Extron Extender MK User manual

Type
User manual
1
IMPORTANT:
Go to www.extron.com for the complete
user guide,
installation instructions,
and
specifications bef
ore connecting the
pr
oduct to the po
wer source.
Extender Series • Setup Guide
ATTENTION: Installation and service must be performed by authorized personnel only. These products must be used with
UL Listed, grounded electrical boxes.
Step 1 — Disconnect Power
Turn all of the equipment off and disconnect the power cords from the power source.
Step 2 — Install the Wall Box
Select the installation location and install the electrical wall box, as shown at right.
NOTE: The Extron Extender AAP EX does not require a wall box if it is installed into an
Extron HSA 400 Series or HSA 800 Series surface access product.
Step 3 — Attach Cables
Attach the cables as shown in figure 1. below. For details on all connections, see the
installation instructions in the Extender Series User Guide. For the Extender AAP EX, install the
unit into the faceplate of an Extron HSA 400 Series or HSA 800 Series surface access product
before attaching the cables.
12 VDC
Power
To RGB
Video Equipment
Extender Series
12 VDC
Power
Gain
(Switch is on the lower circuit board.)
Maximum
Max. peaking
& gain
Medium – Mid-level
peaking & gain
Normal
Unity
gain
ww
w.e
x
tron.com
33-612-0
2
Rev. C
02 05
L
Audio
R
Sleeve (s)
Left Tip
Right Tip
Left Ring
Right Ring
12 VDC
Power
Sleeve
(s)
Left Tip
Right Tip
Left Ring
Right Ring
Audio
Unbalanced Output
Left Tip
NO Ground Here
Sleeve
(s)
Right Tip
NO Ground Here
Balanced Output
Sleeve
(s)
Left Tip
Right Tip
Left Ring
Right Ring
L
Audio
R
L
Audio
R
Do not tin the wires!
CAUTION
For unbalanced audio, connect the
sleeve(s) to the ground contact.
DO NOT connect the sleeve(s)
to the negative (-) contacts.
(5 mm) max.
Figure 1. Cable Connection Overview
NOTE: Horizontal sync = black. Vertical sync = yellow.
Installation
Cable
Cable Clamp
Wall Stud
Screws or
Nails
2
Extender Series • Setup Guide (Continued)
Step 4 — Mount AAPs
Mount all AAPs into faceplates with AAP openings, as in the example at right.
Mount Extender AAP models into wall plates or faceplates. — The Extender AAP or
ExtenderAAP EX and any other adapter plates must be attached to a device faceplate or AAP
wallplate and cabled before the device or wallplate is pretested or installed in a wall or furniture
1. Before any user-supplied cables are attached, insert the output BNC connectors and wires
of the Extender AAP or Extender AAP EX through the opening in the front of the
wallplate or device faceplate, as shown at right.
ATTENTION: Be careful not to damage connectors while placing the
Extender through the opening.
2. Insert the threaded standoffs of the AAP through the holes in the device
faceplate or AAP wallplate.
3. Using the provided #4-40 nuts and captive washers, secure the Extender
to the faceplate or wallplate (see figure 2).
Extron
AAP 102
EXTE
NDER
COMPUTER IN
AUDIO IN
RGB - 20"
HV - 18"
Connects to
AAP Cable
Front
Panel
Extron
HSA 822
Two Screws
Each Side
#4-40 Nut
w/ Captive
Washer
Installation Cable
Cable
Clamp
Screws or
Nails
Wall Stud
Extron
Extender AAP
Extron
AAP 102
#4-40 Nut w/
Captive
Washer
HSA 822
Cable
Extron
Extender AAP EX
COMPUTER IN
AUDIO
IN
Figure 2. Left: Mounting the Extender AAP or Extender AAP EX to a Device or Wallplate
Right: Mounting the ExtenderAAP EX to an HSA Faceplate
4. Repeat steps 1, 2, and 3 to mount other AAPs. Cover any openings in the faceplate with blank plates (provided).
5. Be sure to include the AAP connectors as part of the installation pretest before final installation of the faceplate.
6. For more detailed installation information, see the installation guide shipped with the faceplate or the HSA.
Extron
Extender AKM MAAP
Line Driver
EXTENDER AKM MAAP
COMPUTER IN
AUDIO IN
#4 - 40 Screws
Extron
AAP 102
AAP 102
Rotate to avoid
breaking the
power connector
on the bottom
board.
EXTENDER
COMPUTER IN
AUDIO IN
3
Step 5 — Connect Power
Connect power and turn the equipment on.
Step 6 — Test and Adjust the System
1. Test the system and set the gain switch,
shown at right.
2. Ensure that all devices receive power.
3. Check and adjust cabling and gain as needed.
Step 7 — Disconnect Power
Disconnect power from all the devices.
Step 8 — Mount the Extender
Mount the line driver into the electrical box or the body of the HSA. See the ExtenderAKMMAAP Installation Guide, or the
appropriate HSA Series user guide, as needed.
Step 9 — Install the Faceplate (Extender D)
For the Extender D, install the decorator-style faceplate.
Step 10 — Restore Power
Restore power to the devices.
Maximum
Max.
peaking
and gain
Medium – Mid-level
peaking and gain
Normal
Unity
gain
Maximum
Max. peaking
and gain
Medium – Mid-level
peaking and gain
Normal
Unity
gain
Circuit
board
Faceplate
Maximum
Max. peaking
and gain
Medium
Mid-level
peaking
and gain
Normal
Unity gain
Extender
D
(viewed
from front)
Extender WM
Extender WM AAP
(viewed from side)
Extender MK, AKM,
AUS, AAP Models
(viewed from rear)
4
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Australia
+61.8.8113.6800
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2017 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Extender Series • Setup Guide (Continued)
Contact Information
68-552- 50
Rev. B
05 17
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Extron Extender MK User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI