Follett U300BR400A/W Operating instructions

Follett
Brand
Follett
Model
U300BR400A/W
Type
Operating instructions

This manual is also suitable for

Operation, Service and Parts Manual
Service Number A23719 to B22204
U300/UD300 Series Ice Dispensers
208782R02
801 Church Lane • PO Box D, Easton, PA 18044, USA
Toll free (800) 523-9361 • (888)2-FOLLETT
(610) 252-7301 • Fax (610) 250-0696 • www.follettice.com
Model UD300
Model U300
Model U300B
Model U300R400A/W
Model U300BR400A/W
Model U300R800A/W
Model U300BR800A/W
Model UD300R400A/W Model UD300R800A/W
Order parts online
www.follettice.com
Single-sided dispensers
Dual-sided dispensers
Welcome to Follett
Follett ice dispensers enjoy a well-deserved reputation for excellent performance, long-term reliability and
outstanding after-the-sale support. To ensure that this dispenser delivers that same degree of service, we ask
that you take a moment to review this manual before using the dispenser. Should you have any questions or
require technical help at any point, please call our technical service group at (800) 523-9361 or
(888) 2-FOLLETT or (610) 252-7301.
Before you begin
Check your paperwork to determine which model you have. Following is an explanation of the different model
numbers in the U300 series.
U300BR400A
Condenser type – A = air-cooled, W = water-cooled
Remote icemaker(s) capacity and refrigerant – 400 = 400 lbs (181kg)/day, R404A
800 = 800 lbs (363kg)/day, R404A
absence of = manual fill unit
B = integral beverage cooling. Absence of a B = no integral beverage cooling.
Approximate storage capacity in lbs
Configuration – U = undercounter single-sided, UD = undercounter dual-sided
Important cautions
• Storage area of dispenser contains mechanical, moving parts. Keep hands and arms clear of this
area at all times. If access to this area is required, power to unit must be disconnected first.
• Follett manual load units accommodate most cube/cubelet ices up to 1" square and Follett
compressed nugget ice. Crushed, flake, bagged or congealed ice cannot be used. Use of these ices
can jam dispenser and void warranty. Separate any “waffle-like” sections of cubes before adding to
dispenser. If you have questions concerning your ice type, call Follett’s customer service group at
(800) 523-9361 or (888) 2-FOLLETT or ( 610) 252-7301.
• Follett recommends use of an activated carbon filter for units equipped with icemakers.
• Ice is slippery. Maintain counters and floors around dispenser in a clean and ice-free condition.
• Ice is food. Follow cleaning instructions to maintain cleanliness of delivered ice.
!
2
3
Electrical Specifications – 115V, 60Hz, 1 phase
Single-sided models
U300 – dispenser 6.0 amps
U300B – dispenser 7.0 amps
U300R400A/W – dispenser 6.0 amps, icemaker 11.0 amps
U300BR400A/W – dispenser 7.0 amps, icemaker 11.0 amps
U300R800A/W – dispenser 6.0 amps, icemakers 11.0 amps each
U300BR800A/W – dispenser 7.0 amps, icemakers 11.0 amps each
Dual-sided models
UD300 – dispenser 8.0 amps
UD300R400A/W – dispenser 8.0 amps, icemaker 11.0 amps
UD300R800A/W – dispenser 8.0 amps, icemakers 11.0 amps each
Note: Each icemaker and dispenser require separate circuit with electrical disconnect within
10 feet (6m). Equipment ground required. Standard electrical – 115V, 60 Hz, 1 phase. Max. fuse
dispenser – 15 amps; each icemaker – 20 amps.
Plumbing
Dispenser – all models
3/4" PVC slip fit bin drain
1" PVC slip fit drain pan drain(s)
1" PVC slip fit beverage bath drain (units with beverage cooling only)
Note: Drains must be hard piped and insulated. Maintain 1/4" per foot (6mm per 304mm) min. slope
Icemaker – automatic load models only
1/4" FPT water in
1/2" MPT drain
3/8" FPT condenser inlet (water-cooled condenser only)
1/2" FPT condenser drain (water-cooled condenser only)
Note: Water disconnect within 10 feet (3m) of icemaker(s) is required for automatic load units
U300 series dispensers with remote icemaker(s) require separate circuit and
disconnect for each icemaker and dispenser.
!
On all models with remote icemaker(s), black wire on icemaker control board
LINE VAC terminal must be moved to 24V terminal.
