Atdec Telehook ProAV TH-PPA-18-25 Installation guide

Type
Installation guide

Atdec Telehook ProAV TH-PPA-18-25 offers adjustable projector pole accessory, supporting a maximum load of 1000lbs. It allows for flexible configurations with a range of 18" to 25" in length, providing various mounting options for projectors. Easily assemble your desired length using the included components and secure the position with the provided screws. The cable cover keeps cables organized and protected.

Atdec Telehook ProAV TH-PPA-18-25 offers adjustable projector pole accessory, supporting a maximum load of 1000lbs. It allows for flexible configurations with a range of 18" to 25" in length, providing various mounting options for projectors. Easily assemble your desired length using the included components and secure the position with the provided screws. The cable cover keeps cables organized and protected.

Step 2. Configurations
TH-PPA-18-25
Component Checklist
18-25” (457-635mm) Adjustable Projector Pole Accessory
! IMPORTANT - Install Telehook Adjuster Pole as per installation instruction.
! This product supports a maximum load of 454Kg (1000lbs.).
! The manufacturer accepts no responsibility for incorrect installation.
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received all parts against the component checklist and hardware above.
Adjuster Pole
Plastic Cover
HARDWARE
Security Set Screw
(x2)
Set Screw
(x2)
Standard Socket Pan Head
Screw (x1)
4mm Security Allen Key
Security Socket Pan Head
Screw (x1)
Adjustor Pole
Extension Pole
Existing Ceiling
Plate Bracket.
(Sold seperately
and available from
ATDEC.)
2.5mm Allen Key
2.1. Configure components as per image below for a pole length of
18”.
2.2. Screw Extension Pole in a clockwise direction into Ceiling Plate
Bracket.
Extension Pole
2.3. Configure components as per
image below for a pole length range of
20-25”.
2.4. Screw Extension Pole in a
clockwise direction into Ceiling Plate
Bracket.
2.5. Locate Adjuster pole on extension
Pole aligning the holes with the slot.
Adjustor Pole
18” Range 20-25” Range
Existing Ceiling
Plate Bracket
Extension Pole
Slot
Holes
Installation Instructions
Step 3. Assemble to desired length
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 22.05.13 ©
Upper Hole
3.2. Insert the one Standard or Security Socket Head Pan Screw through the slot
in the Adjuster Pole into either of the 2 visible holes in the Extension Pole. Each
hole enables a different length range.
Step 4. Secure Position
4.1. When desired pole length has been selected use either the
Security or Set Standard Screws to secure position. Tighten with the
2.5mm Security Allen Key supplied.
4.2. Snap off bottom segment of cable cover for cable access.
Lower Hole
3.3. Move the extension pole to the desired length and rotate to locate in one of
the three slots. Adjust the tightness of the screw using the 4mm Security Allen Key
supplied.
20”
22”
24”
21”
23”
25”
Cable
Snap off
Installation Instructions
  • Page 1 1
  • Page 2 2

Atdec Telehook ProAV TH-PPA-18-25 Installation guide

Type
Installation guide

Atdec Telehook ProAV TH-PPA-18-25 offers adjustable projector pole accessory, supporting a maximum load of 1000lbs. It allows for flexible configurations with a range of 18" to 25" in length, providing various mounting options for projectors. Easily assemble your desired length using the included components and secure the position with the provided screws. The cable cover keeps cables organized and protected.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI