1 of 7
ISSUED: 05-25-10 SHEET #:125-9113-2 08-19-10
Model: HLGP432-C450-SM, HLGP432-C450-SM-Q10
Installation and Assembly:
Desktop Swivel Mount
A
B
C
D
E
NOTE: Read entire instruction sheet before you start installation and assembly.
Before you start make sure all parts listed are included with your product.
F
G
H
I
J
K L
M
HLGP432-C450-SM HLGP432-C450-SM-Q10
Description Qty Part # Qty Part #
A
swivel plate assembly 1 090-1965 10 090-1965
B 10-32 x 3/8 flat head screw 4 560-2742 40 560-2742
C krazy glue 1 600-0152 4 600-0152
D 10-32 brass insert 4 560-0758 40 560-0758
E 1/4-20 x 1 3/4" elevator bolt 2 560-1764 20 560-1764
F 1/4-20 slope nut 3 530-0035 23 530-0035
G adhesive tape 4 570-0046 40 570-0046
H M5 x 6 mm phillips type-F screw 2 520-9504 20 520-9504
I plastic cap 2
590-1294
20
590-1294
J #8 split lock washer 4 540-2044 40 540-2044
K M4 flat washer 4 540-2081 40 540-2081
L M4 x 16 mm socket pin serrated washer head screw 2 510-1087 20 510-1087
M M4 x 12 mm socket pin screw 2 520-1079 20 520-1079
N 4 mm allen wrench 1 560-9646 3 560-9646
O
M4 x 16 phillips pan trilobe screw 2 520-2621 20 520-2621
Parts List
N
O
2 of 7
ISSUED: 05-25-10 SHEET #:125-9113-2 08-19-10
Secure four 10-32 brass inserts (D) into bottom of display base stand using Krazy Glue (C).
NOTE: Do not apply and extensive amount of glue on 10-32 brass inserts (D) or fasteners
will be difcult to fasten. Krazy Glue must be applied as shown in g. 1.1.
After applying glue, 10-32 brass inserts (D) must be fully seated into holes in the display base stand.
NOTE: Installer must allow Krazy Glue (C) a minimum of 15 minutes to dry prior to installation on the
swivel plate assembly (A).
1
D
NOTE: Display stand and mounting
hole locations may appear different than
illustrated.
Mounting to Desktop Surface
Mounting using Bolt Down Method
Skip to Pages 3 and 4 Steps 2-5
Mounting using Glue Down Method
Skip to Pages 5 and 6 Steps 6-9
Attaching Inserts to Display Base Stand
C
D
.09"
FIG 1.1
FIG 1.2
BOTTOM OF DISPLAY BASE STAND
3 of 7
ISSUED: 05-25-10 SHEET #:125-9113-2 08-19-10
Use swivel plate assembly (A) as a template to mark location of holes, point 1 and point 2, approximately 6" apart
on table. Drill two holes using a 1/4'' drill bit.
Place two 1/4-20 x 1 3/4" elevator bolts (E) into slots on swivel plate assembly (A).
SHOWN WITH 30° OF SWIVEL
AS AN EXAMPLE
H
A
3
POINT 1 POINT 2
TABLE TOP
6"
(152 mm)
2
E
90°
90°
60°
30°
60°
30°
Choose swivel range below and identify swivel
range holes.
Insert using two screws (H) into swivel range holes
of swivel plate assembly (A) as shown below.
SWIVEL RANGE HOLE
Mounting using Bolt Down Method
4 of 7
ISSUED: 05-25-10 SHEET #:125-9113-2 08-19-10
Hand tighten slope nut (F) through 1/4-20 x 1 3/4" elevator bolt (E) until snug against bottom of desktop surface.
Thread another slope nut (F) upside-down, about two turns from rst slope nut (F). Insert an open box wrench
between both slope nuts (F) and tighten. NOTE: Avoid jamming both slope nuts (F) together, doing so may make it
difcult to remove slope nut used for tightening rst slope nut (F). After slope nut is secure remove bottom slope nut
and add plastic cap (I) as shown in gure 5.2. Repeat with remaining 1/4-20 x 1 3/4" elevator bolt (E).
Skip to step 9 page 7.
Detail 1
TIGHTENING
SLOPE NUT
4
B
26" Display Base Stand Attachment Location
(note orientation of plate to base stand)
BOTTOM OF DESKTOP
FIG 5.1 FIG 5.2
E
F
E
5
I
Secure swivel plate assembly (A) to bottom of display base stand using four at head screws (B) in 26" or 32"
orientation.
FRONT
FRONT
NOTE: Do not overtighten slope nut (F)
plate may distort
32" Display Base Stand Attachment Location
(note orientation of plate to base stand)
5 of 7
ISSUED: 05-25-10 SHEET #:125-9113-2 08-19-10
Secure swivel plate assembly (A) to bottom of display stand using four at head screws (B) in 26" or 32"
orientation.
7
6
B
FRONT
FRONT
90°
H
A
60°
30°
90°
60°
30°
SHOWN WITH 30° OF SWIVEL
AS AN EXAMPLE
Choose swivel range below and identify swivel
range holes.
Insert using two screws (H) into swivel range holes
of swivel plate assembly (A) as shown below.
SWIVEL RANGE HOLE
26" Display Base Stand Attachment Location
(note orientation of plate to base stand)
32" Display Base Stand Attachment Location
(note orientation of plate to base stand)
Mounting using Glue Down Method
6 of 7
ISSUED: 05-25-10 SHEET #:125-9113-2 08-19-10
8
DISPLAY BASE STAND
DRIED 3M RUBBER
AND VINYL #80 SPRAY
ADHESIVE (not supplied)
DESK SURFACE
NOTE: Display base stand may appear
different than illustrated.
A
G
Clean bottom of swivel plate assembly (A) with rubbing alcohol. Spray bottom of swivel plate assembly (A) only
where tape will be applied, with 3M rubber and vinyl #80 spray adhesive (not supplied). Wait at least 4 minutes
to dry before applying adhesive strip (H). Pull apart the four adhesive strips (H) and apply to bottom of swivel
plate assembly (A).
Clean desk surface with rubbing alcohol. Use 3M rubber and vinyl #80 spray adhesive (not supplied) on the
mounting surface area only. NOTE: Spray adhesive will not remove easily. Wait at least 4 minutes to dry before
removing red tape backing from adhesive strips on swivel plate assembly (A). Place swivel plate assembly (A) rmly
on surface. NOTE: There is a recommended 72 hour cure time for tape on swivel plate assembly (A).
NOTE: Once tape backing is removed be careful not to touch the sticky surface of the tape with ngers, as this can
cause the tape to lose some of its holding power.
NOTE: After application of tape on swivel plate assembly (A), the bond strength will increase as the adhesive ows
onto the surface.
At room temperature, approximately 50%
of the ultimate strength will be achieved
after 20 minutes, 90% after 24 hours,
and 100% after 72 hours. In some cases,
bond strength can be achieved more quickly
by exposure to elevated temperatures
(e.g. 150°F [66°C] for 1 hour).
Mounting using Glue Down Method
7 of 7
ISSUED: 05-25-10 SHEET #:125-9113-2 08-19-10
9
g 9.1
g 9.2
O
DISPLAY
DISPLAY
DISPLAY BASE STAND
NOTE: Display and base stand may appear
different than illustrated
NOTE: Screws are installed at a diagonal.
Installation of Security Screws for Base to Display Attachment
J
K
M or L
Thread two M4 x 16 phillips pan trilobe screws (O) to top left and bottom right attachment holes as shown in g.
9.1. Remove the two M4 x 16 phillips pan trilobe screws (O) and attach display to base stand using two M4 x 16
mm socket pin serrated washer head screws (L) or M4 x 12 mm socket pin screws (M), #8 split lock washers (J),
and M4 at washers (K).
NOTE: Use screws supplied with the display as a length reference when choosing screws (M or L).
Tighten with 4 mm security allen wrench (N). Use TV supplied screws for remaining holes.
© 2010, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
/
