Bay Networks CLAM Quick start guide

Type
Quick start guide

Bay Networks CLAM is a revolutionary networking device that simplifies and enhances your networking capabilities. With its self-learning intelligence, the CLAM streamlines the configuration process, adapting to your network environment and optimizing performance. Whether you're connecting to the internet or bridging multiple networks, the CLAM delivers seamless and secure connectivity with ease.

Bay Networks CLAM is a revolutionary networking device that simplifies and enhances your networking capabilities. With its self-learning intelligence, the CLAM streamlines the configuration process, adapting to your network environment and optimizing performance. Whether you're connecting to the internet or bridging multiple networks, the CLAM delivers seamless and secure connectivity with ease.

I
SSUE
3.0 MAN-CLAM-BRIDGE-EZ START
CLAM B
RIDGE
EZ START G
UIDE
Issue 3.0
All rights reserved. This document may not be in whole or in part
copied, photocopied, reproduced, translated or reduced to any
electronic medium or machine-readable form without the prior written
permission of Bay Networks Inc.
The information contained in this manual is believed to be accurate.
However, no responsibility whatsoever is assumed by Bay Networks
Inc. for its use, nor for any infringements of patents or other rights of
third parties resulting from its use.
All trade marks are acknowledged.
1996 Scorpion Logic Ltd. a Bay Networks company
MAN-CLAM-BRIDGE-EZ START I
SSUE
3.0
EZ
S
TART
Issue 3.0 Page 1
Safety and Homologation Statements
BABT Statements (European Standards)
The CLAM has been approved by BABT for connection to the I-CTR3
standard ISDN service under the Approval Number AA604444 and it is
important that the user is familiar with the conditions of use as described in
this manual.
The CLAM is approved for operation under the General Approval Number
NS/G/1234/J/100003.
EMC
This Device complies with the requirements of EMC with EN55022-A
(emissions) and EN50081-1 (susceptibility) approvals.
Germany
This device complies with the German delta specifications BAPT 223 ZV25
for EURO-ISDN, with Approval Number A120 186F.
France
This device complies with the French delta specifications CES P10-21 A for
EURO-ISDN, with Approval Number ni96063B.
Switzerland
This device is approved for use in Switzerland with approval number
BAKOM 95.0938.1.N.
FCC Class B statement (USA Operation)
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
EZ
S
TART
Page 2 Issue 3.0
Warning: Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
Canadian EMI Statement
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appariel numorique de la classe B respect toutes les exigences du
Rpglement sur le matoriel brouilleur du Canada.
EZ
S
TART
Issue 3.0 Page 3
Thank you for adding the CLAM to your networking environment. CLAM
revolutionises traditional networking by including the intelligence to self-
learn many parameters. You should find the CLAM easy to install and use,
especially if you follow the step-by-step instructions relevant to your CLAM
configuration in this “Easy Start” guide. When you become familiar with
the CLAM and its management as described in the EZ S
TART
G
UIDE
, the
R
EFERENCE
M
ANUAL
will provide more detailed information.
The physical installation should take place on a flat surface, in a clean, dry
location with no extreme temperatures. Make sure that all services needed
(power, LAN, ISDN, etc.) are within reach and are working correctly.
The CLAM can be located almost anywhere that is convenient for
connection to the power supply, the LAN and ISDN, as long as temperature
and humidity conditions are met. There should be an air gap above and on
all sides of the CLAM, to ensure that the maximum temperature limit is not
reached.
Parameter Specification
Power Supply (Europe and U.K.) 220-240V AC 50Hz (nominal)
Power Supply (North America) 100-125V AC 60Hz (nominal)
Supply Current 60 mA
Power Consumption 15 Watts
Operating Temperature 5 to 45 degrees C
Humidity 5% to 95% (non-condensing)
LAN Cable Maximum Length 100m
Before you start the installation:
MAKE SURE YOU HAVE EVERYTHING YOU NEED
The checklists in the following sections should help to make sure you have
everything you need for a successful first-time installation.
EZ
S
TART
Page 4 Issue 3.0
1. C
HECKLISTS AND
U
NPACKING
1.1 Y
OUR
ISDN S
ERVICE
C
HECKLIST
If you wish to use ISDN to connect your CLAM to other devices, please
read this section for further details.
1.1.1 E
UROPEAN
S
ERVICES
Your ISDN circuit should conform to EURO-ISDN (otherwise known as
NET3 or iCTR3) standards.
Each ISDN BRI (Basic Rate Interface) should terminate in a wall socket
RJ-45 interface.
You should know the ISDN number(s) of your local and remote sites.
If you require CLI (Calling Line Identification) for security, then order
the CLI option from your local carrier.
If possible, order both B Channels to have the same ISDN number. This
is sometimes known as Auxiliary Working and can speed up connect
times.
1.1.2 N
ORTH
A
MERICAN
S
ERVICES
In North America you must configure your ISDN BRI ports for the type of
switch your telephone company has in its local central office. Please see the
booklet Ordering Basic Rate ISDN (shipped with North American product
variants only) for full details. You need the following items of information
from your telephone company:
Whether your line is configured in the standard National ISDN mode, or
in a manufacturer-specific “custom” mode.
Whether the ISDN link is a Point-to-Point or a Multipoint interface.
The type of switch: National ISDN2, AT&T 5ESS5, Northern Telecom
DMS-100/DMS-250, or Siemens EWSD.
The local directory number(s) assigned to the line.
EZ
S
TART
Issue 3.0 Page 5
The SPIDs (Service Profile Identifiers) for the local directory number(s).
1.2 Y
OUR
N
ETWORK
C
HECKLIST
The networks to be connected must be configured correctly. The following
sections list specific protocol requirements.
1.2.1 S
PECIFIC
P
ROTOCOLS
S
UPPORTED
When using ISDN, the CLAM has extra support for the following
protocols:
1. TCP/IP
2. Novell Netware IPX/SPX
3. Banyan Vines
4. pcAnywhere
IF YOU WISH TO USE ANY OTHER NETWORK PROTOCOLS,
PLEASE CONTACT YOUR SUPPLIER FOR ADVICE.
1.2.2 TCP/IP C
HECKLIST
All devices should have an established IP Address (usually defined by the
network administrator).
An IP Address must be assigned to the CLAM itself (usually defined by
the network administrator).
The Network or sub-network numbers must be the same on the local and
remote networks to be bridged.
1.2.3 N
OVELL
N
ETWARE
C
HECKLIST
Devices on the local site and the remote sites will require the same Novell
External Network Numbers.
EZ
S
TART
Page 6 Issue 3.0
For each External Network Number, the Frame Type must be the same at
the local and the remote sites.
1.2.4 B
ANYAN
V
INES
C
HECKLIST
One of the two networks to be bridged must have a Banyan server/router
installed.
The workstation software should preferably be of the same revision as the
server to which it will connect.
1.2.5
PC
A
NYWHERE
C
HECKLIST
Confirm that you are running pcAnywhere over Novell IPX.
Devices on the local site and the remote sites will require the same Novell
External Network Numbers.
For each External Network Number, the Frame Type must be the same at
the local and the remote sites.
EZ
S
TART
Issue 3.0 Page 7
1.3 P
ACKAGING
C
HECKLIST
Please check that the following items came in your CLAM Bridge package:
One CLAM Bridge
One PSU (Power Supply Unit - 9V DC output) with jack plug
One 10BASE-T Ethernet cable
One ISDN cable
One CLAM Bridge manual
One DB9 (9-way) to RJ-45 cable adapter
Four rubber feet
Four Velcro feet
Two Velcro pads
If any of these items are missing, please call your supplier.
1.3.1 F
ITTING
R
UBBER OR
V
ELCRO
F
EET
The CLAM may be fitted either with rubber feet for free-standing use or
Velcro feet for attaching the CLAM to a workbench or to the side of a PC.
On the underside of the CLAM are four marked circles. If rubber feet are
to be fitted, peel off the backing from each foot and press the sticky side of
each foot into the middle of a marked circle. Velcro feet are fitted in the
same way: peel off the backing of the Velcro feet, and press the sticky side
of each foot into the middle of a marked circle.
Screw Location
The Velcro pad on which the CLAM is to stand should fit on a clean surface
free of dust. Peel off the backing, and press the pad firmly into place.
EZ
S
TART
Page 8 Issue 3.0
2. C
ONNECTING THE
CLAM
TO YOUR
LAN
OR
PC
CLAM REAR VIEW
9 v DCLAN ISDN
Combined
10BaseT and
manager port
BRI port
To external
PSU
Analogue
Input Port for
Fax/Phone
(NOT AVAILABLE IN
ALL TERRITORIES)
2.1 D
IRECT
PC
OR
T
ERMINAL
C
ONNECTION
If the CLAM is to be plugged directly into the back of a PC, terminal, or
workstation, it emulates a 10BASE-T HUB.
1) Connect the Twisted Pair LAN
cable from the 10BASE-T port
on your PC or workstation into
the port marked LAN on the
CLAM.
9 v DCLAN ISDN
EZ
S
TART
Issue 3.0 Page 9
2.2 C
ONNECTING TO
Y
OUR
L
OCAL
LAN HUB
Before opening up the CLAM, always make sure it is disconnected from
the POWER SUPPLY.
If the CLAM is to connect to a HUB repeater: open the CLAM and move
the four jumpers next to the LAN port into the “TCVR” setting.
1) Close the case again carefully,
making sure that the LED fits
in the hole provided for it.
2) Connect the Twisted Pair LAN
cable from the 10BASE-T port
on your local HUB to the port
marked LAN on the CLAM.
HUB
TCVR
LAN
Set Jumpers to HUB
to connect to back of workstation
Set Jumpers to TCVR to
connect to Repeater/HUB
Alternatively, a 10BASE-T Cross-over cable may be used.
9 v DCLAN ISDN
EZ
S
TART
Page 10 Issue 3.0
3. C
ONNECTING TO THE
M
ANAGEMENT
S
YSTEM
The CLAM contains a built-in configuration and management system for
use via a local async terminal, or on the LAN via a TCP/IP Telnet session.
3.1 L
OCAL
T
ERMINAL
C
ONNECTION
Initial configuration of the CLAM may be done using a VT-100 type async
terminal, or a PC with a communications package emulating a VT-100. To
set up Windows TERMINAL, use the Settings in the screen shots below:
Windows TERMINAL Setup
EZ
S
TART
Issue 3.0 Page 11
1) Connect the DB9 to RJ-45
adapter to one end of the
Manager cable, then plug the
other end into the port marked
LAN at the back of the CLAM.
2) Plug the DB9 to RJ-45 adapter
into the DB9 serial port on the
PC, terminal or workstation.
9 v DCLAN ISDN
Set up the terminal or communications package with the following
parameters for the serial interface:
- 9600 bps
- 8 data bits
- 1 stop bit
- no parity.
3.2 T
ELNET
C
ONNECTIONS
When you first receive your CLAM, it will be unconfigured, with 1.1.1.1 as
its default IP address. The Management System can be accessed initially by
a Telnet call from your TCP/IP workstation to this address, after setting your
workstation to a spare IP address on network 1.0.0.0 (subaddress mask
255.0.0.0).
To change the CLAM address, see I
NITIAL
C
ONFIGURATION
section below.
EZ
S
TART
Page 12 Issue 3.0
4. C
ONNECTIONS TO
ISDN
AND
V
OICE
4.1 EURO-ISDN C
ONNECTIONS
1) Connect the flat ISDN cable
from the ISDN wall socket to
the socket marked ISDN on
the CLAM.
9 v DCLAN ISDN
ISDN Wall
Jack
4.2 USA ISDN U I
NTERFACE
C
ONNECTIONS
If your CLAM has a Basic Rate ISDN ‘U’ interface, connect the flat ISDN
cable from the ISDN wall socket (either an RJ-11 or RJ-45 socket) into the
socket marked ISDN BRI on the CLAM. If your CLAM has an ‘S/T’
interface, an
external
NT1 is needed to convert the ‘S/T’ to a ‘U’ interface.
1) Connect the ISDN ribbon
cable from the ISDN S-
Interface (
terminal
) on the
NT1 to the socket marked
ISDN on the CLAM.
2) Connect the ISDN cable from
the ISDN wall socket to the U-
Interface (
line
) on the NT1.
3) Connect the NT1 to the AC
power supply and turn the
power on.
9 v DCLAN ISDN
ISDN Wall
Jack
AC Power
S-Inerface U-Inerface
ISDN NT-1
Warning: DO NOT plug the cable from an NT1 into the LAN socket
(10BASE-T and Manager), as the CLAM will be seriously damaged by
the 48V DC which the NT1 provides as a power supply for ISDN
telephones (on pins 7 and 8 of its terminal connector).
EZ
S
TART
Issue 3.0 Page 13
4.3 O
PTIONAL
A
NALOGUE
M
ODULE
C
ONNECTIONS
If your CLAM has an analogue voice module (optional), the back of the unit
will be as shown below.
1) Connect an analogue device (e.g. telephone, modem or fax) to the RJ-11
port marked VOICE. UK models are supplied with a converter from an
RJ-11 to a BT Master Socket. This should be connected between the
device and the voice port.
9 v DCLAN
ISDN
ISDN2
Service
AC Power
VOICE
For reference, the analogue connection is made via pins 3 & 4 (the two
centre pins) of the RJ-11 socket.
To test the connection, see the section
C
ONNECTING VIA AN
A
NALOGUE
D
EVICE
below.
EZ
S
TART
Page 14 Issue 3.0
5. C
ONNECTING
P
OWER
5.1 P
OWER
C
ONNECTION AND
I
NDICATORS
1) Switch the power supply ON.
2) The LED on top of the CLAM
should change colour as
follows:
RED (for 2 to 5 seconds)
AMBER(2 to 10 seconds)
GREEN (CLAM ready).
3) The CLAM is now
operational.
9 v DCLAN ISDN
ISDN Wall
Jack
AC Power
The LED may be in one of the following states:
GREEN NORMAL state
GREEN flashing ISDN call in progress
RED flashing Fault
RED Re-booting (or, if permanently on, Fault)
AMBER flashing Unit in boot mode (during Software upgrade)
EZ
S
TART
Issue 3.0 Page 15
6. A
CCESSING THE
CLAM M
ANAGER
All configuration and management tasks can be completed with the
Manager System, which can be accessed either via the Manager Port or via
the LAN.
6.1 T
ERMINAL
A
CCESS VIA
M
ANAGER PORT
1. Hitting any key shows the PASSWORD prompt on a blank screen:
Enter Password [...............]
2. Type PASSWORD <Return> (Note: UPPER case required)
You now have access to the CLAM Manager.
6.2 N
ETWORK
A
CCESS VIA THE
LAN
USING
TCP/IP
1. To connect to the Manager Port from a PC or workstation, make a Telnet
call to address 1.1.1.1; when the connection is made, the PASSWORD
prompt is shown:
Enter Password [...............]
2. Type PASSWORD <Return> (Note: UPPER case required)
You now have access to the CLAM Manager.
Note: Manager forms are submitted and actioned immediately by typing
^E (<CONTROL> E)
If you make a mistake in a form, the form can be discarded by typing
^L (<CONTROL> L)
EZ
S
TART
Page 16 Issue 3.0
7. CLAM C
ONFIGURATIONS
7.1 G
IVING
Y
OUR
CLAM
A
N
AME AND
A
DDRESS
To work successfully, your CLAM needs a name to identify itself, as well as
an IP address.
7.1.1 I
NITIAL
C
ONFIGURATION
The following initial setup should be done on all CLAM installations, using
the COnfigure SYstem form.
Set the CLAM Name. This name should be descriptive, but must be
unique within the set of CLAMs likely to talk to each other. Note: the
name should not include blank spaces, punctuation or special characters,
except _ (underscore).
Set the CLAM IP Address. This address should be provided by the
network administrator, and should be consistent with your company
addressing policy. Note that if you change the IP Address over TCP/IP,
then the current session will hang up: you must disconnect the session
and then TELNET again using the new IP Address.
If required, set the CLAM password. Note: passwords are case-sensitive.
After completing any (re-)configuration, always type SAVE to ensure that
the changes made are maintained across power cycles.
7.1.2 C
ONFIGURATION FOR
Y
OUR
N
ETWORK
E
NVIRONMENT
As the CLAM is a very flexible unit that can be used in a wide variety of
configurations, the next step of the configuration process depends on your
working environment. The following examples do not cover all cases, but
your configuration may be very similar to one of the environments below.
EZ
S
TART
Issue 3.0 Page 17
7.1.3 TCP/IP UNIX
ENVIRONMENT
CorporateBridge
OfficeCLAM
MainLAN
OfficeLAN
ISDN
Repeater
Repeater
Server1 Server2
Workstation
Router
SubLAN
192.0.1.1
192.0.1.2
192.0.1.3
192.0.1.4
192.0.1.5
192.0.1.6
192.0.1.7
192.0.2.nnn
UNIX Host
Figure 7-1 Typical TCP/IP Environment
The CLAM can be set up to recognise IP traffic. Once this is done, the
CLAM makes the ISDN calls needed when a user has data to send or
receive, and ends the ISDN calls when the links are idle. First, the topology
of the IP network must be configured manually into each bridge as follows:
EZ
S
TART
Page 18 Issue 3.0
1. Use the COnfigure ISDN NUmbers form on the OfficeCLAM to add the
ISDN numbers of all remote bridges (see Figure 7-1). Add an entry for
each bridge likely to be connected. Unit names must match exactly the
names of the remote units (e.g. upper and lower case). On the remote
bridge, add the name OfficeCLAM to the list of ISDN numbers.
2. Use the COnfigure ISDN AUTOcalls form on the CLAM to set up the
Autocall table. An Autocall entry defines which packet destination will
start an ISDN connection. The CLAM understands IP addressing and
subnetting. For the network in Figure 7-1, the following entries should
be made in the Autocall tables of the two bridges:
OfficeCLAM Autocall table
Address Type Remote unit name
192.0.1.4/32 ARP/IP CorporateBridge
192.0.1.5/32 ARP/IP CorporateBridge
192.0.1.6/32 ARP/IP CorporateBridge
192.0.1.7/32 ARP/IP CorporateBridge
192.0.2.0/24 ARP/IP CorporateBridge
CorporateBridge Autocall table
Address Type Remote unit name
192.0.1.1/32 ARP/IP OfficeCLAM
192.0.1.2/32 ARP/IP OfficeCLAM
192.0.1.3/32 ARP/IP OfficeCLAM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34

Bay Networks CLAM Quick start guide

Type
Quick start guide

Bay Networks CLAM is a revolutionary networking device that simplifies and enhances your networking capabilities. With its self-learning intelligence, the CLAM streamlines the configuration process, adapting to your network environment and optimizing performance. Whether you're connecting to the internet or bridging multiple networks, the CLAM delivers seamless and secure connectivity with ease.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI