Passage/Privacy
Long Plate Door Hardware
Installation Instructions
Updated June 2016
Skip to Step if your door has pre-drilled bore holes.
See “Door Prep Template”
For 2-3/8”
Backset:
For 2-3/4” Backset
Threaded Privacy Pin Hole
(Privacy Only)
Door - Outside
Grandeur Long Plate Drilling Template
(Scale 1 to 1[full size])
(1) Locate the hole locations for your long plate on this template.
(FAV = Fifth Ave., GVC = Grande Victorian, PAR = Parthenon,
WIN = Windsor)
(2) Place drilling template on your door, centering the 2 1/8”
cross-bore hole. Keep template parallel with door edge.
(3) Mark the hole locations for your long plate on the door.
(4) Drill holes using a 7/64” diameter drill bit. Then go to step E on
the installation instructions.
DOOR EDGE: 2-3/4” from center of cross bore
DOOR EDGE: 2-3/8” from center of cross bore
DOOR EDGE: 2-3/8” from center of cross bore
DOOR EDGE: 2-3/4” from center of cross bore
Refer to Drilling Template on opposite page
Door - Outside
Emergency Release Hole
(Privacy Only)
Door - Outside
Mounting Plate
Door - Outside
1
3
2
Push onto
mounting
plate
Rotate plate clockwise
to lock into holes
Emergency Release Hole
(Privacy Only)
Door - Outside
Screw in the
Privacy Pin
(Privacy Only)
Emergency Release Hole
(Privacy Only)
PK144 Rev3 06022016
For assistance call 1-844-372-6848 Monday through Friday, 7 am to 5 pm Mountain Time or visit www.GrandeurHardware.com/support
Grandeur Long Plate Drilling Template
(Scale 1 to 1[full size])
(1) Locate the hole locations for your long plate on this template.
(FAV = Fifth Ave., GVC = Grande Victorian, PAR = Parthenon,
WIN = Windsor)
(2) Place drilling template on your door, centering the 2 1/8”
cross-bore hole. Keep template parallel with door edge.
(3) Mark the hole locations for your long plate on the door.
(4) Drill holes using a 7/64” diameter drill bit. Then go to step E on
the installation instructions.
DOOR EDGE: 2-3/4” from center of cross bore
DOOR EDGE: 2-3/8” from center of cross bore
DOOR EDGE: 2-3/8” from center of cross bore
DOOR EDGE: 2-3/4” from center of cross bore
Outside
Inside
PK144 Rev.3 06022016
For assistance call 1-844-372-6848 Monday through Friday, 7 am to 5 pm Mountain Time or visit www.GrandeurHardware.com/support
Door Hardware
Installation Instructions
Deadbolt Tongue must
be EXTENDED during
installation.
A B
Face of Door
Edge
of
Door
Centerline
For 2-3/8” Backset
3-1/2”
2-3/8”
3-3/4”
2-3/4”
Cross Bore
Hole -
2-1/8”
Diameter
For 2-3/4” Backset
Door Thickness
Centerline
Edge Bore
Hole - 1”
Diameter
Faceplate
Mortise Area
C D
Deadbolt Latch
Updated July 2015
!
Edge Bore
Hole
Tailpiece must be
VERTICAL during
installation.
!
#4
#5A
#5B
E F
Outside Assembly (Part #’s 4, 5A & 5B )
Deadbolt
Adaptor Plate
(Part #
6)
2-3/8”
Machine Screws
(Part #
7)
Inside
of Door
#
10
5/8”
Machine Screws
(Part #
9)
G
#11
#13
#3
#12
Door
Stop
Door
Jamb
Page 1 – PK147 Rev.3 06022016
Single Cylinder Deadbolt
For thicker doors, please call customer service.
For assistance call 1-844-372-6848 Mon-Fri, 7 am—5pm MST
or visit
www.GrandeurHardware.com/support
Updated June 2016
Part Part
# Description
1 Latch
2 Latch Faceplate
3 Latch & Strike Wood Screws (4)
4 Cylinder Body
4A Tailpiece
5A Spin Ring
5B Outside Escutcheon
6 Deadbolt Adapter Plate
7 2-3/8” Machine Screws (2)
8 Thumbturn Assembly
9 5/8” Thumbturn Machine Screws (2)
10 Dust Box
11 Door Frame Reinforcer
12 3” Reinforcer Wood Screws (2)
13 Strike Plate
Single Cylinder Deadbolt Exploded Parts Drawing
Single Cylinder Deadbolt
TM
For
Assistance
Call:
1-800-522-7336
8 am - 5 pm, Monday - Friday, MST
Door Hardware
Installation Instructions
For thicker doors, please call customer service.
Page 2 – PK147 Rev.2 07212015
PK147 Rev.3 06022016
/
