Black Box TE110A User manual

Category
Holders
Type
User manual

This manual is also suitable for

Black Box TE110A is a compact and versatile telephone entry controller that provides secure communication between a visitor at the door and occupants inside the building. It features a built-in keypad for easy access control, allowing authorized individuals to enter the premises using a personalized code. Additionally, it supports two-way audio and video communication, enabling occupants to see and speak with visitors before granting access.

Black Box TE110A is a compact and versatile telephone entry controller that provides secure communication between a visitor at the door and occupants inside the building. It features a built-in keypad for easy access control, allowing authorized individuals to enter the premises using a personalized code. Additionally, it supports two-way audio and video communication, enabling occupants to see and speak with visitors before granting access.

IU-XXXX
IU-XXXXC
IU-XXXXP
IU-XXXXP8
Telephone Entry Door Intercom
0
1
2
3
Channel Vision’s IU-Series are 1/4" solid brass door plates
that interface with a telephone entry controller to provide
communication with the front door. They are available in a
variety of configurations including options for a hidden
camera and compatibility with Panasonic’s popular KSU
phone systems. A standard single gang junction box is
supplied with each IU-series unit.
2.0”
RACO box model 8660
(included)
1.75”
3.8”
Dimensions:
IU-Series Intercom
2.75”
4.5”
Features:
h
h
h
h
h
1/4” thick solid brass plate
Discrete speaker and microphone
Hidden camera option available
Fits a single gang box
Available in 9 different finishes
3
Understanding the model number:
Understanding the compatibility options
(IU-0212C shown for example only)
Part numbering: IU door plates
IU-0212C
Blank P-0920, P-0921, & TE110/C-0920 compatible
C P-0930 compatible
P Panasonic compatible (KX-TA624)
P8 Panasonic compatible (KX-TA824/848, etc)
212 White
222 Polished Brass
232 Antique Brass
242 Chrome
252 Oil Rubbed Bronze
262 Antique Copper
272 Satin Silver
282 Black
302 Satin Nickel
0 No camera
6 Color camera (Note: camera option is not
available on IU-xxxxP8 models.)
There are three different types of systems that IU door plates can be
used with. The compatibility for these different types of systems is
indicated by the suffix of the model number which follows the 4-digit
numerical code.
If there is not a letter suffix on the model number, such as IU-0212,
that door plate is compatible with Channel Vision’s telephone entry
products including models P-0920, P-0921, C-0920, and TE110.
If the suffix is the letter “P”, such as IU-0212P, then the door plate is
compatible with Panasonic’s phone systems which are designed to
use the Panasonic door phone model: KXT-30865.
If the suffix is the letter “C”, such as IU-0212C, then the door plate is
compatible with Channel Vision’s Whole-House CAT5 Intercom Hub,
model P-0930.
Please double check to be sure that you have purchased the correct
model number for your application.
2
3
Channel Vision’s IU-Series are 1/4" solid brass door plates
that interface with a telephone entry controller to provide
communication with the front door. They are available in a
variety of configurations including options for a hidden
camera and compatibility with Panasonic’s popular KSU
phone systems. A standard single gang junction box is
supplied with each IU-series unit.
2.0”
RACO box model 8660
(included)
1.75”
3.8”
Dimensions:
IU-Series Intercom
2.75”
4.5”
Features:
h
h
h
h
h
1/4” thick solid brass plate
Discrete speaker and microphone
Hidden camera option available
Fits a single gang box
Available in 9 different finishes
3
Understanding the model number:
Understanding the compatibility options
(IU-0212C shown for example only)
Part numbering: IU door plates
IU-0212C
Blank P-0920, P-0921, & TE110/C-0920 compatible
C P-0930 compatible
P Panasonic compatible (KX-TA624)
P8 Panasonic compatible (KX-TA824/848, etc)
212 White
222 Polished Brass
232 Antique Brass
242 Chrome
252 Oil Rubbed Bronze
262 Antique Copper
272 Satin Silver
282 Black
302 Satin Nickel
0 No camera
6 Color camera (Note: camera option is not
available on IU-xxxxP8 models.)
There are three different types of systems that IU door plates can be
used with. The compatibility for these different types of systems is
indicated by the suffix of the model number which follows the 4-digit
numerical code.
If there is not a letter suffix on the model number, such as IU-0212,
that door plate is compatible with Channel Vision’s telephone entry
products including models P-0920, P-0921, C-0920, and TE110.
If the suffix is the letter “P”, such as IU-0212P, then the door plate is
compatible with Panasonic’s phone systems which are designed to
use the Panasonic door phone model: KXT-30865.
If the suffix is the letter “C”, such as IU-0212C, then the door plate is
compatible with Channel Vision’s Whole-House CAT5 Intercom Hub,
model P-0930.
Please double check to be sure that you have purchased the correct
model number for your application.
The IU-6xxx, and IU-6xxxP come with a mini camera that can be attached to
the integrated mount that allows the camera to see through the opening in
the plate. The illustrations bellow show how to mount the camera.
Attaching the Camera
Mini Pinhole Camera
Mounting Hole
Cone Lens
Connect Telephone Entry Controller here
(see following pages for details)
Connect to power supply
and video distribution system
Remove this
section of screen
material
Attach camera to mount
using the screw provided
Attach pigtail
to rear of
camera
Completed Sub-assembly
(see Attaching the Companion Board)
Break away the section of perforated metal screen that covers the camera
opening by pushing a screwdriver through the slot on the front of the door
plate. Press near the top or bottom of the section and the tabs that hold it in
place will break free. Attach the camera to the mount so that the cone of the
camera points through the opening. Adjust the camera to the desired position
and secure it in place by tightening the screw on the mount.
This door intercom product consists of two sub assemblies which must be
attached to each other before the final assembly can be installed. In this
guide the electronic sub assembly will be referred to as the “Companion
Board” and the mechanical assembly will be referred to as the “Door Plate.”
Review the following diagrams and assemble as shown.
Attaching the Companion Board
Companion Board Connection Details
To Button
To Speaker
Microphone
Companion Board
Place microphone
in this compartment
Place cap over
microphone
Connect Telephone Entry Controller here
(see following pages for details)
Completed Sub-assembly
Attach button and
speaker wires as shown
Attach Companion Board
with mounting screws
Remove the plastic cap that covers the microphone compartment on the
door plate. Place the microphone in the compartment and replace the plastic
cap over the microphone. Note that the plastic cap will form a friction fit over
the top of the microphone wires holding them snug against the outer
compartment wall until they exit at the base as shown. Remove the mounting
screws which are already attached to the bracket and use them to attach the
companion board. The companion board should mount on the front side of
the bracket so that the screws pass through the companion board before
threading into the bracket.
4
5
The IU-6xxx, and IU-6xxxP come with a mini camera that can be attached to
the integrated mount that allows the camera to see through the opening in
the plate. The illustrations bellow show how to mount the camera.
Attaching the Camera
Mini Pinhole Camera
Mounting Hole
Cone Lens
Connect Telephone Entry Controller here
(see following pages for details)
Connect to power supply
and video distribution system
Remove this
section of screen
material
Attach camera to mount
using the screw provided
Attach pigtail
to rear of
camera
Completed Sub-assembly
(see Attaching the Companion Board)
Break away the section of perforated metal screen that covers the camera
opening by pushing a screwdriver through the slot on the front of the door
plate. Press near the top or bottom of the section and the tabs that hold it in
place will break free. Attach the camera to the mount so that the cone of the
camera points through the opening. Adjust the camera to the desired position
and secure it in place by tightening the screw on the mount.
This door intercom product consists of two sub assemblies which must be
attached to each other before the final assembly can be installed. In this
guide the electronic sub assembly will be referred to as the “Companion
Board” and the mechanical assembly will be referred to as the “Door Plate.”
Review the following diagrams and assemble as shown.
Attaching the Companion Board
Companion Board Connection Details
To Button
To Speaker
Microphone
Companion Board
Place microphone
in this compartment
Place cap over
microphone
Connect Telephone Entry Controller here
(see following pages for details)
Completed Sub-assembly
Attach button and
speaker wires as shown
Attach Companion Board
with mounting screws
Remove the plastic cap that covers the microphone compartment on the
door plate. Place the microphone in the compartment and replace the plastic
cap over the microphone. Note that the plastic cap will form a friction fit over
the top of the microphone wires holding them snug against the outer
compartment wall until they exit at the base as shown. Remove the mounting
screws which are already attached to the bracket and use them to attach the
companion board. The companion board should mount on the front side of
the bracket so that the screws pass through the companion board before
threading into the bracket.
4
5
6
7
The IU-6xxxC comes with a mini color camera that can be attached to the
integrated mount that allows the camera to see through the opening in the
plate. The illustrations bellow show how to mount the camera.
Attaching the Camera
(IU-XXXXC)
Mini Pinhole Camera
Mounting Hole
Cone Lens
Connect Intercom Hub here
(see following pages for details)
Connect to power supply
and video distribution system
Break away the section of perforated metal screen that covers the camera
opening by pushing a screwdriver through the slot on the front of the door
plate. Press near the top or bottom of the section and the tabs that hold it in
place will break free. Attach the camera to the mount so that the cone of the
camera points through the opening. Adjust the camera to the desired position
and secure it in place by tightening the screw on the mount.
This door intercom product consists of two sub assemblies which must be
attached to each other before the final assembly can be installed. In this
guide the electronic sub assembly will be referred to as the “Companion
Board” and the mechanical assembly will be referred to as the “Door Plate.”
Review the following diagrams and assemble as shown.
Attaching the Companion Board
(IU-XXXXC)
Companion Board Connection Details
To Speaker
Microphone
(attached to back side)
Use D1 for Door1 chime sound
Use D2 for Door2 chime sound
Volume Adjustment
Companion Board
Microphone
Tube
Connect Intercom Hub here
(see following pages for details)
Bend mounting
tabs over to
secure the
Companion Board
Completed Sub-assembly
Attach button
and speaker
wires as shown
Align holes with
mounting tabs
Position the companion board onto the three mounting tabs as shown below.
The microphone attached to the back side of the companion board should
line up with the microphone tube on the bracket. Bend the mounting tabs to
secure the companion board. Connect the speaker and button wires by
sliding the small connector over the exposed pins on the companion board
as shown.
To Button
Remove this
section of screen
material
Attach camera to mount
using the screw provided
Attach pigtail
to rear of
camera
Completed Sub-assembly
(see Attaching the Companion Board)
6
7
The IU-6xxxC comes with a mini color camera that can be attached to the
integrated mount that allows the camera to see through the opening in the
plate. The illustrations bellow show how to mount the camera.
Attaching the Camera
(IU-XXXXC)
Mini Pinhole Camera
Mounting Hole
Cone Lens
Connect Intercom Hub here
(see following pages for details)
Connect to power supply
and video distribution system
Break away the section of perforated metal screen that covers the camera
opening by pushing a screwdriver through the slot on the front of the door
plate. Press near the top or bottom of the section and the tabs that hold it in
place will break free. Attach the camera to the mount so that the cone of the
camera points through the opening. Adjust the camera to the desired position
and secure it in place by tightening the screw on the mount.
This door intercom product consists of two sub assemblies which must be
attached to each other before the final assembly can be installed. In this
guide the electronic sub assembly will be referred to as the “Companion
Board” and the mechanical assembly will be referred to as the “Door Plate.”
Review the following diagrams and assemble as shown.
Attaching the Companion Board
(IU-XXXXC)
Companion Board Connection Details
To Speaker
Microphone
(attached to back side)
Use D1 for Door1 chime sound
Use D2 for Door2 chime sound
Volume Adjustment
Companion Board
Microphone
Tube
Connect Intercom Hub here
(see following pages for details)
Bend mounting
tabs over to
secure the
Companion Board
Completed Sub-assembly
Attach button
and speaker
wires as shown
Align holes with
mounting tabs
Position the companion board onto the three mounting tabs as shown below.
The microphone attached to the back side of the companion board should
line up with the microphone tube on the bracket. Bend the mounting tabs to
secure the companion board. Connect the speaker and button wires by
sliding the small connector over the exposed pins on the companion board
as shown.
To Button
Remove this
section of screen
material
Attach camera to mount
using the screw provided
Attach pigtail
to rear of
camera
Completed Sub-assembly
(see Attaching the Companion Board)
Installation:
Install a compatible single-gang mounting box at the desired location.
h
Using a 2-conductor wire, connect the Telephone Entry Controller to
h
the empty screw terminal block on the IU (see diagram).
If necessary, attach the camera’s video output to a coax extension
h
that is long enough to reach your monitor or video distribution
equipment.
If necessary, cut the connector off of the end of the power supply and
h
splice in an extension using crimp-on connectors.
Channel Vision’s IU-0xxx does not come with a camera, but the IU-6xxx
Series door plate comes with a mini color camera which attaches to the
integrated camera mount. The IU-0xxx and IU-6xxx both interface with the
Channel Vision’s telephone entry controllers: TE110, C-0920, P-0920 and
P-0921 to provide audio and video communication with the front door.
Channel Vision Compatible (IU-xxxx)
Camera Power
To Monitor or
Video Distribution
Coax Extension
(not included)
BNC Video
Connector
2-Conductor Power
Supply Extension
(not included)
Strike
Active
Ring
Intercom
Active
12VAC
#
or
*
No CO
Strike
Time
3/5 rng
1
2
3
PowerIntercomUnlock
Door
Chime
CO Input
Phones
TELEPHONE ENTRY CONTROLLER
CO Input
Telephones
Model
P-0920
PRO
C H A N N E L
TM
V I S I O N
C H A N N E L
V I S I O N
TM
Connect to the
terminals marked
“TO SYS”
From Telephone
Service Provider
House
Telephones
12VAC
500mA
8
9
IU-xxxxC
500ft.
max
The diagram below shows how to connect the IU-xxxxC to Channel Vision’s
CAT5 Whole-House Intercom system. When the button is pressed on the
IU-xxxxC the ST-2000 Intercom Stations will generate a door chime.
Pressing Answer/End will open communication with the IU-xxxxC. Model
IU-6xxxC includes a color camera and IU-0xxxC includes no camera.
Channel Vision Compatible
(IU-xxxx )
CAT5 Intercom
C
P-0930
PRO
C H A N N E L
TM
V I S I O N
C H A N N E L
V I S I O N
TM
Model
P-0930
Whole-House Intercom
Page Out
Page Trigger
IR
Emitters
+15VDC
Power
Link
In
Link
Out
Hub
A
B
C
D
Room 1 Room 2
Room 3
Room 4 Room 5
Room 6
ST-2000
Press here to
answer door
These terminals can be
used to connect a ST-C5IDS
Door Strike Relay Module
Room 1
Room 2
Room 3
Room 4
Room 5
Room 6
Monitor
DND Answer/End
Page
Camera Power
To Monitor or
Video Distribution
Coax Extension
(not included)
BNC Video
Connector
2-Conductor power
Supply Extension
(not included)
Installation:
Install a compatible mounting box at the desired location.
h
Using CAT5 wire, connect the P-0930 to the 110 connector on the IU
h
(see diagram).
If necessary, attach the camera’s video output to a coax extension
h
that is long enough to reach your monitor or video distribution
equipment.
If necessary, cut the connector off of the end of the power supply and
h
splice in an extension using crimp-on connectors.
Installation:
Install a compatible single-gang mounting box at the desired location.
h
Using a 2-conductor wire, connect the Telephone Entry Controller to
h
the empty screw terminal block on the IU (see diagram).
If necessary, attach the camera’s video output to a coax extension
h
that is long enough to reach your monitor or video distribution
equipment.
If necessary, cut the connector off of the end of the power supply and
h
splice in an extension using crimp-on connectors.
Channel Vision’s IU-0xxx does not come with a camera, but the IU-6xxx
Series door plate comes with a mini color camera which attaches to the
integrated camera mount. The IU-0xxx and IU-6xxx both interface with the
Channel Vision’s telephone entry controllers: TE110, C-0920, P-0920 and
P-0921 to provide audio and video communication with the front door.
Channel Vision Compatible (IU-xxxx)
Camera Power
To Monitor or
Video Distribution
Coax Extension
(not included)
BNC Video
Connector
2-Conductor Power
Supply Extension
(not included)
Strike
Active
Ring
Intercom
Active
12VAC
#
or
*
No CO
Strike
Time
3/5 rng
1
2
3
PowerIntercomUnlock
Door
Chime
CO Input
Phones
TELEPHONE ENTRY CONTROLLER
CO Input
Telephones
Model
P-0920
PRO
C H A N N E L
TM
V I S I O N
C H A N N E L
V I S I O N
TM
Connect to the
terminals marked
“TO SYS”
From Telephone
Service Provider
House
Telephones
12VAC
500mA
8
9
IU-xxxxC
500ft.
max
The diagram below shows how to connect the IU-xxxxC to Channel Vision’s
CAT5 Whole-House Intercom system. When the button is pressed on the
IU-xxxxC the ST-2000 Intercom Stations will generate a door chime.
