entry Controller
1
S4 S5 S6
On 5 Yes #
3 off off off Off 3 No *
5 off off on
8 off on off
15 off on on
20 on off off
40 on off on
100 on on off
240 on on on
2x3 ring
patern
Key on
phone
Strike duration
Seconds S1 S2 S3
# of rings
3
Basic Installation Steps:
1. Mount the TE-111 near the main telephone distribution
center of the house and attach the telephone line from the
service provider to the connection labeled “Line”
.
2. Connect the main house phone distribution system to the
wire terminals labeled “Tel”.
3. Connect the TE-111 to the Chanel Vision DP or IU series
door plate. Note: The correct companion board to use is
300-001 (300001)
4. Connect power supply.
Basic Configuration:
Configure switches S4 and S5 to select the desired ring
pattern.
Set switch S6 to either # or * to determine which key will
activate the system.
Basic Operation:
When you hear the distinctive ring pattern selected above:
within 20 seconds - simply pick up the telephone to be
connected to the door speaker.
after 20 seconds - pick up the telephone and press ## (or **)
to be connected to the door speaker.
If you are already on the phone when the doorbell button is
pressed you will hear a call waiting tone. Simply press ##
(or **) to put your call on hold while you are connected to
the door speaker. Press ## (or **) to return to your call.
2
Basic Connection
Door Plate Connection
(IU-xxxx or DP-xxxx)
Front Side view
Back Side view
Telephone Service Provider
House
Telephones
12VAC
500mA
On
S4
S5
S6
Off
Power
Line
Tel
Intercom
Connect 2 Wires Between
Your Door Plate And The TE-111
Strike duration
Seconds S1 S2 S3
3
5
8
15
20
40
120
240
off
on
off off
on
off
on
off
on
off
off
on
on
off
off
on
on
off
off
off
on
on
on
on
On
Off
# of rings
2x3 ring
patern
Key on
phone
Yes
No
#
*
S4
S5
S6
3
5
On
Off
# of rings
2x3 ring
patern
Key on
phone
Yes
No
#
*
S4
S5
S6
3
5
The TE-111 provides communication between the front door and
any phone in the house. When a visitor presses the doorbell button
the phones in the house will respond with a distinctive ring. The
home owner can then speak to the visitor by answering any of the
ringing phones in the house.
3
Basic Installation Steps:
1. Mount the TE-111 near the main telephone distribution
center of the house and attach the telephone line from the
service provider to the connection labeled “Line”
.
2. Connect the main house phone distribution system to the
wire terminals labeled “Tel”.
3. Connect the TE-111 to the Chanel Vision DP or IU series
door plate. Note: The correct companion board to use is
300-001 (300001)
4. Connect power supply.
Basic Configuration:
Configure switches S4 and S5 to select the desired ring
pattern.
Set switch S6 to either # or * to determine which key will
activate the system.
Basic Operation:
When you hear the distinctive ring pattern selected above:
within 20 seconds - simply pick up the telephone to be
connected to the door speaker.
after 20 seconds - pick up the telephone and press ## (or **)
to be connected to the door speaker.
If you are already on the phone when the doorbell button is
pressed you will hear a call waiting tone. Simply press ##
(or **) to put your call on hold while you are connected to
the door speaker. Press ## (or **) to return to your call.
2
Basic Connection
Door Plate Connection
(IU-xxxx or DP-xxxx)
Front Side view
Back Side view
Telephone Service Provider
House
Telephones
12VAC
500mA
On
S4
S5
S6
Off
Power
Line
Tel
Intercom
Connect 2 Wires Between
Your Door Plate And The TE-111
Strike duration
Seconds S1 S2 S3
3
5
8
15
20
40
120
240
off
on
off off
on
off
on
off
on
off
off
on
on
off
off
on
on
off
off
off
on
on
on
on
On
Off
# of rings
2x3 ring
patern
Key on
phone
Yes
No
#
*
S4
S5
S6
3
5
On
Off
# of rings
2x3 ring
patern
Key on
phone
Yes
No
#
*
S4
S5
S6
3
5
The TE-111 provides communication between the front door and
any phone in the house. When a visitor presses the doorbell button
the phones in the house will respond with a distinctive ring. The
home owner can then speak to the visitor by answering any of the
ringing phones in the house.
TE110DS Installation Steps:
1. Complete Basic installation.
2. Connect the TE110DS (sold separately) in-line between
the main board and small board.
Basic Configuration:
Configure switches S1, S2 and S3 to select the duration of
the TE110DS relay closure.
Basic Operation:
To close the door strike relay while you are already
communicating with the door speaker, press #7 (or *7).
To close the door strike relay when you are not
communicating with the door speaker, press ## (or **)
and then press #7 (or *7).
Door Plate Connection
(IU-xxxx or DP-xxxx)
12VAC
500mA
TE110DS
(Sold Separately)
Strike
power
supply
Strike
power
supply
(DC+)
(DC-)
To Strike
Mechanism
To Strike
Mechanism
From TE-111
To Companion Board
(300-001)
Telephone ServiceProvider
On
S1
S2
S3
Off
House
Telephones
4
5
TE110DS Connection Details
TE110DS Connection Diagram
Strike duration
Seconds S1 S2 S3
3
5
8
15
20
40
120
240
off
on
off off
on
off
on
off
on
off
off
on
on
off
off
on
on
off
off
off
on
on
on
on
Strike duration
Seconds S1 S2 S3
3
5
8
15
20
40
120
240
off
on
off off
on
off
on
off
on
off
off
on
on
off
off
on
on
off
off
off
on
on
on
on
On
Off
# of rings
2x3 ring
patern
Key on
phone
Yes
No
#
*
S4
S5
S6
3
5
Power
Line
Tel
Intercom
The TE110DS is an optional relay that works with the TE-111 to control
an electronic opener.
TE110DS Installation Steps:
1. Complete Basic installation.
2. Connect the TE110DS (sold separately) in-line between
the main board and small board.
Basic Configuration:
Configure switches S1, S2 and S3 to select the duration of
the TE110DS relay closure.
Basic Operation:
To close the door strike relay while you are already
communicating with the door speaker, press #7 (or *7).
To close the door strike relay when you are not
communicating with the door speaker, press ## (or **)
and then press #7 (or *7).
Door Plate Connection
(IU-xxxx or DP-xxxx)
12VAC
500mA
TE110DS
(Sold Separately)
Strike
power
supply
Strike
power
supply
(DC+)
(DC-)
To Strike
Mechanism
To Strike
Mechanism
From TE-111
To Companion Board
(300-001)
Telephone ServiceProvider
On
S1
S2
S3
Off
House
Telephones
4
5
TE110DS Connection Details
TE110DS Connection Diagram
Strike duration
Seconds S1 S2 S3
3
5
8
15
20
40
120
240
off
on
off off
on
off
on
off
on
off
off
on
on
off
off
on
on
off
off
off
on
on
on
on
Strike duration
Seconds S1 S2 S3
3
5
8
15
20
40
120
240
off
on
off off
on
off
on
off
on
off
off
on
on
off
off
on
on
off
off
off
on
on
on
on
On
Off
# of rings
2x3 ring
patern
Key on
phone
Yes
No
#
*
S4
S5
S6
3
5
Power
Line
Tel
Intercom
The TE110DS is an optional relay that works with the TE-111 to control
an electronic opener.
Two Door Application:
1. Complete the basic installation, setting the TE-111 to
respond to the # key on your telephone.
2. Connect the house phones output from the first TE-111 to
the line in on the second TE-111.
3. Configure the second TE-111 to respond to the * key on
your telephone.
4. Set both units for different distinctive ring patterns.
Two Door Operation:
When you hear the distinctive ring pattern selected above:
within 20 seconds - simply pick up the telephone to be
connected to the door speaker.
after 20 seconds - pick up the telephone and press ## to be
connected to the front door speaker, or ** to be
connected to the back door speaker.
Specifications:
REN: >5
Power Supply: 12VAC 500mA
Dimensions:
TE-111: 6.5” x 5.0” x 2.4”
Specifications subject to change without notice.
Front Door - Back Door Application
House
Telephones
12VAC
500mA
Set dip switches to activate the
doorplate whenever ## is pressed.
Telephone
Service
Provider
12VAC
500mA
Front Door
Back Door
Set dip switches to activate the
doorplate whenever ** is pressed.
7
6
Strike duration
Seconds S1 S2 S3
3
5
8
15
20
40
120
240
off
on
off off
on
off
on
off
on
off
off
on
on
off
off
on
on
off
off
off
on
on
on
on
Strike duration
Seconds S1 S2 S3
3
5
8
15
20
40
120
240
off
on
off off
on
off
on
off
on
off
off
on
on
off
off
on
on
off
off
off
on
on
on
on
On
Off
# of rings
2x3 ring
patern
Key on
phone
Yes
No
#
*
S4
S5
S6
3
5
On
Off
# of rings
2x3 ring
patern
Key on
phone
Yes
No
#
*
S4
S5
S6
3
5
Power
Line
Tel
Intercom
Power
Line
Tel
Intercom
Two Door Application:
1. Complete the basic installation, setting the TE-111 to
respond to the # key on your telephone.
2. Connect the house phones output from the first TE-111 to
the line in on the second TE-111.
3. Configure the second TE-111 to respond to the * key on
your telephone.
4. Set both units for different distinctive ring patterns.
Two Door Operation:
When you hear the distinctive ring pattern selected above:
within 20 seconds - simply pick up the telephone to be
connected to the door speaker.
after 20 seconds - pick up the telephone and press ## to be
connected to the front door speaker, or ** to be
connected to the back door speaker.
Specifications:
REN: >5
Power Supply: 12VAC 500mA
Dimensions:
TE-111: 6.5” x 5.0” x 2.4”
Specifications subject to change without notice.
Front Door - Back Door Application
House
Telephones
12VAC
500mA
Set dip switches to activate the
doorplate whenever ## is pressed.
Telephone
Service
Provider
12VAC
500mA
Front Door
Back Door
Set dip switches to activate the
doorplate whenever ** is pressed.
7
6
Strike duration
Seconds S1 S2 S3
3
5
8
15
20
40
120
240
off
on
off off
on
off
on
off
on
off
off
on
on
off
off
on
on
off
off
off
on
on
on
on
Strike duration
Seconds S1 S2 S3
3
5
8
15
20
40
120
240
off
on
off off
on
off
on
off
on
off
off
on
on
off
off
on
on
off
off
off
on
on
on
on
On
Off
# of rings
2x3 ring
patern
Key on
phone
Yes
No
#
*
S4
S5
S6
3
5
On
Off
# of rings
2x3 ring
patern
Key on
phone
Yes
No
#
*
S4
S5
S6
3
5
Power
Line
Tel
Intercom
Power
Line
Tel
Intercom
500-026 Rev D
Channel Vision Technology will repair or replace any defect in material
or workmanship which occurs during normal use of this product with
new or rebuilt parts, free of charge in the USA, for one year from the
date of original purchase. This is a no hassle warranty with no mail in
warranty card needed. This warranty does not cover damages in
shipment, failures caused by other products not supplied by Channel
Vision Technology, or failures due to accident, misuse, abuse, or
alteration of the equipment. This warranty is extended only to the
original purchaser when purchased through an authorized reseller. A
purchase receipt, invoice, or other proof of original purchase date will
be required before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling
(714) 424-6500 or e-mailing [email protected]
A Return Authorization number must be obtained in advance and can
be marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other
rights (which vary from state to state). If a problem with this product
develops during or after the warranty period, please contact Channel
Vision Technology, your dealer or any factory-authorized service
center.
Channel Vision products are not intended for use in medical,
lifesaving, life sustaining or critical environment applications. Channel
Vision customers using or selling Channel Vision products for use in
such applications do so at their own risk and agree to fully indemnify
Channel Vision for any damages resulting from such improper use or
sale.
www.chann e l v i s i o n . c o m
234 Fischer Avenue, Costa Mesa, California 92626 USA
(714)424-6500 (800)840-0288 (714)424-6510 fax
email: [email protected]
1
/
