Crestron TST-600-DSW-BB
Wall Mount Back Box for TST-600-DSW
Installation Guide
Regulatory Compliance
This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
As of the date of manufacture, the TST-600-DSW-BB has been tested and found to comply with
specifications for CE marking.
Product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries.
Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or
their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or
photography.
This document was written by the Technical Publications department at Crestron.
©2014 Crestron Electronics, Inc.
Crestron TST-600-DSW-BB Wall Mount Back Box for TST-600-DSW
Contents
Wall Mount Back Box for TST-600-DSW: TST-600-DSW-BB 1
Description ................................................................................................................................. 1
Setup .......................................................................................................................................... 5
Supplied Hardware ...................................................................................................... 5
Assembly ..................................................................................................................... 5
Mounting ..................................................................................................................... 5
Installation ................................................................................................................... 8
Other Mounting Option Accessories ........................................................................... 8
Resources ................................................................................................................................... 9
Reference Documents .................................................................................................. 9
Further Inquiries .......................................................................................................... 9
Future Updates ............................................................................................................ 9
Installation Guide – DOC. 7455B Contents • i
Crestron TST-600-DSW-BB Wall Mount Back Box for TST-600-DSW
Wall Mount Back Box
for TST-600-DSW:
TST-600-DSW-BB
Description
The TST-600-DSW-BB provides a UL
®
-listed, recess wall-mounted metal back box
for the Crestron
®
TST-600-DSW Wall Mount Docking Station and the
TST-600-WALL and TST-602-WALL Wall Mount Wireless Touch Screens.
Designed for pre-construction applications, the TST-600-DSW-BB permits fastening
to a stud in a framed wall prior to installation of drywall. Conduit knockouts are
provided on the top and bottom. A blank cover plate is included to provide a
temporary cover for the opening during construction.
NOTE: If mounting in a material other than drywall (for example, wood lectern,
concrete or rock) use the cutout template, available in the post-construction kit
TST-600-DSW-MMK or TST-600-DSW-TMK.
NOTE: For concrete and rock mounting material, allow for proper ventilation
before mounting the TST-600-DSW.
Installation Guide – DOC. 7455B Wall Mount Back Box for TST-600-DSW: TST-600-DSW-BB • 1
Wall Mount Back Box for TST-600-DSW Crestron TST-600-DSW-BB
The mounted view of the TST-600-DSW-BB is shown in the following illustration.
TST-600-DSW-BB Mounted View (Optional Cover Plate Attached)
2 • Wall Mount Back Box for TST-600-DSW: TST-600-DSW-BB Installation Guide – DOC. 7455B
Crestron TST-600-DSW-BB Wall Mount Back Box for TST-600-DSW
The dimensions of the TST-600-DSW-BB are shown in the following illustrations.
TST-600-DSW-BB Overall Dimensions (Front View)
12.00 in
(305 mm)
6.35 in
(162 mm)
8.00 in
(204 mm)
8.88 in
(226 mm)
9.06 in
(231 mm)
5 in
(127 mm)
6 3/4 in
(171 mm)
6 in
(152 mm)
9 in
(227 mm)
7 3/4 in
(197 mm)
6 1/4 in
(158 mm)
6 3/16 in
(155 mm)
5 7/8 in
(148 mm)
Installation Guide – DOC. 7455B Wall Mount Back Box for TST-600-DSW: TST-600-DSW-BB • 3
Wall Mount Back Box for TST-600-DSW Crestron TST-600-DSW-BB
TST-600-DSW-BB Overall Dimensions (Bottom View)
10.50 in
(267 mm)
3.31 in
(85 mm)
3.25 in
(83 mm)
1.50 in
(39 mm)
NOTE: Knockout holes are intended for Class 2 wiring only and are 1/2” (13 mm)
and 3/4” (19 mm) diameter.
TST-600-DSW-BB Overall Dimensions (Cover Plate)
9.85 in
(251 mm)
7.00 in
(178 mm)
0.03 in
(1 mm)
4 • Wall Mount Back Box for TST-600-DSW: TST-600-DSW-BB Installation Guide – DOC. 7455B
Crestron TST-600-DSW-BB Wall Mount Back Box for TST-600-DSW
Setup
Supplied Hardware
The hardware supplied with the TST-600-DSW-BB is listed in the following table.
Supplied Hardware for the TST-600-DSW-BB
DESCRIPTION PART NUMBER QUANTITY
Assembly, Wall Mount, Back Box 4507462 1
Metal, Plate, Blank, Cover 2022825 1
Screw, #06-32 x 1 1/2”, Pan, Phil 2007254 4
Screw, #08-8B, 1/4”, Pan, Phil 2007277 1
Assembly
Required Tools:
• #2 Phillips tip screwdriver
The back box mounting enclosure comes fully assembled except for a grounding
screw. To prepare for mounting, complete the following procedure:
1. Remove knockouts as required.
2. Attach the supplied #08-8B self-tapping screw (2007277) to back box
mounting enclosure assembly for grounding.
NOTE: The #08-8B self-tapping screw (2007277), supplied for grounding
purposes, is installed in the rear of the back box mounting enclosure assembly.
Mounting
Required Tools and Materials:
• #2 Phillips tip screwdriver
• Level
• Standard drywall screws or nails (not included)
CAUTION: Allow an air gap of at least 12 inches (305 mm) in the wall cavity
above and below the TST-600-DSW for heat dissipation.
NOTE: If the installation is not on wooden studs, be sure to consider the needs of
the particular situation. For example, screw type may vary for steel studs.
To mount the back box, complete the following procedure (refer to illustration on the
following page).
1. Position the back box against the stud so the extended edge of the attached
mounting plate covers the front edge of the stud. Ensure the side of the back
box is also against the side of the stud.
Installation Guide – DOC. 7455B Wall Mount Back Box for TST-600-DSW: TST-600-DSW-BB • 5
Wall Mount Back Box for TST-600-DSW Crestron TST-600-DSW-BB
2. Use the level and verify the back box is horizontal. Leveling must be done
before proceeding.
3. Attach the back box to the left or right side of the stud with standard
drywall screws or nails (not included). If mounting to the left side of a stud,
the back box must be turned over so the extended edge of the attached
mounting plate is on the right side.
4. Feed cables through the knockout holes.
NOTE: This assembly should use Class 2 wiring only.
Mounting the Back Box
Ensure these
surfaces
are flush.
Back Box Mounting
Enclosure Assembly
(4507462)
NOTE: Ensure the
assembly is level
when mounted.
Screw (1) #08-8B x 1/4”
Self-Tapping
for Grounding
(2007277)
6 • Wall Mount Back Box for TST-600-DSW: TST-600-DSW-BB Installation Guide – DOC. 7455B
Crestron TST-600-DSW-BB Wall Mount Back Box for TST-600-DSW
Mounted View with Cover Plate (Mounting Example Prior to Drywall Installation)
NOTE: Back box is to be covered with
drywall and then the cutout made around
the inside of the opening.
Be sure to leave the four tapped holes
on the front of the box exposed to
accept the mounting screws.
Cover Plate (2022825)
to cover cutout in drywall
before TST-600-DSW is installed
(may be required by local building codes)
Screws (4) #06-32 x 1 1/2”
(2007254)
NOTE: Cut the drywall to the inside edge of the front of the back box. The labels
on the front of the back box indicate the perimeter of the opening that should be cut
out.
NOTE: The four tapped holes on the front of the back box must be exposed to
accept the TST-600-DSW mounting screws. These holes are found along the top and
bottom of the opening made by cutting out the drywall. Refer to NOTE in the
illustration above.
Installation Guide – DOC. 7455B Wall Mount Back Box for TST-600-DSW: TST-600-DSW-BB • 7
Wall Mount Back Box for TST-600-DSW Crestron TST-600-DSW-BB
Installation
Complete the installation by either installing the TST-600-DSW, leaving the hole
open (if permitted by local building codes) or installing the optional cover plate with
the included #06-32 x 1 1/2” screws. If the TST-600-DSW is to be installed, refer to
the latest version of the TST-600-DSW Operations & Installation Guide (Doc. 7434)
for installation instructions. The document is available at
www.crestron.com/manuals
. Refer also to the following comprehensive illustration.
TST-600-DSW Mounting (Exploded View)
TST-600-DSW
Drywall
TST-600-DSW-BB
Screws (4) #06-32 x 1 1/2”
(2007254)
Other Mounting Option Accessories
If too much of the mounting plate is exposed after the drywall is cut, the area may
need to be patched. Crestron provides the following accessories:
• TST-600-DSW-TMK (Doc. 7456): for smaller repairs and to provide a
smooth edge at the opening. This option provides a finished appearance and
is preferred when wallpaper is hung.
• TST-600-DSW-MMK (Doc. 7457): for larger repairs and to fill in larger
irregularities around the opening (requires plastering).
The manuals for the TST-600-DSW-MMK and TST-600-DSW-TMK are available
at www.crestron.com/manuals
.
8 • Wall Mount Back Box for TST-600-DSW: TST-600-DSW-BB Installation Guide – DOC. 7455B
Crestron TST-600-DSW-BB Wall Mount Back Box for TST-600-DSW
Resources
Reference Documents
All documents mentioned in this guide are available at www.crestron.com/manuals.
List of Related Reference Documents
DOCUMENT TITLE
TST-600-DSW Wall Mount Docking Station for TST-600
TST-600-DSW-MMK & TST-600-DSW-WMKM Mud Mount Kits for TST-600-DSW
TST-600-DSW-TTK & TST-600-DSW-WMKT Trim Ring Kits for TST-600-DSW
Further Inquiries
To locate specific information or resolve questions after reviewing this guide,
contact Crestron's True Blue Support at 1-888-CRESTRON [1-888-273-7876] or, for
assistance within a particular geographic region, refer to the listing of Crestron
worldwide offices at www.crestron.com/offices
.
To post a question about Crestron products, log onto Crestron’s Online Help at
www.crestron.com/onlinehelp
. First-time users must establish a user account to fully
benefit from all available features.
Future Updates
As Crestron improves functions, adds new features, and extends the capabilities of
the TST-600-DSW-BB, additional information may be made available as manual
updates. These updates are solely electronic and serve as intermediary supplements
prior to the release of a complete technical documentation revision.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
Installation Guide – DOC. 7455B Wall Mount Back Box for TST-600-DSW: TST-600-DSW-BB • 9
Wall Mount Back Box for TST-600-DSW Crestron TST-600-DSW-BB
This page is intentionally left blank.
10 • Wall Mount Back Box for TST-600-DSW: TST-600-DSW-BB Installation Guide – DOC. 7455B
Crestron TST-600-DSW-BB Wall Mount Back Box for TST-600-DSW
This page is intentionally left blank.
Installation Guide – DOC. 7455B Wall Mount Back Box for TST-600-DSW: TST-600-DSW-BB • 11
Crestron Electronics, Inc. Installation Guide – DOC. 7455B
15 Volvo Drive Rockleigh, NJ 07647 (2035129)
Tel: 888.CRESTRON 12.14
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.
/
