1
MACHINE OPERATION
Additional information (including troubleshooting and service) can be found in the individual chapters of
the Instructions for use.
Sort laundry according to
care symbols
Do not tumble dry
Suitable for tumble drying –
at low temperatures
Suitable for tumble drying
Sort laundry by:
Material thickness: whenever there is greater load than the dryer can handle,
separate laundry according to weight (e.g. dry towels and thin underwear separately).
Type of material: cotton (linen); synthetic textiles (easy care).
Degree of drying: cupboard dry, iron dry etc.
Do not tumble dry: nylon stockings, delicate embroidery, fabrics with metallic
decorations, bulky items such as sleeping bags or pillows.
Preparing laundry
Check that all fastenings are closed and that pockets are empty.
Please ensure that there are no cigarette lighters in the laundry.
Turn laundry inside out.
Loading dryer
Place laundry loosely in the drum to achieve equal drying throughout.
Then close the door.
Selecting programme
Select the drying programme required by turning the programme selector knob (for
information, refer to programme table).
Selecting options
(if available)
Select the option required by pressing the corresponding button.
The indicator lamp above the relevant button lights up to confirm your selection.
A fast blinking lamp indicates a wrong selection is made (incompatible options).
Press the button again to cancel the option.
Starting dryer
The drying programme is started by pressing the “Start (Pause)” button.
The relevant indicator lamp lights up.
Changing programme selection: If the programme selected is changed during
drying, the dryer stops. The “Start (Pause)” indicator lamp flashes.
To operate the new programme, press the “Start (Pause)” button again.
Interrupting programme: To interrupt a drying cycle, press the “Start (Pause)”
button and open the door. Wait at least 5 minutes, to allow the laundry to cool down,
before you unload the dryer. For your safety the drying cycle stops automatically if
you open the door.To restart, after door opening, close the door and press the “Start
(Pause)” button again.
Warning: Never stop a tumble dryer before the end of the drying cycle, unless all
items are quickly removed and spread out so that the heat is dissipated.
Programme end –
unloading dryer
The final part of a drying cycle occurs without heat (cool down cycle) to ensure that
the items reach a lower temperature to avoid wrinkling.
Anticrease: If the laundry is not removed at the end of the drying cycle, an automatic
anti-crease cycle will operate for maximum 15 min (by choosing the option
“Anticrease” this time can be extended up to 12 hours).
The drum rotates to prevent the laundry from creasing.
End: Take the laundry out of the dryer.
The drying process is complete and the anti-crease phase has been reached (active).
Switching dryer off
Set the programme selector knob to “Off” (“O”).
Cleaning the lint filter after every cycle: open door, pull lint filter up and out of machine and open it. Brush lint using a soft
brush or your fingertips. Close door filter and push firmly back into place.
Emptying water container: pull container out by the handle and empty. Replace the container when empty by pushing it
completely back into place.
Please note: Only use additives/plastic items specified as dryer safe and rinse items that have been treated with stain remover
thoroughly in plenty of water before drying. Never dry rubber objects or objects stained with vegetable oils in the dryer.
The Manufacturer is not liable for any damage to laundry resulting from inadequate or incorrect fabric care instructions which
have been provided with the garment or article.
2
Overview of programmes Options
Approximate
drying times
(in minutes)
Type of textile
Programmes / Drying levels
Fabrics
Délicat
Gentle
Antifrois-
sage plus
Anticrease
Rapide
Rapid
Niveau de
sechage
Dryness
adjustment
Départ
(pause)
Pause
3”
Key lock
Annulation
Reset
Heure
de fin
Finish
in
Very wet
load
Wet
load
Cotton
W
Extra dry
Multi-layered, thick laundry such as: terry
towels, terry towelling bath robes.
Cotton or linen hot wash /
coloured laundry
Max. 9.0 kg
X X X X X X X X 210 180
Cupboard dry +
Terry towels, dry towels, bed linen,
underwear
X X X X X X X X 185 160
Cupboard dry*
Similar types of laundry which do not
require ironing such as: dry towels, bed
linen, underwear, baby clothes, T-shirts,
cotton socks.
X X X X X X X X 160 135
Iron dry*
Laundry which requires ironing such as: bed
and table linen, dry towels, T-shirts, polo
shirts, work clothes.
X X X X X X X X 130 110
Synthetic
VW
Extra dry
Laundry with thick, multi-layered areas such
as: bed and table linen, track suits, anoraks,
blankets.
Synthetic, mixed fibre or cotton easy care
(ironing not required) laundry
Max. 4.5 kg
X X – X X X X X 95 70
Cupboard dry*
Laundry which does not require ironing
such as: shirts, blouses, T-shirts,
sportsware.
X X – X X X X X 70 50
Iron dry
Laundry which requires ironing such as:
trousers, dresses, skirts, shirts, blouses.
X X – X X X X X 60 45
Special programmes
V
Delicate plus
Low drying intensity for delicates and items
such as: trousers, dresses, shirts, blouses.
Laundry made from synthetic fibres such as
polyamide, nylon, polyacrylic, etc.
2.5 kg
X X – – X X X X 85 70
Mixed load
T-shirts, blouses, towels, underwear,
sportswear.
Cotton – synthetic blend
3.0 kg
X X – X X X X X 80 60
Jeans Jeans, working trousers and jackets.
Cotton
3.0 kg
X X – X X X X X 105 85
Silk Blouses, shirts and T-shirts.
Textiles made of silk
2.5 kg
X X – – X X X X 85 70
Sport
Sport clothes, functional underwear, running
tights.
Synthetic
2.5 kg
X X – – X X X X 85 70
Airing
Laundry is aired, refreshed and loosen up for 30
minutes without heating.
All textiles.
– – – – X X X X 30’ –
Drying
items
Completes drying (suitable for all fabrics)
10’ 20’ 30’ 40’ 50’ 60’ 70’ 80’ 90’ 100’ 110’ 120’
X X X – X X X X
10’ 20’ 30’ 40’
50’ 60’ 70’ 80’
90’ 100’ 110’
120’
*Test programmes according to EN61121, tested with maximum rated load capacity.
3
HOW TO PROCEED IF…
...you want to check the dryer yourself first: (If your machine is not functioning correctly, please check the
following points before calling the customer service – also refer to relevant chapter in the Instructions for use)
Drying takes too long /
Laundry is not dry
enough
Has the correct drying programme been selected?
Has the cycle been interrupted (door opening, full water container)?
Was the inserted laundry too wet (washing machine spin speed less
than 1000 rpm)?
Is the lint filter dirty (filter indicator light on)?
Is the heat exchanger dirty (for more information, refer to the
Instructions for use)?
Is the room temperature too high?
Is the “End” and “Anticrease” indicator lamp lighting up?
The drying cycle is complete and the laundry can be taken out.
If the drying result does not meet your expectation, select a more dry
programme or use the dryness adjustment option (if available) to
optimize the drying result.
Is thin and thick load mixed? Are different types of materials mixed?
Sort the laundry after thickness and material and dry again.
The dryer does not
operate (after a power
failure, always press
the “Start (Pause)”
button)
Is the plug properly inserted into the mains electricity socket?
Is there a power failure?
Has the fuse blown?
Is the door properly closed?
Has a drying programme been selected?
Has the “Start (Pause)” button been pressed?
Has the start delay option been selected?
Is the dryer overloaded? Please remove a part of the load.
Filter, water container
indicator lamp on
Is the lint filter clean?
Is the water container empty?
Has the water container been inserted correctly?
Is the heat exchanger clean and inserted correctly?
Water droplets
underneath the dryer
Has the heat exchanger been inserted correctly?
Have all lint on the heat exchanger seal and the door seal been
wiped away?
Has the water container been inserted correctly?
If the direct drain connection is used, is it tight?
Is the dryer leveled?
...you want to care of and clean your dryer:
Clean the filter at the
end of every cycle
Brush lint using a soft brush or your fingertips.
Close the filter.
Push the filter back into place.
Empty the water
container at the end of
every drying cycle
Pull the handle to remove the water container.
Empty the water container.
Replace the water container when empty by pushing it completely
back into place.
Clean the heat
exchanger at least
once a month
Clean the heat exchanger under running water.
Remove all fluffs from the seals.
Clean the heat exchanger housing (for further information see
chapter “Cleaning the heat exchanger” in the Instructions for use).
4
FAILURE CODES
In case of a malfunction of the dryer, one the following failure codes could be displayed.
Depending on the model of your dryer, the failure can be displayed in letters or by different blinking lamps.
Failure
code
Lamps failure code
Check needed by customer before
Service call
F01
Please call the After-Sales-Service.
F02
Please call the After-Sales-Service.
F03
Please call the After-Sales-Service.
F04
Please call the After-Sales-Service.
F05
Turn OFF the dryer. Unplug the dryer.
Assure that the ambient temperature is
between 5°C and 35°C. Wait for 1 hour.
Plug the dryer again and restart the dryer.
If the failure occurs again, please call the
After-Sales-Service.
F06
F07
F10 – F22
Turn OFF the dryer. Unplug the dryer. Wait
for 30 minutes. Plug the dryer again and
restart the dryer. If the failure occurs again,
please call the After-Sales-Service.
Start lamp is blinking 2 times per second when it is pressed
Assure that the door is correctly closed and
heat exchanger correctly positioned.
Heat exchanger lamp is blinking 2 times when the Start
button is pressed
Assure that the heat exchanger is correctly
positioned.
B
e
A
Progra
m
The drying
this knob.
The “Start
“Start (
P
The drying
this button.
The indicat
Filter
The indicat
filter needs
Clean the
d
drying cy
c
Water c
o
The indicat
container n
The drying
Empty the
c
programm
e
Empty the
drying cy
c
Clean h
e
The LED li
g
heat excha
Clean the
h
“Remaini
Depending
default dryi
A
fter start
o
corrected
d
moisture o
f
The dryin
g
value whi
c
drying cy
c
The flashin
is running.
The remai
n
e
fore using th
e
A
ZB 96
8
I
n
m
me selecto
programme is
s
(Pause)” indic
a
P
ause)” but
t
programme is
s
or lamp lights u
or lamp lights u
to be cleaned.
d
oor filter at t
h
c
le.
o
ntaine
r
or lamp lights u
eeds to be em
p
cycle is autom
a
c
ontainer and r
e
e
.
water contain
e
c
le
e
at exchan
g
g
hts up after 30
nger needs to
b
h
eat exchanger
.
ng time” dis
p
on the progra
m
ng time is displ
a
o
f cycle the tim
e
d
epending on th
f
the laundry.
g
time specifie
d
c
h will be upda
c
le.
g lines indicate
n
ing time will be
e
machine, ple
a
8
3 – Q
u
n
dicator
r knob
s
elected by turn
a
tor lamp flash
e
on
s
tarted by pres
s
p.
p when the do
o
h
e end of ever
y
p when the wa
t
p
tied.
a
tically interrupt
e
e
start the dryin
g
e
r after every
g
e
r
cycles when th
b
e cleaned.
p
lay
m
me selected a
a
yed.
e
displayed is
e
volume, type
d
is a calculat
e
ted during the
that the calcul
a
updated.
5
a
se also read
t
u
ick R
e
lamps a
n
ing
e
s.
s
ing
o
r
y
t
er
ed.
g
h
e
and
e
d
a
tion
t
he instructio
n
e
feren
c
nd Opti
o
E
c
Th
e
fe
e
th
e
Th
pr
o
A
s
to
a
“E
c
ex
p
Th
e
co
n
pr
o
th
e
Th
m
o
th
e
Fo
en
e
tu
m
E
n
Th
e
Pl
e
O
v
Th
e
co
n
th
e
s for use care
f
c
e Gui
o
ns
c
o Monito
r
e
“Eco monito
e
dback about th
e
e
selected prog
r
i
s function will
n
o
gramme.
soon as you tu
a
ny humidity st
e
c
o monitor” la
m
p
ected energy
c
e
three indicato
n
sumption: the
l
o
gramme settin
g
e
less indicators
i
s depends on t
o
isture and opti
o
e
size of the loa
d
r
that reason, t
h
e
rgy consumpti
o
m
ble dryer dete
c
n
d
e
drying progra
m
e
ase unload the
v
erdry prote
c
e
indicator light
s
n
trolled progra
m
e
activated prot
e
f
ully!
de
r” gives you a
r
e energy cons
u
r
amme.
n
ot work for a ti
m
rn the program
m
e
ared program
m
mps will indicat
c
onsumption.
o
rs show the de
g
less energy yo
u
g
is forecasted
t
s
will light up.
t
he programme
,
o
ns selected, a
n
d
.
h
e forecasted d
e
on may adapt
w
c
ts the load siz
e
mme is finishe
d
e
drye
r
.
c
tion
/
6th Se
n
s up when a hu
m
me is selecte
d
e
ction function.
r
ough
u
mption of
m
e-based
m
e selector
m
e, the
e
the
g
ree of
u
r
t
o consume,
initial
n
d also on
e
gree of
w
hen the
e
.
d
.
n
se
midity
d
, to indicate
6
Dryness level
By selecting this option you can adjust the
dryness level of the laundry.
A
fter the selection of the desired programme
you can choose the dryness level by pressing
the button.
Pressing 1 time you select a more dry level
or
Pressing 2 times you select a less dry level
or
Pressing 3 times you select again normal dry
level
.
Reset
During the selection phase of the
programme, pressing this button will switch
off all settings of selected options.
During running drying cycle the pressing of
the button will stop the cycle and set the
dryer back in selection mode.
The button needs to be pressed for
3 seconds.
Key lock
For child protection reasons, this option can
be used to lock all functions of the user
interface.
To activate this option, the button needs to
be pressed for 3 seconds, until the “key”
symbol at the display appears.
To deactivate this option, press the button
until the “key” symbol disappears.
The key lock function is still active even when
the selector knob is turned to “off” position
or the door is opened.
The function has to be deactivated.
Dry time adjustment
Turn the programme selector knob to
“Drying Time” position.
Press the button “Drying time” to select the
duration of cycle in ten minutes steps up to
120 minutes.
Gentle
Selecting this option will reduce the drying
temperature.
This option cannot be selected when the
option “Rapid” is selected.
Rapid
Selecting this option reduces the drying time.
This option should only be selected for cotton
programmes, with a maximum load of 3.5 kg.
The garments shall have similar size and
thickness.
Anticrease
This option can be chosen to reduce
wrinkling, when the laundry is not unloaded
directly after end of the cycle.
The drum turns from time to time for
maximum 12 hours.
It can be interrupted at any time by switching
off the dryer.
This option deactivates the “Buzzer”
function, if it is activated.
Finish in
With this function you can postpone your
programme to complete at a later time: press
the button to select in how many hours the
programme shall be finished.
Thus, it allows you to have your laundry
ready at a particular time and to profit
from more favourable energy rates during
the night, for example.
The “Finish in” function can be selected
in full hour time segments (1 to 24 h).
When you press the button, the shortest
possible time will be displayed; keep on
pressing the button to loop through all the
available times.
To remove it again, set the index of the
programme selector knob to the “Off”
position.
When you have selected the desired
“Finish in” time, press “Start” – the
countdown will begin.
During the countdown, you can still
modify the option setting (select or
deselect options).
Sometimes the programme may finish
before the selected “Finish in” time has
expired (e.g. for small loads).
In this case, the dryer will tumble the
laundry regularly to keep it fresh, until the
selected “Finish in” time has expired.
During tumbling, the display will show an
animation.
The tumbling phase can be stopped at
any time either by pressing any button, by
rotating the programme selector or by
opening the door.
5019 307 01572
(Subject to technical modifications)
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Whirlpool Hampton User guide
-
-
-
-
Whirlpool AZB 8010 Program Chart
-
-
-
-
-
Whirlpool AZB 1059 Program Chart
Other documents
-
Bauknecht TK PLUS 73B BW Program Chart
-
-
Maytag MYU 935 CWT Program Chart
-
Bauknecht TRKK 72101 BK Program Chart
-
Bauknecht TR EXCELLENCE 7 Program Chart
-
-
LADEN AM 3998 LA Program Chart
-
-
-