Page is loading ...
CXR120/200
AV RECEIVER
2
The process of setting up the CXR is rst to make all the connections to your
speakers and source equipment and then set the unit up via its On-Screen
Display (OSD). There are various settings and adjustments that need to be
made before the CXR can be used.
However before you actually decide which connections to make or perform
any adjustments it is strongly advised that you read through the 'Setup'
section of this manual rst, starting on page 22.
A lot of explanation is included that will help you to choose the right
connection types for your sources.
Before connecting
Contents
Make sure you register your purchase.
Visit: www.cambridgeaudio.com/vip
By registering, you'll be the rst to know about:
• Future product releases
• Software upgrades
• News, events and exclusive oers plus
competitions!
This guide is designed to make installing and using this product
as easy as possible. Information in this document has been
carefully checked for accuracy at the time of printing; however,
Cambridge Audio's policy is one of continuous improvement,
therefore design and specications are subject to change without
prior notice.
This document contains proprietary information protected by
copyright. All rights are reserved. No part of this manual may be
reproduced by any mechanical, electronic or other means, in any
form, without prior written permission of the manufacturer. All
trademarks and registered trademarks are the property of their
respective owners.
© Copyright Cambridge Audio Ltd 2018
For DTS patents, see http://patents.dts.com. Manufactured under
license from DTS Licensing Limited. DTS, DTS-HD, the Symbol,
& DTS and the Symbol together are registered trademarks, and
DTS-HD Master Audio is a trademark of DTS, Inc. © DTS, Inc. All
Rights Reserved.
Manufactured under license from Dolby Laboratories. Dolby,
Pro Logic, and the double-D symbol are trademarks of Dolby
Laboratories.
"HDMI","HDMI logo" and "High-Denition Multimedia Interface"
are trademarks or registered trademarks of HDMI Licensing LLC.
Important safety instructions .................................................................. 3
Limited warranty ...................................................................................... 4
Front panel controls ................................................................................ 5
Rear panel connections ........................................................................... 6
Main remote control ................................................................................ 8
Loudspeaker connections ....................................................................... 9
Analogue audio connections ................................................................. 10
Digital audio connections ...................................................................... 10
HDMI connections ................................................................................. 11
4K video resolution ................................................................................ 11
5.1/7.1 direct in ..................................................................................... 12
Pre out connections .............................................................................. 13
Rec out connections ............................................................................. 13
Front input connections ........................................................................ 14
Aerial connections ................................................................................. 14
Using the tuner ...................................................................................... 14
Presets .................................................................................................. 14
Storing stations for Tuner ................................................................... 14
StreamMagic ...................................................................................... 14
Operating instructions ........................................................................... 15
Selecting the source .............................................................................. 15
Selecting the desired listening mode .................................................... 15
Surround sound modes ......................................................................... 20
DSP modes ........................................................................................... 21
Stereo/Stereo + Sub ........................................................................... 21
Direct .................................................................................................. 21
Multi channel PCM ............................................................................. 21
All channels ........................................................................................ 21
Setup menu ........................................................................................... 21
Speaker setup ....................................................................................... 21
Front left and right speakers .............................................................. 22
Centre speaker ................................................................................... 22
Surround left and right speakers ........................................................ 22
Subwoofer .......................................................................................... 22
Surround back left and right speakers ............................................... 22
Front left and right height speakers ................................................... 22
Speaker conguration ........................................................................ 22
Back Amp Conguration .................................................................... 22
Manually setting speaker size ............................................................ 22
Manually setting speaker delay .......................................................... 23
Manually setting level calibration ....................................................... 23
Manually setting sub crossovers and bass management .................. 24
Speaker Auto setup ............................................................................... 24
Input Setup ............................................................................................ 25
Source Input ....................................................................................... 25
Input Name ......................................................................................... 25
Video Input ......................................................................................... 25
Audio Input ......................................................................................... 25
Stereo Processing .............................................................................. 25
Multichannel Processing .................................................................... 25
Lip sync .............................................................................................. 26
Zone 2 (CXR200 only) ............................................................................ 26
Network Setup....................................................................................... 27
General Settings .................................................................................... 28
Network Standby ................................................................................ 28
HDMI Output Setup ............................................................................... 28
TV ARC (HDMI OUT 1) ....................................................................... 28
Advanced Setup .................................................................................... 29
Network software update ...................................................................... 31
Web administration interface ................................................................. 31
StreamMagic Module ............................................................................ 31
Custom installation (C.I.) use ................................................................. 32
Troubleshooting ..................................................................................... 32
Technical specications ........................................................................ 33
3
CXR120/200
For your own safety please read the following important safety instructions
carefully before attempting to connect this unit to the mains power supply.
They will also enable you to get the best performance from and prolong the
life of the unit:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding-type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided
plug does not t into your outlet, consult an electrician for replacement
of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at
plugs, convenience receptacles and the point where they exit from the
apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for long
periods of time.
13. Refer all servicing to qualied service personnel. Servicing is required
when the apparatus has been damaged in any way, such as the power-
supply cord or plug having been damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE AND OBJECTS
FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON
THIS APPARATUS.
Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat such as sunshine, re or the like.
TO COMPLETELY DISCONNECT THIS APPARATUS FROM THE AC
MAINS, DISCONNECT THE POWER SUPPLY CORD PLUG FROM THE AC
RECEPTACLE. POUR DECONNECTER COMPLETEMENT L'APPAREIL DU
RESEAU D'ALIMENTATION, DECONNECTER LE CORDON D'ALIMENTATION
DE LA PRISE MURALE.
THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN
READILY ACCESSIBLE. LA PRISE DU RESEAU D'ALIMENTATION DOIT
DEMEURER AISEMENT ACCESSIBLE"
Only use the mains cord supplied with this unit.
Important safety instructions
The lightning ash with the arrowhead symbol within an equilateral triangle
is intended to alert the user to the presence of un-insulated 'dangerous
voltage' within the product's enclosure that may be of sucient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance instructions in
the service literature relevant to this appliance.
The symbol on this product indicates that it is of CLASS II (double
insulated) construction.
WEEE symbol
The crossed-out wheeled bin is the European Union symbol
for indicating separate collection for electrical and electronic
equipment. This product contains electrical and electronic
equipment which should be reused, recycled or recovered and
should not be disposed of with unsorted regular waste. Please
return the unit or contact the authorised dealer from whom you purchased
this product for more information.
CE mark
This product complies with European Low Voltage (2006/95/
EC), Electromagnetic Compatibility (2004/108/EC) and
Environmentally-friendly design of Energy-related Products (2009/125/EC)
Directives when used and installed according to this instruction manual.
For continued compliance only Cambridge Audio accessories should be
used with this product and servicing must be referred to qualied service
personnel.
RCM (Regulatory Compliance Mark)
This product meets the Safety, EMC and Radio Communications
requirements of the ERAC and ACMA.
CU-TR Mark
This product meets Russia, Byelorussia and Kazakhstan electronic
safety approvals.
Caution: Hot Surface. Do Not Touch
The top surface over the internal heat sink may become hot when
operating this product continuously. Do not touch hot areas,
especially around the "Hot surface mark" and the top panel.
FCC regulations
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO
OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS
TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER
AUTHORITY TO OPERATE THE EQUIPMENT.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Re-orient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
4
For Wi-Fi connectivity, this device comes supplied with an external Wi-Fi
dongle that plugs into the USB port of your device.
This Wi-Fi dongle has been tested in conjunction with your CXR. It is not
recommended to use any other type of dongle other than the type that has
been supplied.
This device meets all the technical and regulatory requirements of your
region.
Please refer to specic in country information.
FCC Statement
DECLARATION OF CONFORMITY WITH FCC RULES FOR
ELECTROMAGNETIC COMPATIBILITY
We, Cambridge Audio, of Gallery Court, Hankey Place, London SE1
4BB, declare under our sole responsibility that this device,
CXR with Wi-Fi module
to which this declaration relates, complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
Caution: Exposure to Radio Frequency Radiation.
The device shall be used in such a manner that the potential for human
contact during normal operation is minimized.
When connecting an external antenna to the device, the antenna shall be
placed in such a manner to minimize the potential for human contact during
normal operation. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy,
and if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged
to try and correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.
2.4 GHz operation of this product in the USA is hardware limited to channels
1 through 11.
Modications
The FCC requires the user to be notied that any changes or modications to
this device that are not expressly approved by Cambridge Audio, may void
the user's authority to operate the equipment.
Wi-Fi information
Ventilation
IMPORTANT – The unit will become hot when in use. Do not stack multiple
units on top of each other. Do not place in an enclosed area such as a
bookcase or in a cabinet without sucient ventilation.
Ensure that small objects do not fall through any ventilation grille. If this
happens, switch o immediately, disconnect from the mains supply and
contact your dealer for advice.
Please ensure there is ample ventilation (at least 20cm clearance on the top,
side and rear). Do not put any objects on top of this unit. Do not situate it on a
rug or other soft surface and do not obstruct any air inlets or outlet grilles. Do
not cover the ventilation grilles with items such as newspapers, tablecloths,
curtains, etc.
Positioning
Choose the installation location carefully. Avoid placing it in direct sunlight or
close to a source of heat. No naked ame sources, such as lighted candles,
should be placed on the unit. Also avoid locations subject to vibration and
excessive dust, cold or moisture. The unit can be used in a moderate climate.
This unit must be installed on a sturdy, level surface. Do not place in a sealed
area such as a bookcase or in a cabinet. Any space open at the back (such
as a dedicated equipment rack) is ne, however. Do not place the unit on an
unstable surface or shelf. The unit may fall, causing serious injury to a child or
adult as well as serious damage to the product. Do not place other equipment
on top of the unit.
Due to stray magnetic elds, turntables or CRT TVs should not be located
nearby due to possible interference.
Electronic audio components have a running in period of around a week (if
used several hours per day). This will allow the new components to settle
down and the sonic properties will improve over this time.
Power sources
The unit should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power-supply to your
home, consult your product dealer or local power company.
This unit can be left in Standby mode when not in use and will draw <0.5W in
this state. To turn the unit o, switch o at the rear panel. If you do not intend
to use this unit for a long period of time, unplug it from the mains socket.
Overloading
Do not overload wall outlets or extension cords as this can result in a risk of
re or electric shock. Overloaded AC outlets, extension cords, frayed power
cords, damaged or cracked wire insulation and broken plugs are dangerous.
They may result in a shock or re hazard.
Be sure to insert each power cord securely. To prevent hum and noise, do not
bundle the interconnect leads with the power cord or speaker leads.
Cleaning
To clean the unit, wipe its case with a dry, lint-free cloth. Do not use any
cleaning uids containing alcohol, ammonia or abrasives. Do not spray an
aerosol at or near the unit.
Battery disposal
Batteries may contain substances harmful to the environment. Please dispose
of any discharged batteries with due consideration and in accordance with
local environmental/electronic recycling guidelines.
Loudspeakers
Before making any connections to loudspeakers, make sure all power is
turned o and only use suitable cables.
Servicing
These units are not user serviceable. Never attempt to repair, disassemble or
reconstruct the unit if there seems to be a problem. A serious electric shock
could result if this precautionary measure is ignored. In the event of a problem
or failure, please contact your dealer.
5
CXR120/200
Cambridge Audio warrants this product to be free from defects in materials
and workmanship (subject to the terms set forth below). Cambridge Audio will
repair or replace (at Cambridge Audio's option) this product or any defective
parts in this product. Warranty periods may vary from country to country. If
in doubt consult your dealer and ensure that you retain proof of purchase.
To obtain warranty service, please contact the Cambridge Audio authorised
dealer from which you purchased this product. If your dealer is not equipped
to perform the repair of your Cambridge Audio product, it can be returned by
your dealer to Cambridge Audio or an authorised Cambridge Audio service
agent. You will need to ship this product in either its original packaging or
packaging aording an equal degree of protection.
Proof of purchase in the form of a bill of sale or receipted invoice, which is
evidence that this product is within the warranty period, must be presented
to obtain warranty service.
This Warranty is invalid if (a) the factory-applied serial number has been
altered or removed from this product or (b) this product was not purchased
from a Cambridge Audio authorised dealer. You may call Cambridge Audio
or your local country Cambridge Audio distributor to conrm that you have
an unaltered serial number and/or you purchased from a Cambridge Audio
authorised dealer.
This Warranty does not cover cosmetic damage or damage due to acts of
God, accident, misuse, abuse, negligence, commercial use, or modication
of, or to any part of, the product. This Warranty does not cover damage
due to improper operation, maintenance or installation, or attempted repair
by anyone other than Cambridge Audio or a Cambridge Audio dealer, or
authorised service agent which is authorised to do Cambridge Audio warranty
work. Any unauthorised repairs will void this Warranty. This Warranty does not
cover products sold AS IS or WITH ALL FAULTS.
REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY
ARE THE EXCLUSIVE REMEDY OF THE CONSUMER. CAMBRIDGE AUDIO
SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY IN
THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY LAW, THIS
WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND
IMPLIED WARRANTIES WHATSOEVER INCLUDING, BUT NOT LIMITED TO,
THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL
PURPOSE.
Some countries and US states do not allow the exclusion or limitation of
incidental or consequential damages or implied warranties so the above
exclusions may not apply to you. This Warranty gives you specic legal rights,
and you may have other statutory rights, which vary from state to state or
country to country.
For any service, in or out of warranty, please contact your dealer.
Plug tting instructions (UK only)
The cord supplied with this appliance is factory tted with a UK mains
plug tted with a 10 amp fuse inside. If it is necessary to change the fuse,
it is important that a 10 amp one is used. If the plug needs to be changed
because it is not suitable for your socket, or becomes damaged, it should be
cut o and an appropriate plug tted following the wiring instructions below.
The plug must then be disposed of safely, as insertion into a mains socket
is likely to cause an electrical hazard. Should it be necessary to t a 3-pin
BS mains plug to the power cord the wires should be tted as shown in this
diagram. The colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your plug.
Connect them as follows:
The wire which is coloured BLUE must be
connected to the terminal which is marked
with the letter 'N' or coloured BLACK.
The wire which is coloured BROWN must
be connected to the terminal which is
marked with the letter 'L' or coloured RED.
The wire which is coloured GREEN/
YELLOW must be connected to the
terminal which is marked with the letter 'E'
or coloured GREEN.
If your model does not have an earth wire, then disregard this instruction.
If a standard 13 amp (BS 1363) plug is used, a 10 amp fuse must be tted,
or if any other type of plug is used a 5 amp fuse must be tted, either in the
plug or adaptor, or on the distribution board.
Limited warranty
Canada-Industry Canada (IC)
This radio transmitter has been approved by Industry Canada.
This Class B digital apparatus complies with Canadian standard ICES-003.
This device complies with Industry Canada License exempt RSS standard(s).
Operation is subject to the following two conditions.
(1) this device may not cause interference and (2) this device must accept
any interference, including interference that may cause undesired operation
of the device.
The transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Industrie Canada (IC)
Cet émetteur radiophonique a été approuvé par Industrie Canada.
Cet appareil numérique de Classe B est conforme à la norme canadienne
ICES-003. Cet appareil est conforme aux normes RSS exemptes de licence
d’Industrie Canada. Son fonctionnement est soumis aux deux conditions
suivantes :
(1) cet appareil ne doit pas provoquer d'interférence nuisible et (2) cet appareil
doit accepter toute interférence reçue, y compris les interférences pouvant
provoquer un fonctionnement indésirable.
L'émetteur ne doit pas être co-placé ni fonctionner en conjonction avec une
autre antenne ou transmetteur.
Europe-European Union Notice
Radio products with the CE alert marking comply with the R&TTE Directive
(1995/5/EC) issued by the Commission of the European Community.
Compliance with this directive implies conformity to the following European
Norms.
• EN 60950-1 – Product Safety.
• EN 300 328 – Technical requirement for radio equipment.
• EN 301 489 – General EMC requirements for radio equipment.
WARNING: To reduce exposure to electromagnetic radiation, it is advised
that user is situated at least 20cm from the Wi-Fi Antenna during normal
operation.
6
HDMI 7 /
MHL
CX R200
CX R120
HDMI 8/
MHL
Front panel controls
1. Standby/On
Switches the unit between Standby mode (indicated by a dim power LED) and
On (indicated by a bright power LED). Standby is an eco-friendly <0.5W low
power mode. The unit may be left in Standby mode when not in use.
2. Phones
Allows for the connection of stereo headphones with a 6.35mm / ¼" Jack
plug. Headphones with an impedance of between 32 and 600 ohms are
recommended.
Note: Plugging in headphones will automatically mute the speakers and
select a Dolby Headphones output to be created for headphone use.
3. Tuning +/-
Used to tune FM/AM frequencies and skip presets for the built-in Tuner.
4. Direct
Disables any audio processing on the current source.
5. Zone (CXR200 only)
If illuminated, indicates Zone 2 is enabled (on). This button can be used to
enable/disable the Zone 2 function, press this button to display Zone 2 on
the Display followed by the Standby/On button. Pressing the Standby/On
will toggle between On and O. See later section of this manual for more
information.
6. Display
Displays the status of the unit.
7. Source +/-
Press to scroll through the available sources. Also used for character entry.
+/- button to move between character entry.
8. Infrared sensor
Receives IR commands from the supplied remote control. A clear,
unobstructed line of sight between the remote control and the sensor is
required.
9. Menu
Press to enter the Setup menu.
10. Back
In the Setup menu, press to return to the previous menu item.
11. USB / MP3 / HDMI/MHL Inputs
USB – Use to connect a USB storage device or another portable device
containing music les. Music playback via the Cambridge Connect app. 1A
maximum current consumption.
MP3 – This source input allows you to connect a portable audio device such
as an MP3 player directly into the front of the unit using the 3.5mm stereo-
jack (labelled '
'). Select the MP3 input source through the main menu 'Audio
Inputs' or direct MP3 button on the remote to listen to your portable audio
device.
HDMI – MHL (Mobile High-denition Link) compatible. This input is used
to connect to a mobile source device such as a mobile phone or a digital
camcorder.
The combined socket allows either a standard HDMI 1.4 compatible source to
be connected to the CXR or alternatively an MHL device (such as some new
phones) in which case the device can also be charged whilst sending digital
audio/video to the CXR.
Note: To utilise the MHL capability, the source device needs to be MHL
enabled and an MHL cable/adaptor is required.
12. Volume
Use to increase/decrease the level of the sound from the outputs of the CXR.
Also used as Enter button by pushing to select source input and menu items.
Also used for character entry. Rotate to browse through the characters.
1
1
2
2
3
3
9
9
10
10
11
12
11
12
4
4
5
7
86
7
86
7
CXR120/200
Rear panel connections
1. FM / AM aerials
All tuner aerial connections are made here. Refer to the 'Aerial Connections'
section of this manual for more information.
2. Analogue inputs
These inputs are suitable for any 'line level' source equipment such as CD,
DVD/BD players, game consoles etc.
Note: These inputs are for analogue audio signals only. They should not be
connected to the digital output of a CD player or any other digital device.
3. 7.1 Direct in
Connect to a 7.1 or 5.1 source (DVD-A or SACD player etc).
4. Pre out (CXR200 only) / Sub out
These outputs can be used to connect to an external power amplier or an
active subwoofer, etc.
5. Rec out
These output sockets can be connected to a recorder etc.
6, 10 & 13 Zone 2 (CXR200 only)
These independent outputs can be used to connect to a second Zone (i.e. a
room or area separate from the main area). See Zone 2 section in this manual
for details.
7. HDMI inputs
HDMI inputs compatible with the HDMI 2.0 standard, except for MHL/HDMI
input 7 on CXR200 which is HDMI 1.4 only. For more information, see 'Video
Input' section of this manual.
