Cabletron Systems Netlink FRX4000 User manual

NetView Service Point

on

SmartSwitch 1800, FRX4000,

FRX6000, and Frame Relay Module

Supplemental Software

User Guide

09-41-06-092-03

The Complete Networking Solution

TM

Supplemental Software User’s Guide iii

Cabletron Systems reserves the right to make changes in specifications and other information

contained in this document without prior notice. The reader should in all cases consult

Cabletron Systems to determine whether any such changes have been made.

The hardware, firmware, and/or software described in this manual is subject to change without

notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL,

INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER

(INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR

RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF

CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE

KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

States of America.

VxWorks is a copyright of Wind River Systems, Inc.

California, Berkeley, and its contributors. IP software is provided by the regents and contrib-

utors “as is” and any express or implied warranties, including, but not limited to, the implied

warranties of merchantability and fitness for a particular purpose, are disclaimed. In no event

shall the regents or contributors be liable for any direct, indirect, incidental, special, exem-

plary, or consequential damages (including, but not limited to, procurement of substitute goods

or services; loss of use, data, or profits; or business interruption) however caused and on any

theory of liability, whether in contract, strict liability, or tort (including negligence or oth-

erwise) arising in any way out of the use of this software, even if advised of the possibility of

such damage.

Gateway Daemon (GateD) software, Release 3.5.5, is maintained and developed by Cornell

University and its collaborators. The version of GateD used with this Cabletron product has

been modified.

Netlink is a trademark of Cabletron Systems, Inc. All other product designations are the

property of their respective owners.

About This Manual

Rev Date Reason for Update

01 June 1996 Initial release of document

02 February 1997 Product name change

03 March 1998 Product name change

This manual describes how to access the NetView Service Point function in a SmartSwitch

1800, 9W004, FRX4000, or FRX6000 from a NetView host. It is assumed that the user has a

working knowledge of NetView, so this document does not attempt to explain how to use

NetView.

Related Documents

These appropriate product-specific user guide(s) can be ordered from Cabletron Systems:

●

SmartSwitch 1800 Release 4.0 User Guide, Cabletron number 09-44-06-018.

●

9W004 Release 4.0 User Guide, Cabletron number 09-41-06-169.

●

Netlink FRX4000 & FRX6000 Release 4.0 User Guide, Cabletron number

09-41-06-162.

iv NetView Service Point

Supplemental Software User Guide 1

Introduction

NetView support in Cabletron frame relay access products provides manager access

to downstream SDLC devices, and allows the manager to diagnose problems and

change parameters in the node to overcome some problems.

The NetView host (focal point) sends commands to the service point in the form of

NMVTs (network management vector transports). The service point function trans-

lates information from the node into NMVTs and responds to the host.

The various user guides (FRX4000/6000, SmartSwitch 1800, and Frame Relay

Module) describes the NetView function in the related products. The remainder of this

document describes the supported operations on the NetView host.

Installing the Cabletron Supplemental Software

It is strongly recommended that the software be installed by

someone familiar with NetView.

To install the Cabletron software into the host device, follow this procedure:

1. Upload the binary/EBCDIC files (all files without filename extensions) from the

PC to a temporary or working Partitioned Data Set (PDS) on the host, as follows:

a. Insert the 3.5" (DOS) NetView diskette into the device and edit the file

SENDER.BAT, replacing the lowercase letters with values appropriate to your

configuration.

b. Log onto your target host and set it up for a file transfer.

c. Execute UPLOAD.BAT from the PC.

2. Edit Host PDS member "NSS" as follows:

a. Find the sample name "SAMPLE."

b. Enter the names (as known to VTAM) of the Network Management PUs that

identify each Netlink node to NetView.

c. Optionally, enter the Data Set Name to record configuration change requests.

3. Copy or move all members whose fourth character is a "U" or "V" to a NetView

Panel dataset. Copy or move all other members to a Clist dataset.

2 NetView Service Point

Operation

To invoke the program, enter

NSS

from the NCCF. This will display a screen similar

to the following:

Figure 1 Main Status Panel

Data Displayed

Service Point Name

Status

– is the status (active or inactive) of the PU.

Prod Type

– will always be

OLX

.

Software Version

– is the current version of the Cabletron software.

Config Name

– is always

OLXCONF

.

Last Loaded

– is the time of the last IPL.

Function Key Operations

Pressing one of the function keys listed below will perform the appropriate operation:

[PF1] Help

– will display a "road map" of the panels (screens), shown in

Figure 2.

[PF3] End

– will exit to the NCCF (NetView Controls Command Facility).

[PF7]

,

[PF8] Pg_up,Pg_down

– will scroll the screen up or down if there is more

information to display.

[PF11] Rfsh

– will re-display the screen with updated values.

SDLC Internetwork Status Panel

PF 1-Help 3-End 4-Ln Status 5-Frm Rly 6-Cfg 7-Pg u p 8-Pg dn 9-Restart 11-Rfsh

R-S Service Prod Software Con fig Last Load ed

Poin t Name Status Type Version Name Date Time

BD0N VSP ACTIV OLX 3200 OLXCONF 11Feb1998 17:45

BD1N VSP I NACT

BD2N VSP ACTIV OLX 3200 OLXCONF 12Feb1998 08:52

Supplemental Software User Guide 3

Moving the cursor to an entry under

Service Point Name

(in Figure 1) and pressing

[PF4]

(

Ln_Status

) will display a line status screen for that service point, as described

under "Line Status Panel."

Help Panel

Figure 2 On-Line Help Panel

Line Status Panel

Figure 3 Line Status Panel

PU Status Panel

Hardware Config Panel

PD Stats

Main Statu s Panel

RT and SYS LOGs

Frame Relay

FR C onfi g

PU Config

Line S tatus Pan el

Line Stats Line Config

Service Point: BD0NVSP SDLC Line Status Panel Version: 3200

PF 1-Help 2-Exit 3-End 4-PU Status 5-Line Stats 6-Config 7-Act 8-Deact 10-Disp

Line Actual Des ired

Name Status Status Port In terface DTR DSR CTS DCD

LINE11 ACTIV ACTIV 0/0 RLP/960 ON ON ON OFF

LINE12 ACTIV ACTIV 0/1 RLP/960 ON ON ON ON

4 NetView Service Point

Data Displayed

Line Name

– is the Name configured on the first screen of the Cabletron device SNA

Port record, or if that parameter is not configured, the Name in the NetView Param-

eters part of the Network Defaults record.

Actual Status

– is the current status (active or inactive) of the line.

Desired Status

– matches the Blocked Port Flag (N = active, Y = inactive) configured

on the first screen of the SNA Port record.

Port

– is the RLP and port that defines the line.

Interface

– is always

RLP/960

.

DTR/DSR/CTS/DCD

– are the current states (On, Off) of the modem signals on the line.

Function Key Operations

Pressing one of the function keys listed below will perform the appropriate operation

from the Line Status panel:

[PF1] Help

– will display the Help panel (Figure 2).

[PF3] End

– will return you to the Main Status panel (Figure 1).

Moving the cursor to an entry under Line Name and pressing a supported function key

gives you these additional options:

[PF4] PU_Status

– will display the PU Status panel for that line, as described

under "PU Status Panel" later.

[PF6] Config

– will display a screen of parameters for that line, and allow you

to change the values of some parameters. See "Line Configuration

Panel" later.

[PF7] Act

– will activate the line.

[PF8] Deact

– will de-activate the line.

Supplemental Software User Guide 5

PU Status Panel

Figure 4 PU Status Panel

Data Displayed

PU Name

– is the PU Name configured in the Cabletron device SNA Port record.

SDLC Actual Status

– is the current status (active or inactive) of the PU.

Desired Status

– is the Istatus (active or inactive) configured on the PU parameters

screen of the SNA Port record.

POLL ADDR

– is the Local SAP Address configured on the LLC2 Parameters screen

of the SNA Port record.

LLC2 Actual Status

– is the current status (active or inactive) of the LLC2 session.

LANCON Status

– is not applicable. (This is from part of the software that is shared

with Netlink's SDLC Link Server.)

MAC Address

– is the Local MAC Address configured on the LLC2 Parameters screen

of the SNA Port record.

XID

– is the ID created from IDBLK and IDNUM in the SNA Port record.

Function Key Operations

Pressing one of the function keys listed below will perform the appropriate operation

from the PU Status panel:

[PF1] Help

– will display the Help panel (Figure 2).

[PF3] End

– will return you to the Line Status panel (Figure 3).

Service Point: BD0NVSP PU Status Panel Version: 3200|

Line name: LINE4

PF 1-Help 2-Exit 3-End 4-PU Stats 6-Con fig 7-A ct 8-Deact 10-Display 11-Refresh

SDLC LLC2

PU Ac tua l De si re d PO L L Ac tua l LANCO N

Name Status Status ADD R Status Statu s MAC Address XID

PUC3 ACTIV ACT I V C3 ACT I V ACT IV F F FF F FF F DCE3 00 D CE 30 1

6 NetView Service Point

Moving the cursor to an entry under PU Name and pressing a supported function key

gives you these additional options:

[PF6] Config

– will display a screen of parameters for that line, and allow you

to change the values of some parameters. See "Line Configuration

Panel" later.

[PF7] Act

– will activate the line.

[PF8] Deact

– will de-activate the line.

Line Configuration Panel

Figure 5 Line Configuration Panel

Configurable Parameters

ISTATUS

will cause the line to be enabled (if

ACT

) or disabled (if

INACT

) the next time the node

undergoes IPL. The line will remain in that state until either an on-line port disable or

enable is performed on the Cabletron device (as described in the User Guide) or a

VARY INACT

or

VARY ACT

is sent from the NetVIEW manager.

NRZI

is the inverse of the parameter NRZ in the SNA Port record in the Cabletron device.

The setting determines the level of data encoding:

No

= NRZ, which means that 1 represents high-level encoding and 0 is low-level.

Yes

= NRZI, which means that 1 represents no change in level and 0 is a change.

CLOCK

is equivalent to the Cabletron device parameter

Generate Clock

, which specifies

whether the port will generate the clock necessary to synchronize traffic over the link.

INTERNAL

= Yes,

EXTERNAL

= No.

Service Point: BD0NVSP SDLC Line Configuration Panel Version: 3200|

Line name: LINE11

Actual Status: ACTIV

Desired Status: ACTIV

PF 1-Help 2-Exit 3-End 4-PU Stats 6-Con fig 7-A ct 8-Deact 10-Display 11-Refresh

IST ATU S ACT ACTIVT O 10

NRZ I NO RCVCL O CK DT E

CLOCK EXTERNAL PAUSE 40

SPEED 9600 RETRIES 5

MAXIN 7 LPDATYPE 2

MAXOUT 7 LINKROLE PRIMARY

M O DULO 8

Supplemental Software User Guide 7

SPEED

is the line speed. Valid line speeds are:

75 150 300 600 1200

2400 4800 9600 14.4K 19.2K

24K 28.8K 38.4K 48K 56K

64K 72K 112K 128K 168K

192K 224K 256K 280K 320K

336K 384K 392K 448K 504K

512K 560K 576K 616K 640K

672K 704K 728K 768K 784K

832K 840K 896K 952K 960K

1.008M 1.024M 1.064M 1.088M 1.12M

1.152M 1.176M 1.216M 1.232M 1.28M

1.288M 1.344M 1.4M 1.408M 1.456M

1.472M 1.512M 1.536M 1.568M 1.6M

1.624M 1.664M 1.668M 1.728M 1.792M

1.856M 1.92M 1.984M 2.048M

ACTIVTO

is the activity timer (

Ti

).

RCVCLOCK

is equivalent to the Cabletron device parameter

Rcv Clock (TT) from DTE

, which allows

the clock to be looped back from the DTE using the terminal timing signal. Valid

values are

Y

and

N

.

PAUSE

is equivalent to the Cabletron device parameter

No Data Poll Period

, which is the time

between polls by the Cabletron device TPAD of its PU when the PU has no data to

send. Valid values are

0-125

(milliseconds).

RETRIES

is equivalent to the Cabletron device parameter

Maximum Retransmissions

, which is

the maximum number of times the SNA port will attempt to send a frame after expi-

ration of the

No Response Poll Period

. Valid values are

1-99

.

LPDATYPE

specifies the version of LPDA (1 or 2) that will be used.

Function Key Operations

Pressing one of the function keys listed below will perform the appropriate operation

from the Line Configuration panel:

[PF1] Help

– will display the Help panel (Figure 2).

[PF2] Exit

– will return you to the Line Status panel (Figure 3).

[PF3] End

– will ask whether you want to commit the changes, which will

update the Cabletron device database values. After you select

Yes

or

No

,

you will be returned to the Main Status panel (Figure 1).

8 NetView Service Point

Moving the cursor to a parameter and pressing a supported function key gives you

these additional options:

[PF6] Modify

– will allow you to change the configured values of the

parameter, if the parameter is displayed in green.

[PF7] Activate

– will activate the line.

[PF8] Deact

– will de-activate the line.

[PF10] Display

– will display output from the runcmd.

[PF11] Refresh

– will re-display the screen with updated values.

PU Configuration Panel

Figure 6 PU Configuration Panel

Configurable Parameters

ISTATUS

will cause the PU to be enabled (if

ACT

) or disabled (if

INACT

) the next time the line

is activated. The PU will remain in that state until either an on-line SDLC PU disable

or enable is performed on the Cabletron device (as described in the User Guide) or a

VARY INACT

or

VARY ACT

is sent from the NetVIEW manager.

MAXDATA

is equivalent to the Cabletron device parameter

Maximum Bytes per Frame

. Valid

values are

25-4105

.

REPLYTO

is equivalent to the Cabletron device parameter

No Resp Poll Period

, which is the time

between polls by the TPAD port of its PU when the PU is not responding. The TPAD

will continue to poll at this interval up to the number of times specified by

RETRIES

Service Point: BD0NVSP PU Line Configuration Panel Version: 3200|

Line name: LINE11 PU Name: PUC3

Actual Status: ACTIV Desired Status: ACTIV

PF 1-Help 2-Exit 3-End 4-PD Stats 6-Modify 7-Act 8-Deact 10-D is play 11-Refresh

SDLC LLC2

SDLC Address C3 Response Timer (T1) 10

ISTATUS ACTIV Ack Timer (T2) 100

MAXDATA 265 Inactivity Timer (Ti) 30

MAX OU T See Li ne Con fig LANI N (N3) 001

MODULO See Line Con fig LANOUT (Tw) 001

DATMODE HALF retries (N2) 008

REPLY TO 1.0 Bandw id th Allocation (BAG) 00

RETRIES See Line Con fig

LPDS RESI D 80

AUTOCALL ENABLE Local SAP 04

Auto Retry Tout 60 Local MAC Address 4000000000C3

Auto Retry Ct 00 PU Type LLC2

Local S ub 1123

Remote Sub 2223

Supplemental Software User Guide 9

(Cabletron device parameter

Maximum Retransmissions

). Valid values are

40-9999

(milliseconds).

LPDARESID

is the LPDA Resource ID, which defines LUs on the PU. The value must match the

LOCADDR defined on VTAM. Valid values are

0-255

.

AUTOCALL

causes automatic calling between SNA ports when the controller becomes active. The

valid values are

ENABLE

and

DISABLE

.

Auto Retry Tout

is equivalent to the Cabletron device parameter

Autocall Retry Time

, which is the time

between autocall retries. Valid values are 15-255 (seconds).

Auto Retry Ct

is equivalent to the Cabletron device parameter

Autocall Retry Count

, which is the

maximum number of times an autocall will be sent. Valid values are

0-255

. Note that

a value of

0

allows indefinite retries.

Local Sub

is the subscriber address of the local (to the Cabletron device) end of an SNA con-

nection.

Remote Sub

is the address of the remote (to the Cabletron device) end of an SNA connection.

Response Timer (T1)

is used to detect the failure to receive a required acknowledgment or response from

the remote link station. The valid values are

0-250

(x 100 milliseconds).The link

station will start the timer when it transmits one of these:

●

an Information LPDU.

●

a Command LPDU with the P bit set to B'1.' (If this LPDU is sent while the timer

is already running, the link station will reset and restart it.)

The link station will reset T1 when it receives one of these:

●

A REJ LPDU, provided a Command LPDU with P bit set to B'1' is not out-

standing.

●

A Response LPDU with the F bit set to B '1.'

●

An Information or Supervisory LPDU with an N(R) greater than the last N(R)

received and less than or equal to the line station's V(S), provided a Command

LPDU with P bit set to B'1' is not outstanding.

If additional LPDUs are set from the remote link station after the local station has reset

T1, the timer will be restarted if acknowledgments of or responses to those LPDUs are

outstanding. If no acknowledgments/responses are outstanding, the link station will

start the inactivity timer. (See "Ti" later.)

If T1 expires and acknowledgments/responses are still outstanding, the link station

will send one of the following, then restart T1:

●

A Supervisory LPDU with the P bit set to B'1,' to solicit remote link station

status.

10 NetView Service Point

●

Any Unnumbered LPDUs that were not responded to the first time they were

sent.

If acknowledgments/responses are still outstanding after N2 tries (see that entry), the

link station will declare the link inoperative.

Ack Timer (T2)

is used by the link station to delay sending an acknowledgment of a received Infor-

mation LPDU. Valid values are

100-5000

(milliseconds).

The timer is started when the LPDU is received and reset when the acknowledgment

is sent. If the timer expires before the acknowledgment is sent, it must be sent as soon

as possible.

Inactivity Timer (Ti)

is used by the link station to detect an inoperative condition in either the remote link

station or the transmission medium. Valid values are

1-50

(seconds).

The timer will be started if T1 has been reset (for one of the reasons listed under "T1"

earlier), and additional LPDUs have been sent by the remote link station, and there are

no outstanding acknowledgments or responses from the local link station.

If the local station does not receive an LPDU before Ti expires, the station must send

an LPDU with the P bit set to B'1' to solicit the remote station's status. Recovery then

proceeds as described under "T1" earlier.

LANIN (N3)

is the number of Information LPDUs that will be received before sending an acknowl-

edgment. Valid values are

1-127

.

This parameter is used in conjunction with T2 to allow stations to reduce traffic. A

counter is initialized to N3, and will be decremented by one each time a valid

sequential Information LPDU is received. When the counter reaches

0

an acknowl-

edgment is sent.

N3 is reset whenever an Information or Supervisory acknowledgment LPDU is sent

by the local station.

LANOUT (Tw)

is the maximum number of sequentially numbered Information LPDUs that the link

station can have outstanding. Valid values are

1-127

.

Retries (N2)

is the maximum number of times that an LPDU (including Information LPDUs resent

after a checkpoint operation) will be sent following expiration of T1. Valid values are

0-255

.

Bandwidth Allocation (BAG)

assigns the host to one of sixteen groups whose parameters regulate bandwidth usage.

See "Bandwidth Allocation Groups" in the Cabletron device User Guide. Valid values

are

0-16

.

Local SAP

is the remote SAP address used to connect the PU to the host. This parameter is rel-

evant only in a connection to a 3174 or AS/400-type setup where a specific source

Supplemental Software User Guide 11

SAP address is required. If the LLC2 session will be run over a native LLC2 frame

relay interface, the parameter will be ignored.

Local MAC Address

identifies the PU to the host. Like the local SAP address, this parameter is relevant

only in a connection to a 3174 or AS/400-type setup where a specific source MAC

address is required. If the LLC2 session will be run over a native LLC2 frame relay

interface, the parameter will be ignored.

PU Type

is SDLC or LLC2.

Function Key Operations

Pressing one of the function keys listed below will perform the appropriate operation

from the PU Status panel:

[PF1] Help

– will display the Help panel (Figure 2).

[PF2] Exit

– will return you to the PU Status panel (Figure 4).

[PF3] End

– will ask whether you want to commit the changes, which will

update the Cabletron device database values. After you select

Yes

or

No

,

you will be returned to the Main Status panel (Figure 1).

Moving the cursor to a parameter and pressing a supported function key gives you

these additional options:

[PF6] Modify

– will allow you to change the configured values of the

parameter, if the parameter is displayed in green.

[PF7] Act

– will activate the line.

[PF8] Deact

– will de-activate the line.

[PF10] Display

– will display output from the runcmd.

[PF11] Refresh

– will re-display the screen with updated values.

12 NetView Service Point

Alerts

The Cabletron device will issue alerts (events) based upon NMVT protocols. The node

transparently passes all Alerts (Basic, Generic, RECFMS, etc.) received from down-

stream SNA/SDLC devices.

Host Alert ID Number

Each Alert generated by the Cabletron node appears in the event log identified by a

Netlink event number. The Alert is identified to the host console by an Alert ID

number. The following table cross-references each Alert ID number to the corre-

sponding event number that is used in this appendix.

Alert ID Number

Event Number Alert ID Number Event Number

X’0396D7BA’ 718 X'6279ADDE’ 721

X’0AECC2A6’ 713 X’6E0781DD’ 717

X’0E2DDF11’ 712 X’7F15E253’ 724

X’1103D152’ 709 X’83D91642’ 741

X’15C2CCE5’ 708 X’87180BF5’ 742

X’1C40F78B’ 710 X’8A5B2D2C’ 739

X’1D1B6697’ 722 X’8E9A309B’ 740

X’216D1033’ 745 X’A472BC48’ 714

X’25AC0D84’ 746 X’B1D9A4C5’ 737

X’28EF2B5D’ 743 X’B3B7D723’ 705

X’2C2E36EA’ 744 X’B776CA94’ 704

X’32A37F1B’ 701 X’BA35EC4D’ 707

X’32E516A1’ 761 X’BD84C4C9’ 702

X’34FFCB87’ 720 X’BEF4F1FA’ 706

X’3DCB0D63’ 715 X’C08037D8’ 759

X’480F6C65’ 762 X’E65B0B7F’ 738

X’548CB735’ 723 X’EABB6A14’ 711

X’5A44BB82’ 760 X’EE849C82’ 725

X’5B8F5BA7’ 736

Supplemental Software User Guide 13

Alerts

701

Event Log Message puname/linename – SDLC Link Stn Not Responding

Host Console Message LINK ERROR:SDLC COMMUNICATIONS/REMOTE NODE

Alert Condition An SDLC logical link has been lost. The secondary link station does

not respond to poll frames sent by the primary station.

Alert ID Number X'32A37F1B’

Alert Type X'01’ Permanent

Alert Description X'3300’ Link Error

Probable Causes X'2104'

X'2031’

SDLC communications/remote node

Line

User Causes X'0209’ Remote device power off

Actions X'0200’ Check power

Install Causes (none)

Failure Causes

X'2104'

X'3511'

X'F017’

SDLC communications/remote node

Line

Poll count exhausted

Actions (Sender-specific actions)

Additional SVs X'52'SV

X’02'SF

X’04'SF

X'06'SF

X'07'SF

X'8C'SV

X’01'SF

X'02'SF

X'03'SF

X'04'SF

X'05'SF

X'06'SF

X'07'SF

X'08'SF

X'05'SV

X'10'SF

LCS Configuration

Remote Device Address

Local Device Address

Link Station Attributes

Link Attributes

Link Station Data

Current Ns/Nr Counts

Outstanding Frame Count

Last Control Field Received

Last Control Field Sent

Sequence Number Modulus

Link Station State

LLC Reply Timer Expiration Count

Last Received Nr Count

Hierarchy/Resource List

Hierarchy Name List

First resource below sender:

Resource Name = (LINE NAME)

Resource Type = X'3D'(LINE)

Second resource below sender:

Resource Name = (Physical Unit Name)

Resource Type = X'80'(Physical Unit)

14 NetView Service Point

702

Event Log Message puname/linename – SDLC Link Stn Sent DM

Host Console Message LINK ERROR:SDLC COMMUNICATIONS

Alert Condition An SDLC logical link has been lost. The secondary link station sent a

Disconnect Mode response to the primary station.

Alert ID Number X'BD84C4C9’

Alert Type X'01’ Permanent

Alert Description X'3300’ Link Error

Probable Causes X'2004' SDLC communications

User Causes (none)

Install Causes (none)

Failure Causes X'2004'

X'F01A’

SDLC communications

DM received

Actions (Sender-specific actions)

Additional SVs X'52'SV

X’02'SF

X’04'SF

X'06'SF

X'07'SF

X'8C'SV

X’01'SF

X'02'SF

X'03'SF

X'04'SF

X'05'SF

X'06'SF

X'07'SF

X'08'SF

X'05'SV

X'10'SF

LCS Configuration

Remote Device Address

Local Device Address

Link Station Attributes

Link Attributes

Link Station Data

Current Ns/Nr Counts

Outstanding Frame Count

Last Control Field Received

Last Control Field Sent

Sequence Number Modulus

Link Station State

LLC Reply Timer Expiration Count

Last Received Nr Count

Hierarchy/Resource List

Hierarchy Name List

First resource below sender:

Resource Name = (LINE NAME)

Resource Type = X'3D'(LINE)

Second resource below sender:

Resource Name = (Physical Unit Name)

Resource Type = X'80'(Physical Unit)

Supplemental Software User Guide 15

704

Event Log Message puname/linename – SDLC Link Stn rcvd FRMR - Inv. cmd

Host Console Message SOFTWARE PROGRAM ERROR:SDLC COMMUNICATIONS

Alert Condition An SDLC logical link has been lost. The primary link station sent an invalid or unsup-

ported command to the secondary link station. The secondary link station responded

with a Frame reject.

Alert ID Number X'B776CA94’

Alert Ty pe X '01 ’ Permanent

Alert Description X'2100’ Software Program Error

Probabl e Causes

X'2004'

X'1000'

SDLC communications

Software program

User Causes (none)

Install Causes (none)

Failure Causes X'1000'

X'F010’

Software program

Frame reject received: invalid/unsupported command or response sent

Actions (Sender-specific actions)

Additional SVs X'52'SV

X’02'SF

X’04'SF

X'06'SF

X'07'SF

X'8C'SV

X’01'SF

X'02'SF

X'03'SF

X'04'SF

X'05'SF

X'06'SF

X'07'SF

X'08'SF

X'05'SV

X'10'SF

LCS Configuration

Remote Device Address

Local Device Address

Link Station Attributes

Link Attributes

Link Station Data

Current Ns/Nr Counts

Outstanding Frame Count

Last Control Field Received

Last Control Field Sent

Sequence Number Modulus

Link Station State

LLC Reply Timer Expiration Count

Last Received Nr Count

Hierarchy/Resource List

Hierarchy Name List

First resource below sender:

Resource Name = (LINE NAME)

Resource Type = X'3D'(LINE)

Second resource below sender:

Resource Name = (Physical Unit Name)

Resource Type = X'80'(Physical Unit)

16 NetView Service Point

705

Event Log Message puname/linename – SDLC Stn rcvd FRMR - IFLD Invalid

Host Console Message SOFTWARE PROGRAM ERROR:SDLC COMMUNICATIONS

Alert Condition An SDLC logical link has been lost. The primary link station sent an i-field when not per-

mitted to the secondary link station. The secondary link station responded with a Frame

reject.

Alert ID Number X'B3B7D723’

Alert Type X'01’ Permanent

Alert Description X'2100’ Software Program Error

Probable Causes

X'2004'

X'1000'

SDLC communications

Software program

User Causes (none)

Install Causes (none)

Failure Causes X'1000'

X'F011’

Software program

Frame reject received: i-field sent when not permitted

Actions (Sender-specific actions)

Additional SVs X'52'SV

X’ 02'S F

X’ 04'S F

X'06'SF

X'07'SF

X'8C'SV

X’ 01'S F

X'02'SF

X'03'SF

X'04'SF

X'05'SF

X'06'SF

X'07'SF

X'08'SF

X'05'SV

X'10'SF

LCS Configuration

Remote Device Address

Local Device Address

Link Station Attributes

Link Attributes

Link Station Data

Current Ns/Nr Counts

Outstanding Frame Count

Last Control Field Received

Last Control Field Sent

Sequence Number Modulus

Link Station State

LLC Reply Timer Expiration Count

Last Received Nr Count

Hierarchy/Resource List

Hierarchy Name List

First resource below sender:

Resource Name = (LINE NAME)

Resource Type = X'3D'(LINE)

Second resource below sender:

Resource Name = (Physical Unit Name)

Resource Type = X'80'(Physical Unit)

Page is loading ...

Cabletron Systems Netlink FRX4000 User manual

This manual is also suitable for

Cabletron Systems Netlink FRX4000 User manual

Related papers

Other documents