Moxa ICS-G7852A Series User manual

ICS-G7852A Series
Moxa
Brand
Moxa
Model
ICS-G7852A Series
Category
Network switches
Type
User manual
Moxa Command Line Interface (FW_4.x)
Edition 5.2, October 2017
www.moxa.com/product
© 2017 Moxa Inc. All rights reserved.
Moxa Command Line Interface (FW_4.x)
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2017 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
+1-714-528-6777
Fax:
+1-714-528-6778
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
+86-21-5258-9955
Fax:
+86-21-5258-5505
Moxa Europe
Tel:
+49-89-3 70 03 99-0
Fax: +49-89-3 70 03 99-99
Moxa Asia
-Pacific
Tel:
+886-2-8919-1230
Fax: +886-2-8919-1231
Moxa India
Tel:
+91-80-4172-9088
Fax:
+91-80-4132-1045
Table of Contents
1. Command Modes ............................................................................................................................... 1-1
CLI (Command Line Interface) ............................................................................................................. 1-1
Configuring a Switch to CLI Mode ......................................................................................................... 1-1
Basic Operation .................................................................................................................................. 1-2
Useful Interactive “Help” Features ........................................................................................................ 1-3
Understanding All Commands ............................................................................................................... 1-3
2. Commands ........................................................................................................................................ 2-1
access-ip ........................................................................................................................................... 2-1
acl id ................................................................................................................................................. 2-1
acl id ip-base ..................................................................................................................................... 2-2
acl id mac-base .................................................................................................................................. 2-3
area .................................................................................................................................................. 2-3
area range ......................................................................................................................................... 2-4
area virtual-link .................................................................................................................................. 2-4
auth tacacs+ ...................................................................................................................................... 2-5
auth tacacs+ auth-type ....................................................................................................................... 2-5
auth tacacs+ server ............................................................................................................................ 2-6
auto-backup ....................................................................................................................................... 2-7
bind vlan ........................................................................................................................................... 2-7
clear counters .................................................................................................................................... 2-8
clear logging event-log ........................................................................................................................ 2-8
clock set ............................................................................................................................................ 2-8
clock summer-time ............................................................................................................................. 2-9
clock timezone ................................................................................................................................. 2-10
copy................................................................................................................................................ 2-10
dot1x auth ....................................................................................................................................... 2-11
dot1x auth ....................................................................................................................................... 2-12
dot1x local-userdb ............................................................................................................................ 2-12
dot1x reauth .................................................................................................................................... 2-13
dot1x reauth .................................................................................................................................... 2-13
dip-switch ........................................................................................................................................ 2-13
eip .................................................................................................................................................. 2-14
email-warning account ...................................................................................................................... 2-14
email-warning event ......................................................................................................................... 2-15
email-warning event ......................................................................................................................... 2-16
email-warning mail-address ............................................................................................................... 2-17
email-warning send test email ............................................................................................................ 2-18
email-warning server ........................................................................................................................ 2-18
exit ................................................................................................................................................. 2-19
flowcontrol ....................................................................................................................................... 2-19
gmrp ............................................................................................................................................... 2-20
gvrp ................................................................................................................................................ 2-20
hostname ........................................................................................................................................ 2-21
interface mgmt ................................................................................................................................. 2-21
interface vlan ................................................................................................................................... 2-22
ip address ........................................................................................................................................ 2-22
ip address ........................................................................................................................................ 2-23
ip auto-assign .................................................................................................................................. 2-23
ip default-gateway ............................................................................................................................ 2-24
ip dhcp retry .................................................................................................................................... 2-24
ip dhcp-relay server .......................................................................................................................... 2-25
ip dhcp-relay option82 ...................................................................................................................... 2-25
ip dhcp-relay option82 remote-id-type ................................................................................................ 2-26
ip http-server ................................................................................................................................... 2-26
ip http-server auto-logout .................................................................................................................. 2-27
ip igmp static-group .......................................................................................................................... 2-27
ip igmp-snooping .............................................................................................................................. 2-28
ip igmp-snooping enhanced ............................................................................................................... 2-28
ip igmp-snooping querier vlan ............................................................................................................ 2-29
ip igmp-snooping querier vlan vlan-id v3 ............................................................................................. 2-30
ip igmp-snooping query-interval ......................................................................................................... 2-30
ip igmp-snooping vlan ....................................................................................................................... 2-31
ip filter-ip ........................................................................................................................................ 2-31
ip name-server ................................................................................................................................. 2-32
ip ospf area ...................................................................................................................................... 2-32
ip ospf auth ..................................................................................................................................... 2-33
ip ospf cost ...................................................................................................................................... 2-33
ip ospf dead-interval ......................................................................................................................... 2-34
ip ospf hello-interval ......................................................................................................................... 2-34
ip ospf priority .................................................................................................................................. 2-35
ip pim-dm ........................................................................................................................................ 2-35
ip pim-sm ........................................................................................................................................ 2-36
ip pim-sm dr-priority ......................................................................................................................... 2-36
ip pim-sm hello-interval ..................................................................................................................... 2-37
ip pim-sm join-prune-interval ............................................................................................................. 2-37
ip proxy-arp ..................................................................................................................................... 2-38
ip route ........................................................................................................................................... 2-38
ipv6 address .................................................................................................................................... 2-38
line-swap-fast-recovery ..................................................................................................................... 2-39
lldp enable ....................................................................................................................................... 2-40
lldp timer ......................................................................................................................................... 2-40
logging ............................................................................................................................................ 2-41
login mode ....................................................................................................................................... 2-41
mac-address-table aging-time ............................................................................................................ 2-42
mcast-filter ...................................................................................................................................... 2-42
media cable-mode ............................................................................................................................ 2-43
modbus ........................................................................................................................................... 2-43
monitor ........................................................................................................................................... 2-44
Management-Interface ...................................................................................................................... 2-44
name .............................................................................................................................................. 2-45
network ........................................................................................................................................... 2-45
ntp refresh-time ............................................................................................................................... 2-46
ntp remote-server ............................................................................................................................ 2-47
ntp server ........................................................................................................................................ 2-47
permit ............................................................................................................................................. 2-48
ping ................................................................................................................................................ 2-48
port-security .................................................................................................................................... 2-48
profinetio ......................................................................................................................................... 2-49
ptp announce-receipt-timeout ............................................................................................................ 2-49
ptp arb-time .................................................................................................................................... 2-50
ptp clockclass ................................................................................................................................... 2-50
ptp domain-number .......................................................................................................................... 2-51
ptp enable ....................................................................................................................................... 2-51
ptp leap59 ....................................................................................................................................... 2-52
ptp leap61 ....................................................................................................................................... 2-52
ptp log-sync-interval ......................................................................................................................... 2-53
ptp log-announce-interval .................................................................................................................. 2-53
ptp log-min-delay-req-interval ........................................................................................................... 2-54
ptp log-min-pdelay-req-interval .......................................................................................................... 2-54
ptp mode ......................................................................................................................................... 2-55
ptp preferred-master......................................................................................................................... 2-55
ptp priority1 ..................................................................................................................................... 2-56
ptp priority2 ..................................................................................................................................... 2-56
ptp timescale ................................................................................................................................... 2-57
ptp transport .................................................................................................................................... 2-57
ptp utc-offset ................................................................................................................................... 2-58
ptp utc-offset-valid ........................................................................................................................... 2-58
qos highest-priority ........................................................................................................................... 2-59
qos default-cos ................................................................................................................................. 2-59
qos inspect ...................................................................................................................................... 2-60
qos mapping .................................................................................................................................... 2-60
qos mode ........................................................................................................................................ 2-61
quit ................................................................................................................................................. 2-61
rate-limit ......................................................................................................................................... 2-62
redistribute ...................................................................................................................................... 2-63
redundancy ...................................................................................................................................... 2-63
redundancy mode ............................................................................................................................. 2-64
relay-warning config relay ................................................................................................................. 2-64
relay-warning event .......................................................................................................................... 2-65
relay-warning event .......................................................................................................................... 2-65
relay-warning override ...................................................................................................................... 2-66
reload ............................................................................................................................................. 2-67
router ospf ....................................................................................................................................... 2-67
router rip ......................................................................................................................................... 2-68
router vrrp ....................................................................................................................................... 2-68
router vrrp adver-interval .................................................................................................................. 2-69
save config ...................................................................................................................................... 2-69
show acl .......................................................................................................................................... 2-70
show auth tacacs+ ............................................................................................................................ 2-70
