2. Andersen
  3. Keeper Retrofit Replacement

Andersen Keeper Retrofit Replacement Service Instructions

  • Hello! I've reviewed the user guide for the Andersen E-Series gliding patio door keeper retrofit replacement. This document provides detailed instructions on how to replace the keeper, including specific guidance for bi-parting doors. I can answer your questions about the tools, steps, and parts involved in replacing the keeper.
  • What tools are needed for the keeper retrofit?
    Is a shim needed for all door types?
    What should I do after installing the keeper?
    What should I do with old keeper?
9138799 BB-00 Revised 11/18/15
Tools Needed
∙Safety Glasses
∙Phillips Screwdriver
Keeper Retrot Replacement
for Andersen® E-Series Gliding Patio Doors Manufactured Before April 2015
Use caution when working at elevated heights and around unit openings.
Follow manufacturers’ instructions for ladders and/or scaffolding. Failure
to do so may result in injury or death.
Follow manufacturers’ instructions for hand or power tools. Always
wear safety glasses. Failure to do so may result in injury and/or
product damage.
Parts Included
(1) Keeper
(1) Keeper Shim (Bi-parting doors only)
Thank you for choosing Andersen.
For questions call 1-888-888-7020. For more information and/or guides visit www.eaglewindow.com.
Please leave this guide with building owner.
▶Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
▶Check with your local building code ofcial to identify and conrm compliance with local building code requirements.
Keeper Shim
(Bi-parting doors only)
Keeper
(Post-April 2015)
“Andersen” and all other marks where denoted are trademarks of Andersen Corporation and its subsidiary. ©2013-2015 Andersen Corporation. All rights reserved.
To be used with the
Post-2015 lock.
Note: Patio doors
equipped with
Verilock® sensors must
use the Pre-April 2015
lock and keeper.
2
9138799
Remove two (2) keeper wood screws and one
(1) machine screw. Save keeper wood screws
for reuse.
Cut template from Page 3 and position on jamb (or panel for bi-parting patio
doors) using upper two screw holes as guides.
Mark and pre-drill three new holes using 3/16" bit for jamb
mounted keepers or 1/8" bit for panel (bi-parting patio
doors) mounted keepers.
2
Interior
Remove keeper and dispose of properly.
3
Interior
Unlock and open operating panel.
Operating Panel
1
Interior
Drill/Driver
Keeper
Screws
Keeper
Machine
Screw
Keeper Wood
Screws
4
Interior
5
Interior
For bi-parting patio doors only, insert shim into keeper before fastening.
6
Interior
Upper two
screw holes.
Template
Pre-drill three
new holes.
For bi-parting
doors only,
insert shim
into keeper
before
fastening.
Keeper
Keeper Shim (Bi-parting patio doors only)
Template can be
held in position
using removed
screws.
Bi-parting Patio Doors Only
8
Interior
Close operating panel and verify lock operation. Adjust keeper up or down as
needed for correct lock operation and fully tighten keeper wood screws.
Test lock
operation.
Adjust as needed.
3
9138799
Fill remaining
screw hole with
putty.
Keeper
Wood
Screws
Fasten keeper center hole using #10 x 3" at head screw. Fill remaining screw
hole with putty.
7
Interior
Close and lock operating panel.
9
Interior
▶Keeper Replacement is complete.
Operating
Panel
For instruction guides that have been printed from
our website and/or from an electronic le, check
measurement of the printed template to make
sure the size has not been altered.
Para las guías de instrucciones que se han impreso
de nuestro sitio web o desde un archivo electrónico,
verique la medida de la plantilla impresa para
asegurarse de que el tamaño no haya cambiado.
This end UP
New Hole
New Hole
New Hole
Existing Hole
Existing Hole
1.500
8.250
8 1/4"
This End Up
New Hole
New Hole
New Hole
Existing Hole
Existing Hole
Keeper
Wood
Screws
Optional third
screw at center
(#10 x 3" flat head
screw by others)
/