!
Do not reduce size of drain lines or tie drains together.
!
4
22"
(559mm)
30"
(762mm)
beverage
lines enter
through
bottom
9"
(229mm)
9"
(229mm)
15"
(381mm)
10"
(254mm)
2.5"
(64mm)
7" (178mm)
3" (77mm)
2"
(51mm)
junction
boxes
32.375"
(823mm)
ice waterbath
(U300BR400A/W,
U300BR800A/W,
U300B
only)
3/4"
drain
1"
drains
8.5"
(216mm)
ice
transport
tube entry
27.5"
(699mm)
entrance
beverage
lines
electric
conn.
17"
(432mm)
12" min
(305mm)
6" min
(153mm)
one icemaker –
models U300R400A/W
U300BR400A/W
two icemakers –
models U300R800A/W
U300BR800A/W
40.875
(1039mm)
54.875"
(1394mm)
25.25"
(642mm)
29.625"
(753mm)
ICE
disp.
drains
18.875"
(480mm)
dispenser only
with no icemaker
model U300/U300B
U300 series single-sided dispensers
Front view
Side view – ice dispense chute
Required clearances:
• 60" (1524mm) for installation
• 49" (1245mm) for auger removal
12.125"
(308mm)
30"
(762mm)
8.5"
(216mm)
9"
(229mm)
9"
(229mm)
15"
(381mm)
27.5"
(699mm)
2.5"
(64mm)
2"
(51mm)
3/4"
drain
ice
tube
entry
32.375"
(823mm)
1"
drains
8.5"
(216mm)
beverage
lines exit
through
bottom of
chase
27.5"
(699mm)
10"
(254mm)
alt. ice
transport
tube entry
13.25"
(337mm)
13.25"
(337mm)
electric
conn.
electric
conn.
18.875"
(480mm)
17"
(432mm)
12" min.
(305mm)
6" min.
(153mm)
dispenser with one icemaker
models UD300R400A/W
dispenser with two icemakers
Models UD300R800A/Wm
disp.
drains
43.875
(1115mm)
54.875"
(1394mm)
25.25"
(642mm)
29.625"
(753mm)
ICE
beverage
lines exit
through
bottom of
chase
12" min.
(305mm)
dispenser only with no
icemaker
model UD300
UD300 series dual-sided dispensers
Side view - ice dispense chute
Front view
Side view opposite ice dispense chute
Required clearances:
• 60" (1524mm) for installation
• 49" (1245mm) for auger removal
5
To start up and operate dispenser
1. Follow all cleaning and start-up instructions in U300 Installation Manual packed with dispenser before operating
dispenser.
2. Turn power switches located under dispenser top to ON position.
3. For manual load models, remove drain pan and fill storage area with compatible ice. (See caution on page 2 of
this manual concerning ices which may be used in this dispenser.)
4. For automatic fill models, turn icemaker (bin signal) switch(es) located inside dispenser top to ON position and begin
to make ice.
5. When dispenser has at least 6" (153mm) of ice in storage area, press lever or button to ensure that dispenser is
operating properly.
How dispenser works
Follett’s single-sided U300 series and dual-sided UD300 series ice dispensers are available in manual load
configurations (using ice from another source) or automatic load configurations (fed from one or two Follett 400 lb/day
remote icemakers). An ice water bath beverage cooling system located directly behind valves is available for single-sided
U300 series dispensers. Dual-sided units must use a separate mechanical cooling system to cool beverage lines.
In all models, ice is stored below counter in dispenser storage area. When dispense lever or button is pushed, dispense
motor is activated. This causes wheel assembly in storage area to rotate counterclockwise, moving ice to vertical auger
assembly. Vertical auger carries ice up to dispense chute where it drops by gravity into container.
In automatic load models, ice is manufactured in either one or two Follett remote icemakers. These icemakers may be
located up to 20 ft (3m) away from dispenser. As water freezes to inside walls of icemaker evaporator, a rotating stainless
steel auger removes ice and carries it to top of evaporator assembly where it is compressed and extruded through an
outlet port. The extruded ice is then pushed through tube to storage compartment of dispenser. A bin thermostat shuts off
icemaker when storage compartment is full.
Periodic cleaning of dispenser
Solution A: Prepare cleaning solution (200 ppm available chlorine content) of Ecolab Mikro-chlor Cleaner or
equal chlorinated detergent. Solution temperature must be at 75˚ – 125˚F (23˚ – 52˚C).