show clock ....................................................................................................................................... 2-71
show dot1x ...................................................................................................................................... 2-72
show dot1x local-userdb .................................................................................................................... 2-72
show eip .......................................................................................................................................... 2-73
show PROFINETIO ............................................................................................................................ 2-73
show email-warning config ................................................................................................................. 2-73
show gmrp....................................................................................................................................... 2-75
show gvrp ........................................................................................................................................ 2-75
show interfaces acl ........................................................................................................................... 2-75
show interfaces counters ................................................................................................................... 2-76
show interfaces ethernet ................................................................................................................... 2-77
show interfaces filter-ip ..................................................................................................................... 2-78
show interfaces mgmt ....................................................................................................................... 2-79
show interfaces mgmt access-ip ......................................................................................................... 2-79
show interfaces rate-limit .................................................................................................................. 2-80
show interfaces trunk ........................................................................................................................ 2-80
show interfaces vlan ......................................................................................................................... 2-81
show interfaces mgmt trusted-access .................................................................................................. 2-82
show ip auto-assign .......................................................................................................................... 2-82
show ip dhcp-relay config .................................................................................................................. 2-83
show ip http-server status ................................................................................................................. 2-84
show ip igmp ................................................................................................................................... 2-84
show ip ospf ..................................................................................................................................... 2-85
show ip ospf database ....................................................................................................................... 2-86
show ip ospf interface ....................................................................................................................... 2-86
show ip ospf neighbor ....................................................................................................................... 2-87
show ip pim-dm................................................................................................................................ 2-87
show ip pim-dm neighbor .................................................................................................................. 2-88
show ip pim-sm ................................................................................................................................ 2-88
show ip pim-sm bsr .......................................................................................................................... 2-89
show ip pim-sm neighbor ................................................................................................................... 2-89
show ip pim-sm routing ..................................................................................................................... 2-90
show ip pim-sm rp ............................................................................................................................ 2-91
show ip rip ....................................................................................................................................... 2-91
show ip route ................................................................................................................................... 2-92
show ip vrrp ..................................................................................................................................... 2-92
show lldp ......................................................................................................................................... 2-93
show logging .................................................................................................................................... 2-94
show mac-address-table .................................................................................................................... 2-95
show mac-address-table aging-time .................................................................................................... 2-96
show mcast-filter .............................................................................................................................. 2-96
show modbus ................................................................................................................................... 2-97
show port monitor ............................................................................................................................ 2-97
show port-security ............................................................................................................................ 2-97
show qos ......................................................................................................................................... 2-98
show redundancy mst configure ......................................................................................................... 2-99
show redundancy mst instance ......................................................................................................... 2-100
show redundancy spanning-tree ....................................................................................................... 2-101
show redundancy turbo-chain .......................................................................................................... 2-101
show redundancy turbo-ring-v1 ........................................................................................................ 2-102
show redundancy turbo-ring-v2 ........................................................................................................ 2-103
show relay-warning ......................................................................................................................... 2-104
show running-config ........................................................................................................................ 2-105
show startup-config ........................................................................................................................ 2-106
show snmp .................................................................................................................................... 2-107
show storm-control ......................................................................................................................... 2-107
show system .................................................................................................................................. 2-108
show users .................................................................................................................................... 2-108
show vlan ...................................................................................................................................... 2-109
show vlan config ............................................................................................................................. 2-109
shutdown....................................................................................................................................... 2-110
snmp-server community .................................................................................................................. 2-111
snmp-server contact ....................................................................................................................... 2-111
snmp-server description .................................................................................................................. 2-112
snmp-server host ........................................................................................................................... 2-112
snmp-server location....................................................................................................................... 2-113
snmp-server trap-mode ................................................................................................................... 2-113
snmp-server user ........................................................................................................................... 2-114
snmp-server version ....................................................................................................................... 2-114
spanning-tree forward-delay ............................................................................................................ 2-115
spanning-tree hello-time ................................................................................................................. 2-115
spanning-tree max-age ................................................................................................................... 2-116
spanning-tree mst cist cost .............................................................................................................. 2-116
spanning-tree mst cist port-priority ................................................................................................... 2-117
