Episode ES-SUB-IW-DUAL8 Owner's manual

Brand: Episode

Model: ES-SUB-IW-DUAL8

Type: Owner's manual

Episode ES-SUB-IW-DUAL8 is a high-quality subwoofer designed to enhance your home audio experience. With its powerful 500-watt amplifier and dual 8-inch woofers, it delivers deep, rich bass that will bring your music and movies to life. The ES-SUB-IW-DUAL8 is also easy to install, with a variety of mounting options that make it suitable for any room in your home. Whether you're looking to add some extra oomph to your music or enjoy your movies with truly immersive sound, the Episode ES-SUB-IW-DUAL8 is the perfect choice.

INSTALLATION MANUAL

ES-SUB-IW-DUAL8

page | 2

snapav.com Support 866.838.5052

INTRODUCTION

Thank you for purchasing Episode® speakers. To complete installation,

follow these guidelines. Visit our website for design recommendations and

speaker calculators.

SETUP

Subwoofer Placement

Episode® subwoofers are designed to make your music and movies come

alive. However, the placement of the subwoofer can affect its performance.

All rooms are different, but the strongest output will likely occur if you

place your subwoofer in the front of the room on the same wall as your

front channel speakers.

Keep subwoofer about 2 feet away from corners and other surfaces that

might interfere with or reflect sound, such as tall furniture.

Existing Construction Install

Make a cutout for the speaker using the supplied template. Allow space

for the bezel if installing near adjacent objects, or cut the hole in two steps

as shown below.

1. Cut the drywall at a 45° angle so that if the

speaker is too close to an obstruction, you

can easily ‘plug’ the hole.

2. If there are no obstructions, cut the drywall

again, this time at a 90° angle.

3. Insert the speaker into the cutout.

OBSTRUCTION

PLUG

page | 3

SECURE

Tighten each of the six screws to clamp the subwoofer

against the wall.

When mounting next to a stud, ensure there is enough

room for the dog legs to rotate out and clamp the stud.

Place the grill over the subwoofer, making sure it is

flush against the wall.

CAUTION: Do not overtighten screws. This could

result in damage to both the subwoofer and wall.

CONNECT

EA-AMP-SUB-1D-500R

1. Connect receiver directly to EA-AMP-SUB-1D-500R amplifier.

2. Connect speaker(s) to amplifier observing proper polarity (+ to + and

– to – ).

AV Receiver

SUB

CEN

Switched

Outlet

+12V Trigger

Out

Left & Right

Preamp Out

LFE Sub Out

(LFE)

OUT

IN IR UPDATE

OPERATE

TRIGGER

DC 12V

EA-AMP-SUB-1D-500R

SUB 1

SUB 2

Total Impedance

(Sub 1 + Sub 2) Minimum 4Ω

100-120V AC

220-240V AC

FUSE T8AL/250V

100-120V~60Hz/220-240V~50Hz 500WATTS

Designed and Engineered in USA

Made in China

ES-SUB-IW-DUAL8 ES-SUB-IW-DUAL8

FINE TUNE

Fine tune the subwoofer after all connections and calibrations are

complete.

WARRANTY

Limited Lifetime Warranty

Episode® speakers have a Limited Lifetime Warranty. This warranty

includes parts and labor repairs on all components found to be defective

in material or workmanship under normal conditions of use. This

warranty will not apply to products that have been abused, modified,

or disassembled. Products to be repaired under this warranty must be

returned to SnapAV or a designated service center with prior notification

and an assigned Return Authorization number (RA).

CONTACTING TECHNICAL SUPPORT

866.838.5052

[email protected]

Rev: 151214-1510

Episode ES-SUB-IW-DUAL8 Owner's manual

Episode ES-SUB-IW-DUAL8 Owner's manual

Episode ES-SUB-IW-DUAL8 Owner's manual

Related papers

Other documents