Microdia FlashMover Installation guide

Category
Card readers
Type
Installation guide
USB2.0 CF-DIRECT CARD READER
INSTALLATION GUIDE
Thank you for purchasing MICRODIA
®
FlashMover
®
USB2.0 CF-Direct Card Reader. The FlashMover
®
USB2.0
CF-Direct Card Reader works with USB enabled Microsoft Windows 98, ME, 2000, XP or above and Mac 9/X and
higher systems. This installation guide contains all the information you need to install your FlashMover
®
USB2.0
CF-Direct Card Reader.
USB2.0 CF-Direct Card Reader Installation Guide
Nov 2006 MICRODIA Ltd.
For Windows Users
To install the FlashMover
®
USB2.0 CF-Direct Card Reader on Windows 98/98SE:
1. Do not plug the card reader into the PC USB port before the installation is completed.
2. Download the driver from www.microdia.com
or insert the Driver CD in the CD-ROM drive.
3. Double click the file after downloading or the CD-ROM will auto-run and pop out a Driver Installation Manual
window.
4. In the Driver Installation Manual, select [Compact Flash]
5. The driver installation program will start to run and follow the installation instruction
6. After installation, reboot your computer.
7. Plug in your card reader into the USB port.
8. There is a new removable drive added to your computer.
9. Insert Compact Flash
TM
Card to access files in your card.
NOTE: Please check MICRODIA
®
website, www.microdia.com, for downloading the latest driver.
To install the FlashMover
®
USB2.0 CF-Direct Card Reader on Windows ME/2000/XP:
1. Plug the card reader into your computer USB port.
2. It is fully Plug-&-Play for Windows ME/2000/XP, no driver installation needed.
3. A new removable drive is added to your computer after plug in the card reader.
4. Insert Compact Flash
TM
Card to access files in your card.
For Macintosh Users
To install the FlashMover
®
USB2.0 CF-Direct Card Reader on Mac OS 8.6
1. Do not plug the card reader into the USB port before the installation is completed.
2. Download the driver from www.microdia.com
or insert the Driver CD in the CD-ROM drive.
3. Double click the file after downloading or the CD-ROM will auto-run and pop out a Driver Installation Manual
window.
4. In the Driver Installation Manual, select [Compact Flash]
5. The driver installation program will start to run and follow the installation instruction
6. After installation, reboot your computer.
7. Plug in your card reader into the USB port.
8. There is a new removable drive added to your computer.
9. Insert Compact Flash
TM
Card to access files in your card.
NOTE:
- Please check MICRODIA
®
website, www.microdia.com, for downloading the latest driver.
-
Please go to Mac website to update the latest version of Mac OS.
To install the FlashMover
®
USB2.0 CF-Direct Card Reader on Mac OS 9 and above
1. Plug the card reader into your computer USB port.
2. It is fully Plug-&-Play for Mac OS9 and above, no driver installation needed.
3. A new removable drive is added to your computer after plug in the card reader.
4. Insert Compact Flash
TM
Card to access files in your card.
Removing your CF
TM
card from the FlashMover
®
USB2.0 CF-Direct Card Reader
To remove the Compact Flash
TM
card on Windows system
1. Close any files that are opened and reside on the Compact Flash
TM
card.
2. You can remove your card safely after the LED stop blinking
To remove the Compact Flash
TM
card on Mac system
1. The Compact Flash
TM
card must be [EJECTED] or [UN-MOUNTED] by dragging the card’s disk icon in the trash.
CAUTION: Failure to properly [EJECT] the card before removing the card from the card reader could case data loss
or corruption.
Most problems or technical issues can be resolved by simply visiting our Support Section in MICRODIA
®
website,
www.microdia.com
or send us an email to [email protected]om.
  • Page 1 1
  • Page 2 2

Microdia FlashMover Installation guide

Category
Card readers
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI