EV4-X
Page 1
2023.9
Mechanical Structures and Installations
User Manual Ver 1.0.5
Technical Parameters
Input voltage
Input and Output Safety and EMC
EMC standard (EMC)
Certication CE,EMC,LVD
Safety standard(LVD)
Input current
Output voltage
Output current Operation temperature
Environment
Ta: -30
O
C ~ +55
O
C
Case temperature (Max.)
Tc: +85
O
C
Gross weight
Size
Package
L120 x W90 x H30mm
0.287kgIP20 IP rating
Input signal
Output type
Output power
Constant voltage
12-24VDC
32.5A
PWM
Warranty and Protection
5 years
Protection Reverse polarity
Warranty ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
EN 62368-1:2020+A11:2020
107.00 mm
75.00 mm
24.50 mm
75.00 mm
4 x (96-192)W
4 x (12-24)VDC
4CH,8A/CH
4 Channel Constant Voltage Power Repeater
● 12-24V constant voltage power repeater.
● 4 channel, 8A per channel.
● To receive PWM signal control.
● Power repeater in series or in parallel to expand output unlimitedly.
● Apply to single color, dual color,
RGB or RGBW constant voltage LED strip or module.
CH1/R LED output -
LED output +
Power input -
Power input +
Installation rack
Installation rack
CH2/G LED output -
CH3/B LED output -
CH4/W LED output -
CH2/G PWM input -
CH3/B PWM input -
CH4/W PWM input -
Power indicator
POW E R
I N P U T
PWM S I G N A L
V+ R G B W
-
++
W
+ + +
-
CH1/R PWM input -
PWM input +
LVD
Power Repeater
Wiring Diagram
Page 2
2023.9
User Manual Ver 1.0.5
Malfunctions analysis & troubleshooting
1. The product shall be installed and serviced by a qualified person.
2. This product is non-waterproof. Please avoid the sun and rain.
3. Good heat dissipation will prolong the working life of the controller,Please ensure good ventilation.
4. Please check if the output voltage of any power supplies used comply with the working voltage of the product.
5. Ensure all wire connections and polarities are correct and secure before applying power to avoid any damages to the LED lights.
6. If a fault occurs please return the product to your supplier. Do not attempt to fix this product by yourself.
Safety & Warnings
Power Supply
12-24VDC
Constant Voltage
PO W ER
W
RGBW LED strip
Power Supply
12-24VDC
Constant Voltage
AC100-240V
Power Supply
12-24VDC
Constant Voltage
AC100-240V
AC100-240V
I NP U T
PWM SI G NAL
V+ R G B W
-
++
W
+ + +
-
EV4-X
PO W ER
I NP U T
PWM SI G NAL
V+ R G B W
-
++
W
+ + +
-
EV4-X
VP
+
-
OU T PUT
+
IN P UT
12-24 VD C
+
+
+
W
W4 +
+
+
W
RGBW LED strip
Wrong color 1. Wrong connection of R/G/B/W wires.
Malfunctions
Causes
Uneven intensity
between front and
rear,with voltage drop
1. Output cable is too long.
2. Wire diameter is too small.
3. Overload beyond power supply capability.
4. Overload beyond controller capability.
No light
1. Reconnect R/G/B/W wires.
Troubleshooting
1. Reduce cable or loop supply.
2. Change wider wire.
3. Replace higher power supply.
4. Add power repeater.
1. Check the power.
2. Check the connection.
1.No power.
2.Wrong connection or insecure.
/