spanning-tree mst cist priority .......................................................................................................... 2-117
spanning-tree mst edge-port ............................................................................................................ 2-118
spanning-tree mst enable ................................................................................................................ 2-118
spanning-tree mst forward-time ....................................................................................................... 2-119
spanning-tree mst hello-time ........................................................................................................... 2-119
spanning-tree mst instance .............................................................................................................. 2-120
spanning-tree mst instance cost ....................................................................................................... 2-120
spanning-tree mst instance port-priority ............................................................................................ 2-121
spanning-tree mst instance priority ................................................................................................... 2-121
spanning-tree mst max-age ............................................................................................................. 2-122
spanning-tree mst max-hops ........................................................................................................... 2-122
spanning-tree mst name .................................................................................................................. 2-123
spanning-tree mst revision .............................................................................................................. 2-123
spanning-tree priority...................................................................................................................... 2-124
spanning-tree ................................................................................................................................. 2-124
spanning-tree cost .......................................................................................................................... 2-125
spanning-tree edge-port .................................................................................................................. 2-125
spanning-tree priority...................................................................................................................... 2-126
speed-duplex ................................................................................................................................. 2-126
storm-control ................................................................................................................................. 2-127
switchport access vlan ..................................................................................................................... 2-127
switchport hybrid fixed vlan add ....................................................................................................... 2-128
switchport hybrid forbidden vlan add ................................................................................................. 2-128
switchport hybrid forbidden vlan remove ........................................................................................... 2-129
switchport hybrid native vlan ........................................................................................................... 2-129
switchport pvlan ............................................................................................................................. 2-130
switchport trunk fixed vlan add ........................................................................................................ 2-130
switchport trunk fixed vlan remove ................................................................................................... 2-131
switchport trunk forbidden vlan add .................................................................................................. 2-131
switchport trunk forbidden vlan remove ............................................................................................. 2-132
switchport trunk native vlan ............................................................................................................. 2-132
trunk-group ................................................................................................................................... 2-133
trunk-mode .................................................................................................................................... 2-133
turbo-chain .................................................................................................................................... 2-134
turbo-ring-v1 ................................................................................................................................. 2-134
turbo-ring-v1 coupling ..................................................................................................................... 2-135
turbo-ring-v1 master ...................................................................................................................... 2-135
turbo-ring-v2 ................................................................................................................................. 2-136
turbo-ring-v2 coupling backup .......................................................................................................... 2-137
turbo-ring-v2 coupling dual-homing .................................................................................................. 2-137
turbo-ring-v2 coupling primary ......................................................................................................... 2-138
turbo-ring-v2 master ...................................................................................................................... 2-139
trusted-access ................................................................................................................................ 2-139
username ...................................................................................................................................... 2-140
version .......................................................................................................................................... 2-140
vlan create..................................................................................................................................... 2-141
vlan mode ..................................................................................................................................... 2-142
vrrp .............................................................................................................................................. 2-142
vrrp preempt .................................................................................................................................. 2-143
vrrp priority ................................................................................................................................... 2-143
warning-notification system-event .................................................................................................... 2-144
warning-notification port-event ........................................................................................................ 2-145
1
1. Command Modes
CLI (Command Line Interface)
The CLI (command line interface) for Moxa switches can be accessed through either the serial console or Telnet
console. For either type of connection, access to the command line interface is generally referred to as an EXEC
session.
Configuring a Switch to CLI Mode
The default configuration mode for both the serial console and Telnet console is MENU mode. To change the
Moxa switch to CLI configuration mode, Login Mode from Basic Settings and then press y to activate the
change. You will then be able to view the CLI display in the console. (Note that the default login user name is
admin, without a password.)
1. Select Basic Settings.
2. Select Login mode.
Moxa Command Line Interface (FW_4.x) Command Modes
1-2
3. Press y to activate.
4. Now log in to access CLI display mode.
After changing to CLI mode, CLI mode will be the default setting for the next reboot.
Basic Operation
The CLI is organized in different configuration levels. When you first enter CLI mode, type ? to view a quick help
panel that shows the basic commands of the first configuration level. Type any of the commands shown on the
screen to access the next configuration level. The quick help panel, accessed from any level by typing ?, is a
useful tool for understanding the commands in any level.
To enter the next level, type the commands shown in the console.
To leave access the next higher level, type exit.
To jump directly back to the first level, type Ctrl + z.
Moxa Command Line Interface (FW_4.x) Command Modes
1-3
Useful Interactive “Help” Features
The CLI includes several types of interactive commands. The Help commands are listed in the following table:
Command Purpose
? Provides a brief description of the Help feature in any command level.
Partial command? Provides a list of commands that begin with the character string (no space
between the command and the question mark).
Partial command<Tab> Completes a partial command name (no space between the command and
<Tab>).
Command ? Lists the keywords, arguments, or both associated with the command (type a
space between the command and the question mark).
Command keyword ? Lists the arguments that are associated with the keyword (type a space
between
the keyword and the question mark).
Understanding All Commands
To understand all the details of the commands supported in the CLI of Moxa switches, refer to the following
table.
Mode Access Method Prompt Exit Method About This Mode
User EXEC
Begin a session with
your switch and
login with user.
Switch> Enter exit or quit. Use this mode to display
system information.
Privileged EXEC
Begin a session with
your switch and
login with admin.
Switch# Enter exit or quit. Use this mode to verify
commands that you have
entered.
Global
configuration
While in privileged
EXEC mode, enter
the configure
command.
Switch(config)#
To exit to privileged EXEC
mode, enter exit or press
Ctrl-Z.
Use this mode to
configure parameters that
apply to the entire switch.
Redundancy
configuration
From global
configuration mode,
enter the
redundancy
command.
Switch(config-rdnt)#
To exit to privileged EXEC
mode, press Ctrl-Z.
To exit to global
configuration mode, enter
the exit command.
Use this mode to
configure Turbo Ring
V1/V2, Turbo Chain, and
Spanning Tree
parameters.
Interface
configuration
From global
configuration mode,
specify an interface
by entering the
interface command
followed by an
interface
identification.
Switch(config-if)#
To exit to privileged EXEC
mode, press Ctrl-Z.
To exit to global
configuration mode, enter
the exit command.
Router
configuration
From global
configuration mode,
specify a protocol by
entering the router
command.
Switch(config-rip)#
Switch(config-ospf)#
To exit to privileged EXEC
mode, press Ctrl-Z.
To exit to global
configuration mode, enter
the exit command.
2
2. Commands
access-ip
Use access-ip in the VLAN configuration command as to restrict access to the switch to specified IP addresses.
Use the no form of this command to disable this feature or to remove the IP addresses from access list.
Commands
access-ip [ip-address netmask]
no access-ip [ip-address netmask]
Syntax
Description
access-ip Enable the accessible IP list
ip-address IP address
netmask IP netmask
Defaults The feature is disabled by default.
Command
Modes
VLAN configuration as management VLAN
Usage
Guidelines
This feature will take effect when the access-ip command is executed.
Examples
PT-7828(config)# interface mgmt
PT-7828(config-vlan)# access-ip 10.10.10.10 255.255.255.0
<IPV4ADDR:ipaddr> - IP address
<IPV4ADDR:netmask> - IP netmask
PT-7828(config-vlan)# access-ip
Error
messages
IP or netmask invalid
Access IP list full
Related
commands
show interface mgmt access-ip
acl id
The command is supported only in Layer 3 switches
Use acl id interface configuration commands on the switch to attach ACL to the port. Use the no form of this
command to return to the default setting.
Commands
acl id { in | out}
no acl id
Syntax
Description
acl Configure access control list
id The access list ID
in Inbound traffic
out Outbound traffic
Defaults N/A
Command
Modes
Interface configuration
Moxa Command Line Interface (FW_4.x) Commands
2-2
Usage
Guidelines
N/A
Examples
PT-7828(config-if)# acl 10 in
PT-7828(config-if)# no acl 10
Error
messages
Invalid ID!
Related
commands
acl id ip-base
The command is supported only in Layer 3 switches
Use the acl id ip-base global configuration commands on the switch to create an IP-base ACL and add rules.
Use the no form of this command to remove the rule.
Commands
acl id ip-base { permit | deny } srcip [ dstip] [ protocol ] [ port ]
acl id ip-base name name_str
no acl id
no acl id rule ruleindex
Syntax
Description
acl Configure access control list
Id Set ACL ID
ip-base IP-base ACL
permit Forward packets
deny Drop packets
srcip Set source IP address and subnet mask. Ex: 192.168.1.1/255.255.255.0 or
192.168.127.1
dstip
Set destination IP address and subnet mask. Ex: 192.168.1.1/255.255.255.0
or 192.168.127.1
protocol Set protocol number, Ex: ICMP, TCP, UDP, etc.
port Set TCP/UDP port number
name_str ACL name
Defaults N/A
Command
Modes
Global configuration
Usage
Guidelines
The ACL ID is 1 ~ 16.
Examples
PT-7828(config)# acl 8 ip-base permit 172.3.1.1/255.255.255.0
201.16.9.7/255.255.0.0 6 23
Error
messages
Invalid ID!
This ID is used by MAC-base ACL!
Invalid IP address format!
Invalid subnet mask format!
Related
commands
Moxa Command Line Interface (FW_4.x) Commands
2-3
acl id mac-base
The command
is supported only in Layer 3 switches
Use the acl id mac-base global configuration commands on the switch to create an MAC-base ACL and add
rules. Use the no form of this command to remove the rule.
Commands
acl id mac-base { permit | deny } srcmac [ dstmac] [ ethertype ] [ vid ]
acl id mac-base name name_str
no acl id
no acl id rule ruleindex
Syntax
Description
Acl Configure access control list
Id Set ACL ID
mac-base MAC-base ACL
permit Forward packets
Deny Drop packets
srcmac Set source MAC address and MAC mask. Ex:
00:90:E8:1D:24:23/FF:FF:FF:FF:00:00 or 00:90:E8:1D:24:23
dstmac Set destination IP address and subnet mask. Ex:
192.168.1.1/255.255.255.0 or 192.168.127.1
ethertype Set ether type
Vid Set VLAN ID
name_str ACL name
Defaults N/A
Command
Modes
Global configuration
Usage
Guidelines
The ACL ID is 1 ~ 100.
Examples
PT-7828(config)# acl 10 mac-base deny 00:11:22:33:44:55/ff:ff:ff:00:00:00
aa:bb:cc:dd:ee:ff/ff:ff:00:00:00:00 2048 10
Error messages Invalid ID!
This ID is used by IP-base ACL!
Invalid MAC address format!
Invalid MAC mask format!
Related
commands
area
Use the area command in Router configuration mode as OSPF to add an OSPF area and configure its type. Use
the no form of this command to remove the area.
Commands
area area-id [ { stub | nssa } metric value ]
no area area-id
Syntax
Description
area Configure OSPF Area
area-id OSPF Area id, format is ip address
stub Configure OSPF area type to stub
nssa Configure OSPF area type to NSSA
metric Configure OSPF area metric
value Metric value ( 1 to 65535)
Defaults N/A
Moxa Command Line Interface (FW_4.x) Commands
2-4
Command
Modes
Router configuration mode as OSPF
Usage
Guidelines
Metric value: 1 to 65535
Examples
PT-7828(config-ospf)# area 2.2.2.2
PT-7828(config-ospf)# area 2.2.2.2 stub metric 4
PT-7828(config-ospf)# area 2.2.2.2 nssa metric 4
Error messages Configuration Error!!
Metric value error (1 to 65535)!!
Related
commands
show ip ospf
area range
To consolidate and summarize routes at an area boundary, use the area range command in router
configuration mode. To disable this function, use the no form of this command.
Commands
area area-id range ip-address netmask
no area area-id range ip-address netmask
Commands area Configure OSPF Area
area-id OSPF Area id, format is ip address
range
Specify an address range for route aggregation
ip-address E.g., 11.22.33.44
netmask E.g., 255.255.255.0
Defaults N/A
Command
Modes
Router configuration mode as OSPF
Usage
Guidelines
N/A
Examples
PT-7828(config-ospf)# area 1.1.1.1 range 192.0.0.0 255.0.0.0
Error messages Configuration Error!!
IP Prefix format Error!!
Netmask format Error!!
IP format Error!!
Related
commands
show ip ospf
area virtual-link
Use the area virtual-link command in Router configuration mode as OSPF to add an OSPF virtual link. Use the
no form of this command to remove the specified OSPF virtual link.
Commands
area area-id virtual-link router-id
no area area-id virtual-link router-id
Syntax
Description
area Configure OSPF Area
area-id OSPF Area id
virtual-link Establish a virtual link
router-id
Neighbor Router ID
Defaults N/A
Moxa Command Line Interface (FW_4.x) Commands
2-5
Command
Modes
Router configuration mode as OSPF
Usage
Guidelines
N/A
Examples
PT-7828(config-ospf)# area 1.1.1.1 virtual-link 0.0.0.0
Error messages
Configuration Error!!
Related
commands
show ip ospf
auth tacacs+
Use the auth tacacs+ global configuration command on the switch to enable TACACS+ authentication. Use
the no form of this command to return to the default setting.
Commands
auth tacacs+
no auth tacacs+
Syntax
Description
auth Configure authentication mechanism
tacacs+ TACACS+ authentication
Defaults The default setting is disabled.
Command
Modes
Global configuration
Usage
Guidelines
N/A
Examples
PT-7828(config)# auth tacacs+
Error
messages
N/A
Related
commands
show auth tacacs+
auth tacacs+ auth-type
Use the auth tacacs+ auth-type global configuration command on the switch to specify the type of TACACS+
authentication. Use the no form of this command to return to the default setting.
Commands
auth tacacs+ auth-type { ascii | pap | chap | arap | mschap }
no auth tacacs+ auth-type
Syntax
Description
auth Configure authentication mechanism
tacacs+ TACACS+ authentication
auth-type Specify the authentication type
ascii Normal ASCII code authentication
pap Password Authentication Protocol
chap Challenge-handshake authentication protocol
arap AppleTalk Remote Access Protocol
mschap Microsoft Challenge-handshake authentication protocol
Defaults Default type is ASCII code authentication
Command
Modes
Global configuration
Usage
Guidelines
To enable the TACACS+ authentication, the command “auth tacacs+” must be executed first.
Moxa Command Line Interface (FW_4.x) Commands
2-6
Examples
PT-7828(config)# auth tacacs+ auth-type
ascii - Normal ASCII code authentication
pap - Password Authentication Protocol
chap - Challenge-handshake authentication protocol
arap - AppleTalk Remote Access Protocol
mschap - Microsoft Challenge-handshake authentication protocol
Error
messages
N/A
Related
commands
auth tacacs+
show auth tacacs+
auth tacacs+ server
Use the auth tacacs+ server global configuration command on the switch to set the TACACS+ authentication
server address and the shared key information. Use the no form of this command to remove the settings.
Commands
auth tacacs+ server server-address shared-key key [timeout seconds]
no auth tacacs+ server
Syntax
Description
auth Configure authentication mechanism
tacacs+ TACACS+ authentication
server TACACS+ authentication server
server-address Authentication server address
shared-key Configure the shared key
key Key string, max 15 characters
timeout Configure server timeout
seconds 1 to 255 sec.
Defaults Default timeout is 30 seconds
Default tacacs+ server port is 49
Command
Modes
Global configuration
Usage
Guidelines
To enable the TACACS+ authentication, the command “auth tacacs+” must be executed first.
Examples
PT-7828(config)# auth tacacs+ server
<STRING:auth_server> - Authentication server address
PT-7828(config)# auth tacacs+ server tacacs.server.moxa.com
shared-key - Configure the shared key
PT-7828(config)# auth tacacs+ server tacacs.server.moxa.com shared-key
<STRING:key> - Key string, max 15 characters
PT-7828(config)# auth tacacs+ server tacacs.server.moxa.com shared-key 1234
<LF>
timeout - Configure server timeout
PT-7828(config)# auth tacacs+ server tacacs.server.moxa.com shared-
key 1234
timeout
<UINT:seconds> - 1 to 255 sec.
PT-7828(config)# auth tacacs+ server tacacs.server.moxa.com shared-
key 1234
timeout 200
Error
messages
Timeout value must be in the range from 1 to 255 seconds
Invalid IP protocol port
Related
commands
auth tacacs+
show auth tacacs+
Moxa Command Line Interface (FW_4.x) Commands
2-7
auto-backup
Use auto-backup to enable Auto load system configurations when the system boots up. To disable it, use the
no form of this command.
Commands
auto-backup
no auto-backup
Syntax
Description
auto-backup Use auto backup configurator to restore configuration
Defaults Auto-backup configuration is enabled by default.
Command
Modes
Global configuration
Usage
Guidelines
N/A
Examples
PT-7828# configure terminal
PT-7828(config)# auto-backup
PT-7828(config)# no au
auto-backup - Deactive auto-backup configurator
PT-7828(config)# no auto-backup
Error
messages
N/A
Related
commands
N/A
bind vlan
Use the bind vlan configuration command on the switch to bind the management address with a specified
VLAN ID. Use the no form of this command to return to the default.
Commands
bind vlan VLAN-ID
Syntax
Description
bind Bind VLAN as management VLAN
vlan VLAN parameters
VLAN-ID 1 to 4094
Defaults Default management VLAN ID is 1
Command
Modes
VLAN configuration mode as management VLAN
Usage
Guidelines
N/A
Examples
PT-7828(config)# interface mgmt
PT-7828(config-vlan)# bind vlan
<UINT:vlanid> - 1 to 4094
Error
messages
L3 interface cannot be assigned as management interface
VLAN id is out of range!
Related
commands
show interfaces mgmt
Moxa Command Line Interface (FW_4.x) Commands
2-8
clear counters
Use the clear counters user EXEC command on the switch to clear the switch’s statistics counters.
Commands
clear counters
Syntax
Description
clear Clear information
counters Clear statistic counters
Defaults N/A
Command
Modes
Privileged
Usage
Guidelines
N/A
Examples
PT-7828# clear
counters - Clear statistic counters
Error
messages
N/A
Related
commands
show interfaces counters
clear logging event-log
Use the clear logging event-log user EXEC command on the switch to clear the system log of the switch.
Commands
clear logging event-log
Syntax
Description
clear Clear information
logging System event logs
event-log
System event logs
Defaults N/A
Command
Modes
Privileged
Usage
Guidelines
N/A
Examples
PT-7828# clear
logging - System event logs
PT-7828# clear logging
event-log - System event logs
Error
messages
N/A
Related
commands
show logging
clock set
Use the clock set global configuration command on the switch to set the current switch time.
Commands
clock set hh:mm:ss month day year
Syntax
Description
clock Configure time-of-day clock
set Adjust the clock
hh:mm:ss hh:mm:ss
Moxa Command Line Interface (FW_4.x) Commands
2-9
month 1 to 12
day 1 to 31
year 2000 to 2037
Defaults N/A
Command
Modes
Global configuration
Usage
Guidelines
N/A
Examples
PT-7828(config)# clock set 11:11:11 1 1 2010
Error
messages
Illegal parameters!
Related
commands
show clock
clock summer-time
Use the clock summer-time global configuration command on the switch to enable the daylight saving time
offset and set the apply duration. Use the no form of this command to disable it.
Commands
clock summer-time start-date month week day hour
clock summer-time end-date month week day hour
clock summer-time offset offset-hour
Syntax
Description
clock Configure time-of-day clock
summer-time Configure Summer time parameter
start-date The date when summer time offset start
end-date The date when summer time offset end
month From ‘Jan’, ‘January’ or ‘1’ to ‘Dec’, ‘December’, or ‘12’
week From ‘1st’ or ‘1’ to ‘Last’ or ‘6’
day From ‘Sun’, ‘Sunday’ or ‘1’ to ‘Sat’, ‘Saturday’ or ‘7’
hour 0 to 23
offset Summer time offset
offset-hour 1 to 12
Defaults N/A
Command
Modes
Global configuration
Usage
Guidelines
When configuring the summer time offset, the start-date and end-date must be configured
correctly first.
Examples
PT-7828(config)# clock timezon gmt -4
Error
messages
Invalid parameter
Month must be configured as ‘Jan’, ‘January’ or a numerical ‘1’.
Week must be configured as ‘1st’, ‘2nd’, ‘3rd’, ‘4th’, ‘5th’ or ‘Last’
Day must be configured as ‘Sun’, ‘Sunday’ or a numerical ‘1’.
Hour must be in the range from 0 to 23.
Please input the correct start/end date of the summer time first!
Hour offset is out of range.
Related
commands
show clock
Moxa Command Line Interface (FW_4.x) Commands
2-10
clock timezone
Use the clock timezone global configuration command on the switch to set the current time zone.
Commands
clock timezone gmt offset-hour
Syntax
Description
clock Configure time-of-day clock
timezone Time zone hour shifting
gmt Greenwich Mean Time
offset-hour -12 to 12
Half an hour Only type 30
Defaults
N/A
Command
Modes
Global configuration
Usage
Guidelines
N/A
Examples
EDS-G516E(config)# clock timezone gmt 5 30
Error
messages
This timezone doesn’t support half an hour
Related
commands
show clock
copy
Use the copy privileged command on the switch to copy an image or configuration file from a remote server to
the Flash memory or copy the running configuration, startup configuration, or event log to a remote server via
TFTP.
Commands
copy tftp device-firmware
copy tftp running-config
copy {running-config|event-log|startup-config} tftp [tftp-address]
Syntax
Description
copy Copy from one file to another
tftp
Remote server through TFTP
device-firmware System firmware
running-config Current running configuration of system
startup-config System startup configuration
event-log Event log file
tftp-address TFTP address. E.g., tftp://192.168.127.1/abc.txt
Defaults N/A
Command
Modes
Privileged EXEC
Usage
Guidelines
N/A
Examples
PT-7828# copy tftp
device-firmware - System firmware
running-config - Current running configuration of system
PT-7828# copy tftp running-config
Address or name of remote host [192.168.127.1]? 192.168.127.95
Source file name ? cli.ini
Save import config to flash ? [Y/n]
Saving configuration ...Success
Moxa Command Line Interface (FW_4.x) Commands
2-11
Error
messages
Input error
Invalid TFTP Server IP/Name !!!
TFTP Configuration File Download Failed
Invalid Config Files Path and Name !!!
Invalid Firmware Files Path and Name !!!
TFTP Firmware Download Failed !!!
TFTP Configuration File Upload Failed !!!
TFTP Log File Upload Failed !!!
Related
commands
N/A
dot1x auth
Use the dot1x auth global configuration command to set dot1x authentication type and relative
configurations.
Commands
dot1x auth local
dot1x auth radius server server port port shared-key string
dot1x auth radius-local server server port port shared-key string
Syntax
Description
dot1x 802.1x setting
auth 802.1x auth type
local 802.1x authentication uses local database
radius 802.1x authentication uses radius server
radius-local 802.1x authentication uses both local and radius server
server 802.1x radius server name/ip
server 802.1x radius server name/ip string
port
802.1x radius server port
port 802.1x radius server port (default 1812)
shared-key 802.1x Shared Key
string Shared Key string
Defaults 802.1x local authentication
Command
Modes
Global configuration
Usage
Guidelines
N/A
Examples
PT-7828(config)# dot1x auth local
PT-7828(config)# dot1x auth radius server moxanet port 1812 shared-key moxa
PT-7828(config)# dot1x auth radius-local server moxanet port 1812 shared-key moxa
Error messages Local Database is Full !!!
Invalid User Name !!!
Invalid User Password !!!
Invalid User Description !!!
Related
commands
show dot1x
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155

Moxa ICS-G7852A Series User manual

ICS-G7852A Series
Moxa
Brand
Moxa
Model
ICS-G7852A Series
Category
Network switches
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents