TH-TVCH
Component Checklist
Mobile TV Cart / Heavy Duty
Column
Base
Castors (x4)
Tilt adjustment
Spanner (x2)
Castor Spanner
Mounting
Brackets (x2)
Mounting Bracket
Extensions (x4)
250mm
Uprights (L) & (R)
Upright Bottom
Extension (x2)
260mm
Upright Top
Extension (x2)
Mounting BracketColumn BottomColumn Top
M4 x 16/25
(x8)
M5 Washers
(x8)
1/4” Washers
(x6)
M5 x 16/25
(x8)
M6 x 20/40/55
(x6)
M8 x 20/40/55
(x6)
Cable Plug (x4)
93mm OD
Washer (x2)
Rectangular Washer
(x4)
28mm OD Spacer (x8)
21mm OD black
Washer (x16)
M8 Phillps Head Screw
(x16)
3/8” Washer (x2)
3/8” Spring
Washer (x2)
3/8” Bolt (x2)
M8 Button Head
Screw (x6)
M8 Spring Washer
(x6)
Allen Key
Spacers (x12)
Socket Head Bolt
(x4)
21mm OD Silver
Washer (x2)
HARDWARE
! IMPORTANT - Install TV Cart as per installation instruction.
! This product supports a maximum load of 125kg (275lbs.).
! This product supports VESA Mounting Hole Configurations: From 200mm to 450mm wide (800mm with extensions)
and from 200mm to 450mm high (800mm high with extensions).
! The manufacturer accepts no responsibility for incorrect installation.
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received against the component checklist and hardware above.
Step 2. Assemble Base
2.1 Mount all castors and tighten with caster spanner.
Castor Spanner
Tools Required:
• Phillips Head Screwdriver
Installation Instructions
Step 3. Mount Column to Base
Step 6. Choose Screen Orientation
Step 4. Adjust Height Step 5. Attach Uprights
3.1 Line holes up
and secure column
to base.
3.2 Secure column
from beneath.
M8 Button Head Screws
3/8” Spring Washer
3/8” Washer
93mm OD Washer
3/8” Bolt
Spanner
M8 Spring Washers
Holes
6.1 The TV Cart supports both Landscape and Portrait orientations. The method of attaching
the screen will depend on the screen’s VESA hole configuration.
Before moving to the next step, measure dimensions X & Y as shown below.
4.1 You can adjust the
height by moving the
tubes up or down before
fastening them.
M8 Screws
M8 Curved Washer
Allen Key
Allen Key
Landscape
Portrait
VESA hole configuration
X
X
YY
5.1 Remove fasteners and washers from the Column before attaching
Uprights. Secure fasteners loosely to allow for movement.
M8 Curved
Washer
M8 Button
Head Screw
Step 7. Attach Fixings to Screen
If dimension Y is from 200mm to 450mm skip Step 8 and go straight to Step 9
If dimension X is 200mm
Insert Socket Head Bolt
straight into the screen
ensuring that there is a
3-5mm gap.
3-5mm
3-5mm
Screen back
M4/5/6/8
Screw
Spacer
M5 or 1/4”
Washer
If dimension X is from
300mm to 450mm
If dimension X is from
450mm to 800mm
If dimension Y is from
450mm to 800mm
mount the Upright
extensions.
Mount the Brackets onto
the back taking note to
leave the bottom bracket
loose so that it can slide.
Mount the Brackets with
extensions onto the back
taking note to leave the
bottom bracket loose
so that it can slide.
M8 Phillips Head Screw
21mm OD M8
Flat Washer
Rectangular Washer
Extension Bracket
Step 8. Mount Upright Extensions
3-5mm
M8 Phillips
Head Screw
NOTE: Key holes
are on top, slots
are at the bottom.
21mm OD
Black Washer
28mm OD Spacer
Extension Bracket
LOOSEN
TIGHTEN
TIGHTEN
Installation Complete
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 1.
11.13 ©
Step 9. Mount Screen
Step 10. Adjust Tilt Step 11. Cable management
Cable Caps
Routing Options
9.1 Align top
Socket Head bolts
to upright holes.
Socket Head Bolt
M8 Button
Head Screws
& Washers
21mm OD
Silver washer
Allen Key
Uprights
Top mounting Bracket
9.2 Insert bolts through key holes and lower
to secure.
10.1 Using the provided
spanners to adjust tilt, hold
down the nut on the inside of the
upright whilst turning the bolt on
the outside.
Hold Tighten|Loosen
9.3 Insert the remaining socket head bolts
and washers on to the bottom bracket before
fastening all of the screws.
/