Note: All HDMI 2.0 rear connections (HDMI outputs and the HDMI inputs) are
4K compatible. See later section of the manual.
8. Vent grille
Allows cooling of internal circuitry. DO NOT OBSTRUCT!
9. Digital in
Coaxial – Use a high quality 75 ohm digital RCA cable (not one designed for
normal audio use). This input is suitable for 16-24 bit content up to 192kHz.
Toslink optical – Use a high quality TOSLINK bre optic cable designed
specically for audio use. This input is suitable for 16-24 bit content up to
192kHz.
10. Zone 2 speaker terminals
Independent speaker outputs used for Zone 2. See Zone 2 section in this
manual for details.
11. Bi-amp speaker terminals
Use for bi-amping the front Right and Left speakers if necessary.
www.cambridgeaudio.com
CXR120 AV Receiver
Designed & Engineered in Britain
Assembled in Vietnam
www.cambridgeaudio.com
CXR200 AV Receiver
Designed & Engineered in Britain
Assembled in Vietnam
1
1
4
4
10 11 15
3
3
2
2
5
5
6
7
7
13
9
9
12 14
17 18 21
22
22
16 19
20
20
8
8
15
13
12 14
17 18 21
16 19
8
12. Ethernet
For wired network connection.
13. HDMI outputs
For connection to two TVs or a TV and a projector for instance.
CXR120 – Both outputs show the same content.
CXR200 – Output 2 can display a dierent source when used for Zone 2.
Output 1 allows audio from the TV to be received by the CXR. See later
TV-ARC section for details.
14. USB
BT100 – The optional Cambridge Audio BT100 Bluetooth adaptor should be
plugged in here adding wireless streaming bluetooth (A2DP/AVRCP) audio
capability directly from most phones, tablets and laptops. See later section
for details.
Wireless antenna – Allows connection to 802.11b/g or n networks (2.4 GHz
will only be used for n networks).
15. Speaker terminals
Connect to loudspeakers with a nominal impedance of 6-8 ohms. 7.1, 5.1 or
less connections can be made.
16. IR Receiver In
Allows modulated IR commands from IR repeater systems to be received
by the CXR.
17. Emitter in
Allows modulated IR commands from multi-room systems or IR repeater
systems to be received by the CXR.
18. IR out
Use with IR emitters to control the sources remotely. See later section.
19. Trigger out
12V triggers for controlling external ampliers, curtains, motorised screens or
other such equipment. See later section.
20. AC power socket
Once you have completed all connections to the amplier, plug the AC power
cable into an appropriate mains socket then switch on. Your CXR is now
ready for use.
21. RS232C
Used for control of the CXR in custom install situations. A full protocol is
available for the CXR on our website.
22. Power on/o
Switches the unit on and o.
9
CXR120/200
13. Surround modes
Selects digital surround processing modes and various
matrix encoded surround processing modes for
analogue or digital sources (digitally processed).
14. Stop/Play/Pause (StreamMagic)
Press to stop, play or pause streaming playback.
15. Direct
Disables any audio processing on the current source.
16. Dim
Adjust the backlight of the front panel display; o, dim
or bright.
17. Bass/Treble
Press for bass/treble/sub adjustment, using the
navigation ▲/▼ buttons. Note: Bass/Treble is
bypassed in analogue stereo direct and 7.1 direct
modes.
18. Lip sync
Press to activate and adjust the lip sync delay function
if the audio and video appear out of sync. While the Lip
sync delay status is shown on the unit's display, use
the navigation ▲/▼ buttons to adjust the delay time.
Adjusting the value to zero causes lip sync delay to be
turned o. See later section in this manual.
19. Store presets
Press to store the current frequency as a preset when
in Tuner mode.
20. Stereo/Mono
When listening to FM, press to alternate between
stereo and mono modes.
21. Presets
Press to recall stored presets.
22. Trigger
Toggle On and O the Trigger outputs. See trigger
section for details and setup.
23. Zone 2
Use to control Zone 2. Press and hold then press
Source buttons, Volume or Mute.
Main remote control
The CXR is supplied with a CX remote control. Insert
the supplied AAA batteries to use. For full details of the
various adjustment functions available from the remote,
refer to the later sections of this manual.
1. Backlight button
Press to turn the backlight on and illuminate the remote
control buttons.
2. Standby/On
Switches the unit between Standby mode and On.
3. Source buttons
Press the corresponding button to change the input
source. Pressing the tuner FM/AM button a second
time toggles between FM and AM modes.
Pressing the TV button selects TV-ARC (Audio Return
Channel).
Pressing the SM button selects the StreamMagic
module. The last used source in the module will be
selected which may be the optional BT100 or one
of the other sources controlled by the Cambridge
Connect app.
The above button descriptions are naturally brief.
Please refer to the 'Operating Instructions' section
of this manual for more information on the relevant
functions implemented.
4. Volume
Increase or decrease the volume of the AV receiver
output.
5. Back
Press to return to the previous menu.
6. Home
Press to turn on and o the on-screen setup menus for
display on your monitor/screen.
7. Skip
Use to skip between tracks played back on the
StreamMagic module.
8. Enter
Used in the OSD setup menus.
9. Navigation
Press to navigate around the menus. Also used for
character entry. ◄/► to move between character
entry, ▲/▼ to browse through the characters.
10. Mute
Mutes the audio on the AV Receiver. Press again to
cancel mute.
11. Info
Press to view the current source material and decoding
mode.
12. Stereo modes
Selects Stereo or Stereo + Sub modes for Analogue or Digital sources
(digitally processed).
Sources
1 2 3
5 6 7
4
8
Stereo
Modes
Stereo
Mono
Surround
Modes
Direct
Store
Presets
Zone 2
Bass
Treble
Lip
Sync
5 6 7 8
1 2 3 4
1
2
3
Blu-ray Trigger
Presets
CXR200
StreamMagic
TVSM MP3 FM/AM
Vol
Vol
Sources
1 2 3
5 6 7
4
8
Stereo
Modes
Stereo
Mono
Surround
Modes
Direct
Store
Presets
Zone 2
Bass
Treble
Lip
Sync
5 6 7 8
1 2 3 4
1
2
3
Trigger
Presets
CXR200
StreamMagic
TVSM MP3 FM/AM
Vol
Vol
1
3
5
8
7
10
12
13
15
17
19
23
2
4
4
6
7
9
11
21
22
14
16
18
20
10
To avoid damaging the speakers with a sudden high-level signal, be sure to
switch the power o before connecting the speakers. Check the impedance
of your speakers. Speakers with an impedance of 8 ohms (each) are
recommended.
The coloured speaker terminals are positive (+) and the black speaker
terminals are negative (-). Make sure correct polarity is maintained at each
speaker connector or the sound can become weak and "phasey" with little
bass.
Prepare the speaker cords for connection by stripping o approximately
10mm (3/8") or less (no more than 10mm, as this could cause a short-circuit)
of the outer insulation. Twist the wire tightly together so there are no loose
ends. Unscrew the speaker terminal knob, insert the speaker cable, tighten
the knob and secure the cable.
Note: All connections are made via loudspeaker cable, except if using an
active subwoofer which would be connected via a standard RCA phono
cable.
Loudspeaker connections
Banana Plugs (4mm standard) connected to the speaker cable are
recommended for direct insertion into the speaker terminals.
Please refer to the 'Speaker Conguration' section of this manual for more
information on 5.1 and 7.1 speaker setups.
Note: If necessary, it is possible to bi-amp the Front Left and Front Right
speakers resulting in more dynamic, higher-quality sound.
Surround back/height, Bi-amp and Zone 2 speaker connections can all be
wired to speakers, but only one set will be active. This can be set in the
Speaker Conguration menu.
www.cambridgeaudio.com
CXR200 AV Receiver
Designed & Engineered in Britain
Assembled in Vietnam
Surround Back/Height
Speaker Impedance: Nominal 8 Ohms
Right Left Front
Right
Front
Left
Centre Surround
Right
Surround
Left
SW1
7.1 5.1
Sub Out
SW1
Surround
speakers
Surround back
speakers
Centre
speaker
Front
speakers
Powered subwoofer
Phono/RCA
cable
11
CXR120/200
Pre Out
Sub Out
www.cambridgeaudio.com
CXR200 AV Receiver
Designed & Engineered in Britain
Assembled in Vietnam
Analogue audio connections
Note: Do not plug in the mains power lead or turn the unit on until all
connections have been made.
Connect to source equipment using stereo phono cables (stereo 2RCA-
2RCA). Tape/MD/CDR recorder/players require two sets of stereo phono/
RCA cables, one for recording, one for listening.
Digital audio connections
Two types of digital audio connections can be made to the CXR:
1. Optical (Toslink)
2. Coaxial (S/P DIF)
Note: Only one connection type should be used per source.
www.cambridgeaudio.com
CXR200 AV Receiver
Designed & Engineered in Britain
Assembled in Vietnam
Pre Out
Sub Out
Audio player/recorder
(Tape/MD/CD-R)
CD player Out
In
Phono cable
(2RCA-2RCA)
BD/DVD player
Out
BD/DVD player CD player
Audio player/recorder
(Tape/MD/CD-R)
iD100 Digital iPod Dock
Out
Out
OR
21
OR
12
OR
1
2
21
OR
Out Out
12
The CXR supports 4K (3840 x 2160 pixels) video resolution HDMI (input
and output) connections. 4K has twice the horizontal and vertical resolution
of the 1080p HDTV format, with four times as many pixels overall.
Use a High Speed HDMI cable when connecting 4K devices.
HDMI connections 4K video resolution
The CXR120 has 7 HDMI inputs (one of which is on the front) and two HDMI
outputs. The CXR200 has 8 HDMI inputs (one of which is on the front) and
two outputs. HDMI is a fully digital audio/video system for picture and audio
in digital format for best possible picture quality.
HDMI outputs on Blu-ray, DVD players and Set-top boxes also often support
higher resolution formats including progressive scan types. Consult both your
HDMI source and TV manuals for details, it is often possible to select from
various options, you will want to select the highest quality output that both
your source and TV are compatible with.
From Blu-ray players, HDMI can also carry the latest Dolby Digital Plus and
True-HD formats as well as DTS-HD High Resolution and Master Audio.
Ensure that the HDMI output of your player has been set to 'Bitstream'
or 'Raw' to pass the formats to the CXR for decoding. Also some Blu-ray
players feature settings to allow down conversion of Dolby Digital Plus etc.
to backwards compatible Dolby Digital 5.1 for older AV receivers which do
not support these formats. Ensure any such settings are disabled to allow our
CXR access to all the latest formats. For all the above reasons HDMI is the
preferred connection method for both Audio and Video.
HDMI (High-Denition Multi-Media Interface) is an all digital connection that
can carry both audio and video in one cable. Direct digital transfer of audio
and video and support for various types of High Denition video content and
high resolution audio make this the best connection type to use.
Pre Out
Sub Out
www.cambridgeaudio.com
CXR200 AV Receiver
Designed & Engineered in Britain
Assembled in Vietnam
HDMI cable
HDMI
cable
Blu-ray player with HDMI output
Set-top box with HDMI
output
4K
(3840 x 2160)
1080p
(1920 × 1080)
Note: 4K is not supported on the HDMI/MHL inputs.
13
CXR120/200
5.1/7.1 direct in
Pre Out
Sub Out
www.cambridgeaudio.com
CXR200 AV Receiver
Designed & Engineered in Britain
Assembled in Vietnam
DVD-A player or SACD multi-channel player 5.1
connections
Phono cables
(2RCA-2RCA)
Front Left
Surround Left
Front Right
Surround Right
Centre
Subwoofer
It can be desirable to connect DVD-A/SACD players to the CXR by two
methods at the same time.
A Digital or HDMI input can be made to the CXR for surround sound decoding
and an analogue connection to 7.1 Direct for DVD-A/SACD playback.
In the CXR Input Setup menu you can set the Audio Input connection to be
used with an HDMI Video Input.
If the Audio Input is selected to be the HDMI input then the CXR will decode
any relevant surround sound soundtracks.
If the Audio Input is selected to be '7.1ch direct in' then these pure analogue
connections will be used for the best sound quality and no DSP processing
or Bass and Treble adjustment in the CXR is possible.
DVD-A or SACD players can be connected to the CXR via its 5.1/7.1 Direct
inputs allowing multi-channel music playback from these sources.
DVD-A and SACD both support 5.1 output. The CXR's direct inputs also
allow optional connection of Surround Back signals for compatibility with 7.1
sources or external decoders.
HDMI connections cont.
Connection to the TV is by HDMI. Both outputs support 4K.
CXR200: Two outputs are tted that can be used individually or at the same
time (for a TV and projector perhaps).
HDMI 1 also supports Audio Return Channel (ARC) from TVs that also support
this feature. This allows audio from the TV to be received by the CXR. See
TV-ARC section of this manual. For CXR200, the HDMI 2 can be used for
Zone 2. See Zone 2 setup section of this manual.
CXR120: Both outputs always show the same video.
Pre Out
Sub Out
www.cambridgeaudio.com
CXR200 AV Receiver
Designed & Engineered in Britain
Assembled in Vietnam
HDMI cable
TV 2
ARC supported if TV
also supports.
TV 1
14
Pre out connections
Rec out connections
The Pre out Left and Right sockets provide an analogue pre out of the Front
Left and Front Right channels for attaching a separate power amplier to
these two channels. The subwoofer outputs are used for attaching a powered
subwoofer if needed.
The Rec out Left and Right sockets provide a direct Left and Right output
from a stereo input, or a downmix stereo analogue output from a multi-
channel input.
Pre Out
Sub Out
www.cambridgeaudio.com
CXR200 AV Receiver
Designed & Engineered in Britain
Assembled in Vietnam
Phono cables
(2RCA-2RCA)
Audio player/recorder
(Tape/MD/CD-R)
Pre Out
Sub Out
www.cambridgeaudio.com
CXR200 AV Receiver
Designed & Engineered in Britain
Assembled in Vietnam
Pre Out
Sub Out
Phono cables
(2RCA-2RCA)
Power
amplier
Powered subwoofer
15
CXR120/200
Front input connections
The front panel inputs are temporary connections, such as connections to
video games consoles, USB stick/hard-drives (via Cambridge Connect app)
etc. Alternatively, use the 3.5mm mini-jack MP3 socket for the headphone/
line outputs of portable MP3 players.
CX R200
HDMI 8/
S8
HDMI 8/
S8
Video games console/
Video camera outputs
HDMI/MHL cable
3.5mm mini-jack
USB cable
MP3
Player
USB hard
drive
Note: The MP3 input is also used for 'Auto setup' using the supplied auto
setup microphone. Refer to the 'Auto setup' section of this manual for more
information.
Aerial connections
FM aerial
Connect an aerial to the FM 75 ohm socket (a simple wire aerial is supplied
only for temporary use). Extend the lead and move the aerial around until you
get the best reception. For continued use, we strongly recommended using
a 75ohm outdoor FM aerial.
AM loop aerial
Connect each end of the single length antenna to the antenna terminals.
Place the antenna as far from the main system as possible to prevent
unwanted noise and to obtain optimum reception. If the AM loop aerial
provided does not receive sucient reception, it may be necessary to use
an outdoor AM aerial.
Pre Out
Sub Out
FM aerial
FM external
aerial
AM external
aerial
AM loop
aerial
OR
OR
Ground
(optional)
Examples
Examples
Note: Change the tuning mode via 'Input Setup > Mode' when the FM or AM
Tuner is selected as the source. In Preset mode the unit cycles through the
presets only. In Manual tuning mode the user can step manually through the
frequencies. In Scan tuning mode the unit scans to the next strong station.
1. Select either FM or AM tuner via the source button on the front panel or
remote control.
2. Press the Tuning +/- button on the front panel (or the ▲ and ▼ arrow
buttons on the remote) to select the station you want to listen to.
If necessary, the frequency increments for manual tuning can be altered for
AM and FM depending on geographic location. Navigate to 'General Settings
> AM/FM Tuner Steps'.
Two FM modes are available, Stereo and Mono - Press the Stereo/Mono
button on the remote to toggle between Stereo and Mono mode.
Radio Data Systems (RDS)
RDS is a method for the transmission of additional information from local
radio stations. It is only available in FM mode. RDS will only work if the
local broadcasting stations have RDS transmission and the signal is strong
enough.
Press the Info button on the remote and go through the displayed functions.
There are functions for PS, PTY and RT:
PS (Station Name) – current station name will be shown
PTY (Program Type) – current name type of the program will be shown
RT (Radiotext) – Radiotext messages will be shown, if available.
Note: If no valid RDS data has been received the Info button will display the
normal unit information.
Presets
Presets can be set for AM/FM Tuner.
Storing stations for Tuner
1. Tune in a station you wish to store as explained previously.
2. Press and hold the Store Presets button on the remote for 5 seconds. The
next available preset will be displayed.
3. Use the Tuning +/- on the front panel or the navigational buttons to select
a preset station number (1-30). The station number will be displayed on
the screen.
4. Press the Store Presets button on the remote to store the frequency.
StreamMagic
On the Connect App you can search for an Internet Radio station and then
add it to a Preset memory location in the app.
Preset stations can then be easily recalled on the Radio section of the
Connect App. The rst eight preset stations can also be recalled quickly using
the IR Remote Control buttons when the CXR is set to the Connect source.
For more information regarding Internet Radio, see StreamMagic section of
this manual.
Using the tuner
16
Operating instructions
To activate the CXR, switch the Power switch on the rear panel to On then
press the Standby/On button on the front panel.
Selecting the source
Select the source by using the Source +/- buttons on the front panel. After
4 to 5 seconds the CXR will select the new source, or it can be selected
by pressing the volume knob. The source selection buttons on the remote
control can also be used to directly select the source.
Selecting the desired listening mode
Select an appropriate mode for the source material/type you are listening to
by pressing the Stereo or Surround Modes button on the remote and cycling
through sub-modes where available.
In all cases the rst time a mode button is pressed the CXR will report the
current decoding mode on the front panel display. Pressing the button
again will then cycle to the next available mode (if there is one). If no button
is pressed for 4 or 5 seconds the CXR returns to normal operation without
changing mode.
Stereo Modes – Selects 2 channel Stereo operation for stereo material,
pressing again selects Stereo + Sub mode.
This is a digitally processed mode that allows bass and treble controls, and
sub generation if required. The input can be either analogue (in which case it
will be turned into digital by 24 bit A/D conversion) or natively digital.
Surround Modes – Selects a range of digital surround modes for the
appropriately digitally encoded material
Note: Some Surround Sound types (such as Dolby TrueHD and DTS HD) are
available only from Blu-ray disc over HDMI.
In some circumstances (see tables) pressing the button again will switch to
an alternative decoding option.
Dolby Pro Logic and DTS Neo:6 are both available in various guises to decode
appropriately encoded soundtracks. Additionally DSP modes are available to
process sources with no encoding at all. Due to the matrix encoding process
none of these modes incorporate ags that tell the CXR the type of encoding
used in the source material. Thus you must manually select these modes.
Pressing the Surround Modes button when the CXR has locked to a Dolby
Digital/DTS bitstream will present more options where possible including
Post-Processed modes.
These are modes that allow extra processing to be applied after the main
surround-sound decoding. For instance Dolby Digital (2/0) + Dolby Pro Logic
II Music. Which adds a 5.1 Dolby Pro Logic decode to a Stereo Dolby Digital
decode to turn 2 channel stereo into 5.1.
For 7.1 Speaker setups, the number of decoding possibilities increases as
shown in the following 'Decode modes' tables. Several extra Post Processing
modes are available using either Dolby Pro Logic IIx or DTS Neo:6.
Incoming Dolby Digital/DTS streams are always shown on the front panel
display as Dolby Digital (x/x).x or DTS (x/x).x, where the bracketed numbers
indicate the active channels in the source material. Active output channels
are shown by the icons on the right hand side of the front panel display.
Possible incoming Dolby Digital/DTS types are:
(1/0) – Mono, Centre channel only
(2/0) – Left/Right stereo
(2/0).1 – Left/Right stereo and LFE (Sub)
(2/2) – Left/Right stereo and Left/Right surround
(3/0) – Left, Centre, Right
(3/0).1 – Left, Centre, Right and LFE (Sub)
(3/2).1 – 5.1: Left, Right, Centre, Left Surround, Right Surround and LFE
(Sub)
(3/4).1 – 7.1: Left, Right, Centre, Left Surround, Right Surround, Surround
Back Left, Surround Back Right and LFE (Sub)
17
CXR120/200
Decode modes - 5.1 speaker setup
Incoming Native Modes available Output
audio channel channels
format resolution
PCM 2 PCM + All channels >5.1 MCS
PCM 2 "
PCM + Dolby Pro Logic II Movie >5.1
PCM + Dolby Pro Logic II Music >5.1
PCM + Neo:6 Cinema >5.1
PCM + Neo:6 Music >5.1
Dolby Digital (2/0) 2 Dolby Digital (2/0) + All channels >5.1 MCS
Dolby Digital (2/0) 2 "
Dolby Digital (2/0) + Dolby Pro Logic II Movie >5.1
Dolby Digital (2/0) + Dolby Pro Logic II Music >5.1
Dolby Digital (2/0) + Neo:6 Cinema >5.1
Dolby Digital (2/0) + Neo:6 Music >5.1
Dolby Digital 5.1 Dolby Digital (3/2).1 5.1
Dolby Digital EX 6.1 Dolby Digital EX (3/3).1 5.1<
DTS (2/0) 2 DTS (2/0) + All channels >5.1 MCS
DTS (2/0) 2 "
DTS (2/0) + Dolby Pro Logic II Movie >5.1
DTS (2/0) + Dolby Pro Logic II Music >5.1
DTS (2/0) + Neo:6 Cinema >5.1
DTS (2/0) + Neo:6 Music >5.1
DTS 5.1 DTS (3/2).1 5.1
DTS ES Matrix 6.1 DTS ES Matrix (3/3).1 5.1<
DTS ES Discrete 6.1 DTS ES Discrete (3/3).1 5.1<
DTS 96/24 5.1 DTS 96/24 5.1
Multi Channel PCM 5.1 $ Multi PCM (3/2).1 5.1
Multi Channel PCM 7.1 $ Multi PCM (3/4).1 5.1<
Dolby Digital Plus 5.1 $ Dolby Digital Plus (3/2).1 5.1
Dolby Digital Plus 7.1 $ Dolby Digital Plus (3/4).1 5.1<
Dolby True HD 5.1 $ Dolby True HD (3/2).1 5.1 &
Dolby True HD 7.1 $ Dolby True HD (3/4).1 5.1< &
DTS HD High Resolution 5.1 $ DTS-HD HR (3/2).1 5.1
DTS HD High Resolution 7.1 $ DTS-HD HR (3/4).1 5.1<
DTS Master Audio 5.1 $ DTS-HD MA (3/2).1 5.1 &
DTS Master Audio 7.1 $ DTS-HD MA (3/4).1 5.1< &
Dolby Digital/DTS Height 5.1 + H (7.1) Dolby Digital/DTS 5.1<H
Note: 5.1< H indicates a 5.1 decode of incoming height encoded formats.
Press the Surround Modes button on
the remote control.
Operating instructions cont.
18
Decode modes - 5.1 + Height speaker setup
Press the Surround Modes button on
the remote control.
Incoming Native Modes available Output
audio channel channels
format resolution
PCM 2 PCM 2 "
PCM + All Channels >5.1 MCS
PCM + Dolby Pro Logic IIz Height >5.1 + H
Dolby Digital (2/0) 2 Dolby Digital (2/0) 2
"
Dolby Digital (2/0) + All Channels >5.1 MCS
Dolby Digital (2/0) + Dolby Pro Logic IIz Height >5.1 + H
Dolby Digital 5.1 Dolby Digital (3/2).1 5.1
Dolby Digital (3/2).1 + Dolby Pro Logic IIz Height >5.1 + H<
Dolby Digital EX 6.1 Dolby Digital EX (3/3).1 5.1<
Dolby Digital EX (3/3).1 + Dolby Pro Logic IIz Height >5.1 + H<
DTS (2/0) 2 DTS (2/0) 2 "
DTS (2/0) + All Channels >5.1 MCS
DTS (2/0) + Dolby Pro Logic IIz Height >5.1 + H
DTS 5.1 DTS (3/2).1 5.1
DTS (3/2).1 + Dolby Pro Logic IIz Height >5.1 + H<
DTS ES Matrix 6.1 DTS ES Matrix (3/3).1 5.1<
DTS ES Matrix (3/3).1 Dolby Pro Logic IIz Height >5.1 + H<
DTS ES Discrete 6.1 DTS ES Discrete (3/3).1 5.1<
DTS ES Discrete (3/3).1 + Dolby Pro Logic IIz Height >5.1 + H<
DTS 96/24 5.1 DTS 96/24 5.1
DTS 96/24 + Dolby Pro Logic IIz Height >5.1 + H<
Multi Channel PCM 5.1 $ Multi PCM (3/2).1 5.1
Multi PCM (3/2).1 + Dolby Pro Logic IIz Height >5.1 + H<
Multi Channel PCM 7.1 $ Multi PCM (3/4).1 5.1<
Multi PCM (3/4).1 + Dolby Pro Logic IIz Height >5.1 + H<
Dolby Digital Plus 5.1 $ Dolby Digital Plus (3/2).1 5.1
Dolby Digital Plus (3/2).1 + Dolby Pro Logic IIz Height >5.1 + H<
Dolby Digital Plus 7.1 $ Dolby Digital Plus (3/4).1 5.1<
Dolby Digital Plus (3/4).1 + Dolby Pro Logic IIz Height >5.1 + H<
Dolby True HD 5.1 $ Dolby True HD (3/2).1 5.1 &
Dolby True HD (3/2).1 + Dolby Pro Logic IIz Height >5.1 + H<
Dolby True HD 7.1 $ Dolby True HD (3/4).1 5.1< &
Dolby True HD (3/4).1 + Dolby Pro Logic IIz Height >5.1 + H<
DTS HD High Resolution 5.1 $ DTS-HD HR (3/2).1 5.1
DTS-HD HR (3/2).1 + Dolby Pro Logic IIz Height >5.1 + H<
DTS HD High Resolution 7.1 $ DTS-HD HR (3/4).1 5.1<
DTS-HD HR (3/4).1 + Dolby Pro Logic IIz Height >5.1 + H<
DTS Master Audio 5.1 $ DTS-HD MA (3/2).1 5.1 &
DTS-HD MA (3/2).1 + Dolby Pro Logic IIz Height >5.1 + H<
DTS Master Audio 7.1 $ DTS-HD MA (3/4).1 5.1< &
DTS-HD MA (3/4).1 + Dolby Pro Logic IIz Height >5.1 + H<
Dolby Digital/DTS Height 5.1 + H (7.1) Dolby Digital/DTS 5.1 + H
Note: Native Dolby Digital/DTS height encoded material will be presented as
5.1 + H without Dolby Pro Logic IIz post processing being enabled.
19
CXR120/200
Incoming Native Modes available Output
audio channel channels
format resolution
PCM 2 PCM 2 "
PCM + All channels >7.1 MCS
PCM + Dolby Pro Logic IIx Movie >7.1
PCM + Dolby Pro Logic IIx Music >7.1
PCM + Neo:6 Cinema >7.1
PCM + Neo:6 Music >7.1
Dolby Digital (2/0) 2 Dolby Digital (2/0) 2 "
Dolby Digital (2/0) + All channels >7.1 MCS
Dolby Digital (2/0) + Dolby Pro Logic IIx Movie >7.1
Dolby Digital (2/0) + Dolby Pro Logic IIx Music >7.1
Dolby Digital (2/0) + Neo:6 Cinema >7.1
Dolby Digital (2/0) + Neo:6 Music >7.1
Dolby Digital 5.1 Dolby Digital (3/2).1 5.1
Dolby Digital (3/2).1 + Dolby Pro Logic IIx Movie >7.1
Dolby Digital (3/2).1 + Dolby Pro Logic IIx Music >7.1
Dolby Digital EX 6.1 Dolby Digital EX (3/3).1
Dolby Digital (3/3).1 + Dolby Pro Logic IIx Movie >7.1
Dolby Digital (3/3).1 + Dolby Pro Logic IIx Music >7.1
DTS (2/0) 2 DTS (2/0) 2 "
DTS (2/0) + All Channels >7.1 MCS
DTS (2/0) + Dolby Pro Logic IIx Movie >7.1
DTS (2/0) + Dolby Pro Logic IIx Music >7.1
DTS (2/0) + Neo:6 Cinema >7.1 %
DTS (2/0) + Neo:6 Music >7.1 %
DTS 5.1 DTS (3/2).1
DTS (3/2).1 5.1
DTS (3/2).1 + Dolby Pro Logic IIx Movie >7.1 %
DTS (3/2).1 + Dolby Pro Logic IIx Music >7.1 %
DTS ES Matrix 6.1 DTS ES Matrix (3/3).1 >7.1 %
DTS ES Matrix (3/3).1 + Dolby Pro Logic IIx Movie >7.1
DTS ES Matrix (3/3).1 + Dolby Pro Logic IIx Music >7.1
DTS ES Discrete 6.1 DTS ES Discrete (3/3).1 >7.1 %
DTS ES Discrete (3/3) + Dolby Pro Logic IIx Movie >7.1
DTS ES Discrete (3/3) + Dolby Pro Logic IIx Music >7.1
DTS 96/24 5.1 DTS 96/24 5.1
DTS 96/24 (3/2).1 + Dolby Pro Logic IIx Movie >7.1
DTS 96/24 (3/2).1 + Dolby Pro Logic IIx Music >7.1
Multi Channel PCM 5.1 $ Multi PCM 3/2.1 5.1
Multi PCM (3/2).1 + Dolby Pro Logic IIx Movie >7.1
Multi PCM (3/2).1 + Dolby Pro Logic IIx Music >7.1
Multi Channel PCM 7.1 $ Multi PCM 3/4.1 7.1
Decode modes - 7.1 speaker setup
When the source has been
appropriately encoded Dolby
Pro Logic II gives 5 channel
Neo:6 6 channel and Dolby
Pro Logic IIx 7 channel matrix
encoding
Operating instructions cont.
Press the Surround Modes button on
the remote control.
20
Dolby Digital Plus 5.1 $ Dolby Digital Plus (3/2).1 5.1
Dolby Digital Plus (3/2).1 + Dolby Pro Logic IIx Movie >7.1
Dolby Digital Plus (3/2).1 + Dolby Pro Logic IIx Music >7.1
Dolby Digital Plus 7.1 $ Dolby Digital Plus (3/4).1 7.1
Dolby True HD 5.1 $ Dolby True HD (3/2).1 5.1
Dolby True HD (3/2).1
*
+ Dolby Pro Logic IIx Movie >7.1
Dolby True HD (3/2).1
*
+ Dolby Pro Logic IIx Music >7.1 &
Dolby True HD 7.1 $ Dolby True HD (3/4).1 7.1 &
DTS HD High Resolution 5.1$ DTS-HD HR (3/2).1 5.1 &
DTS-HD HR (3/2).1 + Dolby Pro Logic IIx Movie >7.1&
DTS-HD HR (3/2).1 + Dolby Pro Logic IIx Music >7.1&
DTS HD High Resolution 7.1$ DTS-HD HR (3/4).1 7.1
DTS HD Master Audio 5.1 $ DTS-HD MA (3/2).1 5.1 &
DTS-HD MA (3/2).1 + Dolby Pro Logic IIx Movie >7.1 &
DTS-HD MA (3/2).1 + Dolby Pro Logic IIx Music >7.1 &
DTS HD Master Audio 7.1 $ DTS-HD MA (3/4).1 7.1 &
* <=96kHz
Incoming Native Modes available Output
audio channel channels
format resolution
Decode modes - 7.1 speaker setup
Key (all tables)
5.1< Indicates a 5.1 decode of 6.1 or 7.1 material (phantom back centre).
>5.1 Indicates a 5.1 output created by a 2.0 decode post processed to 5.1.
>7.1 Indicates a 7.1 output created by a 2.0 or 5.1 decode, post-processed
to 7.1.
5.1< H Indicates a 5.1 decode of incoming height encoded formats.
% 7.1 post process of 6.1 material. Center back surround channel played
back via two mono rear surrounds. Acoustically this is actually a native
format presentation.
" Stereo or Stereo + Sub, Press Stereo Modes Button to change.
! Digital Signal Processing created modes for signals with no encoding.
$ Available via HDMI inputs only.
& Lossless encoded format.
In all cases, pressing the Stereo Modes button on the remote always
cycles round:
Stereo Modes Output channels
Stereo 2
Stereo + Sub 2.1
Either native Stereo or downmix of Dolby Digital/DTS 5.1/6.1/7.1 etc.
All channels, L and R output via all Left and Right channels plus a Centre
channel and subwoofer mix are created.
Press the Surround Modes button on
the remote control.
/
