Please read this manual thoroughly before use, and keep it handy for future reference
Water Proof Infrared camera
1. Color: 1/3"SONY CCD Camera with
520/420(High/Standard) TV lines of resolution.
2. Easy to install and adjust.
3. Minimum illumination:
0.04 lux(F1.6,10IRE);
0.6 lux(F1.6,50IRE)
0 lux(When IR LEDs are on)
4. All-in-one function excellent for both
indoor & outdoor applications.
5. Water proof of IP66 makes it ideal for
outdoor surveillant applications.
1. Do not touch the lens surface of the sensor.
Use soft cloth moistened with alcohol to
clean the surface if it is touched accidentally.
2. Ensure the supply voltage is correct as
speciced for the particular variant of
camera before operation.
3. Do not expose the camera to rain, moisture
or to the temperature exceeds the specied
limit, without a suitable housing.
4. Avoid aiming the camera at very bright
objects such as the sun or electric lights
for an extended period.
5. Do not attempt to service this unit yourself
unless your are authorized to do so.
Opening or removing cover may expose
yourself to the dangerous voltage or other
hazards. Refer all servicing to qualied
personnel only.
1.
2.
3.
Connects to the VIDEO IN connector of
the Monitor Video Connector & Power
Connector.
4.
Connects to the external power
source(DC12V).
5. !"
Use this mounting hole to connect to
the mount bracket while mounting
onto the ceiling.
6. # !"
Use this mounting hole to connect to
the mount bracket while mounting
onto the wall.
7. $%
Connects to the Mount.
8. &%
Connects the BNC connector and the
power connector to the respective
connectors.
&
$"
'#(
1
3
6
8
2
5
7
4
Part #: i3R351
---
©2009 i³International. The i³ logo is property of i³International Inc. All rights reserved. Specifications, configurations, components and
options listed are subject to change without notice. This data sheet may not be reproduced without permission.
www.i3international.com
1.866.840.0004
U.S.A. 440 Lawrence Bell Drive,
Suite 16, Williamsville.
NY, 14221
Canada 780 Birchmount Road
Unit 16, Scarborough
ON, M1K 5H4
##
1. Place the $% against a
at surface in the desired location you
wish to mount the IR camera onto.
Mark the location using the three
mounting holes.
2. Drill the 3 holes(Ø=0.208" (5.3mm),
depth=1" (25mm). according to the
mark made from the previously.
3. Use the hammer to put an anchor hold
provided to each hole just drilled.
(Fig-1)
4. Fix the $% onto the wall/
ceiling using the 3 screws.(Fig-1)
5. Combine the $% with the
by fastening the
screws on the $%to the
!")"
t oount!o" when mounting
on the ceiling/wall.(Fig-2)
Water Proof Infrared Camera
INSTRUCTION MANUAL
(*$
1. Loosen the &%.
2. Adjust the swivel and the tilt angle
of the IR camera to your desired
direction, then fasten the &
% to maintain the angle adjusted.
Fig-1
Fig-2
SPECIFICATION
Image System
Image pickup sensor 1/3”-SONY CCD
Effective pixels(HxV) NTSC HI:768 x 494
NTSC STD :510 x 492
PAL HI:752 x 582
PAL STD:510 x 582
Electrical
Scanning system NTSC HI, NTSC STD:
2:1 interlace, V:59.94Hz,
H:15.734KHz.
PAL HI, PAL STD:
2:1 interlace,V:50Hz,H:15.625KHz
Sync system Internal
Lens f=4.3mm, F1.6
Horizontal resolution High-res:520TVL
Standard-res:420TVL
Minimum illumination 0.04 lux(F1.6,10IRE)/0.6
lux(F1.6,50IRE)
0 lux(When IR LEDs are on)
S/N ratio More than 50dB
AES(Auto electronic shutter) NTSC: 1/60 ~1/100000sec
PAL : 1/50 ~1/100000sec
Gain control Auto
BLC(Backlight compensation) On
White balance ATW (Auto trace white balance)
Video output 1Vpp composite output 75ohm
Power Supply
Power requirement DC12V ± 10%
Power consumption 4.5W(Max)
Enviroment
Operating temperature
Operating humidity 30% ~ 90%
Storage temperature
Mechanical
Dimensions 57 (Ø) x68 (H)mm
Weight 450g approx (with bracket)
/
