Kallista P34008-00-AD Installation guide

Kallista
Brand
Kallista
Model
P34008-00-AD
Category
Wall & ceiling mounts accessories
Type
Installation guide

This manual is also suitable for

INSTALLATION INSTRUCTIONS
Bathroom Accessories
1048647-2-B
1 of 5
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
P34001, P34002, P34003,
P34006, P34008, P34010
INSTALLATION INSTRUCTIONS
Bathroom Accessories
1048647-2-B
2 of 5
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
THANK YOU FOR CHOOSING KALLISTA
We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual
before you install your KALLISTA product. If you encounter any installation or performance problems, please do
not hesitate to contact us at the phone number listed at the bottom of the page.
BEFORE YOU BEGIN
CAUTION: Risk of personal injury. These products are not designed or intended for use as a grab bar or
support bar. Do not install these products in any area where they are likely to be used inadvertently as a
grab bar or support bar.
These products should be located and mounted to a wall stud. While it is possible to mount them to any
surface, a stud-mounted product will yield the best results.
Use a level to ensure that the center lines for the wall plates are vertical where applicable and the post
center lines are horizontal where applicable.
Observe all local plumbing and building codes..
KALLISTA reserves the right to make revisions in the design of products without notice, as specifi ed in the
Price Book.
TOOLS AND MATERIALS
Assorted
Screwdrivers
Level Pencil Tape
Measure
Assorted
Hex Wrenches
Claw
Hammer
Drill with 5/16"
(8 mm) Bit
INSTALLATION INSTRUCTIONS
Bathroom Accessories
1048647-2-B
3 of 5
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
WALL PLATE INSTALLATION
5/8"
(16 mm)
Center
Point
Mounting
Hole
Mounting
Screws
Wall Plate
Anchors
Pilot Holes
Nail
Determine the desired mounting location.
Mark the vertical and horizontal centerlines for the accessory to be installed. Consult the roughing-in sheet
to determine the dimensions.
When installing multiple-post accessories, determine the required distance between the center points.
Use a level to ensure that center points for multiple-post accessories are horizontally level.
Mark the pilot hole locations vertically 5/8” (16 mm) above and below each center point. Vertically line up
the holes on each wall plate.
Select a drill and bit that are appropriate for the wall material you will be drilling through. Carefully drill a
5/16” (8 mm) hole at all marked pilot hole locations.
NOTE: If you encounter a stud during drilling, stop immediately and use only the mounting screws.
Install the anchors as illustrated above.
Use two mounting screws to secure the wall plate to the wall.
INSTALLATION INSTRUCTIONS
Bathroom Accessories
1048647-2-B
4 of 5
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
TOWEL BAR INSTALLATION
Setscrew
Setscrew
Mount the wall plates to the wall in the desired location.
Place both ends of the towel bar over the wall plates.
Tighten the setscrews to hold the towel bar in place.
ROBE HOOK AND TOWEL RING INSTALLATION
Setscrew
Mount the wall plate to the wall in the desired location.
Place the end of the robe hook or towel ring over the wall plate.
Tighten the setscrew to hold the robe hook or towel ring in place.
INSTALLATION INSTRUCTIONS
Bathroom Accessories
1048647-2-B
5 of 5
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
TISSUE HOLDER INSTALLATION
3-1/2"
(89 mm)
Pilot Holes
Back
Plate
Tissue Rod
Setscrew
Skirt
Back Plate
Mounting Screws
Anchors
Nail
Determine the desired mounting location.
Mark the pilot hole locations vertically 3-1/2” (89 mm) apart.
Select a drill and bit that are appropriate for the wall material you will be drilling through. Carefully drill a
5/16” (8 mm) hole at all marked pilot hole locations.
NOTE: If you encounter a stud during drilling, stop immediately and use only the mounting screws.
Install the anchors as illustrated above.
Use two mounting screws to secure the back plate to the wall.
Install the skirt and tissue rod over the post on the back plate.
Tighten the setscrew to hold the tissue rod in place.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Kallista P34008-00-AD Installation guide

Kallista
Brand
Kallista
Model
P34008-00-AD
Category
Wall & ceiling mounts accessories
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents