Peak Pilates Classic Cadillac Installation guide

Brand: Peak Pilates

Model: Classic Cadillac

Type: Installation guide

This manual is also suitable for

Cadillac (Premier & Classic)

, Spinner

, Spinning

, the Spinning logo, Peak Pilates

, and

Resist-A-Ball

are registered trademarks that are owned or used under exclusive license by Mad Dogg Athletics, Inc.

North America

2111 Narcissus Court

Venice, CA 90291 USA

310.823.7008

800.847.7746

Mad Dogg Athletics, Inc.

2111 Narcissus Court Venice, CA

90291 USA

800.847.7746 or 310.823.7008

[email protected]

Mad Dogg Athletics, Inc. Europe B.V.

Scheldeweg 3

3144 ES Maassluis

The Netherlands

+31 1059 04508

[email protected]

www.peakpilates.com

(Trapeze Table)

Installing the Springs

Leg Springs

The leg springs are the longest springs. Using double ended clips at each

end, attach these springs to the eyebolts in the roll down upright poles

(opposite the push-through bar). If you have the optional leg-spring slider

bar, attach the leg springs to its eyebolts using double ended clips. The

leg springs can be adjusted between the eyebolts depending on the height

and desired tension.

Arm Springs

Arm springs are the smallest in diameter. Use double ended clips to

attach these to the roll-down bar (the round wooden bar with eyebolts at

each end) and to the eyebolts in the roll-down cross pole. To perform the

standing arm exercise series, attach the arm springs to the eyebolts on the

back of the upright poles.

ASSEMBLY GUIDE

Recommended Use

Storing the Push-Through Bar

Installing the Fleece Hanging Straps

Peak Pilates strongly recommends consulting a physician for a complete medical exam before beginning any exercise program. Having a complete medical exam is

particularly important if the user has a family history of high blood pressure, has heart disease, is over the age of 45, smokes, has high cholesterol, is obese, or has not

exercised regularly in the past year.

If, at any time while exercising, the user feels faintness, dizziness, pain, or shortness of breath, he or she must stop immediately.

Important: This manual contains safety and usage information. Before beginning exercise, read the entire manual paying speciﬁc attention to all cautions and

warnings and obtain qualiﬁed instruction on the use of the Peak Pilates Premier or Classic Cadillac. Use only for the intended exercise. Do not modify the machine.

Modifying the machine in any way will nullify your warranty. Keep this guide handy for future reference.

Unsafe or improper use of this equipment due to failure to read and comply with all requirements and warnings could result in serious injury. Because Peak Pilates cannot

anticipate every situation and condition that can occur while using the Peak Pilates Cadillacs, we make no representation concerning the safety of this equipment.

There are risks associated with the use of any exercise equipment. The user assumes the responsibility for those risks.

Safety Statement

It is the responsibility of the purchaser of the products to instruct all individuals, whether they are end users or supervising personnel, on the proper use of the equipment.

Inspect the machine including all hardware, wood and fabric components before use. Do not exercise on the machine if signs of excessive wear, loose hardware, or other

defects are evident. Do not attempt to ﬁx a defective machine. Instead, notify Peak Pilates immediately.

NOTE: We strongly recommend that all users of Peak Pilates exercise equipment be informed of the following prior to use:

Proper Use

1. This equipment is only to be used as described by the manufacturer. It is imperative that the Cadillac be used properly to avoid injury.

2. Use only components provided by the manufacturer. Do not use parts or accessories or modify the machine in any way not approved by Peak Pilates.

3. Keep a three foot area (about one meter) around the equipment clear of obstructions.

4. Make sure the machine is used on a level surface.

Speciﬁc Operating Warnings

1. Be certain that all hardware is fully tightened before beginning to exercise.

2. Verify that no gaps between the coils or other defects are evident in the springs. If any defects are seen, the spring/springs must be immediately replaced.

3. Before using either of the push-through bar springs, verify that the end with the safety link is connected to either the frame or the tower - bottom or top push-through

bar spring respectively - and the end with the quick snap clip with thumbscrew is connected to the push-through bar. The thumbscrew must be tightened on all connecting

clips.

4. Verify that no tears or excessive wear are evident in the leather straps, ropes, handles, or loops . If excessive wear is evident the strap, handle or loop must be

immediately replaced.

5. Do not tip the machine during use.

6. Children must not be allowed near this machine. Teenagers and/or physically challenged individuals require supervision.

7. Keep hair, clothing, jewelry and other loose items clear of moving parts at all times.

8. It is the purchaser’s sole responsibility to instruct end users and supervising personnel on the proper operating procedures of the Cadillac. Peak Pilates strongly

recommends that the end user’s physical condition be evaluated prior to beginning any exercise program.

Note: Understanding each and every warning to the fullest is critical. If any of these warnings are unclear, ask for clariﬁcation from Peak Pilates representative.

Warranty

Peak Pilates warrants your purchase to be free of manufacturing defects. Please contact customer service or visit our website to view our

complete warranty policy.

1. Rotate the push-through bar back through the upright. Wrap the short black

strap attached to the middle eyebolt on the cross pole around the handle of the

push-through bar.

2. Re-attach the clip.

Attach one of the ﬂeece hanging straps to each of the upper

spanner poles “luggage tag style”.

1. Hold a strap so that it is centered over and perpendicular to the length

of a spanner pole. The black webbing material will be on one side of the

pole and the ﬂeece cover on the other.

2. Allow both ends to drop such that black webbing forms a loop below

the spanner pole.

3. Insert the ﬂeece cover through the loop formed by the black web and

pull down on the strap to tighten the knot.

Please do not hesitate to contact us with any questions:

1-800-925-3674 or [email protected]. We are here

to assist you in every way possible.

Installing the Springs

Push-through Spring

Push-through springs are similar to reformer springs in length and diameter, but

are distinguished by having closed loops at both ends. Using a safety link, attach

one end of a push-through spring to the second eyebolt from the end of one side

of the cross pole of the push-through pole system. Using a quick snap clip with

thumbscrew, attach the other end of the push-through spring to the corresponding

eyebolt on the arm of the push-through spring. For exercises that require the push-

through bar to be spring loaded from the bottom, using a safety link, attach one

end of the second push-through spring to an eyebolt on the leg of the cadillac table.

Using a quick snap clip with thumbscrew, attach the other end of the push-through

spring to the corresponding eyebolt located on the arm of the push-through bar.

Always use the safety chains with safety links when attaching the spring from the

bottom.

Be sure to slip the spring cover sleeve completely over the bottom push-through

spring to protect your mat from any abrasion when in contact with the spring.

Trapeze Springs and Trapeze Pad

The trapeze springs are the springs with the greatest force and are closed on one

end and open on the other. The coils of these springs are very difﬁcult to manually

separate. Before you install the springs, slip one of the spring covers over each.

These covers protect users from getting pinched when the springs are in use with the

trapeze.

Use double ended clips to attach the closed-loop end of the springs to the eyebolts in

the trapeze pad. Hook the open end of the springs through the eyebolts in the slider

bar. In most cases, users slide the trapeze assembly to one end or the other of the

cadillac to move it out of the way. Or, you can remove the trapeze pad and springs if

desired.

Push-through Bar Setup

The push-through pole system has two safety chains

WARNING: You must use the safety chains when the push-through springs are

attached to the push-through bar from the bottom. If you do not take this

precaution, the user can be seriously injured.

1. Using a safety link, attach a safety chain to the outermost eyebolt(s) on each end

of the push-through bar cross pole.

2. Attach a quick snap clip with thumbscrew to the other end of each chain.

3. When the chains are not in use, the quick snap clip should be fastened to its

respected cross pole eyebolt so it can hang freely in a loop.

4. The safety chains must be clipped to their respective eye bolts located on the top

of each arm of the push-through bar whenever the push-through spring is being used

from below.

TOOLS

• 3/16” Allen wrench (provided)

• 1/2” wrench - for Premier Cadi ONLY

• 1/2” socket wrench - for Premier Cadi ONLY

PARTS LIST

1. Push-through bar assembly

2. Roll down Poles (2)

3. Spanner poles (2)

4. Roll down cross pole

5. Trapeze slider

COMPONENTS

A. Foot loops (pair)

B. Sheepskin hanging straps (pair)

C. Adjustable wraparound table strap

D. Trapeze strap

E. Arm spring (2)

F. Leg spring (2)

G. Push-through spring (2)

H. Trapeze spring (2)

I. Spring sleeve (3)

J. Double ended clips (10)

K. Safety link with thumbscrew (4)

L. Quick snap clip with thumbscrew (2)

M. Safety chains (2)

N. Padded trapeze

O. Roll down bar

The spanner poles connect the two sets of upright poles. Both

the spanner poles and the ﬁttings on the ends of the cross poles

are marked in two ways (see accompanying ﬁgure): a) they are

marked to indicate which end of each spanner pole goes in to

which ﬁtting and b) how far the spanner pole should be inserted

into each ﬁtting.

1. Identify the spanner pole that is to be used on each side of the

Machine as well as its orientation by matching the markings found

on the spanner poles and cross pole ﬁttings (A – to – A or 1 – to

– 1; B – to – B or 2 – to – 2; and so on). When assembled, the

markings should face upward. [NOTE: if a 2nd person is available

to support the spanner poles, slide the trapeze assembly onto

both spanner poles and insert the proper end of each spanner into

its respective ﬁttings so that the black locking knob will end up

oriented toward the roll down upright poles. Now skip to step 8.]

2. Loosen the set screws used to retain the trapeze slider ﬁttings

to the trapeze cross bar. Slide the ﬁttings off of the bar. [NOTE:

The trapeze pipe and ﬁttings are marked like the spanner poles.]

3. Slide one slider ﬁtting onto each spanner pole such that the

black locking knob will end up oriented toward the roll down upright

poles. The proper end can be identiﬁed once the spanner pole

markings are matched against the indicators on the 3-way ﬁttings

on top of the poles (see step 1).

4.While standing on the cadillac’s mat, insert the proper end of

each spanner into its respective ﬁtting. Be sure that that markings

match.

Note: the push-through and roll-down pole systems will have to be

pushed slightly apart to be able to get both ends of the spanners

into their respective ﬁttings.

Caution: when spreading the pole systems to ﬁt the second

spanner pole, care must be taken to insure that the ﬁrst spanner

does not become disengaged from its ﬁttings. If it does, it could

fall and tear the cadillac upholstery. Temporarily tighten the ﬁrst

spanner to prevent this.

5. Slide both of the trapeze slider ﬁttings toward one end of the

machine. Orient one of the ﬁttings such that the black knob is

facing down. Insert one end of the trapeze cross bar into this ﬁtting

and slide it as far toward the outside of the machine as it will go

(one of the eyebolts will contact the edge of the ﬁtting).

6. Carefully disengage the opposite spanner (with the second slider

ﬁtting) from the 3-way ﬁtting on the adjacent pole assembly while

at the same time orienting the slider ﬁtting such that the black

knob is facing down. Slide the free end of the trapeze cross bar

into the slider ﬁtting and replace the spanner into its 3-way ﬁtting.

Caution: when disengaging or replacing the second spanner pole,

care must be taken to insure that the ﬁrst spanner does not

become disengaged from its ﬁttings. If it does, it could fall and

tear the cadillac upholstery. Temporarily tighten the ﬁrst spanner

to prevent this.

7. Center the trapeze cross bar between its two slider ﬁttings. Be

sure that the eyebolts are facing down and the indicators are up

and tighten the slider ﬁttings’ set screws.

8. Verify that all of the markings on the spanner poles and 3-way

ﬁttings are properly aligned. Tighten all fasteners including the

set screws as well as the nuts (Premier Cadillac only) used to

assemble the ﬁttings to the cadillac’s legs.

9. Verify that the trapeze assembly slides back and forth easily

without binding.

Installing the Push-through Pole Assembly

The push-through pole assembly comes pre-assembled. Before you install it to the head

of the cadillac frame, make sure that the allen screws are backed all the way out of the

frame’s ﬁttings and that there are no obstructions in the ﬁttings’ holes. Doing so prevents

the poles from being scratched. If your ceiling is less than 8 1/2’ high, tip the cadillac

table over on its side.

1. Slide the two push-through upright poles through the ﬁttings mounted on the back of

each table leg on the same side as the attached footstrap. [Note: the bottom ﬁtting on the

Premier Cadillac requres a 1/2” wrench. Do not tighten yet.] The open end of the 3-way

ﬁttings located at the top left and right corners of the assembly face toward the center of

the cadillac. You may need to gently jostle the pole system back and forth while inserting

it through the ﬁttings. The poles rest on the eyebolts located directly under the bottom

ﬁtting.

2. Do not tighten the allen screws in the ﬁttings at this time.

The roll-down upright pole system comes unassembled and consists of two upright poles

and a cross pole. If you have purchased the optional leg-spring slider bar, read below. To

install the roll-down upright poles, ﬁrst make sure that the allen screws are backed all

the way out of the ﬁttings located on the far side legs (see “Installing the push-through

pole assembly” above) and that there are no obstructions in the ﬁttings’ holes. Doing so

protects the poles from being scratched.

1. The roll-down upright poles are outﬁtted with 6 eyebolts each (4 on one side and 2 on

the other). Slide one pole through each pair of ﬁttings mounted to the back of each table

leg at the opposite end from the push-through bar. Make sure the poles are oriented so

that the side of the poles with the 4 eyebolts faces toward the push-through bar.

2. Insert the roll-down cross pole with its ﬁttings to the top of the roll down upright poles.

The cross pole eyebolts should face down.

3. Do not tighten the allen screws or 1/2” nuts [for Premier Cadi ONLY] in the ﬁttings at

this time.

If you ordered your cadillac with the optional leg spring slider bar, perform the

following steps:

1. Have an assistant hold the optional leg spring slider bar assembly such that its ﬁttings

are directly over the respective ﬁttings mounted to the back of each table leg at the end of

the table opposite the push-through bar. Make sure that the side of the slider bar with the

eyebolts faces the push-through bar.

2. Slide one of the upright poles through the end ﬁtting of the slider bar and then through

the two ﬁttings mounted on one of the table legs. Seat the upright pole against the eye

bolt located immediately below the bottom ﬁtting. Repeat with the second upright pole.

3. Slide the leg spring slider assembly approximately half way up the roll down upright

poles.

4. Insert the cross pole into the ﬁttings at the top of the roll down upright poles. Make sure

the eyebolts are facing down and the open ends of the 3-way ﬁttings face in.

5. Do not tighten the allen screws in the ﬁttings at this time.

Installing the Roll-Down Upright Poles

Peak Pilates Classic Cadillac Installation guide

Brand: Peak Pilates

Model: Classic Cadillac

Type: Installation guide

This manual is also suitable for

Download PDF

report

Peak Pilates Classic Cadillac Installation guide

This manual is also suitable for

Peak Pilates Classic Cadillac Installation guide

Related papers

Other documents