Solution B: Prepare sanitizing solution (50 ppm available chlorine content) of Ecolab Mikro-chlor Cleaner or
equal chlorinated detergent. Solution temperature must be at 75˚ – 125˚F (23˚ – 52˚C).
Recommended daily cleaning of drain pan
1. Remove all debris from drain pan.
2. Pour 1 gallon (4L) hot water into drain pan to keep drain lines clear.
Recommended weekly cleaning
1. Remove drain pan(s) and grille(s) and wash with Solution A above. Rinse thoroughly.
2. On units with beverage valves, remove nozzles and diffusers from valves, soak for at least 10 minutes in cleaning
Solution A, rinse, sanitize with Solution B and reinstall.
3. Pour a solution of one cup (8 oz/237ml) household bleach mixed with one gallon (3.8L) hot water into drain pan(s) to
help prevent algae growth in drain lines.
Recommended quarterly cleaning (every 3 months)
1. Empty all ice from dispenser.
2. Remove dispenser top and turn bin signal switch(es) and dispenser power switch to OFF position.
3. Remove dispenser drain pan(s) and grille(s).
4. Remove thumbscrews from splash panel, lift up and out at bottom of panel and remove.
5. Remove chute cover(s), dispense chute(s), auger tube and auger (see disassembly instructions).
6. Remove yoke rods, drive shaft and dispense wheel (see disassembly instructions).
7. Clean all components and bin storage area with Solution A, rinse thoroughly with clear water and sanitize with
Solution B. Caution: To avoid damage to switch, do not immerse chute cover in solution. Wipe only with
cleaning cloth.
6
Do NOT run plastic parts (drain pan, dispense chute cover, dispense wheel) through
a dishwasher.
!
8. On units with beverage valves, remove nozzles and diffusers from valves, soak for at least 10 minutes in cleaning
Solution A, rinse, sanitize with Solution B and reinstall.
9. For models with integral ice water bath beverage cooling only:
a. Lower Tygon drain tube found on drain connection side of waterbath into PVC waterbath drain and drain ice
water bath.
b. Wash bath interior and components with Solution A, using a bottle brush to clean coils.
c. Reposition Tygon waterbath drain line in UP position.
d. Fill waterbath with Solution A and turn power back on.
e. Allow pump to run for 2 minutes to clean pump and pump lines.
f. Turn power OFF, drain bath and secure tube in UP position.
Putting unit back in service after quarterly cleaning
1. On units with integral beverage cooling, fill ice water bath manually with potable water. Add ice slowly enough to
avoid spillage over top of waterbath.
2. Reassemble components.
3. For manual load units, turn dispenser power switch to ON position and fill unit with approved ice (see caution
statement page 2).
4. For automatic load units, turn bin signal switch(es) and dispenser power switch to ON position and allow storage
area to fill.
5. When dispenser has at least 6" (153mm) of ice in lower storage area, press dispense button or lever to test that
dispenser is functioning properly.
Quarterly cleaning of icemaker system
Disassembly instructions for periodic cleaning
Dispense chute cover removal
1. Remove dispenser top cover and turn three switches on electrical box OFF.
2. Remove two Phillips head screws from top of black dispense chute cover.
3. Pull chute cover forward and down to remove.
4. On push-button actuated units, disconnect plug on harness.
7
dispense chute cover
(dispense mechanism
behind cover)
dispenser top cover
(electrical box below)
splash
panel
dispense
tower (auger
and auger
tube inside)
Front view
drain
pan
Units with an icemaker require that icemaker be cleaned at least every three months
or more often if local water conditions dictate. Failure to clean icemaker system will
result in decreased performance and potential damage to icemaker. Refer to Icemaker
Operation and Service Manual for instructions.
!
Gate assembly removal
1. Remove black dispense chute cover.
2. Remove thumbscrews on each side of focus chute and remove.
3. Remove quick release pins holding dispense gate assembly
and chute.
4. Lift gate up and over hinge tabs, then carefully pull and tilt to
unhook from solenoid link.
5. Pull ice chute toward you to unclip from dimples on chute
mounting bracket.
6. Pull ice chute and gate toward you and out through panel opening.
Auger and auger tube removal
1. Remove black dispense chute cover, focus chute, dispense chute
and gate assembly.
2. Remove drain pan.
3. Remove thumbscrews from splash guard and remove.
4. Remove thumbscrews from splash panel; lift and pull forward at base
of panel and remove.
5. Unplug auger motor at electrical box.
6. Remove two 1/4-20 bolts holding auger motor to holddown
bracket.
7. Remove two thumbscrews from auger motor stabilizer bracket
and aside.
8. Lift auger motor off.
9. Remove dispense chute mounting bracket assembly.
10. Remove side panel of tower.
11. Remove screw holding top auger tube ring to lower ring.
12. Lift auger out of auger tube.
13. Lift out auger tube, turning as needed to clear rivnuts on side
auger motor mounting bracket.
Dispenser wheel removal
1. Remove dispenser top and turn power
switch OFF.
2. Remove drain pan and ice bin access
cover below it.
3. Remove splash guard and wheel motor access cover.
4. Remove all ice from bin.
5. Unplug wheel motor at electrical box and remove ground wire.
5. Remove wheel motor by
pulling out two quick release pins.
6. Lift drive shaft up through
hole in countertop.
7. Lift dispense wheel out
through drain pan opening.
8
auger motor
wheel motor
auger tube
auger
drive
shaft
U300 cutaway – front view
Dispense chute assembly
quick release pins
ice chute
gate assembly
gate assembly
ice chute
springs
fixed yoke
rods with
brackets (front
rod is lowest)
fixed ramped
yoke rod with
bracket (below
rotating drive
bar)
mounting
bracket
auger
tube ring
Front
9
GND
L1
L2
CONTROL BOARD
QC1
QC2
QC3
PUMP
WM
AM
QC9
QC10
QC11
QC4
QC5
QC6
QC7
QC8
CONTROL BOARD
QC21
QC18
SOL
BATH
BATH
SENSOR
QC15
QC14
QC22
QC17
SOL
DISP
BATH
SOL
SOL
DISPENSE
24 VAC
24 VAC
DISP
SWITCH
V V V V V V V V V V
JUNCTION BOX JUNCTION BOX
BLACK
BLACK
BLACK
PL13
GREEN
PL13
GREEN
GREEN
POWER
SWITCH
BLACK
BLACK
BLACK
PL13
WHITE
BLACK
WHITE
WHITE
WHITE
WHITE
WHITE
PL9
PL1
PL2
PL9
PL1
PL2
L1
L2
PUMP
WM
AM
TRANSFORMER
PRIMARY
SECONDARY (24V)
BLUE
RED
BLUE BLUE
BLUE
RED
RED
RED
BLUE
BLUE
RED
RED
YELLOW
PL12PL12
PL3
PL3
PL10
PL4
PL4
PL6
PL6
PL10
QC
QC
DRAIN PAN
SWITCH
DISPENSE
SWITCH
(PB OR LEVER)
TRAN
TRAN
TRAN
TRAN
TRAN
TRAN QC22
QC17
BEVERAGE VALVES
RED
BLUE
BLUE RED
REDBLUE
BLUEBLUE
BLUE
BLUE
YELLOW YELLOW
PL7
PL8
PL7
PL8
PL14
PL14
KEY
SWITCH
ACCESSORY
DRAIN PAN
SWITCH
T'STAT
1
2
IM#1
BIN
BLUE
BIN SIGNAL
SWITCH IM#2
BIN SIGNAL
SWITCH IM#1
24V JB
24V JB
SIGNAL
IM#1
BIN
SIGNAL
INPUT POWER
Wiring diagram
Single-sided models with a service number of 5012607 or higher or any model with
BLUE circuit board
Temperature lights
Temperature lights
provide information on
the status of the ice-
waterbath. When lighted,
the following LEDs
indicate:
Low LED: Bath is at
optimal temperature for
cold drinks.
High LED: Bath
temperature is above
optimal temperature. The
bath will fill with ice for 15
seconds and will then
stop for 75 seconds. If
temperature is still too
high, cycle will repeat.
Error and Low LEDs:
After 15 minutes of fill
cycling, bath is above
40˚F (4.4˚C).
Error (flashing) LED:
Board not receiving
signal from sensor.
GND . . . .
PL . . . . . .
AM
WM . . . . .
QC . . . . .
SOL . . . .
DISP . . .
IM . . . . . .
TRAN . . .
WHEEL MOTOR
QUICK CONNECT
TRANSFORMER
SOLENOID
PLUG
GROUND
DISPENSE
ICE MAKER
AUGER MOTOR
LEGEND
JB . . . . . .JUNCTION BOX
T'STAT . .
