1
RUNNING A PROGRAMME
Find more information in the separate Instructions for Use.
Sort laundry according to
care symbols
Do not tumble dry
Suitable for tumble drying –
at low temperatures
Suitable for tumble drying
Sort laundry by:
Material thickness: whenever there is greater load than the dryer can handle, separate
laundry according to weight (e.g. dry towels and thin underwear separately).
Type of material: cotton (linen); synthetic textiles (easy care).
Degree of drying: cupboard dry, iron dry etc.
Do not tumble dry: nylon stockings, delicate embroidery, fabrics with metallic decorations.
Preparing laundry
Check that all fastenings are closed and that pockets are empty.
Please ensure that there are no cigarette lighters in the laundry.
Turn laundry inside out.
Loading dryer
Place laundry loosely in the drum to achieve equal drying throughout.
Then close the door.
Selecting programme
Select the drying programme required by turning the programme selector knob (for
information, refer to programme table).
If you do not start the programme soon after having made your choice, the dryer will switch
off after a few minutes.
To switch the dryer on again turn the programme selector knob to “Off” (“0”) and afterwards
to the desired programme.
Selecting options
(if available)
Select the option required by pressing the corresponding button.
The indicator lamp above the relevant button lights up to confirm your selection.
A fast blinking lamp indicates a wrong selection is made (incompatible options).
Press the button again to cancel the option.
Starting dryer
The drying programme is started by pressing the “Start (Pause)” button.
The relevant indicator lamp lights up.
Changing programme selection: If the programme selected is changed during drying, the
dryer stops.
The “Start (Pause)” indicator lamp flashes.
To operate the new programme, press the “Start (Pause)” button again.
Interrupting programme: To interrupt a drying cycle, press the “Start (Pause)” button and
open the door.
Wait at least 5 minutes, to allow the laundry to cool down, before you unload the dryer.
For your safety the drying cycle stops automatically if you open the door.
To restart, after door opening, close the door and press the “Start (Pause)” button again.
Warning: Never stop a tumble dryer before the end of the drying cycle, unless all items are
quickly removed and spread out so that the heat is dissipated.
Programme end –
unloading dryer
The final part of a drying cycle occurs without heat (cool down cycle) to ensure that the items
reach a lower temperature to avoid wrinkling.
End: Take the laundry out of the dryer.
The drying process is complete.
Anticrease: If the laundry is not removed at the end of the drying cycle, an automatic anti-
crease cycle will operate for maximum 15 min (by choosing the option “Anticrease” this time
can be extended up to 12 hours).
The drum rotates to prevent the laundry from creasing.
After the end of the “Anticrease” the dryer will switch off after a short time, to save energy.
Switching dryer off
Set the programme selector knob to “Off” (“0”).
Cleaning the door filter after every cycle: open door, pull door filter up and out of machine and open it. Brush lint using a soft
brush or your fingertips. Close door filter and push firmly back into place.
Emptying water container: pull container out by the handle and empty. Replace the container when empty by pushing it
completely back into place.
Please note: Only use additives/plastic items specified as dryer safe, and thoroughly rinse items that have been treated with
stain remover in plenty of water before drying. Never dry rubber objects or objects stained with vegetable oils in the dryer.
The Manufacturer is not liable for any damage to laundry resulting from inadequate or incorrect fabric care instructions which
have been provided with the garment or article.
2
Overview of programmes Options
Approximate drying times
(in minutes)
Type of textile
Programmes / Drying levels
Fabrics
Gentle
Schonen
Additional
reverse
Pflege+
Anticrease
Knitter-
schutz
Dryness
adjustment
Trocken-
grad
Pause
Start
(Pause)
Key lock
Kinder-
sicherung
Reset
Löschen
Finish in
Fertig
in
Very
wet load Wet load
Cotton
Extratrocken Extra dry
Multi-layered, thick laundry such as: terry
towels, terry towelling bath robes.
Cotton or linen hot wash /
coloured laundry
Koch-/Bunt-
wäsche
Max. 8.0 kg
X X X X X X X X 260 170
Schranktrocken Cupboard dry
Terry towels, dry towels, bed linen,
underwear
X X X X X X X X 230 150
*
Standard cotton programme, suitable to dry
normal wet cotton laundry. Most efficient
programme in terms of energy consumption
for drying normal wet cotton laundry.
X X X X X X X X 210 130
Bügeltrocken Iron dry*
Laundry which requires ironing such as: bed
and table linen, dry towels, T-shirts, polo
shirts, work clothes.