Pressing Answer/End will open communication with the IU-xxxxC. Model
IU-6xxxC includes a color camera and IU-0xxxC includes no camera.
Channel Vision Compatible
(IU-xxxx )
CAT5 Intercom
C
P-0930
PRO
C H A N N E L
TM
V I S I O N
C H A N N E L
V I S I O N
TM
Model
P-0930
Whole-House Intercom
Page Out
Page Trigger
IR
Emitters
+15VDC
Power
Link
In
Link
Out
Hub
A
B
C
D
Room 1 Room 2
Room 3
Room 4 Room 5
Room 6
ST-2000
Press here to
answer door
These terminals can be
used to connect a ST-C5IDS
Door Strike Relay Module
Room 1
Room 2
Room 3
Room 4
Room 5
Room 6
Monitor
DND Answer/End
Page
Camera Power
To Monitor or
Video Distribution
Coax Extension
(not included)
BNC Video
Connector
2-Conductor power
Supply Extension
(not included)
Installation:
Install a compatible mounting box at the desired location.
h
Using CAT5 wire, connect the P-0930 to the 110 connector on the IU
h
(see diagram).
If necessary, attach the camera’s video output to a coax extension
h
that is long enough to reach your monitor or video distribution
equipment.
If necessary, cut the connector off of the end of the power supply and
h
splice in an extension using crimp-on connectors.
Installation:
Install a compatible single-gang mounting box at the desired location.
h
Using a 2-conductor wire, connect the door phone output of your
h
Panasonic KSU to the empty screw terminal block on the IU (see
diagram).
Consult your Panasonic manual for instructions regarding door phone
h
operation.
If necessary, attach the camera’s video output to a coax extension that is
h
long enough to reach your monitor or video distribution equipment.
If necessary, cut the connector off of the end of the power supply and
h
splice in an extension using crimp-on connectors.
Channel Vision's IU Panasonic Series models are a compatible replacement
for the Panasonic KXT30865. These 1/4" solid brass door plates provide an
attractive alternative to the standard plastic door station sold by Panasonic.
This product interfaces with Panasonic’s KSU phone systems to provide
communication with the front door. Model IU-6xxxP includes a color camera
and IU-0xxxP includes no camera.
®
Panasonic Compatible (IU-xxxxP)
Camera Power
To Monitor or
Video Distribution
Coax Extension
(not included)
BNC Video
Connector
2-Conductor Power
Supply Extension
(not included)
Connect to the
terminals marked
“TO SYS”
From Telephone
Service Provider
System Phones
Panasonic
KSU
1640ft. max
(22AWG)
10
11
Installation:
Install a compatible single-gang mounting box at the desired location.
h
Using a 2-conductor wire, connect the door phone output of your
h
Panasonic KSU to the power module, then connect the screw terminals
on the power module to the screw terminals on the IU station (see
diagram).
Consult your Panasonic manual for instructions regarding door phone
h
operation.
Channel Vision's IU-0xxxP8 Series models are a compatible replacement for
the Panasonic KXT7775 which provides the amplified communication needed
to work with newer Panasonic phone systems. These 1/4" solid brass door
plates provide an attractive alternative to the plastic door station sold by
Panasonic. This product interfaces with Panasonic’s KSU phone systems to
provide communication with the front door. There is no color camera option
available for this model.
®
Panasonic Compatible Amplified
(IU-0xxxP8)
From Telephone
Service Provider
System
Phones
Power
Supply
(included)
Power
Module
(included)
Use
Center pins
(Pins 3 &4)
No Connection
To
Door Station
Card
Panasonic
KSU
Installation:
Install a compatible single-gang mounting box at the desired location.
h
Using a 2-conductor wire, connect the door phone output of your
h
Panasonic KSU to the empty screw terminal block on the IU (see
diagram).
Consult your Panasonic manual for instructions regarding door phone
h
operation.
If necessary, attach the camera’s video output to a coax extension that is
h
long enough to reach your monitor or video distribution equipment.
If necessary, cut the connector off of the end of the power supply and
h
splice in an extension using crimp-on connectors.
Channel Vision's IU Panasonic Series models are a compatible replacement
for the Panasonic KXT30865. These 1/4" solid brass door plates provide an
attractive alternative to the standard plastic door station sold by Panasonic.
This product interfaces with Panasonic’s KSU phone systems to provide
communication with the front door. Model IU-6xxxP includes a color camera
and IU-0xxxP includes no camera.
®
Panasonic Compatible (IU-xxxxP)
Camera Power
To Monitor or
Video Distribution
Coax Extension
(not included)
BNC Video
Connector
2-Conductor Power
Supply Extension
(not included)
Connect to the
terminals marked
“TO SYS”
From Telephone
Service Provider
System Phones
ana
cP
soni
UKS
1640ft. max
(22AWG)
10
11
Installation:
Install a compatible single-gang mounting box at the desired location.
h
Using a 2-conductor wire, connect the door phone output of your
h
Panasonic KSU to the power module, then connect the screw terminals
on the power module to the screw terminals on the IU station (see
diagram).
Consult your Panasonic manual for instructions regarding door phone
h
operation.
Channel Vision's IU-0xxxP8 Series models are a compatible replacement for
the Panasonic KXT7775 which provides the amplified communication needed
to work with newer Panasonic phone systems. These 1/4" solid brass door
plates provide an attractive alternative to the plastic door station sold by
Panasonic. This product interfaces with Panasonic’s KSU phone systems to
provide communication with the front door. There is no color camera option
available for this model.
®
Panasonic Compatible Amplified
(IU-0xxxP8)
From Telephone
Service Provider
System
Phones
Power
Supply
(included)
Power
Module
(included)
Use
Center pins
(Pins 3 &4)
No Connection
To
Door Station
Card
Panasonic
KSU
500-091 rev C
www.chann e l v i s i o n . c o m
234 Fischer Avenue, Costa Mesa, California 92626 USA
(714)424-6500 (800)840-0288 (714)424-6510 fax
Channel Vision Technology will repair or replace any defect in material or workmanship which
occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for
one year from the date of original purchase. This is a no hassle warranty with no mail in
warranty card needed. This warranty does not cover damages in shipment, failures caused by
other products not supplied by Channel Vision Technology, or failures due to accident, misuse,
abuse, or alteration of the equipment. This warranty is extended only to the original purchaser,
and a purchase receipt, invoice, or other proof of original purchase date will be required before
warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling (800) 840-0288 toll free.
A Return Authorization number must be obtained in advance and can be marked on the outside
of the shipping carton.
This warranty gives you specific legal rights and you may have other rights (which vary from
state to state). If a problem with this product develops during or after the warranty period,
please contact Channel Vision Technology, your dealer or any factory-authorized service
center.
Channel Vision products are not intended for use in medical, lifesaving, life sustaining or
critical environment applications. Channel Vision customers using or selling Channel Vision
products for use in such applications do so at their own risk and agree to fully indemnify
Channel Vision for any damages resulting from such improper use or sale.
1
Specifications:
Speaker Size (mm): 40
Depth (in): .73
Impedance: 8 Ohms
Power Peak (W): 0.2
Frequency Range: 500 Hz - 3.5 kHz
Dimensions:
IU-Series plate only: 4.5” (L) x 3.75” (W) x .25” (D)
IU-Series assembly: 4.5” (L) x 3.75” (W) x 1.75” (D)
Color Camera: (IU-6xxx, IU-6xxxC, & IU-6xxxP only)
Camera Lens: 4.3mm
Resolution: 550 lines
S/N Ratio: More than 48 dB
Min Illumination: 0.2 LUX @ F2.0
Power Consumption: 12VDC, 65mA
Video Output: 1 Vp-p @ 75 ohms
Operating Temp: -10°C to 50°C (14°F to 122°F)
Specifications subject to change without notice.
Speaker
Speaker
Speaker
Speaker
Electronic Shutter: 1/60s - 1/100,000s
Iris Control: Automatic
White Balance: Automatic
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Black Box TE110A User manual

Category
Holders
Type
User manual
This manual is also suitable for

Black Box TE110A is a compact and versatile telephone entry controller that provides secure communication between a visitor at the door and occupants inside the building. It features a built-in keypad for easy access control, allowing authorized individuals to enter the premises using a personalized code. Additionally, it supports two-way audio and video communication, enabling occupants to see and speak with visitors before granting access.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI