Wacker Neuson PDT2B User manual

Page is loading ...

BELGIE

1730 ASSE-MOLLEM ASSESTEENWEG 17 Tel. (32) 02-4528509+07

4040 Herstal 4 Avenue

9800 Deinze Kortrijkse Steenweg 400 Tel. (09)-386 8529

B - 6041 Gosselies Rue Adrienne Bolland s/n Tel. 071-372450

ÇESKÁ REPUBLIKA

19402 PRAHA 9-HLOUBETIN KOLBENOVA 259 Tel. (0042) 2 862165

DANMARK

2690 KARLSLUNDE RØRGANGEN 6 Tel. 46 15 36 00

8200 Arhus N Randersvej 346 Tel. 86-231777

5250 Odense SV Holkebjergvej 56A Tel. 66-172170

ESPAÑA

28850 TORREJON DE ARDOZ (MADRID) POLIGONO INDUSTRIAL LAS MONJAS Tel. (34) 91-6757525 / 85

CALLE PRIMAVERA 11

08780 PALLEJA (Barcelona) PRAT DE LA RIBA, 184 Tel. (93)-6632273

41700 Dos Hermanas (Sevilla) Poligono Industrial La Palmera Tel. (95)-4691129

Nave 14 Tel. (95)-4691129

46133 Meliana (Valencia) Calle Salvador Giner, 6 Tel. (96)-1492102

15890 Santiago de Compostela (La Coruña) Poligono Industrial el Tambre, Via Pasteur, 47a Tel. (981) 573366 / 67

SUOMI

FIN 04250 KERAVA Peltomäenkatu 7 Tel. (358) 9-274 4740

FRANCE

77170 BRIE COMTE ROBERT 335, RUE GLORIETTE—ZAC DU TUBOEUF Tel. (33) 1-60623000

Aix en Provence 13540 Puyricard Tel. 4 42630526

Arras 62217 Beaurains Tel. 3 21235361

Bordeaux 33700 Merignac Tel. 5 56343346

Bourges 18390 St. Germain du Puy Tel. 2 48652015

Lyon 69740 Genas Tel. 4 78401384

Nancy 54180 Heillecourt Tel. 3 83565801

Rennes 35510 Cesson Sevigne Tel. 2 99321522

Toulouse 31270 Cugnaux Tel. 5 61075250

Kehl 77694 Kehl-Goldscheuer Tel. (0590) 9321

HUNGARIA

1106 BUDAPEST Kada u. 137 Tel. (36) 1-260 8668

IRELAND

DUBLIN 13 127A. BALDOYLE INDUSTRIAL ESTATE Tel. (00353) 01-8320218

ITALIA

40016 SAN GIORGIO DI PIANO (Bologna) Via Due Agosto, 1980, Strage di Bologna, 3 Tel. 39.05.665.566 - 665.1574

00125 ACILIA (Roma) Viale Enrico Ortolani, 262 Tel. 39 . 06 . 5219246

20041 Agrate Brianza (Mi) Via Archimede, 31 Tel. 39. 039.699 0136

NEDERLAND

3821 BJ AMERSFOORT COBOLWEG 1 Tel. 033 - 450 40 45

2984 BL Ridderker Glasblazerstraat 7 Tel. 0180 - 41 70 56

7418 EZ Deventer Arnbergstraat 9 Tel. 0570 - 63 00 87

5684 PS Best De Dintel 37 Tel. 0499 - 33 04 33

1704 RT Heerhugowaard Einsteinstraat 4d Tel. 072 - 574 20 78

9411 XN Beilen De Hanekampen 19 Tel. 0593 - 52 31 24

NORGE

1481 HAGAN TYRIVN. 7 Tel. (47) 0 6707-2330

POLSKA

05850 OŻARÓW MAZOWIECKI UL. KONOTOPSKA 4 Tel. (48) 22 722 20 59

62081 Wysogotowo k. Poznania ul. Kamienna 1 Tel. (061) 8143797

PORTUGAL

2785-S. Domingos De Rana Urbanização Industrial de Trajouce, Lote 1 Tel. (351) 21 4443561 / 87

4785-S. Romao do Coronado Lg. do Soeiro, Apartado 2 Tel. (351) 22 982 7992 / 93

SVERIGE

24734 SÖDRA SANDBY SKATTEBERGAVÄGEN 13 Tel. (46) 046-57870

16170 Bromma Karlsbodavägen 17E Tel. 08-282860

41749 Göteborg Knipplekullen 3A Tel. 031-551362

SCHWEIZ

8305 Dietlikon Bahnhofstrasse 3 Tel. (41) 1-8353939

TURKIYE

81120 K. Bakkalköy-ISTANBUL Karaman Çiftligi Cad. No: 55 Tel. (90) 216 573 0621

35350 Üçkuyular-Izmir Mithatpasa Cad. No. 1189 Tel. (90) 232 259 8944

Ostim 06370 Ankara Alinteri Bulvari No. 210 Tel. (90) 312 385 6438/6439

Information Contained In This Manual

This manual provides information and procedures to safely operate and maintain the WACKER Model PD 2B

Pump.

For your own safety and protection from physical injury, carefully read, understand, and observe the safety

instructions described in this manual. Always operate and maintain this machine in accordance with the

instructions described in this manual. A well-maintained piece of equipment will provide many years of trouble-

free operation.

This manual is divided into the sections listed below.

PD 2B FOREWORD

THE INFORMATION CONTAINED IN THIS MANUAL WAS BASED ON MACHINES IN PRODUCTION AT THE TIME OF PUBLICATION.

WACKER CORPORATION RESERVES THE RIGHT TO CHANGE ANY PORTION OF THIS INFORMATION WITHOUT NOTICE.

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

! !

1012SD26

Keep this manual or a copy of it with the machine. If manual becomes lost

or additional copies are desired, please contact WACKER Corporation.

This manual covers machines with Serial Numbers beginning:

PDT 2B - 7612, 7613

PDI 2B - 7626

1A Operation

(English)

1B Operation

(German)

1C Operation

(Spanish)

1D Operation

(French)

2 Pump

(English, German, Spanish, French)

3 Engine

(English, German, Spanish, French)

HEAD (MAX.)

CAPACITY (MAX.)

PUMP SPEED

ENGINE SPEED

ENGINE POWER

25 ft

60 gpm

60 spm

3000 rpm

3.5 HP

SERIAL NO.:

WACKER CORPORATION

MENOMONEE FALLS, WI., USA 53052

MADE IN U.S.A.

PD 2B

SIZE

2

IN.

DIAPHRAGM PUMP

FOREWORD PD 2B

Identification Plate

An identification plate listing the model number and serial number is attached to each unit and is located on the

pump cover. This plate should not be removed.

Please record the information found on this plate so it will be available should the identification plate become

lost or damaged. When ordering parts or requesting service information, you will always be asked to specify the

model and serial number of the unit.

761201234

7612 01234

Production Sequence

Model Identification

Serial Number

The serial number found on the identification plate is a

nine- digit number. The first four digits identify the specific

machine model (Bill of Material). The last five numbers

indicate the production sequence for that model.

The serial number identifies your machine and will

ensure that you receive the correct replacement parts.

1010SD51

Page is loading ...

1A-1

PD 2B

Operating Information

1A

Table of Contents

1.1 Safety Notes.................................................................................... 1A-2

1.2 Laws Pertaining to Spark Arresters ................................................. 1A-2

1.3 Operating Safety ............................................................................. 1A-2

1.4 Engine Safety .................................................................................. 1A-3

1.5 Service Safety ................................................................................. 1A-3

1.6 Dimensions...................................................................................... 1A-4

1.7 Technical Data ................................................................................ 1A-5

1.8 Application ....................................................................................... 1A-6

1.9 Recommended Fuel ........................................................................ 1A-6

1.10 Priming Pump.................................................................................. 1A-6

1.11 Before Starting ................................................................................ 1A-6

1.12 To Start ........................................................................................... 1A-7

1.13 To Stop............................................................................................ 1A-7

1.14 Operation......................................................................................... 1A-7

1.15 Hoses and Clamps .......................................................................... 1A-8

1.16 Accessories ..................................................................................... 1A-8

1.17 Periodic Maintenance Schedule ...................................................... 1A-9

1.18 Changing Engine Oil........................................................................ 1A-9

1.19 Servicing Air Cleaner..................................................................... 1A-10

1.20 Spark Plug..................................................................................... 1A-10

1.21 Gear Case ..................................................................................... 1A-11

1.22 Connecting Rod Bearing................................................................ 1A-11

1.23 Cleaning Pump .............................................................................. 1A-11

1.24 Carburetor Adjustment .................................................................. 1A-12

1.25 Setting Engine Speed.................................................................... 1A-12

1.26 Storage.......................................................................................... 1A-13

1.27 Transporting .................................................................................. 1A-13

1.28 Recommended Spare Parts .......................................................... 1A-13

1.29 Troubleshooting............................................................................. 1A-14

Keep this manual or a copy of it with the machine. If you lose this

manual or need an additional copy, please contact WACKER Corpo-

ration.

This machine is built with user safety in mind; however, it can

present hazards if improperly operated and serviced. Follow operat-

ing instructions carefully! If you have questions about operating or

servicing this equipment, please contact WACKER Corporation.

1A OPERATION PD 2B 1

1A-2

1.1 Safety Notes

This manual contains NOTES, CAUTIONS, and WARNINGS which must be followed to prevent the possibility of

improper service, damage to the equipment, or personal injury.

Note:

Contains additional information important to a procedure.

CAUTION: Provides information important to prevent errors which could damage machine or components.

WARNING

Warns of conditions or practices which could lead to personal injury or death!

1.3 Operating Safety

Familiarity and proper training are required for the safe operation of equipment! Equipment operated improperly or

by untrained personnel can be dangerous! Read the operating instructions contained in this manual and the

engine manual to familiarize yourself with the location and proper use of all controls.

1.2 Laws Pertaining to Spark Arresters

Notice: State Health Safety Codes and Public Resources Codes specify that in certain locations spark arresters be

used on internal combustion engines that use hydrocarbon fuels. A spark arrester is a device designed to prevent

accidental discharge of sparks or flames from the engine exhaust. Spark arresters are qualified and rated by the United

States Forest Service for this purpose.

In order to comply with local laws regarding spark arresters, consult the engine distributor or the local Health and Safety

Administrator.

WARNING

NEVER allow improperly trained people to oper-

ate this equipment. People operating this equip-

ment must be familiar with the potential risks and

hazards associated with it.

NEVER touch engine or muffler while pump is

operating or immediately after it has been turned

off. These areas get hot and may cause burns.

NEVER use accessories or attachments which

are not recommended by WACKER for this

equipment. Damage to equipment and/or injury

to user may result.

NEVER pump volatile, flammable or low flash

point fluids. These fluids could ignite or explode.

NEVER pump corrosive chemicals or water con-

taining toxic substances. These fluids could

create serious health and environmental haz-

ards. Contact local authorities for assistance.

ALWAYS read, understand, and follow proce-

dures in Operator’s Manual before attempting

to operate equipment.

ALWAYS be sure operator is familiar with proper

safety precautions and operation techniques

before using pump.

ALWAYS be sure pump is on a firm, level surface

and will not tip, roll, slide, or fall while operating.

ALWAYS close fuel valve on engines equipped

with one, when pump is not being operated.

ALWAYS store equipment properly when it is not

being used. Equipment should be stored in a

clean, dry location out of the reach of children.

PD 2B OPERATION 1A

1A-3

1.4 Engine Safety

Internal combustion engines present special hazards during operation and fueling! Failure to follow the safety

guidelines described below could result in severe injury or death.

WARNING

ALWAYS refill fuel tank in well-ventilated area.

ALWAYS replace fuel tank cap after refueling.

DO NOT smoke while operating pump.

DO NOT smoke when refueling engine.

DO NOT refuel hot or running engine.

DO NOT refuel engine near open flame.

DO NOT spill fuel when refueling engine.

DO NOT operate near open flames.

1.5 Service Safety

Poorly maintained equipment can become a safety hazard! In order for the equipment to operate safely and properly

over a long period of time, periodic maintenance and occasional repairs are necessary.

WARNING

DO NOT attempt to clean or service pump while

it is running. Rotating parts can cause severe

injury.

DO NOT crank a flooded engine with the

spark plug removed on gasoline powered

engines. Fuel trapped in the cylinder will

squirt out the spark plug opening.

DO NOT test for spark on gasoline-powered

engines, if engine is flooded or the smell of

gasoline is present. A stray spark could ignite

fumes.

DO NOT use gasoline or other types of fuels

or flammable solvents to clean parts in

enclosed areas. Fumes from fuels and

solvents can accumulate and become

explosive.

ALWAYS operate pump with all safety devices

and guards in place and in working order.

ALWAYS keep area around muffler free of debris

such as leaves, paper, cartons, etc. A hot muffler

could ignite them, starting a fire.

ALWAYS replace worn or damaged compo-

nents with spare parts designed and recom-

mended by WACKER for servicing this ma-

chine.

ALWAYS remove or disconnect spark plug on

pumps equipped with gasoline engines, before

servicing pump, to avoid accidental start-up.

Page is loading ...

PD 2B OPERATION 1A

1A-5

Engine Make Briggs & Stratton

Engine Model 91232

Rated Power

Hp (kW) 3.5 (2.6)

Spark Plug type Champion RJ19LM

Electrode Gap in. (mm) 0.030 (0.76)

Engine speed rpm 3000 ± 100

Air Cleaner

type Dual element

Engine Lubrication

1

oil grade SAE 30W - service class SG, SF, SE

Engine Oil Capacity oz. (ml) 20 (600)

Fuel type Regular unleaded gasoline

Fuel Tank Capacity qts. (l) 3.0 (2.8)

1.7 Technical Data

Engine

Weight lbs. (kg) 112 (51)

Max. Suction Lift

2

ft. (m) 25 (7.5)

Max. Discharge Head ft. (m) 25 (7.5)

Max. Total Head ft. (m) 50 (15)

Max. Discharge gpm (m

3

h) 60 (13.7)

Gear Case Lubrication oil grade SAE 30

oz. (ml) 20 (600)

Suction / Discharge Dia. in. (mm) 2 (50)

Maximum Solid Size in. (mm) 1.25 (32)

Pump

1 At temperatures below 40° F (5° C) use SAE 10W30.

2 Based on pump operating at sea level. Maximum suction lift will be less at higher altitudes.

The required sound specifications, per Appendix 1, Paragraph 1.7.4.f of the EC-Machine Regulations, are:

- the sound pressure level at operator’s location (L

pA

) = 79 dB(A)

- the sound power level (L

WA

) = 90 dB(A)

These sound values were determined according to ISO 3744 for the sound power level (L

WA

) and ISO 6081 for

the sound pressure level (L

pA

) at the operator’s location.

The sound measurements were obtained with the unit operating on pavement at nominal speed.

Sound Measurements

1A OPERATION PD 2B 1

1A-6

1.8 Application

This pump is intended for removing clean water or water

containing a large amount of debris and suspended

solids.The model PD 2B can pump water containing

solids up to 1.25" (32 mm) diameter.

Diaphragm pumps are ideal for pumping mud, slurries

and seepage. Typical applications include dewatering of

trenches, sewers, pipelines, septic tanks, holding tanks,

farm ponds, fields and excavations where a large amount

of solids may be present in the water.

1.11 Before Starting

1. Read safety instructions at the beginning of manual.

2. Place pump as near to water as possible, on a firm,

flat, level surface.

3. Check that hoses are securely attached to pump.

Suction hose

(c) must not have any air leaks. Check

that all hose clamps (b) and couplings (a) are tight.

Check that cap on surge chamber

(f) is tight.

4. Check that discharge hose (e) is not blocked. Lay

hose out as straight as possible. Remove any twists

or sharp bends from hose which may block the flow

of water.

Note:

Operating the pump with any part of the

discharge line positioned higher than 25' (7.5 m)

above the pump can cause backflow into the pump

and damage pump components.

5. Make sure suction strainer (d) is clean and securely

attached to end of hose. The strainer is designed to

protect the pump by preventing large objects from

being pulled into the pump.

Position strainer so it will remain under water as water

level drops.

6. Check fuel level, engine oil level, and condition of air

cleaner.

1.9 Recommended Fuel

The engine requires regular grade unleaded gasoline.

Use only fresh, clean gasoline. Gasoline containing

water or dirt will damage fuel system.

1.10 Priming Pump

Diaphragm pumps are self priming and seldom need to

have water added to them before starting. However, if

the pump has not been used for several weeks and the

rubber valves inside it are dry, adding water through the

surge chamber (f) will help the valves seal and shorten

the amount of time required for the pump to prime.

e

a

c

b

a

b

d

f

1010SD45

PD 2B OPERATION 1A

1A-7

O F F

I D L E F A S T

F A S T C H O K E

O F F

I D L E F A S T

R U N

C H O K E

i

h

2

h

1

g

1

g

2

1011SD87

1.12 To Start

1. If engine is cold, move choke lever to “CHOKE”position

(g

1

). If engine is hot, set choke to “RUN” position

(g

2

).

2. Open throttle by moving throttle control all the way to

the right (h

1

).

3. Pull starter rope (i). Repeat if necessary until engine

starts.

4. After engine is started and has warmed up move

choke lever to “RUN” (g

2

).

If engine does not start refer to the Engine Manufacturer’s

Owner’s Manual.

1.14 Operation

Run engine at full speed while operating pump.

Pump should begin pumping water within a minute

depending on length of suction hose and height of pump

above water. Longer hoses will require more time.

If pump does not prime, check for loose fittings or air leak

in suction hose. Make sure strainer in water is not

blocked.

WARNING

1.13 To Stop

To stop engine, move throttle control to “OFF” (h

2

).

DO NOT pump flammable fluids, fuels, corrosive

chemicals, or fluids containing toxic substances.

These fluids can create potentially dangerous health

and environmental hazards. Contact local authori-

ties for assistance.

1A OPERATION PD 2B 1

1A-8

1.15 Hoses and Clamps

Suction hoses (a) must be rigid enough not to collapse

when pump is operating.

Discharge hoses (b) are usually thin-walled collapsible

hoses. Rigid hoses similar to those used as suction

hoses may also be used as discharge hoses.

Note:

Suction and discharge hoses are available from

WACKER. Contact your nearest dealer for more infor-

mation.

Two clamps (c) are recommended for connection of

suction hoses to inlet coupling.

Note:

This connection is important. Even a small air leak

on the suction side of pump will prevent the pump from

priming.

For other hose connections, one T-bolt or worm-gear

type clamp is usually sufficient to hold hoses in place. In

some cases, slight variances in hose diameters may

make it necessary to add more clamps in order to

maintain tight connections.

b

a

c

1010SD46

1.16 Accessories

WACKER offers a complete line of fittings, hoses, and

clamps to properly connect the pump to match various

job conditions. Refer to the Parts Lists in Section 2 of this

manual for a complete list of accessories.

PD 2B OPERATION 1A

1A-9

1.17 Periodic Maintenance Schedule

The chart below lists basic pump and engine maintenance. Refer to engine manufacturer’s Operation Manual for

additional information on engine maintenance.

Daily After Every Every Every

before first 50 hrs 100 hrs. year

starting 5 or

hours 300 hrs.

Check fuel level.

Check engine oil level.

Inspect air filter. Replace as needed.

Check and tighten external hardware.

Change engine oil.

Check oil level in pump gear case.

Grease pump connecting rod bearing.

Clean engine cooling fins

Check and clean spark plug.

Replace in-line fuel filter.

Change oil in pump gear case.

Clean carbon deposits from cylinder head.

1.18 Changing Engine Oil

Drain oil while engine is still warm.

1. Remove oil fill cap (d) and oil drain plug (e) to drain

oil.

2. Replace drain plug and fill engine crankcase with

clean oil until it is level with fill plug opening (f).

Oil Capacity - 20 oz. (600 ml), SAE 30W

e

d

1001SD25

f

1A OPERATION PD 2B 1

1A-10

1.19 Servicing Air Cleaner

Service air cleaner frequently to prevent carburetor mal-

function.

NEVER run engine without air cleaner. Severe engine

damage will occur.

NEVER use gasoline or other types of low flash point

solvents for cleaning the air cleaner. A fire or explosion

could result.

The engine is equipped with a dual element air cleaner.

1. Loosen air cleaner cover screws

(a). Remove cover

and air cleaner assembly carefully to prevent dirt from

falling into carburetor.

2. Pre-cleaner

(b)

Wash in solution of mild detergent and warm water.

Rinse thoroughly in clean water. Squeeze dry in a

clean cloth and let dry.

Soak element in clean engine oil and squeeze in clean

absorbant cloth to remove ALL EXCESS oil.

3. Paper Cartridge (c)

Tap element lightly to remove excess dirt. If very dirty

or damaged replace it. Do not oil cartridge.

Note:

Do not use pressurized air or petroleum sol-

vents such as kerosene to clean cartridge. They will

cause cartridge to deteriorate.

4. Re-install cartridge and precleaner.

5. Replace cover and tighten screws securely.

1.20 Spark Plug

Clean or replace spark plug as needed to ensure proper

operation. Wait until engine cools before removing spark

plug. Refer to the engine Owner’s Manual.

Spark Plug: Champion RJ19LM

CAUTION: A loose spark plug can become very hot and

may cause engine damage.

1006SD37

0.030 in.

(0.76 mm)

c

b

a

1011SD88

PD 2B OPERATION 1A

1A-11

1.21 Gear Case

Check the oil level in the gear case once a week or every

25 hours of operation.

Remove oil level plug

(e). Check that oil level is even

with plug opening. If oil level is low, add oil through the

top fill plug opening (d). Do not overfill.

Change oil in gear case once a year or every 300 hours

of operation.

Drain oil through drain plug opening

(f) at bottom of gear

case. Add oil through fill plug on top of gear case.

Oil capacity - 32 oz. (1000 ml) SAE 30

e

f

1.23 Cleaning Pump

When pumping heavy sludges or water containing large

amounts of dirt and solids, clean the pump often. If

allowed to sit in the pump and dry, these materials will

harden and could damage the valves or diaphragm

inside the pump the next time it is used.

When cleaning pump:

1. Pump clean water through pump for a few minutes

after each use to flush dirt from inside pump and

hoses.

2. Remove dirt from between engine cooling fins to

prevent them from clogging up. This will prevent

engine from overheating.

3. Remove front cover (g) and clean dirt and grease

build-up from connecting rod and inside of front pump

cover.

1010SD50

g

h

1010SD51

d

1.22 Connecting Rod Bearing

Gease connecting rod bearing once a week or every 25

hours of operation.

Use a hand operated grease gun. Add grease through

grease fitting located behind access hole (h) provided on

front cover.

1A OPERATION PD 2B 1

1A-12

1.24 Carburetor Adjustment

Minor carburetor adjustment may be required to com-

pensate for differences in fuel, temperature, altitude or

load. Air cleaner and air cleaner cover must be in place

when making adjustments.

Refer to the Engine Manufacturer's Owner's Manual or

contact an authorized WACKER Dealer when making

carburetor adjustments.

1.26 Storage

If pump is being stored for more than 30 days:

1. Clean pump as described under Section 1.23.

2. Drain out any water left in the pump housing.

3. Remove pump cover and clean inside of pump hous-

ing. Spray connecting rod and inside of pump cover

with a light film of oil.

4. Tape up suction and discharge ports to prevent

anything from falling into pump.

5. Change engine oil and follow procedures described in

engine manual for engine storage.

6. Cover pump and engine and store in a clean, dry area.

1.28 Recommended Spare Parts

Part Numbers appearing in Boldface type in the Parts

Section of this manual are recommended spare parts.

This means these parts are subject to wear under normal

operating conditions and may require periodic service or

replacement. It is recommended these items be stocked

to meet the expected service requirements of this model.

Actual stocking quantities of these and other parts used

in more extensive repairs will depend on the service

practices of each customer.

WACKER Corporation maintains a complete supply of

replacement parts. All service and repairs must be made

using quality WACKER service parts. Use of service

parts from sources other than those recommended by

WACKER could result in premature wear, product mal-

function, or bodily injury.

1.27 Transporting

WARNING

To avoid burns or fire hazards, let engine cool before

transporting pump or storing indoors.

Keep the engine level to prevent fuel from spilling.

1.25 Setting Engine Speed

Engine speed has been set to permit a top no-load speed

of 3000 rpm. Contact an authorized WACKER Dealer if

adjustment is necessary.

PD 2B OPERATION 1A

1A-13

1.29 Troubleshooting

Reason / Remedy

1. Engine problem. See engine manufacturer’s service manual

for troubleshooting and repair.

2. Engine oil level too low. Add oil to engine.

3. Pump housing filled with dirt and debris. Disassemble and

clean inside of pump.

4. Pump gear case damaged. Inspect and repair.

1. Pump is located too high above or too far away from water.

Locate pump closer to water.

2. Air leak on suction side of pump. Check that hose fittings and

cap on surge chamber are tight and sealing properly.

3. Suction hose damaged or collapsed. Repair or replace hose.

4. Strainer plugged. Clean or replace strainer.

5. Dirt collecting inside pump and hoses, blocking flow. Clean

inside of pump and flush hoses.

6. Engine running slow. Check engine speed and adjust. See

“Technical Data” for engine speed.

7. Pump valves damaged or not seating properly. Check for

stones and gravel imbedded in valves. Replace valves.

8. Diaphragm loose or damaged. Inspect diaphragm for damage.

Replace and tighten.

1. Pump located too high above or too far away from water.

Locate pump closer to water.

2. Suction strainer or intake line partially plugged. Clean hose line

and strainer.

3. Discharge hose is kinked or end is blocked. Check that hose

lies straight and flows freely.

4. Discharge hose too narrow. Use hose of equal diameter or

larger than suction hose.

Problem / Symptom

Engine does not start.

Engine starts but pump does not

take in water.

Pump output low.

Page is loading ...

2-1

2

PD 2B

Pump / Pumpe / Bomba / Pompe

2.1 Gearbox ......................................................................................2-2

2.2 Pump ..........................................................................................2-4

2.3 Labels .........................................................................................2-6

2-4 Accessories ................................................................................2-7

Page

Table of Contents

2.1 Getriebegehäuse ........................................................................2-2

2.2 Pumpe ........................................................................................2-4

2.3 Aufkleber.....................................................................................2-6

2-4 Sonderzubehör ...........................................................................2-7

Seite

Inhaltsverzeichnis

2.1 Caja de engranajes.....................................................................2-2

2.2 Bomba ........................................................................................2-4

2.3 Etiquetas.....................................................................................2-6

2-4 Accesorios ..................................................................................2-7

Página

Indice

2.1 Boîte de vitesses ........................................................................2-2

2.2 Pompe ........................................................................................2-4

2.3 Autocollants ................................................................................2-6

2-4 Accessoires ................................................................................2-7

Page

Table des Matières

BOMS 0007612, 0007613, 0007626

FROM MANUAL PART NO. 0089545-REV. B0998

2-2

2

PD 2B

1015SD56

2.1 Gearbox / Getriebegehäuse / Caja de engranajes / Boîte de vitesses

4

3

2

7

6

5

8

9

10

11

T1

12

15

14

11

13

14

28

26

25

24

23

T2

19

16

17

22

21

20

27

T3

1

18

T1 - 55-60 ft.lbs. (75-81 Nm)

T2 - 10-11 ft.lbs. (14-15 Nm)

T3 - 7-8 ft.lbs. (9.5-11 Nm)

29

2-3

2

PD 2B

1 0025690 Screw 1/2-13x2-1/2 Schraube Tornillo Vis 2

1 0025650 Washer-lock 1/2 Federring Disco de resorte Rondelle de ressort 2

2 0089212 Gearbox Getriebegehäuse Caja de engranajes Boîte de vitesses 1

3 0051324 Plug-oil 3/8-18 Schraubverschluß Tapón roscado Bouchon 1

4 0089213 Gasket-gearbox Dichtung Empaque Joint 1

5 0089214 Bearing-ball Kugellager Rodamiento de bolas Roulement à billes 1

6 0051333 Key-Woodruff Woodruffkeil Chaveta Woodruff Clavette Woodruff 2

7 0051332 Gear Zahnrad Engranaje Engrenage 1

8 0089215 Shaft-gear Welle Eje Arbre 1

9 0051338 Gear-int. Zahnrad Engranaje Engrenage 1

10 0089216 Gear-pinion Zahnrad Engranaje Engrenage 1

11 0089217 Bearing-ball Kugellager Rodamiento de bolas Roulement à billes 2

12 0025562 Screw 1/2-13x1-3/4 Schraube Tornillo Vis 2

12 0025650 Washer-lock 1/2 Federring Disco de resorte Rondelle de ressort 2

13 0089218 Bearing-ball Kugellager Rodamiento de bolas Roulement à billes 1

14 0051336 Pin-1/4x3/4, dowel Paßstift Espiga Cheville 2

15 0089219 Cover Deckel Tapa Couvercle 1

16 0089220 Hook-lifting Haken Gancho Croc 1

17 0051326 Screw 1/4x1-1/4 Schraube Tornillo Vis 2

17 0025647 Washer-lock 1/4 Federring Disco de resorte Rondelle de ressort 2

18 0087918 Key 3/16x1 Keil Chaveta Clavette 1

19 0025588 Screw 5/16-18x1 Schraube Tornillo Vis 4

19 - Washer-lock Federring Disco de resorte Rondelle de ressort 4

20 0089221 Adapter-engine Adapter Adaptador Raccord 1

21 0089222 O-Ring O-Ring Anillo-O Anneau-O 1

22 2001815 Retaining ring Sicherungsring Anillo de retención Bague d’arrêt 1

23 0072017 Screw 5/16-24x1 Schraube Tornillo Vis 4

23 0072699 Washer-lock Federring Disco de resorte Rondelle de ressort 4

24 0089223 Bearing-ball Kugellager Rodamiento de bolas Roulement à billes 1

25 0089224 Gear-pinion Zahnrad Engranaje Engrenage 1

26 0089225 Bearing-needle Nadellager Rodamiento de Roulement à 1

agujas aiguilles

27 - Plug-oil 1/8 NPT Schraubverschluß Tapón roscado Bouchon 2

28 0027675 Screw 1/4x1 Schraube Tornillo Vis 9

28 0025647 Washer-lock 1/4 Federring Disco de resorte Rondelle de ressort 9

29 0051306 Handle-towing pole Handgriff Manija Poignée 1

Ref. Part No. Description Beschreibung Descripción Description Qty.

2-4

2

PD 2B

1015SD57

43

30

29

44

2

3

4

5

6

4

1

9

10

46

11

12

14

15

13

12

14

15

7

3

8

18

16

17

13

27

T2

28

20

21

19

22

23

24

25

T3

34

35

36

37

38

39

40

41

42

32

33

36

38

39

T3

35

37

40

45

34

31

26

47

T2

26

T1

T1 - 55-60 ft.lbs. (75-81 Nm)

T2 - 35-40 ft.lbs. (48-54 Nm)

T3 - 16-20 ft.lbs. (22-27 Nm)

2.2 Pump / Pumpe / Bomba / Pompe

2-5

2

PD 2B

*Ref. PDT 2B PDI 2B

7612, 7613 7626

19 0074403 (right) -

0074404 (left) -

22 0074402 -

47 - 0089602

- 0089649 Engine Motor Motor Moteur 1

1 0054589 Cover-gearbox Deckel Tapa Couvercle 1

2 2005636 Fitting-grease Schmiernippel Grasera Graisseur 1

3 0051315 Screw #10-32x1/2 Schraube Tornillo Vis 6

4 0074395 Washer-retaining Scheibe Arandela Rondelle 2

5 0074396 Connecting rod Pleuel Biela Bielle 1

6 0074397 Bearing-cam follower Lager Rodamiento Roulement 1

7 0074399 Crank-arm Kurbel Manivela Manivelle 1

8 0089207 Seal-oil Öldichtung Empaque de aceite Joint d’huile 1

9 0051320 Screw 1/2x1-1/2 Schraube Tornillo Vis 1

10 0054829 Setscrew 5/16 Gewindestift Tornillo Vis 1

11 0025571 Screw 5/16-18x2 Schraube Tornillo Vis 2

12 0087972 Washer 5/16 Scheibe Arandela Rondelle 6

13 0080712 Shim-engine Ausgleichscheibe Laminilla Cale 8

14 0072699 Washer-lock 5/16 Federring Disco de resorte Rondelle de ressort 4

15 0025616 Nut 5/16-18 Mutter Tuerca Ecrou 4

16 0020487 Screw 5/16-18 x 2¼ Schraube Tornillo Vis 2

17 0051341 Bracket-bumper Konsole Ménsula Support 1

18 0025555 Screw Schraube Tornillo Vis 2

19 * Bracket Konsole Ménsula Support 1

20 0025649 Washer-lock Federring Disco de resorte Rondelle de ressort 2

21 0025617 Nut Mutter Tuerca Ecrou 2

22 * Axle Achse Eje Essieu 1

23 0051345 Wheel Rad Rueda Roue 2

24 0025640 Washer Scheibe Arandela Rondelle 2

25 0074393 Pin-cotter Sicherungssplint Clavija hendida Goupille fendue 2

26 0087715 Stud Gewindebolzen Perno prisionero Boulon 3

27 0051311 Screw 1/2x2-1/4 Schraube Tornillo Vis 4

28 0025707 Screw 10-14x1/2 Schraube Tornillo Vis 2

29 0074400 Housing-pump case Gehäuse Caja Carter 1

30 0089595 Diaphragm-pump Membran Diafragma Diaphragme 1

31 0074406 Mount-diaphragm Platte-Montage Placa-Montaje Plaque-montage 1

32 0051298 Plug 2", priming Deckel Tapón Bouchon 1

33 0074407 Port-suction Öffnung Lumbrera Port 1

34 0074408 Fitting-NPT Anschlußstück Pieza de conexión Raccord 1

34 0054150 Fitting-NPT/BSPT Anschlußstück Pieza de conexión Raccord 1

35 0025556 Screw 3/8x1-1/2 Schraube Tornillo Vis 4

35 0025649 Washer-lock 3/8 Federring Disco de resorte Rondelle de ressort 4

36 0051303 Screw #10-32x1/2 Schraube Tornillo Vis 4

37 0074411 Valve-weight retainer Ventil Válvula Soupape 2

38 0074410 Gasket-flapper valve Dichtung Empaque Joint 2

39 0074409 Weight-flapper valve Gewicht Peso Poids 2

40 0051297 Pin-grooved 1/8x3/8 Stift Pasador Goupille 2

41 0025650 Washer-lock 1/2 Federring Disco de resorte Rondelle de ressort 4

42 0025619 Nut 1/2 Mutter Tuerca Ecrou 4

43 0074412 Housing-water box Gehäuse Caja Carter 1

44 0051306 Handle-towing pole Handgriff Manija Poignée 1

45 0074401 Flange-discharge Flansch Brida Collerette 1

46 0025725 Nut-lock Sicherungsmutter Contratuercal Contre-écrou 1

47 * Axle-stub Achse Eje Essieu 2

Ref. Part No. Description Beschreibung Descripción Description Qty.

Page is loading ...

Wacker Neuson PDT2B User manual

Wacker Neuson PDT2B User manual

in other languages

Related papers

Other documents