Panasonic TYWK42PV1U Operating instructions

Fäste för väggupphängning (lodrätt)

för bred plasma-monitor

Monteringsanvisningar

Läs dessa anvisningar noggrant innan du monterar samman

dessa tillbehör. Behåll häftet för framtida referens.

Vægbeslag (lodret) til

widescreen-plasmaskærm

Monteringsvejledning

Læs grundigt igennem denne vejledning inden du samler

disse tilbehør. Behold vejledningen for brug i fremtiden.

Abrazadera de suspensión de pared (vertical)

para pantalla Panarámica de Plasma

Instrucciones de instalación

Antes del instalar estis accesorios, lea cuidadosamente

estas instrucciones.

Guarde estas instrucciones para futuras referencias.

Applique de suspension au mur (verticale)

pour l’Ecran plasma 16/9ème

Manuel d’installation

Avant d’essayer d’assembler ces accessories, vauillez lire

ces instructions complètement.

Veuillez garder ce manuel pour une référence future.

Staffa per sospensione a parete (verticale)

per lo scheromo al Plasma-16:9

Instruzioni per I’installazione

Prima di iniziare a montare questi accessori, siete pregati di

leggere interamente le presenti istruzioni.

Siete inoltre pregati di conservare questo libro per future

consultazioni.

Muurbevestigingssteun (Vertikaal) voor

Breedbeeld Plasmadisplay Monitor

Installatiehandleiding

Lees deze handleiding zorgvuldig door alvorens u probeert

deze accessoires te monteren. Bewaar de handleiding voor

het geval dat u later iets wilt opzoeken.

Wandhängehalterung (Vertikal)

für Plasmadisplay

Installationsanleitung

Vor der Installation lesen Site bitte diese Anleitung sorgfaltig

durch. Diese Anleitung zum spateren Nachschlagen

aufbewahren.

Wall-hanging bracket (Vertical)

for Wide Plasma Display

Installation Instructions

Before attempting to assemble these accessories, please

read these instructions completely.

Please retain this book for future reference.

TY-WK42PV1

MODEL No.

English

Deutsch

Nederlands

Italiano

Français

Español

Svenska

Dansk

TQZH239-2

2

English

Thank you very much for purchasing the Panasonic Wide Plasma Display

Wall-

hanging bracket

.

Installation work should only be carried out by a qualified technician.

•

If the bracket is installed incorrectly, the display may fall down and personal injury may result.

Precautions with regard to setting up

WARNING

Installation work should only be carried out by a qualified technician.

• If the bracket is installed incorrectly, the display may fall down and personal injury may result.

Make sure that all safety factors regarding strength of installation are observed.

• If the installation strength is insufficient, the display may fall down and personal injury may

result.

Do not install in places which are unable to bear loads.

• If the strength of the installation surface is insufficient, the display may fall down and personal

injury may result.

CAUTION

Do not install in places which are subject to humidity, dust, oil fumes, water vapour or

excessive heat.

• These can have adverse effects on Wide Plasma Display operation, and fire or electric shocks

may result.

Do not install the Wide Plasma Display face up, sideways or upside down.

• Doing so may cause heat to build up inside the display, and fire may result.

Two people are required to install and remove the display.

• If two people are not present, the display may be dropped, and personal injury may result.

Maintain a space of at least 10 cm 3

15

/

16

inches at the top, bottom and sides of the

display, and at least 1.9 cm (

3

/4 inches) at the rear of the display.

• The display has air outlet holes at the top and air intake holes at the bottom and rear. These

holes must not be covered, otherwise fire may result.

3

English

Components

Points to note during installation

•

The wall-hanging bracket is for use in installing the Wide Plasma Display to a vertical wall

for viewing purposes. Do not use it for any type of installation other than vertical wall

installation.

•

In order to ensure correct, problem-free operation of the Wide Plasma Display, do not

install the Display in any of the following places.

• Places which are next to sprinklers or sensors

• Places which are subject to vibration or shocks

• Places which are close to high-voltage wires or electric motors

• Places in direct contact with air from heaters

•

When installing this wall-hanging bracket unit, use a fixing method appropriate to the type

of wall.

•

Use an M6 bolt (sold separately) appropriate for the type of wall material (wood, steel

frame, concrete, etc.) the bracket is to be mounted on.

•

Keep retention screws and power cord away from any metallic parts or structures within

the wall.

•

Insert the power cord plug for the Wide Plasma Display into a wall outlet which is close

and easily accessible.

•

Provide adequate ventilation so that the temperature around the display does not rise

above 40°C (104 F°). If there is insufficient movement of the air inside display, heat may

build up inside the display, and fire may result.

Wall-hanging bracket unit..................................................1 Allen key (accessory) ......1

M5 screw .........................2

Insulating spacer

....................................4

Toothed pan washer

....................................4

Pan head bolt with

hex socket (M8-45) .........4

(Fixing screw)

4

English

Installation procedure

The wall-hanging bracket weighs approximately 6 kg (13.23 lbs.), and the Wide Plasma Display unit weights

approximately 33 kg (72.8 lbs.) to 45 kg (99.2 lbs.).

While referring to the wall-hanging bracket installation dimensions in the diagram below, check the strength of

the wall in six installation locations, and add reinforcing if any of these locations are not strong enough.

• The wall-hanging bracket has installation holes provided in 24 locations.

if the wall material will not allow sufficient strength to be obtained from using six installation holes, use some of the spare holes.

However, depending on the construction material used at the place of installation, cracks may develop if the screws are

inserted too close to each other.

Note

Installation procedure

First screw a bolt into the center-top

hole.

Use a level gauge to correct the

alignment of the wall-hanging

bracket, and then screw bolts into

the remaining five holes.

Provisionally tighten the fixing screws.

If the screws are inserted more than

5 mm (

13

/

64

inches), it will not be

possible to install the Wide Plasma

Display in the correct position.

1. Check the strength of the installation location.

2. Install the wall-hanging bracket to the wall.

Fixing screw

• Install the Wall-hanging bracket so that the arrow shown on the bracket is pointing upwards.

• If it is necessary to embed bolts or nuts beforehand because the wall is made from concrete, use the bracket

itself to determine the correct installation hole positions, or use the dimension diagram to calculate the hole

positions. Then embed the M6 bolts or nuts into the holes. Furthermore, when embedding the bolts, allow the

bolts to protrude from the wall by 10 mm (

13

/32 inches) to 15 mm (

19

/32 inches).

930 (36

39

/64)

490 (19

19

/64)

450 (17

23

/32)

30

2020

450 (17

23

/32)450 (17

23

/32)

100

50 (1

31

/32)

15 15

Used for routing wires behind a wall

Units : mm

( ) : inches

(

19

/32) (

19

/32)

(3

15

/16)

(

25

/32)(

25

/32)

(1

3

/16)

Wall installation holes (6 locations)

50 (1

31

/32)

• Use commercially-available M6 bolts which suit the wall materials for installation to the wall.

5

English

• Place the display face down on top of a cloth which is clean and free from other foreign particles, and then carry out the

procedure above.

Note

• Do not Lift the display too high, otherwise it may become unhooked.

Note

Installation procedure

Push the upper insulating spacers

on the display into the notches at

the top of the wall-hanging bracket

until they are hooked in, and then

lower the display into place.

While lifting the display slightly,

insert the lower insulating spacers

on the display into the lower

horizontal hanging holes in the wall-

hanging bracket, and then lower the

display.

3. Prepare the Wide Plasma Display.

4. Install the display to the wall-hanging bracket.

Remove the four bolts.

Pan head bolt with hex socket

Toothed pan washer

Insulating spacer

1. Remove the four bolts from the display.

2. Use the accessory tool (Allen key) to

install the four accessory pan head

bolts with hex socket, toothed pan

washers and insulating spacers into the

holes where the four bolts used to be

as shown in the illustration.

• Attach the insulating spacers to the display.

Insulating spacer

Notches (for hanging horizontally)

Lower horizontal

hanging holes

6

English

Installation procedure

5. Secure the Wall-hanging bracket.

6. Removing the display

1. Remove the two fixing screws which

are screwed into the wall-hanging

bracket.

2. While lifting up the bottom of the

display

Pull it forward to detach the

insulating spacers at the bottom

Then lift up the display.

• Tighten the fixing screws at left and

right.

Fixing screw mounts

(left and right)

Wall-hanging bracket

• Be sure to tighten the left and right fixing screws to prevent the display from detaching from the wall-hanging bracket.

Note

Fixing screws

(left and right)

Insulating spacer

7

English

(For U.S.A)

Panasonic Consumer Electronics Company

Division of Matsushita Electric Corporation

of America

One Panasonic Way

Secaucaus, NJ

07094

RACKS AND STANDS

Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the

warrantor” ), will replace parts in case of defects in materials or workmanship, free of change, in the USA or

Puerto Rico, for ten (10) days from the date of the original purchase.

In-warranty parts in the USA can be obtained during the warranty period be contacting:

Panasonic Services Company (PASC)

20421 84th Avenue South

Kent, Washington 98032

Tel.:1-800-833-9626

Fax.:1-800-237-9080

(6 am to 5 pm Monday-Friday; 6 am to 10:30 am Saturday; PST)

Service in Puerto Rico can be obtained during the warranty period by calling the telephone number listed above.

This warranty is extended only to the original purchaser. A purchase receipt or other proof of the original

purchase is required for replacement parts under the warranty.

This warranty only covers failures due to materials and workmanship and does not cover normal wear. The

warranty does not cover damages which occurred in shipment or failures which result from accidents, misuse,

abuse, neglect, mishandling, misapplication, faulty installation, set-up adjustments, improper maintenance,

alteration, line power surge, lightning damage, modification,or commercial use, such as hotel, office,

restaurant, or other business or rental use of the product, or damage that is attributable to acts of God.

LIMITS AND EXCLUSIONS

There are no express warranties except as listed above.

PANASONIC SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGE RESULTING

FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL

EXPRESS AND IMPLIED WARRANTIES. INCLUDING THE WARRANTIES OF MERCHANTABILITY, ARE

LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on

how long an implied warranty lasts, so the above exclusions or limitations may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

If a problem with this product develops during or after the warranty period, you may contact your dealer or call

the number listed above.

If the problem is not handled to your satisfaction, then write to the Customer Satisfaction Center at the

Panasonic Consumer Electronics Company address indicated above.

Panasonic Sales Company, Division of

Matsushita Electric of Puerto Rico, Inc.

AVE. 65 de Infanteria, Km 9.5

San Gabriel Industrial Park

Carolina, Puerto Rico 00985

Warranty

Page is loading ...

Matsushita Electric Industrial Co., Ltd

Web Site : http://www.panasonic.co.jp/global/

Printed in Japan

M0600-2052

(Recycled paper)

Panasonic TYWK42PV1U Operating instructions

Panasonic TYWK42PV1U Operating instructions

in other languages

Related papers

Other documents