Riello RLS 130 TC LP FS1 3/208-230/380/60 230/50-60 Installer Manual

Installation, use and maintenance instructions

20168481 (1) - 08/2019

Dual fuel light oil/ gas burner

Two stage operation

CODE MODEL

20169069 RLS 130

Translation of the original instructions

1 20168481

Contents

1 Declarations................................................................................................................................................................................ 3

2 Information and general warnings............................................................................................................................................ 4

2.1 Information about the instruction manual .................................................................................................................... 4

2.1.1 Introduction.................................................................................................................................................................. 4

2.1.2 General dangers.......................................................................................................................................................... 4

2.1.3 Other symbols ............................................................................................................................................................. 4

2.1.4 Delivery of the system and the instruction manual...................................................................................................... 5

2.2 Guarantee and responsibility....................................................................................................................................... 5

3 Safety and prevention................................................................................................................................................................ 6

3.1 Introduction.................................................................................................................................................................. 6

3.2 Personnel training ....................................................................................................................................................... 6

4 Technical description of the burner ......................................................................................................................................... 7

4.1 Burner designation ...................................................................................................................................................... 7

4.2 Models available.......................................................................................................................................................... 7

4.3 Burner categories - Countries of destination ............................................................................................................... 7

4.4 Technical data............................................................................................................................................................. 8

4.5 Electrical data.............................................................................................................................................................. 8

4.6 Maximum dimensions.................................................................................................................................................. 9

4.7 Burner equipment........................................................................................................................................................ 9

4.8 Firing rates ................................................................................................................................................................ 10

4.9 Test boiler.................................................................................................................................................................. 10

4.10 Burner description ..................................................................................................................................................... 11

4.11 Electrical panel description........................................................................................................................................ 12

4.12 Control box RFGO-A22............................................................................................................................................. 13

4.13 Servomotor (LKS 210 ...)........................................................................................................................................... 14

5 Installation ................................................................................................................................................................................ 15

5.1 Notes on safety for the installation ............................................................................................................................ 15

5.2 Handling .................................................................................................................................................................... 15

5.3 Preliminary checks .................................................................................................................................................... 15

5.4 Operating position ..................................................................................................................................................... 16

5.5 Preparing the boiler................................................................................................................................................... 16

5.5.1 Boring the boiler plate ............................................................................................................................................... 16

5.5.2 Blast tube length........................................................................................................................................................ 16

5.5.3 Securing the burner to the boiler............................................................................................................................... 16

5.6 Access to head internal part...................................................................................................................................... 17

5.6.1 Combustion head pre-calibration .............................................................................................................................. 17

5.7 Electrode positions.................................................................................................................................................... 17

5.8 Nozzle installation ..................................................................................................................................................... 18

5.8.1 Recommended nozzle............................................................................................................................................... 18

5.9 Combustion head adjustment.................................................................................................................................... 19

5.9.1 Adjustments prior to ignition (with light oil)................................................................................................................ 19

5.10 Light oil supply........................................................................................................................................................... 20

5.10.1 Loop circuit ................................................................................................................................................................ 20

5.10.2 Hydraulic connections ............................................................................................................................................... 21

5.10.3 Hydraulic circuit diagram ........................................................................................................................................... 21

5.11 Pump......................................................................................................................................................................... 22

5.11.1 Technical data........................................................................................................................................................... 22

5.11.2 Priming pump ............................................................................................................................................................ 22

5.12 Gas supply ................................................................................................................................................................ 23

5.12.1 Gas feeding line ........................................................................................................................................................ 23

5.12.2 Gas train.................................................................................................................................................................... 24

5.12.3 Gas train installation.................................................................................................................................................. 24

5.12.4 Gas pressure............................................................................................................................................................. 24

20168481 2

Contents

5.13 +Electrical connections ..............................................................................................................................................25

5.13.1 Supply cables and external connections passage .....................................................................................................25

5.14 Calibration of the thermal relay ..................................................................................................................................26

5.15 Motor rotation.............................................................................................................................................................26

6 Start-up, calibration and operation of the burner ..................................................................................................................27

6.1 Notes on safety for the first start-up...........................................................................................................................27

6.2 Adjustments prior to ignition (light oil) ........................................................................................................................27

6.2.1 1st and 2nd stage nozzles .........................................................................................................................................27

6.2.2 Combustion head.......................................................................................................................................................27

6.2.3 Pump pressure...........................................................................................................................................................27

6.2.4 1st stage fan damper .................................................................................................................................................27

6.2.5 2nd stage fan damper ................................................................................................................................................27

6.3 Burner ignition (light oil) .............................................................................................................................................27

6.4 Adjustments prior to ignition (gas) .............................................................................................................................28

6.5 Burner start-up (gas)..................................................................................................................................................28

6.6 Burner ignition............................................................................................................................................................28

6.7 Change of fuel............................................................................................................................................................29

6.8 Burner adjustment (gas) ............................................................................................................................................29

6.8.1 Output in 2nd stage....................................................................................................................................................29

6.8.2 Output in 1st stage.....................................................................................................................................................29

6.8.3 Ignition output (gas) ...................................................................................................................................................29

6.8.4 Operation with LPG - Propane - Butane ....................................................................................................................29

6.9 Servomotor adjustment..............................................................................................................................................30

6.10 Pressure switch adjustment .......................................................................................................................................31

6.10.1 Air pressure switch - check CO..................................................................................................................................31

6.10.2 Gas minimum pressure switch...................................................................................................................................31

6.11 Operation sequence of the burner .............................................................................................................................32

6.11.1 Burner start-up...........................................................................................................................................................32

6.11.2 Ignition failure.............................................................................................................................................................32

6.11.3 Burner flame goes out during operation.....................................................................................................................32

6.11.4 LED PANEL ...............................................................................................................................................................32

6.12 Final checks (with burner operating)..........................................................................................................................33

7 Maintenance ..............................................................................................................................................................................34

7.1 Notes on safety for the maintenance .........................................................................................................................34

7.2 Maintenance programme ...........................................................................................................................................34

7.2.1 Maintenance frequency..............................................................................................................................................34

7.2.2 Safety test - with no gas supply .................................................................................................................................34

7.2.3 Checking and cleaning...............................................................................................................................................34

7.2.4 Combustion control (gas)...........................................................................................................................................36

7.2.5 Safety components ....................................................................................................................................................36

7.3 Opening the burner ....................................................................................................................................................37

7.4 Closing the burner......................................................................................................................................................37

8 LED indicator and special function.........................................................................................................................................38

8.1 Description of LED lamps ..........................................................................................................................................38

8.2 Check mode function .................................................................................................................................................38

8.3 Flame control lock-out or emergency stop condition .................................................................................................38

8.4 LED lamps: burner operating status ..........................................................................................................................39

9 Problems - Causes - Remedies signalled by LED indicators ...............................................................................................40

A Appendix - Accessories ...........................................................................................................................................................45

B Appendix - Electrical panel layout...........................................................................................................................................46

3 20168481

Declarations

Declaration of Conformity in accordance with ISO / IEC 17050-1

These products are in compliance with the following Technical Standards:

• EN 12100

•EN 676

•EN 267

According to the European Directives:

MD 2006/42/EC Machine Directive

LVD 2014/35/EU Low Voltage Directive

EMC 2014/30/EU Electromagnetic Compatibility

The quality is guaranteed by a quality and management system certified in accordance with ISO 9001:2015.

1 Declarations

20168481 4

Information and general warnings

2.1 Information about the instruction manual

2.1.1 Introduction

The instruction manual supplied with the burner:

is an integral and essential part of the product and must not

be separated from it; it must therefore be kept carefully for

any necessary consultation and must accompany the burner

even if it is transferred to another owner or user, or to

another system. If the manual is lost or damaged, another

copy must be requested from the Technical Assistance

Centre of the area;

is designed for use by qualified personnel;

offers important indications and instructions relating to the

installation safety, start-up, use and maintenance of the

burner.

Symbols used in the manual

In some parts of the manual you will see triangular DANGER

signs. Pay great attention to these, as they indicate a situation of

potential danger.

2.1.2 General dangers

The dangers can be of 3 levels, as indicated below.

2.1.3 Other symbols

Abbreviations used

Ch. Chapter

Fig. Figure

Page Page

Sec. Section

Tab. Table

2 Information and general warnings

DANGER

Maximum danger level!

This symbol indicates operations which, if not

carried out correctly, cause serious injury, death

or long-term health risks.

ATTENTION

This symbol indicates operations which, if not

carried out correctly, may cause serious injury,

death or long-term health risks.

CAUTION

This symbol indicates operations which, if not

carried out correctly, may cause damage to the

machine and/or injury to people.

DANGER

DANGER: LIVE COMPONENTS

This symbol indicates operations which, if not

carried out correctly, lead to electric shocks with

lethal consequences.

DANGER: FLAMMABLE MATERIAL

This symbol indicates the presence of flammable

materials.

DANGER: BURNING

This symbol indicates the risks of burns due to

high temperatures.

DANGER: CRUSHING OF LIMBS

This symbol indicates the presence of moving

parts: danger of crushing of limbs.

WARNING: MOVING PARTS

This symbol indicates that you must keep limbs

away from moving mechanical parts; danger of

crushing.

DANGER: EXPLOSION

This symbol signals places where an explosive

atmosphere may be present. An explosive

atmosphere is defined as a mixture - under

atmospheric conditions - of air and flammable

substances in the form of gases, vapours, mist or

dust in which, after ignition has occurred,

combustion spreads to the entire unburned

mixture.

PERSONAL PROTECTION EQUIPMENT

These symbols indicate the equipment that must

be worn and kept by the operator for protection

against threats against safety and/or health while

at work.

OBLIGATION TO ASSEMBLE THE COVER

AND ALL THE SAFETY AND PROTECTION

DEVICES

This symbol signals the obligation to reassemble

the cover and all the safety and protection devices

of the burner after any maintenance, cleaning or

checking operations.

ENVIRONMENTAL PROTECTION

This symbol gives indications for the use of the

machine with respect for the environment.

IMPORTANT INFORMATION

This symbol indicates important information that

you must bear in mind.

This symbol indicates a list.

5 20168481

Information and general warnings

2.1.4 Delivery of the system and the instruction

manual

When the system is delivered, it is important that:

the instruction manual is delivered to the user by the system

manufacturer, with the recommendation to keep it in the

room where the heat generator is to be installed.

The instruction manual shows:

– the serial number of the burner;

– the address and telephone number of the nearest

Assistance Centre

The system supplier must carefully inform the user about:

– the use of the system;

– any further tests that may be required before activating the

system;

– maintenance, and the need to have the system checked at

least once a year by a representative of the manufacturer

or another specialised technician.

To ensure a periodic check, the manufacturer

recommends the drawing up of a Maintenance Contract.

2.2 Guarantee and responsibility

The manufacturer guarantees its new products from the date of

installation, in accordance with the regulations in force and/or the

sales contract. At the moment of the first start-up, check that the

burner is integral and complete.

In particular, the rights to the guarantee and the responsibility will

no longer be valid, in the event of damage to things or injury to

people, if such damage/injury was due to any of the following

causes:

incorrect installation, start-up, use and maintenance of the

burner;

improper, incorrect or unreasonable use of the burner;

intervention of unqualified personnel;

carrying out of unauthorised modifications on the equipment;

use of the burner with safety devices that are faulty,

incorrectly applied and/or not working;

installation of untested supplementary components on the

burner;

powering of the burner with unsuitable fuels;

faults in the fuel supply system;

continuation of use of the burner when a fault has occurred;

repairs and/or overhauls incorrectly carried out;

modification of the combustion chamber with inserts that

prevent the regular development of the structurally

established flame;

insufficient and inappropriate surveillance and care of those

burner components most likely to be subject to wear and

tear;

use of non-original components, including spare parts, kits,

accessories and optional;

force majeure.

The manufacturer furthermore declines any and every

responsibility for the failure to observe the contents of this

manual.

.........................................................................................

ATTENTION

Failure to observe the information given in this

manual, operating negligence, incorrect

installation and carrying out of non authorised

modifications will result in the annulment by the

manufacturer of the guarantee that it supplies with

the burner.

20168481 6

Safety and prevention

3.1 Introduction

The burners have been designed and built in compliance with

current regulations and directives, applying the known safety

technical rules and envisaging all the potential danger situations.

It is necessary, however, to bear in mind that the imprudent and

clumsy use of the equipment may lead to situations of death risk

for the user or third parties, as well as the damaging of the burner

or other items. Inattention, thoughtlessness and excessive

confidence often cause accidents; the same applies to tiredness

and sleepiness.

It is a good idea to remember the following:

The burner must only be used as expressly described. Any

other use should be considered improper and therefore

dangerous.

Specifically:

it can be applied to boilers operating with water, steam,

diathermic oil, and to other uses expressly named by the

manufacturer;

the type and pressure of the fuel, the voltage and frequency of the

electrical power supply, the minimum and maximum deliveries for

which the burner has been regulated, the pressurisation of the

combustion chamber, the dimensions of the combustion

chamber and the ambient temperature must all be within the

values indicated in the instruction manual.

Modification of the burner to alter its performance and

destinations is not allowed.

The burner must be used in exemplary technical safety

conditions. Any disturbances that could compromise safety

must be quickly eliminated.

Opening or tampering with the burner components is not

allowed, apart from the parts requiring maintenance.

Only those parts envisaged by the manufacturer can be

replaced.

3.2 Personnel training

The user is the person, body or company that has acquired the

machine and intends to use it for the specific purpose. He is

responsible for the machine and for the training of the people

working around it.

The user:

undertakes to entrust the machine exclusively to suitably

trained and qualified personnel;

undertakes to inform his personnel in a suitable way about

the application and observance of the safety instructions.

With that aim, the user undertakes to ensure that everyone

knows the use and safety instructions for his own duties;

Personnel must observe all the danger and caution

indications shown on the machine.

Personnel must not carry out, on their own initiative,

operations or interventions that are not within their province.

Personnel must inform their superiors of every problem or

dangerous situation that may arise.

The assembly of parts of other makes, or any modifications,

can alter the characteristics of the machine and hence

compromise operating safety. The manufacturer therefore

declines any and every responsibility for any damage that

may be caused by the use of non-original parts.

In addition:

3 Safety and prevention

ATTENTION

The manufacturer guarantees safety and proper

functioning only if all burner components are intact

and positioned correctly.

must take all the measures necessary to

prevent unauthorised people gaining access

to the machine;

the user must inform the manufacturer if

faults or malfunctioning of the accident

prevention systems are noticed, along with

any presumed danger situation;

personnel must always use the personal

protective equipment envisaged by legislation

and follow the indications given in this

manual.

7 20168481

Technical description of the burner

4.1 Burner designation

4.2 Models available

4.3 Burner categories - Countries of destination

4 Technical description of the burner

Designation Voltage Start-up Code

RLS 130 TC 3/220-380/60 Direct 20169069

Class 2 EN267 - Class 3 EN676

Series: R

Size

Fuel: Natural gas

Light oil

Gas oil / Methane

Adjustment:

Electrical supply of the system:

3/400/50

3/230/50

Voltage of auxiliaries:

230/50/60

110/50/60

RLS 130 TC

Emission: C11 or... Class 1 EN267 - EN676

C22 or MZ Class 2 EN267 - EN676

C33 or BLU Class 3 EN267 - EN676

3/220/50 220/60

BASIC DESIGNATION

EXTENDED DESIGNATION

3N / 400V / 50Hz

3 / 230V / 50Hz

230V / 50-60Hz

110V / 50-60Hz

Heavy oil

E Electronic cam

EV Electronic cam and variable speed (with Inverter)

P Proportional air/gas valve

BP Two stage (light oil) / Proportional valve (gas)

M Mechanical cam

Head: TC Standard head

TL Extended head

C23 or MX

MX Class 1 EN267 - Class 3 EN676

Flame control system:

FS1

FS2

Standard (1 stop every 24 h)

Continuous operation - only using the flame

detection electrode (ionisation)

FS1

Country of destination Gas category

SE - FI - AT - GR - DK - ES - GB - IT - IE - PT - IS - CH - NO I2H

DE I2ELL

NL I2L - I2E - I2 (43.46 ÷ 45.3 MJ/m3 (0°C))

FR I2Er

BE I2E(R)B

LU - PL I2E

20168481 8

Technical description of the burner

4.4 Technical data

Tab. A

(1) Reference conditions: Ambient temperature 20°C - Gas temperature 15°C - Barometric pressure 1013 mbar - Altitude 0 m a.s.l.

(2) Pressure at test point 7)(Fig. 4) with zero pressure in combustion chamber and at maximum burner output.

(3) Sound pressure measured in manufacturer's combustion laboratory, with burner operating on test boiler and at maximum output. The sound power

is measured using the "Free Field" method, required by the EN 15036 standard, and according to an “Accuracy: Category 3” measurement, as

described in EN ISO 3746.

4.5 Electrical data

Tab. B

Model RLS 130

Power(1)

Delivery (1) min - max kW

kg/h

465/930 ÷ 1395

39/78 ÷ 118

Fuels – Light oil, max. viscosity at 20 °C: 6 mm2/s (1.5°E - 6 cSt)

– Natural gas: G20 (methane) - G25

– LPG - G31 (butane)

Gas pressure at max. output (2) -

Gas: G20/G25/G31 mbar 11.5/14.4/15 - 360

Operation – FS1 - Intermittent (min. 1 stop in 24 hours)

– Two-stage (high and low flame) and one-stage (all - nothing)

Pump Output at 12 bar

Pressure range

Fuel temperature

kg/h

bar

°c max

220

10 - 20

Nozzles number 2

Standard applications Boilers: water, steam, diathermic oil

Ambient temperature °C 0 - 40

Combustion air temperature °C max 60

Noise levels (3) Sound pressure

Sound power dB(A) 80

Weight (including packaging) kg 99

Model RLS 130

Main electrical supply 3~ 220/380V 60Hz

Auxiliary circuit electrical supply 1N~ 220V 60Hz

Fan motor IE3 rpm

3470

220/380

2200

7.3 - 4.2

Pump motor rpm

3300

220

550

4.6

Pump motor capacitor µF 16

Ignition transformer V1 - V2

I1 - I2

230 V - 2 x 5 kV

1,9 A - 30 mA

Maximum absorbed electric power

Light oil

Gas

W Max.

3.5

2.9

Protection level IP 44

9 20168481

Technical description of the burner

4.6 Maximum dimensions

The dimensions of the burner are given in Fig. 1.

Note that to inspect the combustion head the burner must be

moved backward and turned upward. The maximum dimension

of the burner, without casing, when open is given by

measurement I.

Tab. C

(1) Blast tube: short-long

4.7 Burner equipment

Flange for gas train . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1

Seal for flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1

Flange fixing screws: M 10 x 35 . . . . . . . . . . . . . . . . . . . . . No. 4

Thermal flange gasket . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1

Screws to fix the burner flange to the boiler: M 12 x 35 . . . No. 4

Flexible hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 2

Nipples for flexible hoses with gaskets. . . . . . . . . . . . . . . . No. 2

Kit for LPG operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1

Label for LPG operation . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1

Spare parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1

Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1

Fig. 1

D1176

mm A B C D E F(1) GH I LMNO

RLS 130 733 338 395 555 840 250-385 189 430 1161 214 134 221 2”

20168481 10

Technical description of the burner

4.8 Firing rates

The burner cans work in two ways: one-stage or two-stage.

The MAXIMUM OUTPUT is chosen within area A and B. To use

also area B, the combustion head has to be pre-calibrated. See

"Combustion head pre-calibration” on page 17.

The MINIMUM OUTPUT must not be lower than the minimum

limit of the diagram: 465 KW = 39.0 kg/h

4.9 Test boiler

The burner/boiler combination does not pose any problems if the

boiler is EC approved and its combustion chamber dimensions

are similar to those indicated in the diagram (Fig. 3).

If the burner must be combined with a boiler that has not been EC

approved and/or its combustion chamber dimensions are clearly

smaller than those indicated in the diagram, consult the

manufacturer.

The firing rates were obtained in special test boilers, according to

EN 676 regulations.

In Fig. 3 you can see the diameter and length of the test

combustion chamber.

Example:

Output 650 Mcal/h (407 kW): diameter 60 cm - length 2 m.

MODULATING RATIO

The modulating ratio, obtained in test boilers, according to

standard (EN 676 for gas, EN 267 for light oil), is of 4:1 for light

oil and 7:1 for gas.

ATTENTION

The firing rate value (Fig. 2) has been obtained

considering an ambient temperature of 20 °C, an

atmospheric pressure of 1013 mbar (approx. 0 m

a.s.l.), and with the combustion head adjusted as

shown on page 19.

Pressure in the chamber

pressure - mbar

Thermal power - kW

Fig. 2

20168711

Fig. 3

Combustion chamber

D497

11 20168481

Technical description of the burner

4.10 Burner description

1 Combustion head

2 Ignition electrodes

3 Screw for combustion head adjustment

4 Pipe coupling

5 Screws to secure fan to pipe coupling

6 Fan motor

7 Flame stability disc

8 Boiler fixing flange

9 Gas input pipe

10 Pump

11 Air inlet to fan

12 Control box with lockout pilot light and reset button

13 Flame inspection window

14 Air damper

15 Slide bars for opening the burner and inspecting the

combustion head

16 Safety valve

17 1st and 2nd stage valves

18 Gas pressure test point and head fixing screw

19 Air pressure test point

20 Servomotor.

When the burner is not operating the air damper is fully

closed in order to reduce heat dispersion from the boiler

due to the flue draught which draws air from the fan suction

inlet.

21 Pump motor

Two types of burner lockout may occur:

CONTROL BOX LOCKOUT:

if the control box 12)(Fig. 4) push-button lights up, it indicates that

the burner is in lockout.

Press the push-button to reset.

MOTOR LOCKOUT:

release by pressing the push-button on thermal relay.

Fig. 4

20 21 11 10

431

20164424

20168481 12

Technical description of the burner

4.11 Electrical panel description

1 Ignition transformer

2 Switch for:

ON-OFF operation

Switch for:

1st and 2nd stage

3 Motor contactor and thermal relay with reset button

4 Led panel

5 Terminal board for electrical connection

6 Cable-grommets for external connections to be carried out

by the installer

7 Air pressure switch (differential type)

8 Control box base

9 Oil- gas switch

10 Flame sensor

11 Relay

68711 910

Fig. 5

20164425

13 20168481

Technical description of the burner

4.12 Control box RFGO-A22

Important notes

All interventions (assembly and installation operations,

assistance, etc.) must be carried out by qualified personnel.

Before modifying the wiring in the control box connection

area, fully disconnect the system from the power supply

(omnipolar separation).

Protection against electrocution from the control box and all

connected electric components is obtained with the correct

assembly.

Before any intervention (assembly and installation

operations, assistance, etc.), ensure the wiring is in order

and that the parameters are correctly set, then make the

safety checks.

Falls and collisions can negatively affect the safety

functions. In this case, the control box must not be operated,

even if it displays no evident damage.

For safety and reliability, comply with the following

instructions:

– avoid conditions that can favour the development of

condensate and humidity. Otherwise, before switching on

again, make sure that the entire control box is perfectly dry!

– Static charges must be avoided since they can damage the

control box’s electronic components when touched.

Use

The control box is a control and supervision system of medium

and large capacity forced draught burners.

If used with the flame detection electrode the system can operate

continuously whereas, with the use of UV sensors it operates

intermittently with stop and restart request at least once every

24h.

Installation notes

• Make sure that the electrical wiring inside the boiler complies

with national and local safety regulations.

• Do not confuse the powered conductors with the neutral

ones.

• Ensure that spliced wires cannot get into contact with

neighbouring terminals. Use adequate ferrules.

• Arrange the H.V. ignition cables separately, as far as

possible from the control box and the other cables.

• When wiring the unit, make sure that AC 230 V mains voltage

cables are run strictly separate from extra low-voltage cables

to avoid risks of electrical shock hazard.

Technical data

Tab. D

Electrical wiring of the flame detector

It is important for signal transmission to be almost totally free

of any disturbances or loss:

• Always separate the detector cables from the other cables:

– The capacitive reactance of the line reduces the size of the

flame signal.

– Use a separate cable.

• Respect the allowed cable lengths.

• The ionisation probe is not protected against the risk of

electrocution. When connected to the electricity supply, the

ionisation probe must be protected against any accidental

contact.

• Position the ignition electrode and the ionisation probe so

that the ignition spark cannot form an arc on the probe (risk

of electric overcharge).

ATTENTION

To avoid accidents, material or environmental

damage, observe the following instructions!

The control box is a safety device! Avoid opening

or modifying it, or forcing its operation. The

Manufacturer cannot assume any responsibility

for damage resulting from unauthorised work!

Mains voltage AC 230 V -15% / +10%

Mains frequency 50 / 60 Hz

Primary fuse (external) Refer to the electric

system

Weight approx. 1.1 kg

Power absorption approx. AC 7 VA

Protection level IP40

Safety class II

Environmental conditions

Operation

Climatic conditions

Mechanical conditions

Temperature range

Humidity

DIN EN 60721-3-1

Class 1K2

Class 1M2

-40...+60 °C

< 90% RH (non-condensing)

Fig. 6

20152163

20168481 14

Technical description of the burner

4.13 Servomotor (LKS 210 ...)

Important notes

All interventions (assembly and installation operations,

assistance, etc.) must be carried out by qualified personnel.

Before modifying the wiring in the connection area of the

servomotor, fully disconnect the burner control device from

the power supply (omnipolar separation).

To avoid the risk of electrocution, protect the connection

terminals in a suitable manner and correctly fix the cover.

Check the wiring is in order.

Falls and collisions can negatively affect the safety

functions. In this case, the servomotor must not be operated,

even if it displays no evident damage.

Assembly notes

• Check the relevant national safety standards are respected.

• When assembling the servomotor and connecting the

damper, the gears can be disengaged by means of a lever,

allowing the drive shaft to be easily adjusted in both

directions of rotation.

Technical data

Tab. E

ATTENTION

To avoid accidents, material or environmental

damage, observe the following instructions!

Avoid opening, modifying or forcing the

actuators.

MODEL LKS 210 - 10 ...

Operating voltage 200-240V - 50/60 Hz

Switching capacity

of auxiliary and limit switches 10 A/ 250V

Opening time 0-90°, 5 sec.

Firing angle 0 - 90°

Torque 1.5 Nm

Rotation direction Anticlockwise

Weight 0.7 kg

Protection level IP 44

MV2

–

Fig. 7

S9697

15 20168481

Installation

5.1 Notes on safety for the installation

After carefully cleaning all around the area where the burner is to

be installed, and arranging for the environment to be illuminated

correctly, proceed with the installation operations.

5.2 Handling

The burner packaging includes a wooden platform, it is therefore

possible to handle the burner (still packaged) with a pallet truck

or fork lift truck.

5.3 Preliminary checks

Checking the consignment

Checking the characteristics of the burner

Check the identification label of the burner, showing:

the model (A)(Fig. 8) and type of burner (B);

the year of manufacture, in cryptographic form (C);

the serial number (D);

the data for electrical supply and the protection level (E);

the absorbed electrical power (F);

the types of gas used and the relative supply pressures (G);

the data of the burner's minimum and maximum output

possibilities (H)(see Firing rate).

Warning. The burner output must be within the boiler's firing

rate.

The category of the appliance/countries of destination (I).

light oil maximum viscosity (L).

5 Installation

DANGER

All the installation, maintenance and disassembly

operations must be carried out with the electricity

supply disconnected.

ATTENTION

The installation of the burner must be carried out

by qualified personnel, as indicated in this manual

and in compliance with the standards and

regulations of the laws in force.

DANGER

The combustion air inside the boiler must be free

from hazardous mixes (e.g.: chloride, fluoride,

halogen); if present, it is highly recommended to

carry out cleaning and maintenance more

frequently.

ATTENTION

Burner handling operations can be highly

dangerous if not carried out with the greatest

attention: distance unauthorised personnel, check

integrity and suitability of the means available.

Check also that the area in which you are working

is empty and that there is an adequate escape

area (i.e. a free, safe area to which you can

quickly move if the burner should fall).

When handling, keep the load at not more than

20-25cm from the ground.

After positioning the burner near the installation

point, correctly dispose of all residual packaging,

separating the various types of material.

CAUTION

Before proceeding with the installation operations,

carefully clean all around the area where the

burner will be installed.

CAUTION

After removing all the packaging, check the

integrity of the contents. In the event of doubt, do

not use the burner; contact the supplier.

The packaging elements (wooden cage or

cardboard box, nails, clips, plastic bags, etc.)

must not be abandoned as they are potential

sources of danger and pollution; they should be

collected and disposed of in the appropriate

places.

ATTENTION

A burner label that has been tampered with,

removed or is missing, along with anything else

that prevents the definite identification of the

burner makes any installation or maintenance

work difficult.

Fig. 8

D9243

R.B.L.

GAS- KAASU

GAZ- AEPIO

0085

RIELLOS.p.A.

I-37045 Legnago (VR)

HEIZÖLFUEL

ABC

EDF

20168481 16

Installation

5.4 Operating position

5.5 Preparing the boiler

5.5.1 Boring the boiler plate

Pierce the closing plate of the combustion chamber, as in Fig. 10.

The position of the threaded holes can be marked using the

thermal insulation screen supplied with the burner.

Tab. F

5.5.2 Blast tube length

The length of the blast tube must be selected according to the

indications provided by the manufacturer of the boiler, and in any

case it must be greater than the thickness of the boiler door

complete with its fettling. The range of lengths available, L (mm),

is as follows:

Tab. G

For boilers with front flue passes 13) or flame inversion

chambers, a protection in heat-resistant material 11) must be

inserted between the boiler fettling 12) and the blast tube 10).

This protection must not compromise the extraction of the blast

tube.

For boilers with a water-cooled front piece, a refractory lining 11)-

12)(Fig. 11) is not necessary, unless expressly requested by the

boiler manufacturer.

5.5.3 Securing the burner to the boiler

Separate the combustion head from the rest of the burner

(Fig. 11):

disconnect the light oil pipes unscrewing the two unions 6);

loosen the 4 screws 3) and remove the cover 1);

remove screws 2) from the two slide bars 5);

remove the two screws 4) and pull the burner back on slide

bars 5) by about 100 mm.;

disconnect the electrode cables, then completely unthread

the burner from the slide bars.

ATTENTION

The burner is set up to operate only in

positions 1, 2, 3 and 4 (Fig. 9).

Installation 1 is preferable, as it is the only

one that allows the maintenance operations

as described in this manual.

Installations 2, 3 and 4 permit operation but

make maintenance and inspection of the

combustion head more difficult.

DANGER

Any other position could compromise the

correct operation of the appliance.

Installation 5 are forbidden for safety

reasons.

Fig. 9

2 3 4 51

D7739

mm A B C

RLS 130 195 275 - 325 M 12

mm RLS 130

Standard 250

Extended 385

Fig. 10

D455

Provide an adequate lifting system.

ATTENTION

The seal between burner and boiler must be

airtight.

Fig. 11

D1172

17 20168481

Installation

5.6 Access to head internal part

In order to reach inside the combustion head (Fig. 12) proceed as

follows:

remove the screw 1) and the internal part 2).

5.6.1 Combustion head pre-calibration

Check, at this point, whether the maximum output of the burner

in the 2nd stage is within area A or in area B of the firing rate. See

"Firing rates” on page 10.

– If it is in area A, no intervention is required.

– However, if it is in area B:

loosen the screws 1)(Fig. 13) and disassemble the blast

tube 2);

move the rod 3)(Fig. 13) from position A to position B,

thereby drawing back the shutter 4);

reassemble the blast tube 2)(Fig. 13) and the screws 1).

Once this operation (if necessary) has been carried out, fix the

flange 9)(Fig. 11 on page 16) to the boiler plate, interposing the

insulating gasket 7)(Fig. 11 on page 16) supplied. Use the 4

screws, also supplied with the unit, after protecting the thread

with anti-seizing product.

5.7 Electrode positions

Be careful as some drops of fuel may leak out

during this phase.

Fig. 12

D1122

Fig. 13

D1192

ATTENTION

Check that the electrodes are positioned

correctly, as in Fig. 14, complying with the

dimensions indicated.

Fig. 14

D1124

20168481 18

Installation

5.8 Nozzle installation

The burner complies with the emission requirements of the EN

267 standard. In order to guarantee that emissions do not vary,

recommended and/or alternative nozzles specified by Riello in

the Instruction and warning booklet should be used.

Remove the screw 1) and the internal part 2)(Fig. 15).

Assemble the two nozzles with the socket spanner 1)(A

Fig. 16) (16mm), after removing the plastic plugs 2)(A

Fig. 16), passing from the central opening of the flame

stability disc. Alternatively, loosen the screws 1)(B Fig. 16),

remove the disc 2)(B Fig. 16), and replace the nozzles using

the spanner 3)(B Fig. 16).

The nozzle for the 1st stage of operation is the one beneath

the ignition electrodes, Fig. 14 on page 17.

Reassemble the burner on the guides 3)(Fig. 17) at about

100 mm from the pipe coupling 4), burner in the position

shown in Fig. 11 on page 16;

insert the electrode cables and then slide the burner up to

the pipe coupling, the burner in the position indicated in

Fig. 17;

refit screws 2)(Fig. 17) on slide bars 3);

fix the burner to the pipe coupling with the screws 1);

reconnect the light oil pipes by screwing the two fittings

6)(Fig. 11 on page 16).

5.8.1 Recommended nozzle

Both nozzles must be chosen from among those listed in table

(Tab. H).

The first nozzle determines the delivery of the burner in the 1st

stage.

The second nozzle works together with the 1st nozzle to

determine the delivery of the burner in the 2nd stage.

The deliveries of the 1st and 2nd stages have to be within the

value range indicated Tab. A on page 8.

Use nozzles with a 60° spray angle at the recommended

pressure of 12 bar.

In general both nozzles have the same delivery.

Tab. H

ATTENTION

It is advisable to replace the nozzle once a year

during periodical maintenance.

CAUTION

The use of nozzles other than those specified by

Riello S.p.A. and inadequate regular maintenance

may result into emission limits non-conforming to

the values set forth by the regulations in force, and

in extremely serious cases, into potential hazards

to people and objects.

The manufacturing Company shall not be liable

for any such damage arising from non-

observance of the requirements contained in this

manual.

ATTENTION

Do not use any sealing products such as:

gaskets, tape or sealants.

Be careful to avoid damaging the nozzle

sealing seat.

The nozzle must be screwed into place tightly

but not to the maximum torque value

provided by the wrench.

ATTENTION

On closing the burner on the two guides it is

advisable to gently pull the high voltage wires

outwards until they are under slight tension.

GPH

Kg/h kW

10 bar 12 bar 14 bar 12 bar

5.00

5.50

6.00

6.50

7.00

7.50

8.00

8.30

8.50

9.00

9.50

10.0

10.5

11.0

12.0

12.3

13.0

13.8

14.0

15.0

15.3

16.0

17.0

19.2

21.1

23.1

25.0

26.9

28.8

30.8

31.9

32.7

34.6

36.5

38.4

40.4

42.3

46.1

47.3

50.0

53.1

53.8

57.7

58.8

61.5

65.4

21.2

23.3

25.5

27.6

29.7

31.8

33.9

35.2

36.1

38.2

40.3

42.4

44.6

46.7

50.9

52.2

55.1

58.5

59.4

63.6

64.9

67.9

72.1

23.1

25.4

27.7

30.0

32.3

34.6

36.9

38.3

39.2

41.5

43.8

46.1

48.4

50.7

55.3

56.7

59.9

63.3

64.5

69.2

70.5

73.8

78.4

251.4

276.3

302.4

327.3

352.3

377.2

402.1

417.5

428.2

453.1

478.0

502.9

529.0

553.9

603.7

619.1

653.5

693.8

704.5

754.3

769.7

805.3

855.1

Fig. 15

D1122

Fig. 16

D1146 D1147

Fig. 17

20164422

Riello RLS 130 TC LP FS1 3/208-230/380/60 230/50-60 Installer Manual

Related papers

Other documents