THERMOSTAT
PB . . . . . .PUSH BUTTON
. . . . .
Wiring diagram – all dual-sided models
L1
INPUT POWER
GREEN
PL13
GREEN
BLK
PL13
POWER
SWITCH
WHITE
PL12
L2
PL13
WHITE
WHITE
TB
4
R1
PL2
PL4
BLUE
PL2
PL1
TRANSFORMER 1
PRI
R
C
SEC
24V
RED
PL3
PL3
BLUE
YELLOW
YELLOW
BLUE
RED
DISPENSE
SWITCH #1
(PB OR LEVER)
AB
R1
TRANS.1
(C)
JUNCTION BOX
JUNCTION BOX
TRANS.1
(C)
SAFETY
SWITCH #1
(DP-NO)
QC
QC
KEY
SWITCH
ACCESSORY
BLACK
V
V V V V
V V V V V
SODA VALVES – SIDE 1
BLUE
BLK
PL10
PL10
RED
R1
(B)
BIN
STAT
(1)
TRANS.1
(R)
BLUE
T-STAT
1
2
BLUE
BIN SIGNAL
SWITCH IM#1
IM #1
BIN
SIGNAL
PL7
PL7
BLUE
YEL
BIN SIGNAL
SWITCH IM#2
IM #2
BIN
SIGNAL
PL8
BLUE
BLUE
BLUE
BLUE
24V J.B.
24V J.B.
GND
BLK
BLK
TB
BLK
SAFETY
SWITCH
#1
(DP-NO)
BLK
BLK
SAFETY
SWITCH
#2
(DP-NO)
BLK
PL12
BLK
7
PL1
WM
WHT
WHT
BLK
RED
4
R2
7
WHT
AM
BLK
BLK
BLK
TB
TB
R1
(6)
6
9
R1
BLUE
BLUE
DISPENSE
SOLENOID #1
PL4
TRANS.1
(R)
YEL
RED RED
QC
TRANS.1
(C)
PL8
RED
TRANSFORMER 2
PRI
R
C
SEC
24V
TB
TB
BLUE
YELLOW
YELLOW
BLUE
RED
DISPENSE
SWITCH #2
(PB OR LEVER)
AB
R2
R2
(6)
TRANS.2
(C)
RED
6
9
BLUE
BLUE
DISPENSE
SOLENOID #2
TRANS.2
(R)
R2
(B)
PL5
R2
SAFETY
SWITCH #2
(DP-NO)
QC
QC
KEY
SWITCH
#2
BLACK
V
V V V V
V V V V V
SODA VALVES – SIDE 2
BLUE
BLK
PL11
RED
PL11
ACCESSORY
TRANS.2
(R)
TRANS.2
(C)
BLACK
BLACK
WHITE
PL6
PL6
PL5
S
S
10
11
Symptom
Ice does not dispense when switch
is actuated.
• Auger motor does not run
• Wheel motor does not run
• Gate does not open
Ice does not dispense.
• Auger motor runs
• Wheel motor runs
• Gate does not open
Ice does not dispense.
• Auger motor does not run
• Wheel motor runs
Ice does not dispense.
• Auger motor runs
• Wheel motor does not run
Warm drinks or soda foaming.
Possible cause
1. Power switch faulty or in OFF position;
loose connection.
2. Faulty dispense switch.
3. Faulty transformer/tripped breaker.
4. Faulty fill board.
5. Drain pan ajar.
6. Faulty drain pan safety switch.
1. Loose electrical connection.
2. Linkage problem between solenoid
and gate.
3. Faulty solenoid.
4. Faulty fill board.
1. Loose electrical connection.
2. Faulty auger motor.
3. Faulty run capacitor.
1. Loose electrical connection.
2. Faulty wheel motor.
3. Faulty run capacitor.
1. No ice in storage bin.
2. Water drained out of ice-waterbath.
3. Faulty circulating pump.
4. Faulty bath solenoid.
5. Faulty thermistor.
Solution
1. Turn power switch to ON, check
connections.
2. Replace switch.
3. Replace transformer/reset
breaker.
4. Replace fill board.
5. Check pan and reseat.
6. Replace switch.
1. Check connections.
2. Check linkage.
3. Replace solenoid.
4. Replace fill board.
1. Check connections.
2. Check auger motor.
3. Check run capacitor.
1. Check connections.
2. Check wheel motor.
3. Check capacitor.
1. Fill storage area with ice or
check icemaker operation. Push
reset on board.
2. Check that ice-waterbath drain
tube is in fixed upright position.
Push reset on board.
3. Check pump. Push reset on
board.
4. Replace bath solenoid. Push
reset on board.
5. Replace thermistor.
Dispenser troubleshooting guide
If problem persists after following this basic troubleshooting guide, call Follett's
technical service department at (800) 523-9361 or (888) 2-FOLLETT.
Service and parts
Before calling for service
1. Check that ice is in the dispenser and that congealed cubes are not causing a jam.
2. Check that circuit breaker and switches are in ON position.
3. Check that drain pan(s) are on securely. If ajar, neither dispenser nor valves will operate.
4. Check that all drains are clear.
For units equipped with Follett compressed nugget icemaker, see Icemaker Operation and Service
Manual for service and troubleshooting information.
12
Disassembly instructions for service requirements only – NOT required for
any cleaning procedure.
Ice water bath pump motor removal
1. Disconnect electrical wires to pump.
2. Remove two screws anchoring pump motor bracket
to water bath.
3. Loosen hose clamp on 1" (26mm) Tygon hose at
pump and pull hose free of pump motor.
4. Slide motor and bracket toward center of dispenser
and lift to remove.
Beverage valves not operating.
Ice dispenses without
actuation.
No ice in dispenser.
1. Faulty 24V transformer.
2. Power switch faulty or in OFF position.
3. Drain pan switch faulty or not
depressed.
4. Beverage key switch locking out access.
1. Front ice gate stuck open.
2. Faulty rear solenoid.
3. Faulty pump/faulty bath temperature
sensor.
4. Linkage pin dislodged or broken.
5. Ice jam in rear chute.
6. Misplaced bath sensor causing jam of
rear chute.
7. Wire off rear solenoid causing ice to
dispense out front when filling bath,
without actuation.
1. Power switch in OFF position or faulty.
2. Bin signal switches in OFF position or
faulty.
3. Faulty bin thermostat.
4. Faulty transformer.
5. Icemaker related problem.
6. Faulty or disconnected wiring.
1. Check transformer & circuit
breaker.
2. Check power switch.
3. Check switch and placement of
drain pan.
4. Check valve lockout.
1. Adjust gate (contact Follett)
2. Replace solenoid.
3. Replace pump or bath sensor.
4. Check pin and reseat or replace if
broken.
5. Clear ice jam from chute.
6. Remount bath sensor in proper
location.
7. Reconnect wire.
1. Check switch and replace if
necessary.
2. Check switch and replace if
necessary.
3. Replace bin thermostat.
4. Replace transformer.
5. Refer to icemaker Operation and
Service Manual for diagnosing.
6. Check for power and bin signal on
icemaker pc board.
drain
hose
pump
Plan view ice water bath
bath sensor
Symptom
Possible cause
Solution
Parts
ICE
ICE
Reference # Description Part #
1 Lid, with graphics, single-sided 501930
2 Lid, with graphics, dual-sided 501931
3Graphics, “Follett” 501938
4 Access panel, tower, single-sided 501944
5 Access panel, tower, dual-sided 501945
Not shown Cover, ice opening (below drain pan) 501934
6 Drain pan assembly and grille 501935
7 Drain pan, plastic 501936
Not shown Switch, drain pan safety 501318
8Grille, drain pan 501937
9 Chute cover, dispense, push-button with switch 501957
Not shown Chute cover, dispense, lever 501956
10 Splash guard 501943
11 Thumbscrew, 10/32-1/2, splash guard 501100
Not shown Switch, dispense, PB 502441
Not shown Switch, dispense lever (includes boot and spacer) 501714
Not shown Boot, dispense switch button, lever 501841
Not shown Access cover, wheel motor (behind splash guard) 501932
Not shown Skid 501946
Not shown Carton and fillers 501947
Not shown Lip kit (plastic strip bordering ice bin opening and adhesive) 502285
Not shown Insulation, transport tube (sold by the foot) 501176
Not shown Tube, ice transport, 10 ft 502522
Not shown Tube, ice transport, 20 ft 502523
Not shown Plug 2 lead, male 502333
Not shown Plug 2 lead, female 502334
ICE
ICE
1
2
3
3
4
5
6
6
7
8
9
9
1
Plan view
10
10
13
11
11
11
Single-side dispenser
Dual-side dispenser
7
7
1
2
8
10
3
5
4
6
9
11
12
13
14
countertop
section
4
Top view
lower ring
Top view
auger tube seal
Front view
auger tube
6
Reference # Description Part #
1 Motor, auger (includes capacitor) 501984
2 Bracket, auger motor hold-down 502047
Not shown Bracket, auger motor stabilizer, single-sided models 502060
Not shown Bracket, auger motor stabilizer, dual-sided models 502113
Not shown Seal, shaft, auger motor 501977
3 Auger 501980
4 Auger tube (includes insulation) 502631
5 Insulation, auger tube 502099
6 Ring, auger tube, upper 501939
7 Ring, auger tube, lower 502155
8 Motor, wheel, Brother (includes capacitor) 502657
9 Bracket, wheel motor 501981
Not shown Capacitor, wheel motor, Brother 502658
Not shown Gasket, wheel motor bracket 501982
Not shown Pin, quick release, wheel motor (2 required) 502102
10 Drive shaft assembly, for Brother motor 502630
11 Agitator rods, fixed, front and back 502629
12 Wheel, dispense 501978
13 Bearing plate, bottom auger 501971
Not shown Bearing, bottom, auger 501972
Not shown Agitator rod, ramped 502628
Not shown Bracket, fixed agitator (3 used per unit) 501974
Not shown Thumbscrew, 10/32 x 3/4, fixed agitator bracket (2 required) 501259
14 Tee, drain 502059
15 Thermostat box (includes 500514) 502211
Not shown Thermostat 500514
Not shown Retainer, ice hose (includes 2 thumbscrews) 501764
16 Bracket, ice hose and wheel motor 502050
7
14
5
16
reinforcing
tab
15
U300 dispense assembly
side view
U300 dispense assembly
top view
2
1
4
1
4
6
3
3
7
Reference # Description Part #
1 Manifold, carbonated water (bev. cooled units) 502002
2 Syrup coil 501962
3 Waterbath ice guide assembly 502001
4 Bath sensor 502208
5 Bracket, bath sensor 502210
6 Pump, waterbath 501964
Not shown Manifold, carbonated water (single-side, non-beverage cooled units) 501968
Not shown Tubing, vinyl, 1/2" (13mm) ID x 5/8" (17mm) OD (order by the
foot – 5 feet required for bath, 2 feet required for overflow) 501965
Not shown Tubing, vinyl, pump (order by the foot – 3 feet required) 501966
Not shown Syrup tube, insulated, non-bev. cooled units) 501967
Not shown Cap, carbonated water manifold valve fitting 502062
Reference # Description Part #
1 Gate, dispense 501955
2 Linkage pin, gate/solenoid 502096
3 Pin, quick release, 3" (77mm), gate and lever 501949
4 Chute, ice 501952
5 Solenoid 501961
Not shown Boot, solenoid 502098
6 Dispense mechanism assembly 501948
7 Spring, dispense mechanism (1 per side) 501950
Not shown Chute, focus 501954
Not shown Lever, dispense 501953
2
1
6
3
15
5
4
5
Electrical box
All UD300 dual-sided models
Reference # Description Part #
1 Relay, 24V 501826
2 Transformer, 65VA 502058
3 Control box, dual-side models 502049
4Thermostat 500514
5 Switch, rocker 502209
Not shown Bracket, electric box support 502113
Not shown Keylock switch with leads 501960
Not shown Key, beverage, lock switch 501286
1
2
3
4
5
Electrical box
Single-sided models with BLUE circuit board
RESET
POWER
Reference # Description Part #
1Control board (blue) 502207
2 Stand-off 501959
3 Transformer, 65VA 502058
4 Switch, rocker 502209
5 Control box (includes all components) 502212
Not shown Keylock switch with leads 501960
Not shown Bracket, electric box support 501933
Not shown Thermostat (located behind splash panel in thermostat box) 500514
Not shown Key, beverage, lock switch 501286
1
2
4
3
5
208782R02
02/03
801 Church Lane • PO Box D, Easton, PA 18044, USA
Toll free (800) 523-9361 • (888)2-FOLLETT
(610) 252-7301 • Fax (610) 250-0696 • www.follettice.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Follett U300BR400A/W Operating instructions

Follett
Brand
Follett
Model
U300BR400A/W
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents