Canon REALiS X600 User manual

User Command Specifications

1

C

over

ver. 01.0100/05 2005.12.27

ver. 01.0100/04 2005.12.5

ver. 01.0100/03 2005.11.14

ver. 01.0100/02 2005.11.10

ver. 01.0100/01 2005.11.1

Canon projector SX6/SX60/X600 User Commands

User Command Specifications Version revision history

1 I. Version revision history

I. Version revision histor

y

Version number of User Commands changed to "01.0100." Entire document

Listing of the parameters for each command changed to the listing obtained by the "RANGE" command. Entire document

PAGE 2

"GUID" in "User Command System" changed to "GUIDE." PAGE 8

PAGE 12

PAGE 11

"AUTOSETEXE" command changed from a "setting" command to a "control" command. PAGE 12, 17

PAGE 17

Error response information added in "Response" of the "AUTOSETEXE" command. PAGE 17

Condition for disabling "INPUT" execution added to "Description" of the "AUTOSETEXE" command. PAGE 17

PAGE 17

PAGE 24

PAGE 26

PAGE 37

PAGE 48

PAGE 66,68

"GUID" parameter of "GET" command changed to "GUIDE." PAGE 72,115

"NOSHOWSTATUS" parameter of "GET" command changed to "NOSHOWSTATE." PAGE 72,118

PAGE 80

PAGE 82

PAGE 101

Description of the version information obtained by "GET COMVER" command added. PAGE 125

"GUID" parameter of "RANGE" command changed to "GUIDE." PAGE 126,170

PAGE 128

PAGE 131

PAGE 135

PAGE 137

PAGE 156

Pressing of POWER button added to the conditions for clearing BLANK of the "BLANK" command. PAGE 18

Listing of the parameters in "Example" of the "RANGE ZSTEPDRV" command revised. PAGE 173

Listing of the parameters in "Example" of the "RANGE ZCONTDRV" command revised. PAGE 174

"INPUT_NOT_FOUND" added to "Error List." PAGE 177

The fact that the guide display is not cleared in "Remote mode" added. PAGE 14

Support for the SX6/SX60/X600 in the "Supported (command) states" of the "ASPECT" command revised.PAGE 26

Operation performed when "GUIDE-OFF" is received in "Remote mode" added. PAGE 62

PAGE 73

PAGE 74

PAGE 103

PAGE 121

PAGE 123

PAGE 124

PAGE 125

In "2. Communication System," "Time out" described separately for SX50 and SX6/SX60/X600. PAGE 2

PAGE 26

PAGE 66

PAGE 68

"BUSY (FOCUS)" and "BUSY (ZOOM)" priority levels raised. PAGE 177

Where revisedDescription of revised versionDate

01.0100/05 2005.12.27

01.0100/01 2005.11.01

Numerical

value

2005.11.1001.0100/02

01.0100/04 2005.12.05

01.0100/03 2005.11.14

Action to be taken when D-Video, SCART or none is applicable in the "Supported (command) states" of

the "GET ASPECT" command revised.

Action to be taken when no SX50 signals are provided in the "Supported (command) states" of the "GET

VKS/HKS" commands revised.

The fact that settings are to be performed by the system for the SX6/SX60/X600 added to the description

of the "WBRGB" command.

"GUID" in "Command List" changed to "GUIDE.

"ZSTEPDRV," "ZCONTDRV," "FSTEPDRV" and "FCONTDRV" commands changed from "control"

commands to "settin

g

" commands

.

Support for the D-Video of the SX6/SX60/X600 in the "Supported (command) states" of the "GET

HPIX/VPIX" commands revised

.

Processing to be undertaken for the "GET POWER" command in cases where zoom or focus lens drive is

underwa

y

deleted.

Support for the local mode of the SX6/SX60/X600 in the "Supported (command) states" of the "GET

MUTE" command revised.

Support for the local mode of the SX6/SX60/X600 in the "Supported (command) states" of the "RANGE

INPUT" command revised.

Support for the local mode of the SX6/SX60/X600 in the "Supported (command) states" of the "RANGE

POWER" command revised.

Support for the D-Video of the SX6/SX60/X600 in the "Supported (command) states" of the "RANGE

HPIX/VPIX" commands revised

.

Action to be taken when D-Video, SCART or none is applicable in the "Supported (command) states" of

the "RANGE ASPECT" command revised.

Version first created.

Support for the SX6/SX60/X600 in the "Supported (command) states" of the "ASPECT" command revised.

Commands for responding normally while drive is maintained added in the "ZCONTDRV" and

"FCONTDRV" commands.

"Auto screen color correction" of the "AUTOSETEXE" command changed to "automatic screen color

correction."

Support for no signals of the SX50 in the "Supported (command) states" of the "VKS/HKS" commands

revised.

"GET ERR" removed from "(4) Zoom/focus stop commands" in the "ZCONTDRV" and "FCONTDRV"

commands.

"Character interval timeout" in communication specifications changed from 10ms to 5 seconds (timeout

between CR and LF is 10ms

)

.

Condition added to "RC/MAIN commands" as a condition for returning from power management standby

in "Power Mana

g

ement Mode.

"

Support for the D-Video input of the SX6/SX60/X600 in the "Supported (command) states" of the

"HPIX/VPIX" commands revised

.

The fact that the screen color correction (WB) is to be adjusted after executing automatic screen color

correction added to "Descri

p

tion" of the "AUTOSETEXE" command

.

PAGE 12,65～68

Statuses of SX6/SX60/X600, TRUE and A-RGB1 in the "Supported (command) states" of the "ASPECT"

command chan

g

ed from "x" to "O.

"

The fact that the response to the "ZCONTDRV" command in cases where zoom drive is underway is

"unconditionall

y

" i:BUSY clearl

y

indicated

.

The fact that the response to the "FCONTDRV" command in cases where focus drive is underway is

"unconditionall

y

" i:BUSY clearl

y

indicated

.

Processing to be undertaken for the "GET LAMPCOUNTER" command in cases where zoom or focus

lens drive is underwa

y

deleted

.

Processing to be undertaken for the "GET PRODCODE" command in cases where zoom or focus lens

drive is underwa

y

deleted.

Processing to be undertaken for the "GET ROMVER" command in cases where zoom or focus lens drive

is underwa

y

deleted.

Processing to be undertaken for the "GET COMVER" command in cases where zoom or focus lens drive

is underwa

y

deleted.

Action to be taken when no SX50 signals are provided in the "Supported (command) states" of the

"RANGE VKS/HKS" commands revised.

Processing to be undertaken for the "GET MODE" command in cases where zoom or focus lens drive is

underwa

y

deleted.

User Command Specifications Contents

1

II

.

Contents

II. Contents

1. Overview

2. Communication Specifications

3. Communication Flow

4. Command System

SX50

SX6 / SX60 / X600

5. Control Mode

6. Key/Emulation function

7. Power Management Mode

8. Command List

9. Details of command

REMOTE

LOCAL

POWER

AUTOＳＥＴEXE

BLANK

INPUT

AUTOPC

DOTS

TRACK

HPOS/VPOS

HPIX/VPIX

SEL

ASPECT

IMAGE

BRI

CONT

SHARP

GAMMA

DGAMMA

PROG

WB

WBRGB

SAT

HUE

RGBGAIN

RGBOFFSET

ACADJUST

MEMCADJ

6AXADJ

6AXR～Ｙ

LAMP

RESET

VKS/HKS

AVOL

MUTE

BVOL

IMAGEFLIP

PMM

PJON

NOSIG

NOSHOW

LOGOPOS

LANG

TERMINAL

KEYLOCK

RCCH

GUID

DPON

LEDILLUMINATE

ZSTEPDRV

ZCONTDRV

FSTEPDRV

FCONTDRV

RC

ＭＡＩＮ

GET

GET MODE

GET POWER

GET BLANK

75

71

72

73

74

66

67

68

69

62

63

64

65

59

60

Page

58

50

44

45

46

53

Item

55

56

57

51

52

54

47

48

49

40

41

42

43

36

37

38

39

31

32

33

34

26

27

29

30

22

23

24

25

18

19

20

21

14

15

16

17

1

2

6

7

8

61

9

10

11

12

13

User Command Specifications Contents

GET INPUT

GET DOTS

GET TRACK

GET HPOS/VPOS

GET HPIX/VPIX

GET SEL

GET ASPECT

GET IMAGE

GET BRI

GET CONT

GET SHARP

GET GAMMA

GET DGAMMA

GET PROG

GET WB

GET WBRGB

GET SAT

GET HUE

GET RGBGAIN

GET RGBOFFSET

GET ACADJUST

GET MEMCADJ

GET 6AXADJ

GET 6AXR～6AXY

GET LAMP

GET VKS/HKS

GET AVOL

GET MUTE

GET BVOL

GET IMAGEFLIP

GET PMM

GET PJON

GET NOSIG

GET NOSHOW

GET LOGOPOS

GET LANG

GET TERMINAL

GET KEYLOCK

GET RCCH

GET GUID

GET DPON

GET LEDILLUMINATE

GET NOSHOWSTATUS

GET FREEZE

GET SIGNALSTATUS

GET LAMPCOUNTE

R

GET ERR

GET PRODCODE

GET ROMVER

GET COMVER

RANGE

RANGE POWER

RANGE BLANK

RANGE AUTOSETEXE

RANGE INPUT

RANGE DOTS

RANGE TRAC

K

RANGE HPOS/VPOS

RANGE HPIX/VPI

X

RANGE SEL

RANGE ASPECT

RANGE IMAGE

RANGE BRI

RANGE CONT

RANGE SHARP

RANGE GAMM

A

RANGE DGAMM

A

RANGE PROG

RANGE WB

RANGE WBRGB

144

145

146

140

141

142

143

Item Page

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95

96

97

98

99

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

128

129

130

131

132

133

134

135

136

137

138

139

User Command Specifications Contents

RANGE SAT

RANGE HUE

RANGE RGBGAIN

RANGE RGBOFFSET

RANGE ACADJUST

RANGE MEMCADJ

RANGE 6AXADJ

RANGE 6AXR～6AXY

RANGE LAMP

RANGE VKS/HKS

RANGE AVOL

RANGE MUTE

RANGE BVOL

RANGE IMAGEFLIP

RANGE PMM

RANGE PJON

RANGE NOSIG

RANGE NOSHOW

RANGE LOGOPOS

RANGE LANG

RANGE TERMINAL

RANGE KEYLOCK

RANGE RCCH

RANGE GUID

RANGE DPON

RANGE LEDILLUMINATE

RANGE ZSTEPDRV

RANGE ZCONTDR

V

RANGE FSTEPDRV

RANGE FCONTDR

V

10. Error List

11. Other

Appendix 1 Reset Items

Appendix 2 Table of Response Patterns by Command

Item Page

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

User Command Specifications 1. Overview

1

.

O

verv

i

ew

・

These specifications describe the methods of controlling the projector from the PC over an RS-232C connection

・

Virtually all operations possible with the remote control can be controlled from the PC

・

The following symbols are used in these specifications

.

[ ]

|

：＝

1. Overview

Symbol

△

□

▽

The definition name is on the left side of this mark, and the definition description is on the right side.

Description

Same as OR

Space with ０ or more characters (20h), Tab (09h), or other separator

Space with 1 or more characters (20h), Tab (09h), or other separator

Separator between parameters　△ , △ | □

The data in [ ] can be omitted.

PAGE 1

User Command Specifications 2. Communication Specifications

4 2. Communication Specifications

Tc ：10ms * For the SX50

：5S (Timeout between CR and LF is 10ms.) * For the SX6, SX60 or X600

Tr Command/response interval:10S

Send data SD SD Send data

Receive data RD RD Receive data

Signal ground SG SG Signal ground

※ In the projector, none of the signal lines except for the three lines of SD, RD and SG are used!

※ If necessary, loop back its own signals at the PC side.

The projector has two control modes, the local mode and remote mode.

Most user commands are used in REMOTE mode.

The two modes are set by the REMOTE and LOCAL commands.

・Initial mode of projector

・

Except for RC and MAIN, all user commands are available in this mode.

・The available user commands are limited.

・

If AC power is supplied to the projector, communication is possible regardless of whether the power is on or off.

None of the remote control and main unit panel buttons except for

POWER can be used.

Flow control

Double-byte characters and single-byte characters are not distinguished. All are considered

sin

g

le-b

y

te characters.

REMOTE command

LOCAL command

(Codes other than those above and delimiters are considered “other separator codes”)

Uppercase and lowercase of alphabetic characters are considered the same character.

Character

interval

Transmission speed

Character length

Stop bit

Parity

Transmission format

Maximum transmission

len

g

th

Delimiters

Maximum of 256 characters (bytes) including delimiters

Delimiters are one of CR, LF, CR+LF, Null (0) (Delimiters are identified automatically.)

Response delimiters are identical to command delimiters.

ASCII code (General-purpose characters: 20h to 7Fh), Tab (09h)

2. Communication Specifications

Item

Communication s

y

ste

m

Communication procedure

Transmission codes

Specifications

RS-232-C Start-sto

p

s

y

nchronization Semi-du

p

lex communicatio

n

19.2Ｋｂｐｓ

8 bits/character

Communicatio

n

system

Projecto

r

Commands

PC

2 bits

None

Variable-length record with terminal as delimiter

No procedure

None

Connection

Specifications

Specification

s

PC: Connected on a "1:1"

basis with the pro

j

ecto

r

3-line connection of SD,

RD, and SG

Connection

s

y

stem

Connection

signal line

Item

The connection diagram is

here.

Connection

cable

Dedicated cable

Control

Mode

Communicatio

n

system

Response

Time out

Error control

Break signal

None

Control is switched to this mode by the REMOTE command.

Communication between the PC and projector is performed by the projector responding by sending a response to the

command sent from the PC.

Not supported

LOCAL mode

REMOTE mode

PC

プロジェクタ

専用ｹｰﾌﾞﾙ

COM

PORT

SERVICE

PORT

ＰＣ－プロジェクタ　接続形態

Canon

PC - Projector connection status

Dedicated cable

Projector

PAGE 2

User Command Specifications 2. Communication Specifications

Request transmissions sent from PC to the projector

△<Command character strings> △<Delimiters>

One of CR (0Dh), LF (0Ah), CR+LF (0Dh+0Ah), Null (00h

)

Null

□

BUSY

■

WARN

■

ERR

□

GET

□

RANGE

Control

Projector control command. The format is shown below. ■

OK

■

BUSY

■

WARN

■

ERR

□

GET

□

RANGE

Setting

Command that sets values for each parameter

.

The format is shown below.

■

OK

■

BUSY

■

WARN

■

ERR

□

GET

□

RANGE

Reference

Requests current value of each parameter. The format is shown below. □

OK

■

BUSY

■

WARN

■

ERR

■

GET

□

RANGE

□

OK

■

BUSY

■

WARN

■

ERR

□

GET

■

RANGE

Requests range which can be set for each parameter. The format is shown

below.

Null Commands

Character string

<Setting command character strings>:= <Parameter

name>△=△<Parameter value

>

Control command

Character string

Transmissio

n

forma

t

T

yp

e

ResponseDescription

Commands

Commands with a command character string length of 0. No command

processing is performed.

<Command character

strings>

■

Type

OK

Setting command

Character string

　　For the definition of <Parameter value>, refer to "Parameter definitions."

<Reference command character string>:=?

△<Parameter name> |

GET□<Parameter name>

Reference

command

Character string

Command ListReference

Character strings consisting of 0 or more alphanumeric

characters

<Null command character string>:= <Character string with length

0>

<Control command character string>:= <Control

name>□<Parameter value>

<Range request command character string>:=

RANGE□<Parameter name>

PAGE 3

User Command Specifications 2. Communication Specifications

Transmissions sent from Projector to PC in response to commands from PC

<Response character string> <Delimiter

>

The first two characters are always <one lowercase letter>:

The first character indicates the response type.

State response i:OK i:BUSY etc.

Warning w:USER_COMMAND..

Error e:000B INVALID..

Reference command response g:AVOL=10

Range request command respons

e

r:VKS=N, -50, 50

Delimiters for commands sent from P

C

OK

<OK response character string>:=i:O

K

BUSY

This response is sent when a command cannot be received during processing.

Wait for a few moments, and then try sending the command again.

<BUSY response character string>:=i:BUS

Y

> IMAGE=2

< i:BUSY

WARN

> IMAGE=2

< w:USER_COMMAND_VERSION_IS_UPDATED

ERR

An error message is output.

<Error response character string>:= e:<Error code

>

□<Error message>

※

> abcdefg

< e:0002 INVALID_COMMAND

GET

Request response for each parameter.

<GET response character string>:=g<Parameter name>=<Value

>

> GET LANG or ? LANG

< g:LANG=JPN

RANGE

This is the settable range response for each parameter.

> RANGE CONT

< r:CONT=N, -20, 20

WARN

response

ERR

response

GET

response

RANGE

response

<Response character

string>

Refer to “Error List”!

<Error code> is expressed as a four-digit hexadecimal number.

g

Example:

Response

Type

T

yp

e

Example:

After processing of each command is completed, a response is sent indicating that the next command

can be received.

e

This response is sent when warning information is issued.　Note that this command cannot be

executed.

Transmissio

n

forma

t

Description

i

Character strings consisting of one or more ASCII characters.

w

MeaningResponse typ

e

Example

r

Example:

OK

response

BUSY

response

※ <For <Setting value range> refer to the RANGE command.

PAGE 4

User Command Specifications 2. Communication Specifications

Transmission is recognized when delimiter is received.

Even if a maximum transmission length is received, the entire received transmission will be lost unless a delimiter is received.

The <Parameter value> is defined as shown below.

<Parameter value>:=<Value 1

>

▽<Value 2> ▽.. ▽ <Value n>

<Value> := <Numerical value> | <ID> | “<Character string>”

:= [<Sign>] <Decimal character string (Min. 1 character to Max. 5 characters)>

:= 1 or more ASCII characters (20h to 7Fh)

:= 0 or more ASCII characters (20h to 7Fh)

The connection diagram (example) for the cable connecting the PC and projector is shown below.

The range of valid values is -32768 to 32767.

Cable

Other

<ID>

Transmissio

n

recognitio

n

Paramete

r

value

Definition

①②

③④ ⑤

⑥⑦⑧

15

69

D-SUB 9pin FEMALE

PC PJ

MINI DIN 8pin MALE

SHIELD

1 CD (DCD)

2 RD (RXD)

3 SD (TXD)

4 ER (DTR)

5 SG (GND)

6 DR (DSR)

7 RS (RTS)

8 CS (CTS)

9 CI (RI)

3 SD (TXD)

5 RD (RXD)

4 SG (GND)

2 NC

1 RS(RTS)

6 NC

7 NC

8 NC

PC

PJ

接続例 1

SHIELD

1 CD (DCD)

2 RD (RXD)

3 SD (TXD)

4 ER (DTR)

5 SG (GND)

6 DR (DSR)

7 RS (RTS)

8 CS (CTS)

9 CI (RI)

3 SD (TXD)

5 RD (RXD)

4 SG (GND)

PC PJ

接続例 2

PCで「CS」、「DR」を使用する場合の自己折返し結線例。

SHIELD

1 CD (DCD)

2 RD (RXD)

3 SD (TXD)

4 ER (DTR)

5 SG (GND)

6 DR (DSR)

7 RS (RTS)

8 CS (CTS)

9 CI (RI)

3 SD (TXD)

5 RD (RXD)

4 SG (GND)

PC

PJ

接続例 3

最小限の結線例です。

キヤノン標準ケーブルの結線です。

PC側の「RS」は使用しないでください！

Sample 1

Sam

p

le 3

Sample 2

Example of self-loopback connections when the

"CS" and "DR" pins are used in the connector of

the PC.

Canon's standard cable is used for

these connections.

Do not use the "RS" pin in the

connector of the PC!

Example of minimally required connections.

PAGE 5

User Command Specifications 3. Communication Flow

1 3. Communication Flow

One response is always returned for each command sent from the PC.

Within Tr

*The timeout interval between command and response (Tr) is 10 seconds.

Response

reception

timeout

If a response is not received within Tr (timeout interval between command and response) while in response reception

standby after sending a command at the PC, resend the command in the “response reception timeout”.

Response

PC

Commands

Projecto

r

3. Communication Flow

Transmission

sent

Transmission

received

Command/

Response

At the sending side (PC), the transmission is sent within character intervals of Tc (character interval timeout).

At the receiving side (Projector), data able to be received within the character interval of Tc is held, and receiving of a

delimiter is considered “transmission received”.

If a received character interval exceeds Tc or a delimiter is not received within 256 characters, all data already received is

lost, and the mode is reset to receive standby again.

(However, note that a response may not be returned when the internal receive buffer overflows due to reception of a large

amount of data.)

PAGE 6

User Command Specifications 4. Command System SX50

1 4.

C

SX50

SX50. User Command System

Display setting INPUT

*User commands use only automatic selection of input signals.

*Running of Auto PC will change the values set in “Input signal settings”.

*This is set for each input signal and image quality.

RESET IMAGE

System setting

RESET SYSTEM

*Running of Auto PC will change the values set in “Input signal settings”.

*Same as “Setting/Control”-“Image Adjustment”-“Image Quality Select”.

Emulate

Reference

※ Indicates functions that are available in the menu but not available in the user commands.

IMAGEFLIP

TERMINAL

KEYLOCK

Brightness setting

Contrast setting

Sharpness setting

Gamma correction

BRI

CONT

4. Command System

RESET

IMAGE

SEL

ASPECT

AUTOPC

Image adjustment reset

Image

adjustment

Input select

PMM

BVOL

RCCH

LANG

RESET

Language setting

RC

INPUT

VKS/HKS

AUTOPC

AVOL

IMAGE

MUTE

Key emulate

Retrieve each data

Setting range request

GET

RANGE

MAIN

No show status setting

Freeze image

Presentation timer setting

Remote control emulate

Volume adjustment

Digital zoom

Image quality select

Audio mute

Input switching

Keystone

Auto PC

Spotlight

Reset

Remote control/Key

Power supply POWER

Key lock

Password registration

Password setting

Remote control setting

Terminal setting

Power management

Electronic sound

Auto PC

Menu display position setting

User screen setting

Flip display

Image quality select

Input signal settings

Input signal selection

Screen settings

Mode change

Setting/Control

REMOTESwitch to Remote mode

Switch to Local mode LOCAL

Total number of dots adjustment

Tracking adjustment

Horizontal/Vertical position adjustment

Horizontal/Vertical resolution adjustment

DOTS

TRACK

HPOS/VPOS

HPIX/VPIX

Startup screen

LOGOPOS

NOSIG

NOSHOW

PJON

User screen registration

User image position

Input when no signal

Screen when nothing shown

SHARP

GAMMA

HUE

ACADJUST

Dynamic gamma

Progressive

Screen color correction

DGAMMA

PROG

WB

Lamp mode setting LAMP

RGB adjustment WBRGB

6-axis

adjustment

6ＡＸＲ～Ｙ

Color saturation setting

Hue setting

Advanced color adjustment

SAT

PAGE 7

User Command Specifications SX6 / SX60 / X600

1 SX6 / SX60 / X600

SX6, SX60 or X600 User Command System

Mode chang

e

Setting/Control

Display setting

*Running of Auto PC will change the values set in “Input signal settings”.

User screen setting

RESET IMAGE

System setting

Other settings

RESET LAMPTIME

RESET SYSTEM

Remote control/Ke

y

*Same as “Setting/Control”-“Image Adjustment”-“Image Quality Select”.

*Running of Auto PC will change the values set in “Input signal settings”.

Emulate

Reference

※ Indicates functions that are available in the menu but not available in the user commands.

*User commands use only automatic selection of input signals.

LEDILLUMINATE

AUTOSETEXE

Input signal selection SEL

Auto PC AUTOPC

Screen color correction WB

DOTS

TRACK

HPOS/VPOS

HPIX/VPIX

Total number of dots adjustment

Tracking adjustment

Horizontal/Vertical position adjustment

Horizontal/Vertical resolution adjustment

Switch to Local mode LOCAL

Switch to Remote mode REMOTE

Input signal settings

Input select INPUT

Screen settings ASPECT

Menu display position setting

Flip display IMAGEFLIP

Progressive PROG

Image adjustment reset RESET

Image quality select IMAGE

*This is set for each input signal and image quality.

Direct power-on

Power management mode

Auto setup

GUIDE

LANG

KEYLOCK

BVOL

DPON

PMM

Guide

Language setting

Key lock

Electronic sound

LED illumination

AUTOPC

INPUT

IMAGE

POWERPower supply

Auto set

AVOL

MUTE

BLANK

VKS/HKS

ZSETPDRV

Auto PC

Input switching

Image quality select

ZCONTDRV

FCONTDRV

FSETPDRV

Freeze image

Volume adjustment

Audio mute

No show status setting

Spotlight

Digital zoom

Keystone

Zoom

Focus

Image

adjustment

Retrieve each data

Setting range request

GET

RANGE

Remote control emulate

Key emulate

RC

MAIN

Presentation timer setting

RGB adjustment WBRGB

User screen registration

User image position

Screen when no signal

Screen when nothing shown

Startup screen

LOGOPOS

NOSIG

NOSHOW

PJON

Color adjustment

BRI

CONT

SHARP

GAMMA

Brightness setting

Contrast setting

Sharpness setting

Gamma correction

Advanced adjustment

Lamp mode setting LAMP

Remote control setting

Password setting

Password registration

Lamp counter reset

Factory settings RESET

RESET

RCCH

Color saturation setting

Hue setting

Gain adjustment

Offset adjustment

Dynamic gamma

Memory color correction

6-axis color adjustment

SAT

HUE

RGBGAIN

RGBOFFSET

DGAMMA

MEMCADJ

6AXADJ

6-axis adjustment 6ＡＸＲ～Ｙ

PAGE 8

User Command Specifications 5. Control Mode

1 5. Control Mode

The table below shows the states and limitations of the LOCAL and REMOTE control modes.

Mode

Item

Status State indicator

Constant remote indicator ※2

ALM ALM state indicato

r

ALM state indicato

r

・

AC

power supp

l

y

t

o pro

j

ec

t

o

r

・

REMOTE

comman

d

・

M

anua

l

power on

/

o

ff

・

LOCAL

comman

d

・

P

ower managemen

t

s

t

an

db

y

/

ex

it

mo

d

e

t

rans

f

e

r

Main unit key

s

All available Only POWER button is available

Emulation Available

※1

Not available

5 minutes elapsed from no signal Operation is as follows depending on the model.

・

・Signal inpu

t

・REMOTE command

・Remote control button presse

d

・Main unit button presse

d

・Emulation

For the SX50 All commands except for "RC" and "MAIN

"

REMOTE

LOCAL

GET MODE

MAIN

RC

For the SX6, SX60 or X60

0

GET COMVER

GET ERROR

GET FREEZE

GET INPUT

GET LAMPCOUNTER

GET MODE

GET MUTE

GET NOSHOWSTATUS

GET POWER

GET PRODCODE

GET ROMVER

GET SIGNALSTATUS

LOCAL

MAIN

RC

REMOTE

Special mode Executable with remote control or main unit buttons Not executable in any state

(Service mode)

*1 However, switching to the USB mouse function or Special mode is not allowed.

*2 If the control mode is REMOTE, the following are displayed regardless of whether the power is on or off.

*3 When the power management setting is "standby" or "exit"

LED indicator pattern during REMOTE mode

■ ■

Mode where projector control/operation is

performed by a PC or other external device.

(The PC or other external device is connected by

a serial cable.)

Mode where projector control/operation is

performed by the main unit or remote control.

Initial mode when microcomputer is started.

5. Control Mode

LOCAL mode

Description

REMOTE mode

Remote control

keys

All available

Command/paramete

r

Remarks

Commands supported

Command/paramete

r

Remarks

5 minutes elapsed from no

signal

Model

Return

No switching to standby or exit

mode.

Transition method

Operation

buttons

LED

Switching

Power

management

standby and exit

modes

※3

Control is switched to "local

mode" after mode switching.

SX6

SX60

X600

SX50

Only POWER button is available

PAGE 9

User Command Specifications 6. Key/Emulation function

1

6

.

K

ey

/E

mu

l

a

ti

on

f

unc

ti

on

The table below shows how the main unit/remote control keys and emulation function operate in each control mode

6. Key/Emulation function

Key/Emulation

LOCAL mode

Unlock

Remote

control lock

Main unit

key lock

REMOTE mode

Unlock

Remote control

lock

Main unit key

lock

Main unit key emulation

○

Remote control

Main unit keys

Remote control emulation

○

×

○

×

POWER only

×

POWER only

×

PAGE 10

User Command Specifications 7. Power Management Mode

1 7. Power Management Mod

e

Concerning the processing for switching to the power management standby or exit mode in the remote or local mode

Events for returning from standby mode

・Signal inpu

t

・Pressing of a button on main unit or remote contro

l

Lamp on

・REMOTE command

・RC/MAIN command (excluding RC/MAIN*-REP

)

Lamp off

When the exit mode is established

Power Off

Remote

The countdown is aborted by any command other than

GET/RANGE.

Processing only for commands

enabled in power management

standby mode

Lamp

cooling in

progress

Projecting in

progress

When the standby

mode is established

Power management activated

7. Power Management Mode

SX50

(No countdown is initiated.)

The power management standby or exit mode is established when no signals are supplied for at least 5

minutes.

SX6/SX60/SX60

0

The power management standby or exit mode is

not established.

The power management standby or exit mode is

established when no si

g

nals are supplied for at least 5

Control is switched to the "local mode" in the standby or

exit mode.

Local

Mode

PAGE 11

User Command Specifications 8. Command List

1 8. Command List

Mode Control Setting Reference

1

○

2

○

3

○

4

○

5

○

6

○

7

○

8 ○

9 ○

10 ○

11 ○

12 ○

13 ○

14

○

15 ○

16 ○

17 ○

18 ○

19 ○

20 ○

21 ○

22 ○

23 ○

24 ○

25 ○

26 ○

27 ○

28 ○

29 ○

30 ○

31 ○

32 ○

33 ○

34 ○

35 ○

36 ○

37 ○

38 ○

39

○

40

○

41 ○

42 ○

43 ○

44 ○

45 ○

46 ○

47 ○

48 ○

49 ○

50 ○

51 ○

52 ○

53 ○

54 ○

55 ○

56 ○

57 ○

58 ○

59 ○

60 ○

61 ○

62

○

63

○

64 ○

65 ○

Item

TERMINAL Terminal setting

Remote control operation emulation

LOGOPOS User image position setting

LANG Language selection

GUIDE Guide setting

DPON

Flip display control

AVOL Volume adjustment

BVOL Beep sound setting

MUTE Mute

Direct power-on setting

PMM

Command type

Gamma correction

Screen settings

Contrast setting

Sharpness setting

Input signal selection

Vertical position adjustment

Auto PC execution

Horizontal resolution adjustment

Dynamic gamma

GAMMA

DGAMMA

WBRGB

Progressive

WB Screen color correction

Screen color correction (RGB adjustment)

Commands Description

Image mode

Brightness settingBRI

VPIX

INPUT

Power supply control

Input terminal select

AUTOPC

DOTS Total number of dots adjustment

Input

signal

settings

HPOS

VPOS

HPIX

Vertical resolution adjustment

TRACK

R setting

RESET

Y setting

LAMP Lamp mode setting

6AXM

C setting

M setting

6AXR

Color saturation setting

Hue setting

ACADJUST

HUE

Advanced color adjustment

RGBGAIN RGB gain adjustment

RGBOFFSET RGB offset adjustment

SAT

REMOTE

Switching to Remote mod

e

LOCAL

Switching to Local mode

POWER

AUTOSETEXE

Auto setup execution

BLANK

BLANK function

SEL

ASPECT

IMAGE

PROG

CONT

SHARP

IMAGEFLIP

Power management

6AXG

HKS

6AXC

6AXB

VKS

G setting

B setting

Trapezoid adjustment (vertical keystone)

RANGE

Setting range reques

t

KEYLOCK Key lock setting

RCCH Remote control setting

RC

GET

Retrieve data

Front panel button operation emulationMAIN

NOSHOW Display screen setting when nothing shown

8. Command List

PJON Display screen at startup setting

NOSIG Display screen when no signal setting

Tracking adjustment

Horizontal position adjustment

LEDILLUMINATE

Emotional LED and signal sensing LED lighting control

ACADJUST Memory color correction

6AXADJ 6-axis adjustment ON/OFF

6AXY

Trapezoid adjustment (horizontal keystone)

Reset

6-axis

color

adjust

Focus lens continuous drive controlFCONTDRV

Focus lens step drive controlFSTEPDRV

Zoom lens continuous drive controlZCONTDRV

Zoom lens step drive controlZSTEPDRV

PAGE 12

User Command Specifications 9. Details of command

1 9. Details of command

9. Details of command

Descriptions of each command are provided starting from the next page.

The command descriptions have the format shown below.

* Alphabetic command nam

e

* This indicates the command format.

* This explains the required parameters for the command.

* This describes the command response.

* This includes the command function, conditions, and notes.

* This provides command usage examples.

*

Supported Command States

*

OFF ON PM

×

○

×

“○” when the power supply state is enabled while power management is in standby.

Input signal is required when “×”.

“○” when power supply state is ON.

“○” when power supply state is OFF.

Command

s

supported

The command is enabled

in control modes marked

by “○”.

※Command type

×××

○○○

Parameter types

Format

Example

D-Video

Response

Description

A-RGB2 Comp Video S-Video

Model Power

Function * This briefly describes the command function

.

Parameter

Mode

01.**** 11.**** 11.**** 11.****

Commands

Mode Control Setting Reference

D-RGB A-RGB1

Input

Remarks

SCART LocalNone Remote

SX50

The command is enabled in states marked by “○”.

○

×××

○

×

SX6 SX60 X600

This defines the environments that support the command (power supply state, input signal

state, control mode

)

.

Indicated here are the commands supported by each model (and user command version). "O": supported; "x":

not supported.

○○○○

PAGE 13

User Command Specifications (SET command)

0

PAGE 13

User Command Specifications (GET command)

0

PAGE 13

Page is loading ...

Canon REALiS X600 User manual

This manual is also suitable for

Canon REALiS X600 User manual

Related papers

Other documents