X X X X X X X X 180 110
Synthetic
Extratrocken Extra dry
Laundry with thick, multi-layered areas such
as: bed and table linen, track suits, anoraks,
blankets.
Synthetic, mixed fibre or cotton
easy care (ironing not required)
laundry
Pflegeleicht
Max. 4.0 kg
X X X X X X X X 110 90
Schranktrocken Cupboard dry*
Laundry which does not require ironing
such as: shirts, blouses, T-shirts,
sportsware.
X X X X X X X X 90 80
Bügeltrocken Iron dry
Laundry which requires ironing such as:
trousers, dresses, skirts, shirts, blouses.
X X X X X X X X 70 60
Special programmes
Supersanft
Delicate plus
Low drying intensity for delicates and items
such as: trousers, dresses, shirts, blouses.
Laundry made from synthetic
fibres such as polyamide,
nylon, polyacrylic, etc.
2.5 kg
X X X X X X X X 100 70
Mix
Mixed load
T-shirts, blouses, towels, underwear,
sportswear.
Cotton – synthetic blend
3.0 kg
X X X X X X X X 170 130
Seide
Silk Blouses, shirts and T-shirts.
Textiles made of silk
2.5 kg
X X X X X X X X 90 70
SoftFinish
Wool finish Hats, sweaters, scarves, gloves.
Textiles made of wool
1.0 kg
– X X – X X X X 6 6
XXL
Down Sleeping bags, trousers, vests.
Laundry that contains downs
3.0 kg
– X X – X X X X 150 130
Airing
Laundry is aired, refreshed and loosen
up for 30 minutes without heating.
All textiles.
Lüften
– – – – X X X – – –
Drying
times
Completes drying All textiles.
Zeitprogramme
10’ – 180’
– X X – X X X X 10’ – 180’
*Test programmes according to EN61121.
Reference pro
g
ramme for the Ener
gy
Label. Respect the manufacturer's recommendations on the care labels of
y
our laundr
y
.
3
HOW TO PROCEED IF…
If your machine is not functioning correctly, please check the following points before calling the customer service
– also refer to relevant chapter in the Instructions for use.
Drying takes too long /
Laundry is not dry
enough
• Has the correct drying programme been selected?
• Has the cycle been interrupted (door opening, full water container)?
• Was the inserted laundry too wet (washing machine spin speed less
than 1000 rpm)?
• Is the door filter dirty (filter indicator light on)?
• Is the bottom filter dirty (for more information, refer to the Instructions
for use)?
• Is the room temperature too high?
• Is the “End” and “Anticrease” indicator lamp lighting up?
The drying cycle is complete and the laundry can be taken out.
• If the drying result does not meet your expectation, select a more dry
programme or use the dryness adjustment option (if available) to
optimize the drying result.
The dryer does not
operate
• Is the plug properly inserted into the mains electricity socket?
• Is there a power failure?
• Has the fuse blown?
• Is the door properly closed?
• Has a drying programme been selected?
• Has the “Start (Pause)” button been pressed shortly after a
programme is selected? (If not, the dryer will switch off.)
• Has the start delay option been selected?
• Is the dryer overloaded? Please remove a part of the load.
Door filter, water
container or bottom
filter indicator lamp on
• Is the door filter clean?
• Is the water container empty?
• Has the water container been inserted correctly?
• Is the bottom filter clean and inserted correctly?
Water droplets
underneath the dryer
• Has the bottom filter been inserted correctly?
• Have all lint on the bottom filter seal and the door seal been wiped
away?
• Has the water container been inserted correctly?
• If the direct drain connection is used, is it tight?
• Is the dryer leveled?
...you want to maintain or clean your dryer:
Clean the door filter at
the end of every cycle
• Brush lint using a soft brush or your fingertips.
• Close the filter.
• Push the filter back into place.
Empty the water
container at the end of
every drying cycle
• Pull the handle to remove the water container.
• Empty the water container.
• Replace the water container when empty by pushing it completely
back into place.
Clean the bottom filter
at the end of every
fifth cycle
• Clean the bottom filter under running water.
• Remove all fluffs from the seals.
• Clean the bottom filter housing (for further information see chapter
“Cleaning the Bottom Filter” in the Instructions for use).
•
See the Instruction for use for further information how to clean the
bottom filter.
4
FAILURE CODES
In case of a malfunction of the dryer, one the following failure codes could be displayed.
Depending on the model of your dryer, the failure can be displayed in letters or by different blinking lamps.
Failure
code
Lamps failure code
Check needed by customer before
Service call
F01
Please call the After-Sales-Service.
F02
Please call the After-Sales-Service.
F03
Please call the After-Sales-Service.
F04
Please call the After-Sales-Service.
F05
Turn OFF the dryer.
Unplug the dryer.
Assure that the ambient temperature is
between 5°C and 35°C.
Wait for 1 hour.
Plug the dryer again and restart the dryer.
If the failure occurs again, please call the
After-Sales-Service.
F06
F07
F10 – F24
Turn OFF the dryer.
Unplug the dryer.
Wait for 30 minutes.
Plug the dryer again and restart the dryer.
If the failure occurs again, please call the
After-Sales-Service.
Start lamp is blinking 2 times per second when it is pressed
Assure that the door is correctly closed and
bottom filter correctly positioned.
Bottom filter lamp is blinking or Door filter lamp is blinking
2 times per second when the Start button is pressed
Assure that the bottom filter is correctly
positioned.
5
CONSUMPTION DATA
Power consumption: in of
f
-mode 0.11 W / in left on-mode 0.11 W
Load
Capacity [kg]
Spin Speed
[rpm]
Humidity
[%]
Energy
Consumption
[kWh]**
Drying Time
[min]**
*
8 1000 60 1.45 201
4 1000 60 0.82 126
8 800 70 1.74 234
8 1400 50 1.23 167
Cotton iron dry
8 800 70 1.25 216
8 1000 60 1.06 185
8 1400 50 0.89 154
Synthetic cupboard dry 4 1000 60 0.47 93
*Reference programmes for Energy Label/Regulation 392/2012/EU
**The energy consumption and drying time may differ from the values above as they depend on the operation
conditions (voltage fluctuation, mixture of textiles, humidity of the textiles after spinning, load capacity).
Selecting any options will also change the consumption data.
A
ll denoted values according to EN 61121.
Türfilter
Wärme
t
auscherfilte
Wässer-
behälter
leeren
B
e
Progra
m
The drying
this knob.
The “Start
“Start (
P
The drying
this button.
The indicat
Door Fil
t
The indicat
filter needs
Clean the
d
drying cy
c
e
-
e
r
Bottom
F
This indica
t
filter needs
This indica
t
bottom filte
Please tak
e
correctly in
s
engaged.
Water c
o
The indicat
container n
The drying
Empty the
c
programm
e
Empty the
drying cy
c
“Remaini
Depending
default dryi
A
fter start
o
corrected
d
moisture o
f
The dryin
g
value whi
c
drying cy
c
The flashin
is running.
The remai
n
e
fore using th
e
Q
I
n
m
me selecto
programme is
s
(Pause)” indic
a
P
ause)” but
t
programme is
s
or lamp lights u
t
e
r
or lamp lights u
to be cleaned.
d
oor filter at t
h
c
le.
F
ilte
r
t
or lamp lights
u
to be cleaned.
t
or lamp is blin
k
r is not correctl
y
e
care that the
b
s
erted and the
h
o
ntaine
r
or lamp lights u
eeds to be em
p
cycle is autom
a
c
ontainer and r
e
e
.
water contain
e
c
le
ng time” dis
p
on the progra
m
ng time is displ
a
o
f cycle the tim
e
d
epending on th
f
the laundry.
g
time specifie
d
c
h will be upda
c
le.
g lines indicate
n
ing time will be
e
machine, ple
a
uick R
e
n
dicator
l
r knob
s
elected by turn
a
tor lamp flash
e
on
s
tarted by pres
s
p.
p when the do
o
h
e end of ever
y
u
p when the bot
k
ing, when the
y
positioned.
b
ottom filter is
h
andle is fully
p when the wa
t
p
tied.
a
tically interrupt
e
e
start the dryin
g
e
r after every
p
lay
m
me selected a
a
yed.
e
displayed is
e
volume, type
d
is a calculat
e
ted during the
that the calcul
a
updated.
6
a
se also read t
eferen
lamps a
n
n
ing
e
s.
s
ing
o
r
y
t
tom
t
er
ed.
g
and
e
d
a
tion
h
e instruction
s
ce Gui
n
d Opti
o
E
c
Th
e
fe
e
th
e
Th
pr
o
A
s
to
a
“E
c
ex
p
Th
e
co
n
pr
o
th
e
Th
m
o
th
e
Fo
en
e
tu
m
E
n
Th
e
Pl
e
O
v
Th
e
co
n
th
e
D
r
By
dr
y
A
ft
yo
u
th
e
Pr
e
or
Pr
e
or
Pr
e
le
v
E
c
s
for use caref
u
de
o
ns
c
o Monito
r
e
“Eco monito
e
dback about th
e
e
selected prog
r
i
s function will
n
o
gramme.
soon as you tu
a
ny humidity st
e
c
o monitor” la
m
p
ected energy
c
e
three indicato
n
sumption: the
l
o
gramme settin
g
e
less indicators
i
s depends on t
o
isture and opti
o
e
size of the loa
d
r
that reason, t
h
e
rgy consumpti
o
m
ble dryer dete
c
n
d
e
drying progra
m
e
ase unload the
v
erdry prote
c
e
indicator light
s
n
trolled progra
m
e
activated prot
e
y
ness level
selecting this
o
y
ness level of th
e
r the selection
u
can choose t
h
e
button.
e
ssing 1 time y
o
e
ssing 2 times
y
e
ssing 3 times
y
el.
c
oMonitor
ully!
r” gives you a
r
e energy cons
u
r
amme.
n
ot work for a ti
m
rn the program
m
e
ared program
m
mps will indicat
c
onsumption.
o
rs show the de
g
less energy yo
u
g
is forecasted
t
s
will light up.
t
he programme
,
o
ns selected, a
n
d
.
h
e forecasted d
e
on may adapt
w
c
ts the load siz
e
mme is finishe
d
e
drye
r
.
c
tion
s up when a hu
m
me is selecte
d
e
ction function.
o
ption you can
a
h
e laundry.
n
of the desired
h
e dryness leve
l
o
u select a mor
e
y
ou select a les
s
y
ou select agai
n
r
ough
u
mption of
m
e-based
m
e selector
m
e, the
e
the
g
ree of
u
r
t
o consume,
initial
n
d also on
e
gree of
w
hen the
e
.
d
.
midity-
d
, to indicate
a
djust the
programme
l
by pressing
e
dry level
s
dry level
n
normal dry
7
Reset
During the selection phase of the
programme, pressing this button will switch
off all settings of selected options.
During running drying cycle the pressing of
the button will stop the cycle and set the
dryer back in selection mode.
The button needs to be pressed for
3 seconds.
Key lock
For child protection reasons, this option can
be used to lock all functions of the user
interface.
To activate this option, the button needs to
be pressed for 3 seconds, until the “key”
symbol at the display appears.
To deactivate this option, press the button
until the “key” symbol disappears.
The key lock function is still active even when
the selector knob is turned to “off” position
or the door is opened.
The function has to be deactivated.
Dry time adjustment
Turn the programme selector knob to
“Drying Time” position.
Press the button “Drying time” to select the
duration of cycle in ten minutes steps up to
180 minutes.
Gentle
Selecting this option will reduce the drying
temperature.
This option cannot be selected when the
option “Rapid” is selected.
Anticrease
This option can be chosen to reduce
wrinkling, when the laundry is not unloaded
directly after end of the cycle.
The drum turns from time to time for
maximum 12 hours.
It can be interrupted at any time by switching
off the dryer.
This option deactivates the “Buzzer”
function, if it is activated.
Finish in
With this function you can postpone your
programme to complete at a later time: press
the button to select in how many hours the
programme shall be finished.
• Thus, it allows you to have your laundry
ready at a particular time and to profit
from more favourable energy rates during
the night, for example.
• The “Finish in” function can be selected
in full hour time segments (1 to 24 h).
When you press the button, the shortest
possible time will be displayed; keep on
pressing the button to loop through all the
available times.
To remove it again, set the index of the
programme selector knob to the “Off”
“(0)” position.
• When you have selected the desired
“Finish in” time, press “Start” – the
countdown will begin.
• During the countdown, you can still
modify the option setting (select or
deselect options).
• Sometimes the programme may finish
before the selected “Finish in” time has
expired (e.g. for small loads).
In this case, the dryer will tumble the
laundry regularly to keep it fresh, until the
selected “Finish in” time has expired.
During tumbling, the display will show an
animation.
The tumbling phase can be stopped at
any time either by pressing any button, by
rotating the programme selector or by
opening the door.
A
dditional reverse
With this option the drum will turn during the
drying cycle more often against the main
turning direction than in a normal cycle.
This will improve the evenness of laundry
drying.
4000 107 29915
(Subject to technical modifications)
/