Page 1/4
Thank you for purchasing this quality product. Be sure to check all packing material carefully for
small parts that may come loose inside the carton during shipment.
UNIT SHOULD BE INSTALLED BY 2 OR MORE PERSONS.
BEFORE USING THIS PRODUCT PLEASE READ, UNDERSTAND, AND FOLLOW THESE INSTRUCTIONS.
Save these instructions for future reference.
All Beds need to be set up in the exact final
location so that after full assembly it will not
need to be moved. Moving the bed will cause
the support legs to move out of perpendicular
(90 degree), weaken the support system, and
may allow the bed to collapse.
FOR INDOOR USE ONLY
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ICB-401
ICB-402L
ICB-400
TOOLS REQUIRED (NOT PROVIDED)
PHILLIPS SCREWDRIVER
COMPONENTS LIST: ICB-401
No. Description Sketch Quantity
1 Footboard 1 PC
2 Bun Foot 2 PCS
3 Support legs with leveler 4 PCS
HARDWARE LIST: ICB-400
No. Description Sketch Quantity
A Bolt Ø5/16"*2-1/4" 8 PCS
B Lock Washer Ø5/16" 8 PCS
C Flat Washer Ø5/16" 8 PCS
D Allen Wrench 5mm 1 PC
HARDWARE LIST: ICB-402L
No. Description Sketch Quantity
E Wood Screw 8 PCS
F Allen Wrench 4mm 1 PC
COMPONENTS LIST: ICB-402L
No. Description Sketch Quantity
1 Bed rails 2 PCS
2 Slats 4 PCS
COMPONENTS LIST: ICB-400
No. Description Sketch Quantity
1 Headboard 1 PC
2 Left Leg 1 PC
3 Right Leg 1 PC
4 Wood Stretcher 1 PC
ITEM NO: ICB-400-BCH/BLK/EGG/GRY-KD-1 Queen Sleigh Bed HB
ICB-402L-BCH/BLK/EGG/GRY-1 Queen Side Rails
ICB-401-BCH/BLK/EGG/GRY-1 Queen Sleigh Bed FB
10-26-2017
10-26-2017
Page 2/4
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
STEP 3: Lay footboard back down on a padded, clean surface. Attach bun feet to footboard. Turn
footboard right side up.
Leveler
Bun Foot
b
a
Wood Screw
Slat bearer
Side Rail
HB Backside
Left Leg
Right Leg
STEP 1: Lay the headboard face down on a
soft surface. Attach the left leg and right leg
to headboard by using 6 bolts(A), lock
washers(B) and flat washers(C).
STEP 2: Attach the wood stretcher to the
legs by using 2 bolts(A), lock washers(B)
and flat washers(C).
HB Backside
Wood Stretcher
A
B
C
D
STEP 4: The slat bearers have been attached in position b. The slat bearers can be moved into
position a depending on the mattress/platform configuration. Remove the bolts and screws from
the slat bearers and side rails as shown below. Then re-attach the slat bearers to the side rails in
desired position with bolts, lock washers, flat washers, and screws. Caution: Do not over tighten
bolts as this may loosen the threaded inserts in the side rails.
ITEM NO: ICB-400-BCH/BLK/EGG/GRY-KD-1 Queen Sleigh Bed HB
ICB-402L-BCH/BLK/EGG/GRY-1 Queen Side Rails
ICB-401-BCH/BLK/EGG/GRY-1 Queen Sleigh Bed FB
A
B
C
D
10-26-2017
Page 3/4
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
STEP 5: Hook the side rails to the headboard and footboard.
Side Rail
Side Rail
STEP 6: Attach the support legs with leveler to the
slats. Adjust the levelers on bottom of support legs
when necessary. Support Leg
Leveler
This End Up
Slat
Slat bearer
Side Rail
Headboard
ITEM NO: ICB-400-BCH/BLK/EGG/GRY-KD-1 Queen Sleigh Bed HB
ICB-402L-BCH/BLK/EGG/GRY-1 Queen Side Rails
ICB-401-BCH/BLK/EGG/GRY-1 Queen Sleigh Bed FB
10-26-2017
Page 4/4
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
STEP 7: Arrange the slats on the slat bearers equally and attach to the slat bearers with wood
screws (E).
Wood Screws (E)
FUNCTIONALITY INSTRUCTION
ICB-400
ICB-402L
ICB-401
ITEM NO: ICB-400-BCH/BLK/EGG/GRY-KD-1 Queen Sleigh Bed HB
ICB-402L-BCH/BLK/EGG/GRY-1 Queen Side Rails
ICB-401-BCH/BLK/EGG/GRY-1 Queen Sleigh Bed FB
1 Powered USB Port for
Charging on both sides
10-26-2017
Page 1/6
Thank you for purchasing this quality product. Be sure to check all packing material carefully for
small parts that may come loose inside the carton during shipment.
UNIT SHOULD BE INSTALLED BY 2 OR MORE PERSONS.
BEFORE USING THIS PRODUCT PLEASE READ, UNDERSTAND, AND FOLLOW THESE INSTRUCTIONS.
Save these instructions for future reference.
All Beds need to be set up in the exact final
location so that after full assembly it will not
need to be moved. Moving the bed will cause
the support legs to move out of perpendicular
(90 degree), weaken the support system, and
may allow the bed to collapse.
FOR INDOOR USE ONLY
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ICB-403D
ICB-402L
ICB-412
ICB-400
ICB-402L
ICB-403D
OPTION 2: Quee Storage Panel Bed
OPTION 1: Queen Storage Sleigh Bed
ITEM NO: ICB-400-BCH/BLK/EGG/GRY-KD-1 Queen Sleigh Bed HB
ICB-402L-BCH/BLK/EGG/GRY-1 Queen Side Rails
ICB-403D-BCH/BLK/EGG/GRY-1 Queen LP FB w/Drawers
ICB-412-BCH/BLK/EGG/GRY-KD Queen Panel HB
10-26-2017
Page 2/6
COMPONENTS LIST: ICB-412
No. Description Sketch Quantity
1 Headboard 1 PC
2 Left Leg 1 PC
3 Right Leg 1 PC
4 Wood Stretcher 1 PC
TOOLS REQUIRED (NOT PROVIDED)
PHILLIPS SCREWDRIVER
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
HARDWARE LIST: ICB-412
No. Description Sketch Quantity
N Bolt Ø5/16"*1-3/4" 10 PCS
O Lock Washer Ø5/16"10 PCS
P Flat Washer Ø5/16"10 PCS
Q Allen Wrench 5mm 1 PC
HARDWARE LIST: ICB-403D
No. Description Sketch Quantity
G Bolt Ø1/4"*1-3/4" 6 PCS
H Bolt Ø1/4"*1-1/4" 4 PCS
I Lock Washer Ø1/4" 10 PCS
J Flat washer Ø1/4" 10 PCS
K Wood Screw #8*1" 8 PCS
LWood Screw #8*1-1/2" 5 PCS
M Allen Wrench 4mm 1 PC
COMPONENTS LIST: ICB-402L
No. Description Sketch Quantity
1 Bed rails 2 PCS
2 Slats 4 PCS
COMPONENTS LIST: ICB-403D
No. Description Sketch Quantity
1 Footboard 1 PC
2 Support Leg (for center rail) 1 PC
3 Support Leg (for pedestal) 2 PCS
4 Decking 4 PCS
5 Center Rail 1 PC
6 Bun Foot 2 PCS
7 Support Panel 2 PCS
COMPONENTS LIST: ICB-400
No. Description Sketch Quantity
1 Headboard 1 PC
2 Left Leg 1 PC
3 Right Leg 1 PC
4 Wood Stretcher 1 PC
HARDWARE LIST: ICB-400
No. Description Sketch Quantity
A Bolt Ø5/16"*2-1/4" 8 PCS
B Lock Washer Ø5/16" 8 PCS
C Flat Washer Ø5/16" 8 PCS
D Allen Wrench 5mm 1 PC
HARDWARE LIST: ICB-402L
No. Description Sketch Quantity
E Wood Screw 8 PCS
F Allen Wrench 4mm 1 PC
ITEM NO: ICB-400-BCH/BLK/EGG/GRY-KD-1 Queen Sleigh Bed HB
ICB-402L-BCH/BLK/EGG/GRY-1 Queen Side Rails
ICB-403D-BCH/BLK/EGG/GRY-1 Queen LP FB w/Drawers
ICB-412-BCH/BLK/EGG/GRY-KD Queen Panel HB
10-26-2017
Page 3/6
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
OPTION 1: Queen Storage Sleigh Bed
HB Backside
Left Leg
Right Leg
STEP 1: Lay the headboard face down on a
soft surface. Attach the left leg and right leg
to headboard by using 6 bolts(A), lock
washers(B) and flat washers(C).
STEP 2: Attach the wood stretcher to the
legs by using 2 bolts(A), lock washers(B)
and flat washers(C).
HB Backside
Wood Stretcher
A
B
C
D
A
B
C
D
STEP 3: Lay footboard upside down on a padded, clean surface. Attach support legs (for pedestal)
and bun feet to footboard using 4 bolts(H), lock washers(I) and flat washers(J). Turn footboard
right side up.
Leveler
Bun Foot
H
I
J
M
ITEM NO: ICB-400-BCH/BLK/EGG/GRY-KD-1 Queen Sleigh Bed HB
ICB-402L-BCH/BLK/EGG/GRY-1 Queen Side Rails
ICB-403D-BCH/BLK/EGG/GRY-1 Queen LP FB w/Drawers
ICB-412-BCH/BLK/EGG/GRY-KD Queen Panel HB
10-26-2017
Page 4/6
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
STEP 5: Hook the side rails to the headboard and footboard, Attach support leg and center rail to
headboard and footboard by using 5 wood screws(L).
Headboard
Slat bearer
Side Rail
Side Rail
Side Rail
STEP 4: Attach support leg and support panels to center rail by using 6 bolts(G), lock washers(I)
and flat washers(J).
Support Panel
Support Leg (for center rail)
Center Rail
L
L
GIJ
M
ITEM NO: ICB-400-BCH/BLK/EGG/GRY-KD-1 Queen Sleigh Bed HB
ICB-402L-BCH/BLK/EGG/GRY-1 Queen Side Rails
ICB-403D-BCH/BLK/EGG/GRY-1 Queen LP FB w/Drawers
ICB-412-BCH/BLK/EGG/GRY-KD Queen Panel HB
02-08-2018
Page 5/6
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
STEP 7: Put the decking over the slats, secure decking to the slats with wood screws (K) through
the pre-drilled holes in the decking as shown below.
Make sure that there is a slat
under the pre-drilled hole.
Decking
Slat
Decking
Decking
The slat should support
both pieces of decking.
Decking
Decking
Decking
KDecking
Pre-drilled hole
STEP 6: Arrange slats on the slat
bearers and then lay decking on
top of the slats. Make sure the slats
are positioned along the seams of
the decking as shown in the detail
in STEP 7 under the pre-drilled
hole. Remove the decking and
attach slats to the slat bearers with
wood screws (E).
ITEM NO: ICB-400-BCH/BLK/EGG/GRY-KD-1 Queen Sleigh Bed HB
ICB-402L-BCH/BLK/EGG/GRY-1 Queen Side Rails
ICB-403D-BCH/BLK/EGG/GRY-1 Queen LP FB w/Drawers
ICB-412-BCH/BLK/EGG/GRY-KD Queen Panel HB
Wood Screws (E)
FUNCTIONALITY INSTRUCTION
ICB-403D
ICB-402L
ICB-412
10-26-2017
Page 6/6
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
STEP 3 to STEP 7 are same as OPTION 1
OPTION 2: Queen Storage Panel Bed
ICB-403D
ICB-402L
ICB-400
STEP 1: Lay the headboard face down on a
soft surface. Attach the left leg and right leg
to headboard by using 8 bolts(N), lock
washers(O) and flat washers(P).
STEP 2: Attach the wood stretcher to the
legs by using 2 bolts(N), lock washers(O)
and flat washers(P).
HB Backside
Left Leg
Right Leg OP
Q
O
P
Q
N
N
Wood Stretcher
HB Backside
ITEM NO: ICB-400-BCH/BLK/EGG/GRY-KD-1 Queen Sleigh Bed HB
ICB-402L-BCH/BLK/EGG/GRY-1 Queen Side Rails
ICB-403D-BCH/BLK/EGG/GRY-1 Queen LP FB w/Drawers
ICB-412-BCH/BLK/EGG/GRY-KD Queen Panel HB
1 Powered USB Port for
Charging on both sides
Page 1/4
Thank you for purchasing this quality product. Be sure to check all packing material carefully for
small parts that may come loose inside the carton during shipment.
UNIT SHOULD BE INSTALLED BY 2 OR MORE PERSONS.
BEFORE USING THIS PRODUCT PLEASE READ, UNDERSTAND, AND FOLLOW THESE INSTRUCTIONS.
Save these instructions for future reference.
All Beds need to be set up in the exact final
location so that after full assembly it will not
need to be moved. Moving the bed will cause
the support legs to move out of perpendicular
(90 degree), weaken the support system, and
may allow the bed to collapse.
FOR INDOOR USE ONLY
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ICB-405
ICB-410L
ICB-406L
ICB-404
TOOLS REQUIRED (NOT PROVIDED)
PHILLIPS SCREWDRIVER
COMPONENTS LIST: ICB-405
No. Description Sketch Quantity
1 Footboard 1 PC
2 Bun Foot 2 PCS
3 Support legs with leveler 5 PCS
HARDWARE LIST: ICB-404
No. Description Sketch Quantity
A Bolt Ø5/16"*2-1/4" 8 PCS
B Lock Washer Ø5/16" 8 PCS
C Flat Washer Ø5/16" 8 PCS
D Allen Wrench 5mm 1 PC
HARDWARE LIST: ICB-406L/410L
No. Description Sketch Quantity
E Wood Screw 10 PCS
F Allen Wrench 4mm 1 PC
COMPONENTS LIST: ICB-406L/410L
No. Description Sketch Quantity
1 Bed rails 2 PCS
2 Slats 5 PCS
3 Magnetic Plate(Only for -410L) 4 PCS
COMPONENTS LIST: ICB-404
No. Description Sketch Quantity
1 Headboard 1 PC
2 Left Leg 1 PC
3 Right Leg 1 PC
4 Wood Stretcher 1 PC
ITEM NO: ICB-404-BCH/BLK/EGG/GRY-KD-1 King/Cal King Sleigh Bed HB
ICB-406L-BCH/BLK/EGG/GRY-1 King Side Rails
ICB-410L-BCH/BLK/EGG/GRY-1 Cal King Side Rails
ICB-405-BCH/BLK/EGG/GRY-1 King/Cal King Sleigh Bed FB
10-26-2017
10-26-2017
Page 2/4
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
STEP 3: Lay footboard back down on a padded, clean surface. Attach bun feet to footboard. Turn
footboard right side up.
Leveler
Bun Foot
b
a
Wood Screw
Slat bearer
Side Rail
HB Backside
Left Leg
Right Leg
STEP 1: Lay the headboard face down on a
soft surface. Attach the left leg and right leg
to headboard by using 6 bolts(A), lock
washers(B) and flat washers(C).
STEP 2: Attach the wood stretcher to the
legs by using 2 bolts(A), lock washers(B)
and flat washers(C).
HB Backside
Wood Stretcher
A
B
C
D
A
B
C
D
STEP 4: The slat bearers have been attached in position b. The slat bearers can be moved into
position a depending on the mattress/platform configuration. Remove the bolts and screws from
the slat bearers and side rails as shown below. Then re-attach the slat bearers to the side rails in
desired position with bolts, lock washers, flat washers, and screws. Caution: Do not over tighten
bolts as this may loosen the threaded inserts in the side rails.
ITEM NO: ICB-404-BCH/BLK/EGG/GRY-KD-1 King/Cal King Sleigh Bed HB
ICB-406L-BCH/BLK/EGG/GRY-1 King Side Rails
ICB-410L-BCH/BLK/EGG/GRY-1 Cal King Side Rails
ICB-405-BCH/BLK/EGG/GRY-1 King/Cal King Sleigh Bed FB
10-26-2017
Page 3/4
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
STEP 5: Hook the side rails to the headboard and footboard.
Headboard Slat bearer
The outside holes match to 6/6 bed rails,
the inside holes match to 6/0 bed rails.
Side Rail
Side Rail
Side Rail
STEP 7: Attach the support legs with leveler to the
slats. Adjust the levelers on bottom of support legs
when necessary. Support Leg
Leveler
This End Up
Slat
STEP 6: For Cal King bed, use magnetic plate to cover the
exposed hooks on headboard and footboard. For regular
King bed, skip this step. Magnetic Plate
ITEM NO: ICB-404-BCH/BLK/EGG/GRY-KD-1 King/Cal King Sleigh Bed HB
ICB-406L-BCH/BLK/EGG/GRY-1 King Side Rails
ICB-410L-BCH/BLK/EGG/GRY-1 Cal King Side Rails
ICB-405-BCH/BLK/EGG/GRY-1 King/Cal King Sleigh Bed FB
10-26-2017
Page 4/4
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
STEP 8: Arrange the slats on the slat
bearers equally and attach to the slat
bearers with wood screws (E).
Wood Screws (E)
FUNCTIONALITY INSTRUCTION ICB-404
ICB-406L
ICB-404
ICB-410L ICB-405
ICB-405
ITEM NO: ICB-404-BCH/BLK/EGG/GRY-KD-1 King/Cal King Sleigh Bed HB
ICB-406L-BCH/BLK/EGG/GRY-1 King Side Rails
ICB-410L-BCH/BLK/EGG/GRY-1 Cal King Side Rails
ICB-405-BCH/BLK/EGG/GRY-1 King/Cal King Sleigh Bed FB
1 Powered USB Port for
Charging on both sides
1 Powered USB Port for
Charging on both sides
10-26-2017
Page 1/7
Thank you for purchasing this quality product. Be sure to check all packing material carefully for
small parts that may come loose inside the carton during shipment.
UNIT SHOULD BE INSTALLED BY 2 OR MORE PERSONS.
BEFORE USING THIS PRODUCT PLEASE READ, UNDERSTAND, AND FOLLOW THESE INSTRUCTIONS.
Save these instructions for future reference.
All Beds need to be set up in the exact final
location so that after full assembly it will not
need to be moved. Moving the bed will cause
the support legs to move out of perpendicular
(90 degree), weaken the support system, and
may allow the bed to collapse.
FOR INDOOR USE ONLY
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ICB-407D
ICB-410L
ICB-406L
ICB-415
ICB-404
ICB-406L
ICB-407D
ICB-410L
OPTION 2: King/Cal King Storage Panel Bed
OPTION 1: King/Cal king Storage Sleigh Bed
ITEM NO: ICB-404-BCH/BLK/EGG/GRY-KD-1 King/Cal King Sleigh Bed HB
ICB-406L-BCH/BLK/EGG/GRY-1 King Side Rails
ICB-410L-BCH/BLK/EGG/GRY-1 Cal King Side Rails
ICB-407D-BCH/BLK/EGG/GRY-1 King/Cal King LP FB w/Drawers
ICB-415-BCH/BLK/EGG/GRY-KD King/Cal King Panel HB
10-26-2017
Page 2/7
COMPONENTS LIST: ICB-415
No. Description Sketch Quantity
1 Headboard 1 PC
2 Left Leg 1 PC
3 Right Leg 1 PC
4 Wood Stretcher 1 PC
TOOLS REQUIRED (NOT PROVIDED)
PHILLIPS SCREWDRIVER
UTILITY KNIFE (FOR CAL KING)
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
HARDWARE LIST: ICB-415
No. Description Sketch Quantity
N Bolt Ø5/16"*1-3/4" 10 PCS
O Lock Washer Ø5/16" 10 PCS
P Flat Washer Ø5/16" 10 PCS
Q Allen Wrench 5mm 1 PC
HARDWARE LIST: ICB-407D
No. Description Sketch Quantity
G Bolt Ø1/4"*1-3/4" 9 PCS
H Bolt Ø1/4"*1-1/4" 4 PCS
I Lock Washer Ø1/4" 13 PCS
J Flat washer Ø1/4" 13 PCS
K Wood Screw #8*1" 6 PCS
LWood Screw #8*1-1/2" 5 PCS
M Allen Wrench 4mm 1 PC
COMPONENTS LIST: ICB-406L/410L
No. Description Sketch Quantity
1 Bed rails 2 PCS
2 Slats 5 PCS
3 Magnetic Plate(Only for -410L) 4 PCS
COMPONENTS LIST: ICB-407D
No. Description Sketch Quantity
1 Footboard 1 PC
2 Support Leg (for center rail) 1 PC
3 Support Leg (for pedestal) 2 PCS
4 Decking 3 PCS
5 Center Rail 1 PC
6 Filler 1 PC
7 Bun Foot 2 PCS
8 Support Panel 2 PCS
9 Rail connector 1 PC
COMPONENTS LIST: ICB-404
No. Description Sketch Quantity
1 Headboard 1 PC
2 Left Leg 1 PC
3 Right Leg 1 PC
4 Wood Stretcher 1 PC
HARDWARE LIST: ICB-404
No. Description Sketch Quantity
A Bolt Ø5/16"*2-1/4" 8 PCS
B Lock Washer Ø5/16" 8 PCS
C Flat Washer Ø5/16" 8 PCS
D Allen Wrench 5mm 1 PC
HARDWARE LIST: ICB-406L/410L
No. Description Sketch Quantity
E Wood Screw 10 PCS
F Allen Wrench 4mm 1 PC
ITEM NO: ICB-404-BCH/BLK/EGG/GRY-KD-1 King/Cal King Sleigh Bed HB
ICB-406L-BCH/BLK/EGG/GRY-1 King Side Rails
ICB-410L-BCH/BLK/EGG/GRY-1 Cal King Side Rails
ICB-407D-BCH/BLK/EGG/GRY-1 King/Cal King LP FB w/Drawers
ICB-415-BCH/BLK/EGG/GRY-KD King/Cal King Panel HB
10-26-2017
Page 3/7
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
HB Backside
Left Leg
Right Leg
OPTION 1: King/Cal king Storage Sleigh Bed
STEP 1: Lay the headboard face down on a
soft surface. Attach the left leg and right leg
to headboard by using 6 bolts(A), lock
washers(B) and flat washers(C).
STEP 2: Attach the wood stretcher to the
legs by using 2 bolts(A), lock washers(B)
and flat washers(C).
HB Backside
Wood Stretcher
STEP 3: Lay footboard upside down on a padded, clean surface. Attach support legs (for pedestal)
and bun feet to footboard using 4 bolts(H), lock washers(I) and flat washers(J). Turn footboard
right side up.
Leveler
Bun Foot
H
I
J
M
A
B
C
D
A
B
C
D
ITEM NO: ICB-404-BCH/BLK/EGG/GRY-KD-1 King/Cal King Sleigh Bed HB
ICB-406L-BCH/BLK/EGG/GRY-1 King Side Rails
ICB-410L-BCH/BLK/EGG/GRY-1 Cal King Side Rails
ICB-407D-BCH/BLK/EGG/GRY-1 King/Cal King LP FB w/Drawers
ICB-415-BCH/BLK/EGG/GRY-KD King/Cal King Panel HB
10-26-2017
Page 4/7
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
STEP 5: Hook the side rails to the headboard and footboard, Attach support leg and center rail to
headboard and footboard by using 5 wood screws(L).
Headboard
Slat bearer
The outside holes match to 6/6 bed rails,
the inside holes match to 6/0 bed rails.
Side Rail
Side Rail
Side Rail
STEP 4: Attach support leg and support panels to center rail by using 6 bolts(G), lock washers(I)
and flat washers(J).
Support Panel
Support Leg (for center rail)
Center Rail
G
I
J
GIJ Rail connector
Center Rail
To Cal King bed, attach rail
connector to the support rail first.
L
L
M
ITEM NO: ICB-404-BCH/BLK/EGG/GRY-KD-1 King/Cal King Sleigh Bed HB
ICB-406L-BCH/BLK/EGG/GRY-1 King Side Rails
ICB-410L-BCH/BLK/EGG/GRY-1 Cal King Side Rails
ICB-407D-BCH/BLK/EGG/GRY-1 King/Cal King LP FB w/Drawers
ICB-415-BCH/BLK/EGG/GRY-KD King/Cal King Panel HB
10-26-2017
Page 5/7
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
STEP 6: Arrange slats on the
slat bearers and then lay the
decking on top of the slats.
Make sure the top and
bottom slats are situated
underneath the pre-drilled
holes as shown below in
STEP 8. Remove the
decking and attach slats to
the slat bearers with wood
screws (E).
Wood Screws (E)
Filler Notch
STEP 8: Put the decking over the slats, secure decking to the slats with wood screws (K) through
the pre-drilled holes in the decking as shown below.
Decking Decking Decking Decking Decking Decking
Filler
Filler
Make sure that there is a slat
under the pre-drilled hole.
K
Decking
Pre-drilled hole
STEP 9: For Cal King bed, use magnetic plate to
cover the exposed hooks on headboard and
footboard. For regular King bed, skip this step. Magnetic Plate
STEP 7: For Cal King bed, use a utility knife to cut off the small
piece at the notch on the Decking Filler piece included with the
Storage Footboard. For regular King bed, skip this step.
Cal King bed
King bed
ITEM NO: ICB-404-BCH/BLK/EGG/GRY-KD-1 King/Cal King Sleigh Bed HB
ICB-406L-BCH/BLK/EGG/GRY-1 King Side Rails
ICB-410L-BCH/BLK/EGG/GRY-1 Cal King Side Rails
ICB-407D-BCH/BLK/EGG/GRY-1 King/Cal King LP FB w/Drawers
ICB-415-BCH/BLK/EGG/GRY-KD King/Cal King Panel HB
FUNCTIONALITY INSTRUCTION
ICB-407D
ICB-406L
ICB-415
10-26-2017
Page 6/7
aspenhome RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
STEP 1: Lay the headboard face down on a
soft surface. Attach the left leg and right leg
to headboard by using 8 bolts(N), lock
washers(O) and flat washers(P).
STEP 2: Attach the wood stretcher to the
legs by using 2 bolts(N), lock washers(O)
and flat washers(P).
HB Backside
Left Leg
Right Leg
STEP 3 to STEP 9 are same as OPTION 1
OPTION 2: King/Cal king Storage Panel Bed
OP
Q
ICB-407D
ICB-410L
ICB-415
O
P
Q
N
N
Wood Stretcher
HB Backside
ITEM NO: ICB-404-BCH/BLK/EGG/GRY-KD-1 King/Cal King Sleigh Bed HB
ICB-406L-BCH/BLK/EGG/GRY-1 King Side Rails
ICB-410L-BCH/BLK/EGG/GRY-1 Cal King Side Rails
ICB-407D-BCH/BLK/EGG/GRY-1 King/Cal King LP FB w/Drawers
ICB-415-BCH/BLK/EGG/GRY-KD King/Cal King Panel HB
Page is loading ...
/
