200W DMX512 LED Driver(constant voltage) 70230016
Function introduction
Important: Read All Instructions Prior to Installation
AC 100-277V
power input
Common Anode Output(+)
Common Anode Output(+)
CH 1:R/WW output(-)
CH 2:G/CW output(-)
CH 3:B/WW output(-)
CH 4:W/CW output(-)
DMX512 signal input
Digital display
MTBF
Others 185800H, MIL-HDBK-217F @ 230VAC full load and 25℃
ambient temperature
Over Current Yes, recovers automatically after fault condition is removed
Over Temperature
Protection
Yes, recovers automatically after fault condition is removed
Max. Case Temp. 85℃ (Ta=" ")45℃
Working Humidity
Working Temp.
Environment
-20 ~ +45℃ ℃
10% ~ 95% RH non-condensing
Storage Temp.
& Humidity -40 ~ +80 , 10% ~ 95% RH℃ ℃
Withstand Voltage I/P-O/P: 3.75KVAC
Isolation Resistance
Safety Standards
Safety &
EMC I/P-O/P: 100M Ohms / 500VDC / 25℃ / 70% RH
EMC Emission EN55015, EN61000-3-2, EN61000-3-3
EMC Immunity EN61547, EN61000-4-2,3,4,5,6,8,11, surge immunity Line-Line 1KV
Product Data
Voltage Range 100-277V AC
Power Factor (Typ.)
Efficiency (Typ.)
Frequency Range 50/60Hz
Input
Rated Power max. 200W
Output Max. Current
DC Voltage
Max. 8.3A/ch,
ch1+ch2+ch3+ch4=16.6A
24V DC12V DC
Max. 4.1A/ch,
ch1+ch2+ch3+ch4=8.4A
LED Channel 4
Voltage Tolerance ±1%
> 0.98 @ 230VAC
Total Harmonic
Distortion
AC Current (Typ.)
93% @ 230VAC full load
THD ≤ 15% (@ full load / 230VAC)
2.3A @ 100VAC, 1A @ 230VAC, 0.9A@277VAC
Leakage Current
Standby Power
Consumption
< 0.5mA /230VAC
< 1W
Control
Dimming Interface
Dimming Range
Dimming Method
0.1%-100%
DMX
Pulse Width Modulation
Dimming Curve Linear, Logarithmic
• Dimmable LED driver with rectangle metal case
• 4 channels 12/24VDC constant voltage output, to control single color, CCT, RGB/RGBW LED lighting
• Class 1 power supply, full isolated metal case
• Built-in two-stage active PFC function
• PF > 0.98, Efficiency > 93%
• Low standby power < 1W
• Built-in DMX dimming interface
• PWM digital dimming, logarithmic or linear dimming curve selectable
• Input protocols: DMX512(2008), DMX512-A
• Compliant with Safety Extra Low Voltage standard
• Over load, over temperature protection
• IP20 rating, suitable for indoor LED lighting applications
• 5 years warranty
• DO NOT install with power applied to the device.
• DO NOT expose the device to moisture.
Safety & Warnings
1.1 Press and hold down button “1” until numeric digital display flashes, then
release the button.
1.2 Click any of the 3 buttons once to select a digit, click again to change the digit
until the desired DMX address appears. Click button “1” to set “hundreds” position,
button “2” to set “tens” position and button “3” to set “units” position.
1.3 Then press and hold down any of the 3 buttons until the numeric digital display
stops flashing to confirm the setting.
button“1”
button“2”
button“3”
Operation
1. Set DMX Address Manually Via Buttons
UL8750, CAN/CSA C22.2 No. 250.13-14,
ENEC EN61347-1, EN61347-2-13 approved
L
N
AC IN PUT
FG
05 09 0 9
4-
GND
D+
D-
D+
D-
1-
2-
3-
LED O UTPUT
DMX 512 SIG NAL
200W DMX512 Dimmable Driver (AWG2 0-14)
(0.2 4-0.2 8in)
SEC:
Output Voltage=2 4VDC
Irated=1x4.16A /2x4.16A/
3x2.75A/4x2.0 8A
Prated=1x100W /2x100W/
3x66W/4x50W
INPUT:
100-240V~ 2.3A 50/ 60Hz
277V~ 0.806A 50/60 Hz
(277V~for North Am erica only)
NC=None c onnect Su itable for Damp Locati ons (CONV IENT AUX E MPLACEM ENTS HUMI DES)
E4935 67
ta
λ>0.95@230VAC:
85
45
(AWG1 8-14)
(0.5 5-0.8 6in)
NC
NC
Inrush Current (Typ.) COLD START Max. 65A at 230VAC
emc
300MHz
3.1 Press and hold down both button “1” and button “3” until digital display flashes
with “P_c”, release the buttons.
3.2 “P” means PWM frequency, 2 PWM frequencies are available, click button “1”
to choose “1” or “2”, “1” stands for 1500Hz and “2” stands for 200Hz.
3.3 “c” means dimming options, 2 options are available, click button “3” to choose
“1” or “2”, “1” stands for logarithmic dimming and “2” stands for linear dimming.
3.4 Press and hold down any of the 3 buttons until digital display stops flashing to
confirm setting. Factory default setting is 1-2 which means 1500Hz PWM
frequency with linear dimming.
3. Set Output PWM Frequency
2.1 Press and hold down both button “2” and button “3” until the digital display
flashes with “cH”, release the buttons.
2.2 Click button “1” to choose 1cH, 2cH, 3cH, 4cH, which means total 1, 2, 3, 4
DMX channels. Then press and hold down any of the 3 buttons until digital display
stops flashing to confirm the setting. Factory default setting is 4 channels output.
NOTE:
For example, when we set address as 001.
When select 1cH, all 4 channels will be the same address 001.
When select 2cH, channel 1&3 will be address 001, channel 2&4 will be address 002.
When select 3cH, channel 1 will be address 001, channel 2 will be address 002, channel 3 will be address
003, and channel 4 will be address 001.
When select 4cH, channel 1, 2, 3, 4 will be address 001, 002, 003, 004 respectively.
2. Set DMX Channel Quantity
Wiring diagram
Max. 10 0W/CH, tot al powe r of 4 ch annel s can not exce ed 200W
V+ V+
V- V-
AC 100-277V input
DMX512
Master
V+ V+
WW- WW-
CW- CW-
AC 100-277V input
AC 100-277V input
Max. 10 0W/CH, tot al powe r of 4 ch annel s can not exce ed 200W
V+ V+
R- R-
G- G-
B- B-
W- W- MAX 200 W RGBW LED
L
N
AC INP UT
FG
05 09 09
4-
GND
D+
D-
D+
D-
1-
2-
3-
LED OU TPUT
DMX5 12 SIGN AL
200W DM X512 Di mmable Dri ver (AWG20-14)
(0.24-0.28in)
SEC :
Out put Volt age=2 4VDC
Irat ed=1 x4.1 6A/2 x4.1 6A/
3x2 .75A/ 4x2.0 8A
Pra ted= 1x10 0W/2 x100 W/
3x6 6W/4x 50W
INP UT:
100 -240V ~ 2.3A 50/ 60Hz
277 V~ 0.80 6A 50/60 Hz
(27 7V~fo r North Am erica o nly)
NC= None co nnect S uitab le for Da mp Loca tions ( CONVI ENT AUX EM PLACE MENTS H UMIDE S)
E49 3567
ta
λ>0.9 5@23 0VAC:
85
45
(AWG18-14)
(0.55-0.86in)
NC
NC
L
N
AC INP UT
FG
05 09 09
4-
GND
D+
D-
D+
D-
1-
2-
3-
LED OU TPUT
DMX5 12 SIGN AL
200W DM X512 Di mmable Dri ver (AWG20-14)
(0.24-0.28in)
SEC :
Out put Volt age=2 4VDC
Irat ed=1 x4.1 6A/2 x4.1 6A/
3x2 .75A/ 4x2.0 8A
Pra ted= 1x10 0W/2 x100 W/
3x6 6W/4x 50W
INP UT:
100 -240V ~ 2.3A 50/ 60Hz
277 V~ 0.80 6A 50/60 Hz
(27 7V~fo r North Am erica o nly)
NC= None co nnect S uitab le for Da mp Loca tions ( CONVI ENT AUX EM PLACE MENTS H UMIDE S)
E49 3567
ta
λ>0.9 5@23 0VAC:
85
45
(AWG18-14)
(0.55-0.86in)
NC
NC
L
N
AC INP UT
FG
05 09 09
4-
GND
D+
D-
D+
D-
1-
2-
3-
LED OU TPUT
DMX5 12 SIGN AL
200W DM X512 Di mmable Dri ver (AWG20-14)
(0.24-0.28in)
SEC :
Out put Volt age=2 4VDC
Irat ed=1 x4.1 6A/2 x4.1 6A/
3x2 .75A/ 4x2.0 8A
Pra ted= 1x10 0W/2 x100 W/
3x6 6W/4x 50W
INP UT:
100 -240V ~ 2.3A 50/ 60Hz
277 V~ 0.80 6A 50/60 Hz
(27 7V~fo r North Am erica o nly)
NC= None co nnect S uitab le for Da mp Loca tions ( CONVI ENT AUX EM PLACE MENTS H UMIDE S)
E49 3567
ta
λ>0.9 5@23 0VAC:
85
45
(AWG18-14)
(0.55-0.86in)
NC
NC
Product Dimension
330mm
79mm
39mm
261.7mm
270mm
62mm
79mm
39mm
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sunricher SRPC-2305-24-200CVF User manual
-
-
-
-
-
-
-
-
-
Other documents
-
SKYDANCE V4-L User manual
-
-
-
-
LED WORLD LIGHTING H-2102B User guide
-
Ltech SE-40-300-1050-W2M Owner's manual
-
LED WORLD H-DMX2108A-5M-3 Owner's manual
-
STUDIO DUE CLEVER SPOT RGBW User manual
-
Q-tran Q-TRAN QTM-eLED plus 0-10V-AWN LED Power Supply Owner's manual
-
SuperLightingLED DL User manual
