Spectrum Industries Aspire Workstation Owner's manual

Spectrum Industries
Brand
Spectrum Industries
Model
Aspire Workstation
Category
Multimedia carts & stands
Type
Owner's manual
Assembly Instructions
0193938 Page 1 of 3
Assembly Instructions
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts or
accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Aspire Workstation
55569
(1) 0176803
Top channel
(4) 0105662
60mm 5/16-18 x 1”
Stem Caster
(37) 035594
#10 x 5/8”
PHSM
(2) 0176618
Leg insert panel
1
/
2”
Assembly tip: Do not tighten component fasteners completely
until all have been installed. Keeping them loose will help with
alignment between parts during assembly.
(2) 039622
2” grommet
with cover
(2) 059984
2” grommet
(2) 0176590
Leg
(1) 0176747
Base panel
(1) 0176901
Worksurface
(1) 0176855
Worksurface
support bracket
(1) 0176631
Audience-side
panel
(2) 0176749
Shelf
Attach casters to legs
1. Attach casters to legs and tighten.
1
X4
Leg
0193938 Page 2 of 3
1. Place the worksurface face-down onto a non-abrasive surface.
2. Orient the legs as shown with the ange toward the center.
3. Attach each leg to the worksurface with (3) screws.
Attach worksurface support bracket
1. Attach the support bracket to the worksurface with (3) screws.
4
Install leg insert panels
1. Set an insert panel into each leg and attach each
with (2) screws in the center holes only.
3
Attach legs to worksurface
2
Leg
Leg
Worksurface
(3) #10 x 5/8”
PHSM screws
(3) #10 x 5/8”
PHSM screws
Attach base panel
1. Attach the base panel to the legs with (4) screws (2 per leg).
2. Secure each insert panel at the worksurface with the (2) additional
screws shown.
5
Leg insert panel
Leg insert panel
(2) #10 x 5/8”
PHSM screws in
center holes only
Base panel
Worksurface
Worksurface
Worksurface
support bracket
(3) #10 x 5/8”
PHSM screws
(2) screws in
center holes only
(4) #10 x 5/8”
PHSM screws
(2) #10 x 5/8”
PHSM screws
0193938 Page 3 of 3
© 2023 Spectrum Industries Inc., All rights reserved.
1500 RIVER STREET, PO BOX 400, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
Attach audience-side panel
1. Attach audience-side panel to the legs with (6) screws.
7
Attach top channel
1. Orient the top channel as shown and secure with (4) screws.
(2 into worksurface, 1 into each leg).
6
Install adjustable shelves
1. Carefully ip the lectern upright. This may take 2 people.
2. Install screws and shelves at the desired shelf heights. (4 screws per shelf).
8
Install grommets
1. Install grommets in shelves and side panels.
9
2” grommet
with cover
(1 per side)
2” grommet
(3 total)
Top channel
Worksurface
Shelves
Audience-side panel
Note: If installing the 95044 optional locking door, the lower shelf will need
to be installed using the 3rd set of mounting holes from the bottom.
(2) #10 x 5/8”
PHSM screws
(2) #10 x 5/8”
PHSM screws
(6) #10 x 5/8”
PHSM screws
  • Page 1 1
  • Page 2 2
  • Page 3 3

Spectrum Industries Aspire Workstation Owner's manual

Spectrum Industries
Brand
Spectrum Industries
Model
Aspire Workstation
Category
Multimedia carts & stands
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents