Asante Technologies IntraCore IC3524-2T User manual

Brand: Asante Technologies

Model: IntraCore IC3524-2T

Category: Network switches

Type: User manual

This manual is also suitable for

IntraCore

™

3500 Series

Gigabit Ethernet Switches

User’s Manual

Quick Start Guide

Follow these steps to install your IntraCore switch:

1. Open the box and check the contents. See Chapter 1.1 Package Contents for a complete list of the

items included with your IntraCore switch.

2. Install the switch in an equipment or wall rack, or prepare it for desktop placement.

3. Connect the power cord to the unit and to an appropriate power source.

4. Connect network devices to the switch.

5. Refer to Chapters 3-5 to configure the IntraCore for configuration and management capabilities.

For more information on installing the switch, please refer to Chapter 2 Installation and Setup.

IC3524, IC3524-2T and IC3524-2G Models

IC3548-2GT

IntraCore 3500 Series

Gigabit Ethernet Switches

User’s Manual

Asanté Technologies, Inc.

821 Fox Lane

San Jose, CA 95131

USA

SALES

800-662-9686 Home/Office Solutions

800-303-9121 Enterprise Solutions

408-435-8388

TECHNICAL SUPPORT

801-566-8991: Worldwide

801-303-3787: FAX

www.asante.com

support@asante.com

product design, or design concept may be copied or reproduced in whole or in part by any means without the express

written consent of Asanté Technologies, Inc. Asanté is a registered trademark and the Asanté logo, IntraCore, IntraCare

and AsantéCare are trademarks of Asanté Technologies, Inc. All other brand names or product names are trademarks or

registered trademarks of their respective holders. All features and specifications are subject to change without prior

notice.

Rev. A

Table of Contents

Quick Start Guide 2

Chapter 1. Introduction 6

1.1 Package Contents 6

1.2 LEDs 7

1.3 Front and Back Panel Descriptions 9

1.4 Management and Configuration 10

Chapter 2. Hardware Installation and Setup 12

2.1 Installation Overview 12

2.2 Installation into an Equipment Rack 13

2.3 GBIC Interfaces 14

2.4 Installing Optional Hardware Modules 15

2.5 Connecting Power 15

2.6 Connecting to the Network 16

2.7 Setup 17

2.8 Changing the Password 18

2.9 IP Assignment 19

2.10 SNMP Management 19

2.11 Using the Stacking Feature 20

Chapter 3. Configuration 22

3.1 General Information 23

3.2 Configuration Menu 23

3.3 System Administration Configuration 24

3.4 System IP Configuration 25

3.5 Bootstrap Configuration 25

3.6 SNMP Configuration 26

3.7 Port Configuration 28

3.8 Advanced Port Configuration 31

3.9 Unicast Forwarding Database Configuration 33

3.10 Security Management 35

3.11 VLAN Management 35

3.12 IP Multicast Traffic Management 35

3.13 Port Mirroring Configuration 35

3.14 File Up/Downloading Configuration 36

3.15 System Reset Configuration 38

3.16 System Log 39

3.17 User Interface Configuration 40

3.18 System Utility 42

3.19 Viewing Statistics 43

Chapter 4. Advanced Management 44

4.1 Spanning Tree Protocol 44

4.2 SNMP and RMON Management 46

4.3 Security Management 46

4.4 VLAN Management 50

4.5 IP Multicast Traffic Management 55

Chapter 5. Web-Based Management 58

5.1 Front Panel Button 59

5.2 Genl Info (General Information) Button 59

5.3 Statistics Button 60

5.4 Port Config (Port Configuration) Button 61

5.5 Span Tree (Spanning Tree) Button 62

5.6 SNMP Button 63

5.7 Addr (Address) Table Button 63

5.8 VLAN Button 64

5.9 Security Button 68

5.10 Duplicate IP Button 69

Chapter 6. SNMP Management 70

6.1 SNMP Management Operations 70

6.2 The SNMP Protocol 70

6.3 Community Name and Security 71

6.4 The MIB Tree 71

Chapter 7. Switching Concepts 73

7.1 VLANs 73

7.2 Spanning Tree Protocol 74

7.3 Full Duplex, Flow Control and Auto-negotiation 75

Appendix A. Troubleshooting 77

Appendix B. Features and Specifications 78

B.1 Features 78

B.2 Specifications 78

Appendix C. FCC Compliance and Warranty Statements 80

Appendix D. Console Port Pin Outs 82

Appendix E. Online Warranty Registration 83

Appendix F. BootP Configuration 84

Chapter 1. Introduction

Thank you for purchasing the Asanté IntraCore 3500 Series Gigabit switch. The IntraCore 3500 series

include 24- and 48-port 10/100 managed switches with a variety of hardware and software options.

The IntraCore 3524 is a 24-port 10/100 managed switch with several optional hardware modules. Hardware

expansion slots (two Type IC35) can accept a wide range of Gigabit and 10/100 Mbps media modules:

• 10/100/1000BaseT

• 1000BaseX GBIC

• 1000BaseSX

• 100BaseMMFX

• 100BaseSMFX

The IntraCore 3548-2GT is a 48-port 10/100 managed switch with integrated 10/100/1000BaseT Gigabit

Ethernet ports and 1000BaseX GBIC expansion ports.

See the table below for a description of the 3500 series models that are available.

Model

10/100

Ports

Optional Media

Modules

Description

IC 3524 Base

Two IC35 slots

available

Managed 24-port 10/100 switch;

base

IC 3524-2G

24 Two 1000BaseX

GBIC slots

Integrated 1000BaseX GBIC

slots

IC 3524-2T

Two 10/100/1000

BaseT ports

Integrated copper Gigabit ports

IC 3548-2GT

48 Managed 48-port 10/100 switch

with two integrated GBIC slots

or two integrated

10/100/1000BaseT Gigabit

Ethernet ports

Table 1-1 3500 Models

The system can operate as a stand-alone network or be used in combination with other IntraCore series

switches in the backbone.

1.1 Package Contents

The following items are included in your package:

•

Switch

•

AC power cord

•

Rack mount brackets with screws

•

Rubber feet

•

Reference Guide

•

Getting Started Guide

•

User’s Manual (this document, on CD-ROM)

•

IntraCore 3500 CD-ROM

Contact your dealer immediately if any of these items are missing.

1.2 LEDs

The system’s LED display allows you to monitor the status of your switch. Refer to the sections below for

LED information specific to your switch’s model.

1.2.1 IC3524 Models

The IntraCore 3524 model switches have two LED indicators for each of the 24 10/100 ports, and three LED

indicators for both of the optional Gigabit ports. See Tables 1-2 and 1-3 below for a complete LED

description.

Port #

LED

Color

Description

N/A

Power/System

Green

Off

Power is on

Power is off

1-24(10/100)

10/100 Link

Solid Green

Solid Amber

Off

A valid 100 Mbps link has

been established

A valid 10Mbps has been

established

No link has been established

1-24(10/100)

Duplex

Solid Green

Solid Amber

Full Duplex

Half Duplex

Table 1-2 IC3524 Models-- Ports 1-24

Port #

LED

Color

Description

25, 26

Gigabit

(speed)

Solid Green

Off

A valid 1000Mbps link has

been established

No link has been established,

or link is at 10/100Mbps rate

25, 26

10/100 Link

Solid Green

Solid Amber

Off

A valid 100Mbps link has

been established

A valid 10Mbps link has been

established

No 10/100 link has been

established

25, 26

Duplex

Solid Green

Solid Amber

Full Duplex

Half Duplex

Table 1-3 IC3524 Models--Ports 25 & 26

1.2.2 IC3548-2GT

The IntraCore 3548-2GT switch has two LED status indicators for each of the 48 10/100 ports and the 2

Gigabit ports. Using the Mode button on the lower left of the front panel allows the user to convert between

Link/Activity status and Duplex status displays. See the tables below for more information on the LED

functions of the 3548.

Table 1-4 IC3548 Model--Ports 1-48

Port #

LED

Color

Description

N/A

Power/System

Green

Off

Power is on

Power is off

1-48(10/100)

Link/Activity

Solid Green

Blinking Green

Solid Amber

Blinking Amber

Off

A valid 100 Mbps link has

been established

Data transfer at 100Mbps

A valid 10Mbps has been

established

Data transfer at 10Mbps

No link has been established

1-48(10/100)

Duplex

Solid Green

Solid Amber

Blinking Amber

Off

Full Duplex

Half-Duplex

The switch is operating in

half-duplex

No full-duplex link has been

established, or no collisions

are occurring on the port

when operating at half-duplex

Port #

LED

Color

Description

Gigabit Ports

#49, 50

Link/Activity

Solid Green

Blinking Green

Solid Amber

Blinking Amber

Off

A valid 1000Mbps link has been

established

Data transfer at 1000Mbps

A 10/100Mbps link has been

established

Data transfer at 10/100Mbps

No Gigabit link has been

established

Gigabit Ports

#49, 50

Duplex

Solid Green

Solid Amber

Blinking Amber

Off

Full Duplex

Half Duplex

The switch is operating in half-

duplex

No full-duplex link has been

established, or no collisions are

occurring on the port when

operating at half-duplex

Table 1-5 IC3548 Model—Ports 49 & 50

1.3 Front and Back Panel Descriptions

Refer to the following sections for detailed descriptions of the front and back panels of the IntraCore 3500

series switches.

1.3.1 IC3524 Models

From left to right, the front panel contains the following: Power and port LEDs; 24 10/100 ports; 2 optional

module slots; and a console port.

The switch is field upgradeable for use with 100BaseeFX, 1000BaseSX, 1000BaseX GBIC or

10/100/1000BaseT modules.

The back panel (not shown) has only the AC socket.

1.3.2 IC3548-2GT

From the left to the right, the 3548 switch’s front panel contains the power LED and 2 exchanging LEDs; a

push button display mode converter; 48 10/100 ports, each with its own indicator light; and 2 Gigabit ports

(capable of using either the GBIC expansion ports [for fiber and copper GBICs] OR the 10/100/1000BaseT

Gigabit Ethernet ports), each with its own indicator light.

From left to right, the back panel (shown below) contains: a console port; a 12V DC jack for an external

power supply (IC35-RPS12, US part number 99-00777-01, sold separately); an AC socket (for primary

power) and a power switch.

1.4 Management and Configuration

There are three different methods by which a user can manage the switch: web, console/telnet, or with

SNMP software. You may prefer using a web browser to be able to configure the switch from any local or

remote computer, via the network, or you may wish to use a console for out-of-band management. SNMP is

an advanced management application, and is mostly automatic, giving you the information without having to

go through an interface step by step (Note: The switch is shipped with BootP support. See Appendix F for

more information on setting up BootP).

Table 1-4 Out-of-Band and In-Band Management

Method

Type

Description

Console

Out-of-Band

Management

Local connection to the switch via the

console port

Telnet

In-Band

Management

Remote connection over the network to

the switch via the telnet session

HTTP Server

In-Band

Management

Remote connection over the network to

the switch via a Web browser

SNMP-Based

Network

Management

Software

In-Band

Management

Remote connection over the network to

the switch via any SNMP-based network

management application

1.4.1 Console Interface

Users can access the switch in a more traditional way by connecting a PC or terminal to the console port or

by telnet across the network. The menus are organized in a manner similar to the web-based interface. A

detailed description can be found in Chapter 3 Configuration. Users must use a console connection to form

a stack (multiple units sharing one IP address). The stacking feature is available on the IC3524 models,

versions 1.1 or higher. See Chapter 2.11 Using the Stacking Feature for more details.

1.4.2 Web-Based Interface

With Internet access, users can link directly to the local switch’s home page. Users can configure the switch,

monitor the LED panel, and display statistics graphically. A detailed description can be found in Chapter 5.

Web-Based Interface.

1.4.3 SNMP Management

Since the switch supports SNMP, users can manage the switch with an SNMP-compatible management

station running platforms such as HP OpenView. It also supports a comprehensive set of MIB extensions

along with MIB II, Ethernet MIB, the 802.1D bridge MIB, and 4 groups of RMON. Please see Chapter 3, or

Chapter 6. SNMP Management for more information.

Chapter 2. Hardware Installation and Setup

The following guidelines will help you to easily install the switch, and to ensure that it has the proper power

supply and environment.

2.1 Installation Overview

Follow these steps to install your IntraCore switch:

1. Open the box and check the contents. See Chapter 1.1 Package Contents for a complete list of the

items included with your IntraCore switch.

2. Install the switch in an equipment or wall rack, or prepare it for desktop placement.

3. Connect the power cord to the unit and to an appropriate power source.

4. Connect network devices to the switch.

See the sections below for more detailed installation instructions.

2.1.1 Safety Overview

The following information provides safety guidelines to ensure your safety and to protect the switch

from damage.

Note: This information is intended as a guideline, and may not include every possible hazard to

which you may be exposed. Use caution when installing this switch.

•

Only trained and qualified personnel should be allowed to install or replace this equipment.

•

Always use caution when lifting heavy equipment

•

Keep the unit clean

•

Keep tools and components off the floor and away from foot traffic

•

Avoid wearing rings or chains (or other jewelry) that could get caught in the switch. Metal objects

can heat up and cause serious injury to persons and damage to the equipment. Avoid wearing

loose clothing (i.e. ties or loose sleeves) when working around the switch

When working with electricity, follow these guidelines:

•

Disconnect all external cables before installing or removing the cover

•

Do not work alone when working with electricity

•

Always check that the cord has been disconnected from the outlet before performing hardware

configuration

•

Do not tamper with the equipment. Doing so could void your warranty

•

Examine your work area for potential hazards (I.e. wet floors, ungrounded cables, etc.)

2.1.2 Recommended Installation Tools

You will need the following tools and equipment (not included) to install the switch into an equipment rack:

•

Flat head screwdriver

•

Phillips head screwdriver

•

Antistatic mat or foam

2.1.3 Power Requirements

The electrical outlet should be located near the switch and be easily accessible. It must also be properly

grounded.

Make sure the power source adheres to the following guidelines:

•

Power: Auto Switching 110/240 VAC

•

Frequency range: 50/60 Hz

•

Maximum Input AC Current: 1.0A at 115 VAC full load

2.1.4 Environmental Requirements

The switch must be installed in a clean, dry, dust-free area with adequate air circulation to maintain the

following environmental limits:

•

Operating Temperature: 0° to 40° C (32° to 104° F)

•

Storage Temperature: -20° to 70° C (-4° to 158° F)

•

Relative Humidity: 10% to 90% non-condensing

•

Storage Relative Humidity: 10% to 95% non-condensing

Avoid direct sunlight, heat sources, or areas with high levels

of electromagnetic interference.

2.1.5 Cooling and Airflow

The IntraCore 3500 series switches use internal fans for air-cooling. Do not restrict airflow by

covering or obstructing air vents on the sides of the switch.

2.2 Installation into an Equipment Rack

To install the unit in an equipment rack, use the following procedure:

Important! Before continuing, disconnect all cables from the unit.

1. Place the switch on a flat, stable surface.

2. Locate a rack-mounting bracket (supplied) and place it over the mounting

holes on one side of the unit.

3. Use the screws (supplied) to secure the bracket (with a Phillips screwdriver).

4. Repeat the two previous steps on the other side of the unit.

5. Place the switch in the equipment rack.

6. Secure the switch by securing its mounting brackets onto the equipment rack

with the appropriate screws (supplied).

Important!

Make sure the unit is supported until all the mounting screws for each bracket are secured to the

equipment rack. Failure to do so could cause the unit to fall, which may result in personal injury or damage

to the unit.

2.2.1 Equipment Rack Guidelines

Use the following guidelines to ensure that the switch will fit safely within the equipment rack:

•

Size: 17.25 x 10.0 x 1.8 inches (423 x 245 x 39 mm)

•

Ventilation: Ensure that the rack is installed in a room where the temperature remains below 40° C

(104° F). Be sure that there are no obstructions, such as other equipment or cables, blocking

airflow to or from the vents of the switch

•

Clearance: In addition to providing clearance for ventilation, ensure that there is adequate

clearance for servicing the switch from the front

2.3 GBIC Interfaces

The GBIC Interface is the industry standard for Gigabit Ethernet Interfaces. Some of the benefits of GBIC

include reducing the components needed in your “spares” inventory, a wide variety of manufacturers with

cross-vendor compatibility and competitive prices.

Instructions for installing, removing, and maintaining GBIC modules are provided in following sections.

Model Part Number Standard Media

GBIC 1000SX 99-00549-01 1000BaseSX Multi-mode fiber

GBIC 1000LX 99-00550-01 1000BaseLX Single mode fiber

GBIC 1000T 99-00673-01 1000BaseT Category 5 UTP copper

GBIC 1000TP 99-00647-07 1000BaseT Category 5 UTP copper

Table 2-1 GBIC Modules by Asanté

2.3.1 Installing a GBIC

GBICs are hot swappable. This means that they can be inserted and removed while the unit is powered on.

However, you should allow 40 – 60 seconds for the switch to recognize the module when it has been

installed while the unit is on.

1. Wearing an ESD (electro-static discharge) wrist strap, remove the GBIC module from its protective

packaging.

2. Verify that the GBIC is the correct type for your network (see the table above).

3. Grip the sides of the GBIC with your thumb and forefinger, then insert the GBIC into the slot on the

face of the switch.

4. Slide the GBIC into the slot until you hear or feel a click. The click indicates that the GBIC is locked

into the slot.

5. GBIC 1000SX and GBIC 1000LX modules: Remove the rubber plugs from the end of the GBIC

module. Save them for future use.

6. Attach the appropriate cable.

Note

: After installing a GBIC 1000T module, the link LED will light even before a valid cable has been

connected. This is a normal condition for most 1000BaseT GBIC modules.

2.3.2 Removing a GBIC

Caution: GBIC 1000T modules run hot under normal operating conditions. When it has been removed from

the system, place it on a heat resistant surface and allow the module to cool before handling.

Note

: Unnecessary removals/insertions of a GBIC module will lead to premature failure of the GBIC. The

rated duty cycle for a GBIC module is 100 to 500 removals/insertions.

Follow the steps below to remove a GBIC interface from a Gigabit Ethernet module:

1. Disconnect the cable from the GBIC module.

Release the GBIC from the slot by simultaneously squeezing the locking tabs on both sides of the

GBIC.

3. Slide the GBIC out of the slot.

4. GBIC 1000SX and GBIC 1000LX modules: Install the rubber plugs in the GBIC optical bores, and

place the GBIC in protective packaging.

2.3.3 GBIC Care and Handling

Follow these GBIC maintenance guidelines:

•

GBICs are static-sensitive. To prevent ESD damage, follow your normal board and component

handling procedures. Wear an ESD wrist strap

•

GBIC 1000SX and GBIC 1000LX modules are very sensitive to dust and contaminants. When they

are not connected to a fiber-optic cable, install the rubber plugs in the optical bores

•

The ferrules of the optical connectors may pick up debris that can obstruct the optical bore. Use an

alcohol swab or equivalent to clean the ferrules of the optical connector

2.4 Installing Optional Hardware Modules

Follow the steps below to install your media modules (10/100/1000BaseT, 1000BaseX GBIC, 1000BaseSX

or 100BaseFX):

1. Using a flat-head screwdriver (not included), remove the slot cover plate

from the switch.

2. Touch a grounded, metal object to discharge any static electricity on your

body, and then remove the module from its protective packaging (being

careful not to touch any board components or connectors).

3. Slide the module firmly into the module slot until it has

clicked into place. The module’s faceplate should be

flush with the front panel of the switch.

4. Replace the screws to secure the module, being

careful not to over-tighten the screws.

5. Connect network cables to the module port.

6. Restore power to the switch if necessary, or reset the

switch.

2.5 Connecting Power

Use the following procedure to connect power to the switch:

Important: Carefully review the power requirements (Chapter 2.1.3) before connecting power to the switch.

1. Plug one end of the supplied power cord into the power connector on the back of the unit.

2. Plug the other end into a grounded AC outlet.

3. Turn on the switch’s power. The Power LED will begin its initialization process.

The front panel LEDs blink and the Power LED illuminates when it has initialized. The switch is ready for

connection to the network.

Important:

If the power does not come on, check the next section to ensure you are using the correct

cabling.

2.6 Connecting to the Network

The switch may be connected to an Ethernet network with the unit powered on or off.

Use the following

procedure to make your network connections:

1. Connect your network devices to the switch, following the cable guidelines outlined below.

2. After the unit is connected to the network, it can be configured for management capabilities (see

the following chapters for information on configuration).

2.6.1 10/100BaseT Ports Cabling Procedures

The 10/100 ports on the IntraCore 3500 series allow for the connection of 10BaseT or 100BaseTX network

devices. The ports are compatible with IEEE 802.3 and 802.3u standards.

Important: The switch must be located within 100 meters of its attached 10BaseT or 100BaseTX devices.

Use the following guidelines to determine the cabling requirements for your network devices:

•

Connecting to Network Station: Category 5 UTP (Unshielded Twisted-

Pair) straight-through cable (100 meters maximum) with RJ-45 connectors

•

Connecting to Repeater/Hub/Switch’s Uplink port: Category 5, UTP

straight-through cable (100 meters maximum) with RJ-45 connectors

Note: There aren’t specific uplink ports on these switches. All 10/100 ports on

these switches are auto-sensing MDI/MDI-X. This advanced feature means that the

10/100 ports will automatically determine whether the device at the other end of the link is a hub, switch or

workstation, and adjust its signals accordingly.

Although 10/100BaseT requires only pins 1, 2, 3 and 6, Asanté strongly recommends cables with all 8 wires

connected as shown in Table 2-1 below.

1000BaseT requires that all four pairs (8 wires) be connected correctly, using Category 5 or better

Unshielded Twisted Pair (UTP) cable (to a distance of 100 meters). Table 2-1 shows the correct pairing of all

eight wires.

Pin Number

Pair Number & Wire Colors

2 White/Orange

2 Orange/White

3 White/ Green

1 Blue/White

1 White/Blue

3 Green/White

4 White/Brown

4 Brown/White

Table 2-2 Pin Numbers and Wire Colors

2.6.2 Gigabit Ethernet Ports Cabling Procedures

Cabling requirements for the optional hardware modules depend on the type module that has been installed.

Use the following guidelines to determine the cabling requirements for your modules:

•

1000BaseSX GBIC: Cables with SC-type fiber connectors; 62.5-micron multimode fiber (MMF)

media up to 275 meters (902 feet) long, or 50-micron MMF media up to 550 meters (1805 feet)

long

•

1000BaseLX GBIC: Cables with SC-type fiber connectors; 10-micron single mode fiber media up to

5 kilometers (3.1 miles) long

•

1000BaseLX Long Haul GBIC: Cables with SC-type fiber connectors; 10-micron single mode fiber

media up to 100 kilometers (62 miles) long

•

1000BaseT: Category 5 or better Unshielded Twisted Pair (UTP) cable to a distance of 100 meters

(328.1 feet)

2.7 Setup

The following sections describe the steps for setting up the switch for basic configuration, and putting into

place basic security measures (setting up password protection, changing from the default IP address and

configuring the SNMP host table).

In order to configure the switch, you will need to connect to it through a console (out-of-band management),

through your web browser, or through a telnet session.

2.7.1 Connecting to a Console

When attaching a workstation to the device, a standard straight-through CAT5 cable may be used, even

when the workstation is attached via a patch panel. No crossover cable is needed with the MDX/MDI ports.

It is recommended that the switch be kept off the network until proper IP settings have been set.

To connect the switch to a console or computer, setup the system in the following manner:

1. Plug power cord into the back of unit.

2. Attach a straight-through serial cable between the RS232 port and a COM port on the PC.

3. Setup a HyperTerminal (or equivalent terminal program) in the following manner:

• Open the HyperTerminal program, and from it’s file menu, right click on

Properties

• Under the Connect To tab, choose the appropriate COM port (COM1, COM2, etc)

• Under the Settings tab, choose VT100 for Emulation mode

• Select Terminal keys for Function, Arrow and Ctrl keys. Be sure the setting is for Terminal keys,

NOT Windows keys

• Back under the

Connect To

tab, press the

Configuration

button

• Set the data rate to 9600 Baud

• Set data format 8 data bits, 1 stop bit and no parity

• Set flow control to NONE

Now that terminal is setup correctly, power on the switch (boot sequence will display in terminal).

2.7.2 Connecting Via the Web Browser

To connect to the switch via your web browser, you must first have configured your computer’s IP address to

be on the same IP address subnet as the switch (The switch’s default IP is

192.168.0.1

). For more

information on how to configure your TCP/IP settings, please refer to your computer manufacturer’s user’s

manual.

You may now launch your web browser and enter the switch’s default IP address into the address field. The

Introduction page will appear, and you may proceed through the pages to configure each variable. See

Chapter 5. Web-Based Interface for more information on configuring the switch via your web browser.

2.7.3 Connecting Via Telnet

To connect to the switch via a telnet session, you must first have configured your computer’s IP address to

be on the same IP address subnet as the switch (192.168.0.X). For more information on how to configure

your TCP/IP settings, please refer to your computer manufacturer’s user’s manual.

You may now run a telnet session to configure and manage your switch. The Enter Password screen will

appear. Enter the default password to access the Main Menu, and proceed to select the variables that you

wish to configure. See Chapter 3. Configuration for more information on configuring the switch via telnet.

2.8 Changing the Password

The default password (which is Asante, and is case sensitive), may allow immediate access to ANYONE on

the network. To protect your switch from unauthorized changes to the configuration, you must change the

administrator’s password. It can only be changed through the console or telnet interfaces.

To change the administrator’s password, follow these steps:

1. Establish a telnet session, and type

Asante

at the password prompt.

2. Press Enter to proceed.

3. Type

to access the Configuration menu.

4. Type

to access the User Interface Configuration sub-menu.

5. Type

to select Change Administrator’s Password.

6. Type the current password (Asante) and press Enter.

7. Type the new password and press

Enter

8. Re-type the new password to confirm your entry, and press

Enter

2.9 IP Assignment

To change the IP address of the switch from the default setting:

1. Access the System IP Configuration menu by typing

in the Configuration menu.

2. Type the command letter of the option you want to change.

3. Type the new address at the prompt.

To cancel a change, type ctrl-c at the command prompt.

4. Press Enter. The IP setting change for the switch takes effect.

5. Type q to quit and return to the Configuration menu.

When the reset is complete the switch should be seen on your network. If not, check the IP information

again to ensure that all the data is correct.

2.10 SNMP Management

The SNMP Configuration Menu allows you to configure the unit’s read and write community strings, and to

enable or disable authentication traps. This menu also allows you to specify which of your network

management stations will receive traps from the switch.

The n option in the Configuration Menu displays the SNMP (Simple Network Management Protocol)

Configuration Menu, as shown below.

IntraCore SNMP Configuration Menu

SNMP Read Community: public

SNMP Write Community: private

Trap Authentication: Disabled

SNMP Trap Receivers:

IP Address Community

1. xxx.xxx.xxx.xxx public

2. <empty> <empty>

3. <empty> <empty>

4. <empty> <empty>

r Set SNMP Read Community

w Set SNMP Write Community

t Toggle Trap Authentication Enable/Disable

a Add/Update SNMP Trap Receiver

d Delete SNMP Trap Receiver

q Return to previous menu

Command

Important! Be sure to change the SNMP community strings in order to prevent unauthorized access to

management information. See Chapter 3 for details.

Also, see Chapter 6. SNMP Management for more detailed information on the SNMP protocol.

2.11 Using the Stacking Feature (IC3524 only)

The IC3524 firmware v.1.1 (or later) offers a stacking feature that allows the user to stack up to eight units,

all sharing one IP address of the master switch (unit #1). This is an efficient and cost-effective way to add

ports as needed. The following lists the characteristics of stacking that the user needs to be aware of:

• Uses any physical media supported by the switch: copper or fiber, Fast Ethernet or Gigabit

Ethernet, or the special stacking kit shown below (sold separately)

IC35-SKT Stacking Kit

P/N 99-00710-01

• All stacked units are managed through connection to the master switch, via console, telnet or web

interfaces

Note

: While the user may manage the stack via console, telnet or web interface, the initial

formation of the stack may only be done by connection to a console.

• The switches need no extra software, but they must all have the 1.1 firmware installed (see

Chapter 3.14 for firmware upgrade instructions)

Follow the steps below to install (build) a stack:

1. Physically stack the units, in an equipment rack, or on a flat, stable surface (Asanté recommends

that the stack is formed from the bottom up for ease of adding additional units).

2. Units are connected via the Gigabit ports (see section 2.4 for instructions on installing the optional

modules). Starting with the first unit in the stack (the bottom unit, in the photo below), connect the

Ethernet cable or stacking cable from Gigabit port #26 to the Gigabit port #25 of the next unit and

continue the connections to the last unit in the stack. The result is a stack with n x 24 10/100 ports

and 2 Gigabit ports, where n is the number of units in the stack (up to eight).

Page is loading ...

Asante Technologies IntraCore IC3524-2T User manual

Brand: Asante Technologies

Model: IntraCore IC3524-2T

Category: Network switches

Type: User manual

This manual is also suitable for

Download PDF

report

Asante Technologies IntraCore IC3524-2T User manual

This manual is also suitable for

Asante Technologies IntraCore IC3524-2T User manual

Related papers

Other documents