HDMI CONNECTION TO ZONE 2
PLAYING THE SAME VIDEO/AUDIO IN BOTH ZONES. .....2
HDMI CONNECTION TO ZONE 2
PLAYING DIFFERENT VIDEO/AUDIO IN EACH ZONE. .....3
PRE-OUT CONNECTION TO ZONE 2
PLAYING THE SAME AUDIO IN BOTH ZONES. .....................4
PRE-OUT CONNECTION TO ZONE 2
PLAYING DIFFERENT AUDIO IN EACH ZONE. ....................5
SPEAKER CONNECTION TO ZONE 2
PLAYING THE SAME AUDIO IN BOTH ZONES. .....................6
SPEAKER CONNECTION TO ZONE 2
PLAYING DIFFERENT AUDIO IN EACH ZONE. ....................7
TABLE OF CONTENTS
ZONE 2 SETUP GUIDECXR200
ZONE 2 SETUP GUIDECXR200
2
1
Switch on Zone 2
– Using the remote: Press and hold the Zone 2 button, then press the Standby button.
– Using the Cambridge Connect app.
– On the front panel: Press the Zone 2 button (Zone 2 will be shown on the display), then press
the Standby button.
– In the Zone 2 Settings menu within the OSD: Zone 2 Power On.
2
Setting the Zone 2 Source to ‘Follow Main Zone’ will ensure that any video/audio (multi-
channel or stereo) that is playing in the Main Zone will be duplicated and sent to Zone 2.
CXR Setup Menu
Speaker Setup
Input Setup
Zone 2 Settings
Network Setup
General Settings
HDMI Output Setup
Advanced Setup
Zone 2 Power
Zone 2 Source
Zone 2 Power On Volume
On
Follow Main Zone
- 30 dB
Any multi-channel audio source (eg. Blu-ray movie) playing in the Main Zone will be sent to the
Zone 2 TV as a 2CH PCM (stereo) downmix when Follow Main is selected.
Notes:
• Using HDMI connection for Zone 2 you will be using the TV in Zone 2 to play the audio and
video. The TV must have speakers.
• When using Follow Main, the same audio will be heard in both zones. Whatever source is
selected in the Main Zone will be repeated as stereo in Zone 2. This means that any source can
be heard in Zone 2.
ZONE 2
HDMI CONNECTION TO ZONE 2
PLAYING THE SAME VIDEO/AUDIO IN BOTH ZONES.
HDMI
Up to 7.2 speaker connection
HDMI
MAIN ZONE
ZONE 2 SETUP GUIDE ZONE 2 SETUP GUIDECXR200
3
1
Switch on Zone 2:
– Using the remote: Press and hold the Zone 2 button, then press the Standby button
– Using the Cambridge Connect app
– On Front panel: press the Zone 2 button (Zone 2 will be shown on the display), then press the
Standby button
– In the Zone 2 Settings menu within the OSD: Zone 2 Power On
2
The Zone 2 source can be selected using the remote control, front panel, app and the Zone
2 Settings menu.
CXR Setup Menu
Speaker Setup
Input Setup
Zone 2 Settings
Network Setup
General Settings
HDMI Output Setup
Advanced Setup
Zone 2 Power
Zone 2 Source
Zone 2 Power On Volume
On
Source 3
- 30 dB
Note:
• Using HDMI connection for Zone 2 you will be using the TV in Zone 2 to play the audio and
video. The TV must have speakers.
ZONE 2
HDMI CONNECTION TO ZONE 2
PLAYING DIFFERENT VIDEO/AUDIO IN EACH ZONE.
HDMI
Up to 7.2 speaker connection
HDMI
MAIN ZONE
ZONE 2 SETUP GUIDECXR200
4
1
Switch on Zone 2
– Using the remote: Press and hold the Zone 2 button, then press the Standby button.
– Using the Cambridge Connect app.
– On the front panel: Press the Zone 2 button (Zone 2 will be shown on the display), then press
the Standby button.
– In the Zone 2 Settings menu within the OSD: Zone 2 Power On.
2
Setting the Zone 2 Source to ‘Follow Main Zone’ will ensure that any audio (multi-channel or
stereo) that is playing in the Main Zone will be duplicated and sent to Zone 2.
CXR Setup Menu
Speaker Setup
Input Setup
Zone 2 Settings
Network Setup
General Settings
HDMI Output Setup
Advanced Setup
Zone 2 Power
Zone 2 Source
Zone 2 Power On Volume
On
Follow Main Zone
- 30 dB
Any multi-channel audio source (eg. Blu-ray movie) playing in the Main Zone will be sent to Zone
2 as a 2CH PCM (stereo) downmix when Follow Main is selected
Notes:
• When using Follow Main, the same audio will be heard in both zones. Whatever source is
selected in the Main Zone will be repeated as stereo in Zone 2. This means that any source can
be heard in Zone 2.
• It is not possible to congure the second subwoofer output for Zone 2 use.
ZONE 2
PRE-OUT CONNECTION TO ZONE 2
PLAYING THE SAME AUDIO IN BOTH ZONES.
Up to 7.2 speaker connection
HDMI
MAIN ZONE
ZONE 2 SETUP GUIDE ZONE 2 SETUP GUIDECXR200
5
ZONE 2
Up to 7.2 speaker connection
HDMI
MAIN ZONE
1
Switch on Zone 2:
– Using the remote: Press and hold the Zone 2 button, then press the Standby button
– Using the Cambridge Connect app
– On Front panel: press the Zone 2 button (Zone 2 will be shown on the display), then press the
Standby button
– In the Zone 2 Settings menu within the OSD: Zone 2 Power On
2
The Zone 2 source can be selected using the remote control, front panel, app and the Zone
2 Settings menu.
CXR Setup Menu
Speaker Setup
Input Setup
Zone 2 Settings
Network Setup
General Settings
HDMI Output Setup
Advanced Setup
Zone 2 Power
Zone 2 Source
Zone 2 Power On Volume
On
Source 3
- 30 dB
When setting the Zone 2 Source to any source that is dierent from the main zone, only sources
with a 2CH PCM (stereo) audio signal are output to Zone 2.
Notes:
• In Zone 2, to watch/listen to a dierent source to the Main Zone, then the Zone 2 source must
be stereo.
• The FM/AM Tuner and Stream Magic Sources are stereo and can always be played in Zone 2.
If a source is set to use audio from an analogue input, or a digital input as 2CH PCM, then this
can also be played in Zone 2 whilst a dierent source is being played in the Main Zone.
• A source using audio from HDMI or a digital input must be set to 2CH PCM to be played in Zone
2 whilst a dierent source is playing in the Main Zone
• When Zone 2 is On, the HDMI 2 output is also set to Zone 2. It is not possible to use the twin
HDMI outputs for dual (mirrored) displays when Zone 2 Power is On (unless using the Follow
Main feature).
• It is not possible to congure the second subwoofer output for Zone 2 use.
PRE-OUT CONNECTION TO ZONE 2
PLAYING DIFFERENT AUDIO IN EACH ZONE.
ZONE 2 SETUP GUIDECXR200
6
1
Switch on Zone 2
– Using the remote: press and hold the Zone 2
button, then press the Standby button
– Using the Cambridge Connect app
– On Front panel: press the Zone 2 button
(Zone 2 will be shown on the display), then
press the Standby button
– In the Zone 2 Settings menu within the OSD:
Zone 2 Power On
2
Ensure the Back Amp channels are set to
‘Zone 2’ in the Speaker Setup.
CXR Setup Menu
Speaker Setup
Input Setup
Zone 2 Settings
Network Setup
General Settings
HDMI Output Setup
Advanced Setup
Speaker Configuration
Auto Setup
Unit
SW Selection
Back Amp Configuration
►
►
Metres
Subwoofer1+Subwoofer2
Zone 2
3
Setting the Zone 2 Source to ‘Follow Main
Zone’ will ensure that any audio (multi-
channel or stereo) that is playing in the Main
Zone will be duplicated and sent to Zone 2.
CXR Setup Menu
Speaker Setup
Input Setup
Zone 2 Settings
Network Setup
General Settings
HDMI Output Setup
Advanced Setup
Zone 2 Power
Zone 2 Source
Zone 2 Power On Volume
On
Follow Main Zone
- 30 dB
Any multi-channel audio source (eg. Blu-ray
movie) playing in the Main Zone will be sent to
Zone 2 as a 2CH PCM (stereo) downmix when
Follow Main is selected.
Notes:
• When using Follow Main, the same audio will be heard in both zones. Whatever source is
selected in the Main Zone will be repeated as stereo in Zone 2.
• When congured for Zone 2, the back amp channels cannot be used for bi-amping or 7.2 in the
main zone. 5.2 speaker channels is the maximum speaker conguration in the main zone when
using the zone 2 speaker output.
• It is not possible to congure the second subwoofer output for Zone 2 use.
ZONE 2
SPEAKER CONNECTION TO ZONE 2
PLAYING THE SAME AUDIO IN BOTH ZONES.
Up to 5.2 speaker connection
HDMI
MAIN ZONE
ZONE 2 SETUP GUIDE ZONE 2 SETUP GUIDECXR200
7
1
Switch on Zone 2
– Using the remote: press and hold the Zone 2
button, then press the Standby button
– Using the Cambridge Connect app
– On Front panel: press the Zone 2 button
(Zone 2 will be shown on the display), then
press the Standby button
– In the Zone 2 Settings menu within the OSD:
Zone 2 Power On
2
Ensure the Back Amp channels are set to
‘Zone 2’ in the Speaker Setup.
CXR Setup Menu
Speaker Setup
Input Setup
Zone 2 Settings
Network Setup
General Settings
HDMI Output Setup
Advanced Setup
Speaker Configuration
Auto Setup
Unit
SW Selection
Back Amp Configuration
►
►
Metres
Subwoofer1+Subwoofer2
Zone 2
3
The Zone 2 source can be selected using
the remote control, front panel, app and the
Zone 2 Settings menu.
CXR Setup Menu
Speaker Setup
Input Setup
Zone 2 Settings
Network Setup
General Settings
HDMI Output Setup
Advanced Setup
Zone 2 Power
Zone 2 Source
Zone 2 Power On Volume
On
Source 3
- 30 dB
When setting the Zone 2 Source to any source
that is dierent from the main zone, only
sources with a 2CH PCM (stereo) audio signal
are output to Zone 2.
ZONE 2
Up to 5.2 speaker connection
HDMI
MAIN ZONE
SPEAKER CONNECTION TO ZONE 2
PLAYING DIFFERENT AUDIO IN EACH ZONE.
Notes:
• In Zone 2, to watch/listen to a dierent source
to the Main Zone, the Zone 2 source must be
stereo.
• The FM/AM Tuner and Stream Magic Sources
are stereo and can always be played in
Zone 2. If a source is set to use audio from
an analogue input, or a digital input as 2CH
PCM, then this can also be played in Zone 2
whilst a dierent source is being played in the
Main Zone.
• A source using audio from HDMI or a digital
input must be set to 2CH PCM to be played
in Zone 2 whilst a dierent source is playing
in the Main Zone.
• When congured for Zone 2, the back amp
channels cannot be used for bi-amping or 7.2
in the main zone. 5.2 speaker channels is the
maximum speaker conguration in the main
zone when using the zone 2 speaker output.
• It is not possible to congure the second
subwoofer output for Zone 2 use.
• The TV source (ARC) is only available in Zone
2 when set to Follow Main.
• When Zone 2 is On, the HDMI 2 output is also
set to Zone 2. It is not possible to use the twin
HDMI outputs for dual (mirrored) displays
when Zone 2 Power is On (unless using the
Follow Main feature).
/