< Totalizer
(trailing digits)
INCREASE
SELECT
SELECT
SELECT
< Time of Day Adjust-
SELECT
IN-
< Password
If system is Locked, a pass-
word will need to be entered.
SELECT
LectroCount LCR
LectroCount LCR-
-II
II
™
Menu Map
Menu Map
LCR-II Selector Switch Plate
< Flow Rate
F 70
.
0
< Delivery Total
200
.
0
< Temperature
38
.
7 F
RUN
RUN Position
Position
SELECT
SELECT
SELECT
< Delivery Total
200
.
0
STOP
STOP Position
Position
SELECT
SELECT
< Preset Amount
INCREASE
INCREASE
INCREASE
INCREASE
00200
.
0
< Product No.
PROD 1
SELECT
PROD 2
PROD 4
PROD 3
o
INCREASE
< Time of Day
PRINT
PRINT Position
Position
< Delivery Total
200
.
0
INCREASE
INCREASE
INCREASE
INCREASE
k98765
PROD 1
SELECT
PROD 2
PROD 4
PROD 3
L5432
.
0
P12345
SELECT
11
:
30
:
00
12
:
30
:
00
< 10 Digit Totalizer
(leading digits)
< Totalizer
(trailing digits)
INCREASE
PROCEDURE FOR MAKING A PRESET DELIVERY
PROCEDURE FOR MAKING A PRESET DELIVERY
1. Turn the Selector Switch to the STOP position.
2. Press the SELECT button. The display will show Prod #.
3. Press INCREASE to select the product desired for delivery.
4. Press SELECT when the correct Prod # is displayed. This will advance to
the preset display.
5. The left most digit in the display will be flashing. Press INCREASE to set
the value of the first digit. When the value is chosen, press SELECT. The
next digit to the right will flash. If the digit does not need to be changed,
press SELECT to move one digit to the right.
6. Press INCREASE to change the value of the second digit. When the value
is chosen, press SELECT.
7. Continue in this manner until all digit positions have been selected. After the
last digit is selected, the display will return to the first screen, which is the
Delivery Total. Or, switch to RUN when the desired amount is shown.
8. Turn the Selector Switch to RUN. DO NOT OPEN THE HOSE NOZZLE.
When the display stops counting, turn the Selector Switch back to STOP.
This step is necessary to allow for hose stuffing. If less than 1 Gallon was
recorded, the display will reset to 0 and no ticket will be printed.
9. Turn the Selector Switch to RUN. The display will reset and the hose nozzle
should now be opened to start the delivery. When the preset has been
reached, the valve will close.
10. Turn the Selector Switch to the PRINT position to print out a delivery ticket.
PROCEDURE FOR PRINTING A DIAGNOSTIC TICKET
PROCEDURE FOR PRINTING A DIAGNOSTIC TICKET
1. Put a blank ticket in the Epson Printer.
2. Turn the Selector Switch to SHIFT PRINT for less than 2 seconds.
3. Turn the Selector Switch back to PRINT and a Diagnostic ticket will be
printed.
PROCEDURE FOR PRINTING A SHIFT TICKET
PROCEDURE FOR PRINTING A SHIFT TICKET
1. Put a blank ticket in the Epson Printer.
2. Turn the Selector Switch to SHIFT PRINT for more than 2 seconds.
SHIFT PRINT
SHIFT PRINT Position
Position
SELECT
< Delivery Total
200
.
0
INCREASE
INCREASE
INCREASE
INCREASE
PROD 1
SELECT
PROD 2
PROD 4
PROD 3
L5432
.
0
< 10 Digit Total-
izer
SELECT
k98765
< k-Factor
SELECT
SELECT
SELECT
< Temperature
< Flow Rate
098
.
023
INCREASE
INCREASE
INCREASE
INCREASE
F 70
.
0
PROD 1
SELECT
PROD 2
PROD 4
PROD 3
27
.
2 F
< k-Factor
102
.
965
CALIBRATION
CALIBRATION Position
Position
INCREASE
“If Delivery is
Active”
o
INCREASE
/
