Dwyer Series DHII User manual

Dwyer
Brand
Dwyer
Model
Series DHII
Category
Measuring, testing & control
Type
User manual
Bulletin B-31
Series DHII Digihelic
®
II Differential Pressure Controller
Specifications - Installation and Operating Instructions
DWYER INSTRUMENTS, INC.
Phone: 219/879-8000 www.dwyer-inst.com
P.O. BOX 373 • MICHIGAN CITY, IN 46360, U.S.A. Fax: 219/872-9057 e-mail: [email protected]
DO NOT REMOVE
THESE SCREWS
T
O GAIN ACCESS TO WIRING TERMINALS,
REMOVE THESE TWO SCREWS AND “FLIP” DISPLAY
90° DO NOT REMOVE THE SCREWS WITH]
POWER APPLIED TO INSTRUMENT
HINGED
STANDOFF
WIRING
TERMINALS
1
DIMENSIONS
4-23/32
[120]
1
-31/64
[
37.62]
3-7/16
[87.12]
1
-45/64
[
43.18]
1-17/32
[38.61]
4-23/32
[120]
45/64
[17.78]
1-1/16
[26.97]
1-7/8
[47.5]
1-45/64
[43.18]
1-1/2
[38.35]
2
-23/64
[
59.94]
4X Ø3/16 [4.76]
CLEARANCE
HOLES FOR
MOUNTING
MOUNTING HOLE
PATTERN
1-5/16
[33]
3-17/64
[83]
4-1/8
[105]
WIRING TERMINAL ACCESS
4-23/32
[120]
3-7/16
[87.12]
1-45/64
[43.18]
1-17/32
[38.61]
4-23/32
[120]
45/64
[17.78]
4X Ø3/16 [4.76]
CLEARANCE
HOLES FOR
MOUNTING
MOUNTING HOLE
PATTERN
1-5/16
[33]
1-15/16
[48.97]
25/32
[21.18]
2-31/32
[75.39]
1-5/32
[29.59]
4-9/64
[105.17]
5-7/32
[132.54]
BRACKETS
ARE OPTIONAL
4-1/8
[105]
3-17/64
[83]
#8 LOCK
WASHER
#8-36 SLOTTED
MACHINE SCREW
OPTIONAL A-438 BRACKET
MOUNTING DIAGRAM
#8 LOCK
WASHER
8-36 FLAT HEAD
SCREWS
4-9/64
[105.17]
5-7/32
[132.56]
3-17/64
[83]
4-1/8
[105]
Bracket Assembly
2
SPECIFICATIONS
Service: Air and non-combustible, compatible gases.
Wetted Materials: Consult factory.
Housing Material: Aluminum, glass.
Accuracy: ±0.5% at 77°F (25°C) including hysteresis and repeatability (after 1 hour warm-up).
Stability: < ±1% per year.
Pressure Limits: Ranges ≤ 2.5 in. w.c. = 2 psi
5˝: 5 psi; 10˝: 5 psi; 25˝: 5 psi; 50˝: 5 psi; 100˝: 9 psi.
Temperature Limits: 32 to 140°F (0 to 60°C).
Compensated Temperature Limits: 32 to 140°F (0 to 60°C).
Thermal Effects: 0.020%/°F (0.036/°C) from 77°F (25°C).
Power Requirements:
High Voltage Power = 100 to 240 VAC, 50 to 400 Hz or 132 to 240 VDC;
Low Voltage Power = 24 VDC ±20%.
Power Consumption:
Low Voltage Power = 24 VDC - 130 mA max.
High Voltage Power = 100 to 240 VAC, 132 to 240 VDC - 7VA max.
Output Signal: 4-20 mA DC into 900 ohms max.
Zero & Span Adjustments: Accessible via menus.
Response Time: 250 ms (dampening set to 1).
Display: 4 digit backlit LCD 0.6˝ height. LED indicators for set point and alarm status.
Electrical Connections: Euro type removeable terminal blocks with watertight conduit fittings for
1/2˝ watertight conduit.
Process Connections: 1/8 female NPT.
Enclosure Rating: Designed to meet NEMA 4 (IP66).
Mounting Orientation: Mount unit in vertical plane.
Size: 4.73˝ x 4.73˝ x 3.43˝ (120 mm x 120 mm x 87.1 mm).
Weight: 2 lb 10 oz (1.19 kg).
Serial Communications: Modbus
®
RTU, RS485, 9600 Baud.
Agency Approvals: UL & CE.
SWITCH SPECIFICATIONS
Switch Type: 2 SPDT relays.
Electrical Rating: 8 Amps at 240 VAC resistive.
Set Point Adjustment: Adjustable via keypad on face.
Modbus
®
is a registered trademark of Schnieder Automation.
3
Notes:
1. The instrument may be powered from the AC line or 24 VDC. Do not wire AC line terminals 1-2 on
the lower board and 24 VDC terminals 4-5 on the upper board at the same time or damage to the
unit will result.
2. For supply connections, wire in accordance with an equivalent national standard or code. Use
copper conductors only rated for at least 75°C.
3. Terminals on upper board are rated CLASS 2.
4. ISOLATION:
Relays - 1500 VAC to all other inputs and outputs.
AC Line Power (terminals 4-5) - 1500 VAC to all other inputs and outputs.
RS485 output - 500 VAC to all other CLASS 2 wiring.
The 24 VDC Power, 4-20 mA transmitter, and Remote Reset Switch share a common
ground.
5. The Remote Reset Switch must be a dry contact switch.
6. Shielded cable is required for RS485 wiring.
WIRING
WARNING
If Digihelic
®
II Controller is powered by 24 VDC, the device receiving the 4-20 mA
transmitter output MUST NOT share a common ground with the 24 VDC supply or
damage to the Digihelic
®
II Controller will result.
m
11 212312341234
5
1234
5
6
1234
5
6
7
1234
5
6
7
8
1234
5
6
7
8
11
2
1
2
3
1
2
34
1
2
345
1
2
3456
1
2
3456
71
2
3456
7
8
1
2
3456
7
8
CONNECTOR
1
2
3456
7
8
C
1
2
3456
7
8
CO
1
2
3456
7
8
CON
1
2
3456
7
8
CONN
1
2
3456
7
8
CONNE
1
2
3456
7
8
CONNEC
1
2
3456
7
8
CONNECT
1
2
3456
7
8
CONNECTO
1
2
3456
7
8
CONNECTOR ON
1
2
3456
7
8
CONNECTOR O
1
2
3456
7
8
CONNECTOR ON
LOWER
1
2
3456
7
8
CONNECTOR ON
L
1
2
3456
7
8
CONNECTOR ON
LO
1
2
3456
7
8
CONNECTOR ON
LOW
1
2
3456
7
8
CONNECTOR ON
LOWE
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
1
2
3456
7
8
CONNECTOR ON
LOWER B
1
2
3456
7
8
CONNECTOR ON
LOWER BO
1
2
3456
7
8
CONNECTOR ON
LOWER BOA
1
2
3456
7
8
CONNECTOR ON
LOWER BOAR
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTOR
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
C
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CO
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CON
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONN
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNE
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNEC
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECT
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTO
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTOR ON
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTOR O
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTOR ON
UPPER
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTOR ON
U
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTOR ON
UP
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTOR ON
UPP
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTOR ON
UPPE
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTOR ON
UPPER BOARD
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTOR ON
UPPER B
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTOR ON
UPPER BO
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTOR ON
UPPER BOA
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTOR ON
UPPER BOAR
1
2
3456
7
8
CONNECTOR ON
LOWER BOARD
CONNECTOR ON
UPPER BOARD
1
00-240110100100-100-2100-24100-240 VAC100-240V100-240VA100-240VACor100-240VACo100-240VACor
132-240
100-24
0VACor
1
100-240 VAC or
13
100-24
0VACor
132
100-24
0VACor
132-
100-24
0VACor
132-2
100-24
0VACor
132-24
100-24
0VACor
132-240 VDC
100-24
0VACor
132-240 V
100-24
0VACor
132-240 VD
100-24
0VACor
132-240 VDC POWER
100-24
0VACor
132-240 VDC P
100-24
0VACor
132-240 VDC PO
100-24
0VACor
132-240 VDC POW
100-24
0VACor
132-240 VDC POWE
100-24
0VACor
132-240 VDC POWER
NOTE
100-24
0VACor
132-240 VDC POWER
N
100-24
0VACor
132-240 VDC POWER
NO
100-24
0VACor
132-240 VDC POWER
NOT
100-24
0VACor
132-240 VDC POWER
NOTE 1
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8
100-24
0VACor
132-240 VDC POWER
NOTE 1
3
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250vac
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 2
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 25
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250v
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250va
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250vac
MEDIUM
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250vac
M
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250vac
ME
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250vac
MED
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250vac
MEDI
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250vac
MEDIU
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250vac
MEDIUM LAG
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250vac
MEDIUM L
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250vac
MEDIUM LA
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250vac
MEDIUM LAG
N
/C
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250vac
MEDIUM LAG
N
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250vac
MEDIUM LAG
N/
100-24
0VACor
132-240 VDC POWER
NOTE 1
3/8 A 250vac
MEDIUM LAG
N/C
N/CNN/N/C
N/ONN/N/O
N/ONN/N/O
CC
C
C
SP1SSPSP1
RELAY
SP1
R
SP1
RE
SP1
REL
SP1
RELA
SP1
RELAY
SP2
SP1
RELAY
S
SP1
RELAY
SP
SP1
RELAY
SP2 OR
SP1
RELAY
SP2 O
SP1
RELAY
SP2 OR
ALARM
SP1
RELAY
SP2 OR
A
SP1
RELAY
SP2 OR
AL
SP1
RELAY
SP2 OR
ALA
SP1
RELAY
SP2 OR
ALAR
SP1
RELAY
SP2 OR
ALARM
RELAY
SP1
RELAY
SP2 OR
ALARM
R
SP1
RELAY
SP2 OR
ALARM
RE
SP1
RELAY
SP2 OR
ALARM
REL
SP1
RELAY
SP2 OR
ALARM
RELA
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
SP1
RELAY
SP2 OR
ALARM
RELAY
A
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
R
S485
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
R
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS4
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS485
SERIAL
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5S
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SE
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SER
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERI
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIA
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIAL
COMMUNICATION
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIAL
C
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIAL
CO
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIAL
COM
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIAL
COMM
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIAL
COMMU
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIAL
COMMUN
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIAL
COMMUNI
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIAL
COMMUNIC
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIAL
COMMUNICA
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIAL
COMMUNICAT
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIAL
COMMUNICATI
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIAL
COMMUNICATIO
SP1
RELAY
SP2 OR
ALARM
RELAY
A-
B+
RS48
5SERIAL
COMMUNICATION
++
-
+
-
24
+
-
2
+
-
24 VDC
+
-
24 V
+
-
24 VD
+
-
24 VDC POWER
+
-
24 VDC P
+
-
24 VDC PO
+
-
24 VDC POW
+
-
24 VDC POWE
+
-
24 VDC POWER
NOTE
+
-
24 VDC POWER
N
+
-
24 VDC POWER
NO
+
-
24 VDC POWER
NOT
+
-
24 VDC POWER
NOTE 1
+
-
24 VDC POWER
NOTE 1
R
EMOTERREREMREMOREMOTREMOTE RESE TREMOTE RREMOTE REREMOTE RESREMOTE RESEREMOTE RESET
SWITCH
REM
OTE RESET
S
REMOTE RESET
SW
REM
OTE RESET
SWI
REM
OTE RESET
SWIT
REM
OTE RESET
SWITC
REM
OTE RESET
SWITCH
Device
REM
OTE RESET
SWITCH
D
REM
OTE RESET
SWITCH
De
REM
OTE RESET
SWITCH
Dev
REM
OTE RESET
SWITCH
Devi
REM
OTE RESET
SWITCH
Devic
REM
OTE RESET
SWITCH
Device receiving
REM
OTE RESET
SWITCH
Device r
REM
OTE RESET
SWITCH
Device re
REM
OTE RESET
SWITCH
Device rec
REM
OTE RESET
SWITCH
Device rece
REM
OTE RESET
SWITCH
Device recei
REM
OTE RESET
SWITCH
Device receiv
REM
OTE RESET
SWITCH
Device receivi
REM
OTE RESET
SWITCH
Device receivin
REM
OTE RESET
SWITCH
Device receiving 4-20mA
REM
OTE RESET
SWITCH
Device receiving 4
REM
OTE RESET
SWITCH
Device receiving 4-
REM
OTE RESET
SWITCH
Device receiving 4-2
REM
OTE RESET
SWITCH
Device receiving 4-20
REM
OTE RESET
SWITCH
Device receiving 4-20m
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal.
REM
OTE RESET
SWITCH
Device receiving 4-20mA
s
REM
OTE RESET
SWITCH
Device receiving 4-20mA
si
REM
OTE RESET
SWITCH
Device receiving 4-20mA
sig
REM
OTE RESET
SWITCH
Device receiving 4-20mA
sign
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signa
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. C
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Ch
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Che
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Chec
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check s
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check sp
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check spe
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check spec
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check speci
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check speci
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specic
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specica
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specicat
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specicati
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specicatio
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specication
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
o
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of t
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of th
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of thi
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this d
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this de
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this dev
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this devi
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this devic
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device f
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device fo
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for i
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for in
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for inp
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for inpu
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input l
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input lo
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input loa
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance.
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
r
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
re
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
res
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resi
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resis
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resist
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resista
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistan
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistanc
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. T
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Ty
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typ
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typi
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typic
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typica
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 2
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 25
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 t
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
6
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
60
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS,
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 O
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OH
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHM
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 900
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 9
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 90
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 900 OHMS
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 900 O
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 900 OH
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 900 OHM
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 900 OHMS
maximum.
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 900 OHMS
m
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 900 OHMS
ma
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 900 OHMS
max
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 900 OHMS
maxi
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 900 OHMS
maxim
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 900 OHMS
maximu
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 900 OHMS
maximum
REM
OTE RESET
SWITCH
Device receiving 4-20mA
signal. Check specications
of this device for input load
resistance. Typical 250 to
600 OHMS, 900 OHMS
maximum.
++
-
+
-
4-20mA44-4-24-204-20m4-20mA
TRANSMITTER
4-20mA
T
4-20mA
TR
4-20mA
TRA
4-20mA
TRAN
4-20mA
TRANS
4-20mA
TRANSM
4-20mA
TRANSMI
4-20mA
TRANSMIT
4-20mA
TRANSMITT
4-20mA
TRANSMITTE
4-20mA
TRANSMITTER
O
UTPUT
4-20mA
TRANSMITTER
O
4-20mA
TRANSMITTER
OU
4-20mA
TRANSMITTER
OUT
4-20mA
TRANSMITTER
OUTP
4-20mA
TRANSMITTER
OUTPU
4-20mA
TRANSMITTER
OUTPUT
4
When wiring the instrument, you must follow industry standard practice for control and
protection against Electro-Static Discharge (ESD). Failure to exercise good ESD practices
may cause damage to the control.
WIRING
1. Remove cover.
2. To gain access to the wiring terminal blocks, remove the upper and lower screws toward the center
of the display board, and then flip the display board up at a 90° angle.
3. Wire to the two terminals blocks as shown in the wiring diagram.
Note: Depending on the application, it may be only necessary to wire to the smaller terminal block on
the upper board. In that case one of the liquid tight fittings may be removed and replaced with the
provided rubber plug.
4. For liquid tight applications, use only 1/2˝ liquid tight conduit.
5. When wiring is complete, reverse steps 2 and 1. Make sure the cover is properly tightened to the
housing.
INSTALLATION
Mount the instrument in a location that will not be subject to excessive temperature, shock or vibration.
Pressure Connections
Use 1/8 male NPT fittings. When tightening fittings, grasp the brass fitting on the Digihelic
®
II Controller
with a 1/2˝ wrench to prevent the fitting on the Digihelic
®
II Controller from turning.
T
DIGIHELIC
®
II CONTROLLER RS485 WIRING
SHIELDSSHSHISHIESHIELSHIELD
SHIELD
SHIELD
S
SHIELD
SH
SHIELD
SHI
SHIELD
SHIE
SHIELD
SHIEL
SHIELD
SHIELD
TIETTITIE SHIELDTIESTIESHTIESHITIESHIETIESHIELTIESHIELD TOTIESHIELD TTIESHIELD TOEARTHTIESHIELD TOETIESHIELD TOEATIESHIELD TOEARTIESHIELD TOEARTTIESHIELD TOEARTH GROUNDTIESHIELD TOEARTH GTIESHIELD TOEARTH GRTIESHIELD TOEARTH GROTIESHIELD TOEARTH GROUTIESHIELD TOEARTH GROUNTIESHIELD TOEARTH GROUND
TOTTO RS232TORTORSTORS2TORS23TORS232 TOTORS232 TTORS232 TO
RS485
TO RS232 TO
R
TO RS232 TO
RS
TO RS232 TO
RS4
TO RS232 TO
RS48
TO RS232 TO
RS485 CONVERTER
TO RS232 TO
RS485 C
TO RS232 TO
RS485 CO
TO RS232 TO
RS485 CON
TO RS232 TO
RS485 CONV
TO RS232 TO
RS485 CONVE
TO RS232 TO
RS485 CONVER
TO RS232 TO
RS485 CONVERT
TO RS232 TO
RS485 CONVERTE
TO RS232 TO
RS485 CONVERTER
120112120 OHM120O120OH120OHM
RESISTOR
120 OHM
R
120 OHM
RE
120 OHM
RES
120 OHM
RESI
120 OHM
RESIS
120 OHM
RESIST
120 OHM
RESISTO
120 OHM
RESISTOR
LAST
120 OHM
RESISTOR
L
120 OHM
RESISTOR
LA
120 OHM
RESISTOR
LAS
120 OHM
RESISTOR
LAST UNIT
120 OHM
RESISTOR
LAST U
120 OHM
RESISTOR
LAST UN
120 OHM
RESISTOR
LAST UNI
120 OHM
RESISTOR
LAST UNIT ON
120 OHM
RESISTOR
LAST UNIT O
120 OHM
RESISTOR
LAST UNIT ON RS485
120 OHM
RESISTOR
LAST UNIT ON R
120 OHM
RESISTOR
LAST UNIT ON RS
120 OHM
RESISTOR
LAST UNIT ON RS4
120 OHM
RESISTOR
LAST UNIT ON RS48
120 OHM
RESISTOR
LAST UNIT ON RS485 BUSS
120 OHM
RESISTOR
LAST UNIT ON RS485 B
120 OHM
RESISTOR
LAST UNIT ON RS485 BU
120 OHM
RESISTOR
LAST UNIT ON RS485 BUS
120 OHM
RESISTOR
LAST UNIT ON RS485 BUSS
WIRE
120 OHM
RESISTOR
LAST UNIT ON RS485 BUSS
W
120 OHM
RESISTOR
LAST UNIT ON RS485 BUSS
WI
120 OHM
RESISTOR
LAST UNIT ON RS485 BUSS
WIR
120 OHM
RESISTOR
LAST UNIT ON RS485 BUSS
WIRE NUT
120 OHM
RESISTOR
LAST UNIT ON RS485 BUSS
WIRE N
120 OHM
RESISTOR
LAST UNIT ON RS485 BUSS
WIRE NU
120 OHM
RESISTOR
LAST UNIT ON RS485 BUSS
WIRE NUT
DIGIHELICDDIDIGDIGIDIGIHDIGIHEDIGIHELDIGIHELIDIGIHELIC -DIGIHELIC-RS485DIGIHELIC-RDIGIHELIC-RSDIGIHELIC-RS4DIGIHELIC-RS48DIGIHELIC-RS485WIRINGDIGIHELIC-RS485WDIGIHELIC-RS485WIDIGIHELIC-RS485WIRDIGIHELIC-RS485WIRIDIGIHELIC-RS485WIRINDIGIHELIC-RS485WIRINGTODIGIHELIC-RS485WIRINGTDIGIHELIC-RS485WIRINGTODAISYDIGIHELIC-RS485WIRINGTODDIGIHELIC-RS485WIRINGTODADIGIHELIC-RS485WIRINGTODAIDIGIHELIC-RS485WIRINGTODAISDIGIHELIC-RS485WIRINGTODAISYCHAINDIGIHELIC-RS485WIRINGTODAISYCDIGIHELIC-RS485WIRINGTODAISYCHDIGIHELIC-RS485WIRINGTODAISYCHADIGIHELIC-RS485WIRINGTODAISYCHAIDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTSDIGIHELIC-RS485WIRINGTODAISYCHAINIDIGIHELIC-RS485WIRINGTODAISYCHAININDIGIHELIC-RS485WIRINGTODAISYCHAININSDIGIHELIC-RS485WIRINGTODAISYCHAININSTDIGIHELIC-RS485WIRINGTODAISYCHAININSTRDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMEDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ONDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ODIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ONTHEDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ONTDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ONTHDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ONTHERS485DIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ONTHERDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ONTHERSDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ONTHERS4DIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ONTHERS48DIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ONTHERS485BUSSDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ONTHERS485BDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ONTHERS485BUDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ONTHERS485BUSDIGIHELIC-RS485WIRINGTODAISYCHAININSTRUMENTS ONTHERS485BUSS
UP
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
U
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP T
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 1
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 12
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 U
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UN
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNI
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNIT
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS M
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MA
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY B
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE D
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DA
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAI
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAIS
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY C
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CH
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHA
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAI
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAIN
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINE
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
T
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
TH
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 1
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 12
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 O
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OH
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM R
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RE
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RES
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESI
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESIS
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESIST
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTO
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
I
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS U
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS US
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USU
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUA
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUAL
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALL
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY O
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ON
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONL
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
N
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NE
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NEC
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECE
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECES
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESS
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSA
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSAR
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY F
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FO
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR LONG
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR L
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR LO
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR LON
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR LONG
WIRE
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR LONG
W
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR LONG
WI
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR LONG
WIR
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR LONG
WIRE RUNS.
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR LONG
WIRE R
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR LONG
WIRE RU
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR LONG
WIRE RUN
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR LONG
WIRE RUNS
DIGIHELIC - RS485 WIRING TO DAISY CHAIN INSTRUMENTS ON THE RS485 BUSS
UP TO 128 UNITS MAY BE DAISY CHAINED
THE 120 OHM RESISTOR
IS USUALLY ONLY
NECESSARY FOR LONG
WIRE RUNS.
11 212312341234
5
1234
5
6
1234
5
6
7
1234
5
6
7
8
1234
5
6
7
8
11
2
1
2
3
1
2
34
1
2
34
5
1
2
345
6
1
2
34
56
71
2
34
56
7
8
1
2
34
56
7
8
CONNECTOR
1
2
34
56
7
8
C
1
2
34
56
7
8
CO
1
2
34
56
7
8
CON
1
2
34
56
7
8
CONN
1
2
34
56
7
8
CONNE
1
2
34
56
7
8
CONNEC
1
2
34
56
7
8
CONNECT
1
2
34
56
7
8
CONNECTO
1
2
34
56
7
8
CONNECTOR ON
1
2
34
56
7
8
CONNECTOR O
1
2
34
56
7
8
CONNECTOR O N
L
OWER
1
2
34
56
7
8
CONNECTOR ON
L
1
2
34
56
7
8
CONNECTOR ON
LO
1
2
34
56
7
8
CONNECTOR ON
L
OW
1
2
34
56
7
8
CONNECTOR ON
L
OWE
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
1
2
34
56
7
8
CONNECTOR ON
L
OWER B
1
2
34
56
7
8
CONNECTOR ON
L
OWER BO
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOA
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOAR
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTOR
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
CO
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ON
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONN
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNE
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNEC
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECT
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTO
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTOR ON
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTOR O
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTOR ON
UPPER
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTOR ON
U
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTOR ON
UP
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTOR ON
UPP
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTOR ON
UPPE
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTOR ON
UPPER BOARD
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTOR ON
UPPER B
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTOR ON
UPPER BO
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTOR ON
UPPER BOA
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTOR ON
UPPER BOAR
1
2
34
56
7
8
CONNECTOR ON
L
OWER BOARD
C
ONNECTOR ON
UPPER BOARD
11 212312341234
5
1234
5
6
1234
5
6
7
1234
5
678
1234
5
6
7
8
11
2
1
2
3
1
2
34
1
2
345
1
2
3456
1
2
3456
71
2
3456
7
8
1
2
3456
7
8
C
ONNECTOR
1
2
3456
7
8
C
1
2
3456
7
8
CO
1
2
3456
7
8
C
ON
1
2
3456
7
8
C
ONN
1
2
3456
7
8
C
ONNE
1
2
3456
7
8
C
ONNEC
1
2
3456
7
8
C
ONNECT
1
2
3456
7
8
C
ONNECTO
1
2
3456
7
8
C
ONNECTOR ON
1
2
3456
7
8
C
ONNECTOR O
1
2
3456
7
8
C
ONNECTOR ON
LOWER
1
2
3456
7
8
C
ONNECTOR ON
L
1
2
3456
7
8
C
ONNECTOR ON
LO
1
2
3456
7
8
C
ONNECTOR ON
LOW
1
2
3456
7
8
C
ONNECTOR ON
LOWE
1
2
3456
7
8
C
ONNECTOR ON
LOWE R BOARD
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B O
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA R
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
C
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CO
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CON
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONN
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNE
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNEC
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECT
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTO
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR O
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR O N
U
PPER
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
U
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UP
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPP
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPPE
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPPER
BOARD
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPPE
RB
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPPE
RBO
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPPE
RBOA
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPPE
RBOAR
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPPE
RBOARD
11 212312341234
5
1234
5
6
1234
5
6
7
1234
5
6
7
8
1234
5
6
7
8
11
2
1
2
3
1
2
34
1
2
345
1
2
3456
1
2
3456
71
2
3456
7
8
1
2
3456
7
8
C
ONNECTOR
1
2
3456
7
8
C
1
2
3456
7
8
CO
1
2
3456
7
8
C
ON
1
2
3456
7
8
C
ONN
1
2
3456
7
8
C
ONNE
1
2
3456
7
8
C
ONNEC
1
2
3456
7
8
C
ONNECT
1
2
3456
7
8
C
ONNECTO
1
2
3456
7
8
C
ONNECTOR ON
1
2
3456
7
8
C
ONNECTOR O
1
2
3456
7
8
C
ONNECTOR ON
LOWER
1
2
3456
7
8
C
ONNECTOR ON
L
1
2
3456
7
8
C
ONNECTOR ON
LO
1
2
3456
7
8
C
ONNECTOR ON
LOW
1
2
3456
7
8
C
ONNECTOR ON
LOWE
1
2
3456
7
8
C
ONNECTOR ON
LOWE R BOARD
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B O
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA R
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
C
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CO
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CON
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONN
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNE
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNEC
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECT
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTO
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR O
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR O N
U
PPER
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
U
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UP
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPP
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPPE
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPPER
BOARD
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPPE
RB
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPPE
RBO
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPPE
RBOA
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPPE
RBOAR
1
2
3456
7
8
C
ONNECTOR ON
LOWE R B OA RD
CONNECTOR ON
UPPE
RBOARD
5
SP/ALSSPSP/SP/ASP/AL
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
M
ENUMMEMENMENU
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
RSTRRSRST
RST
P
RST
PA
RST
PAG
RST
PAGE
RST
PAGE
RST
PAGE 1
RST
PAGE 1
RST
PAGE 1 O
RST
PAGE 1 OF
RST
PAGE 1 OF
RST
PAGE 1 OF 1
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
HOME POSITION FUNCTION
Sequences the display
through SET POINT and
ALARM settings
Allows access to the menus
Displays full scale range of
unit
Clears or resets an Alarm
(alarm set for manual reset)
MAIN MENU FUNCTION
Return to home position
Return to home position
Sequences through
menus
Sequences through
menus
Enter into SUB MENU
SUB MENU FUNCTION
Return to home position
Return to previous
menu
Increments a value
Decrements a value
Changes a value or
setting. Press ENTER
and display will blink.
Adjust with UP or
DOWN arrows. Press
ENTER to store. Display
will stop blinking.
Peak/Valley SUB 
MENU resets display
to present value.
SP/AL
MENU
UP
ARROW
ENTER
RESET
KEY FUNCTIONS
SP1SSPSP1
S
P2
SP1
S
SP1
SP
SP1
SP2
A
LHI
SP1
SP2
A
SP1
SP2
AL
SP1
SP2
ALH
SP1
SP2
ALHI
ALLO
SP1
SP2
ALH
I
A
SP1
SP2
ALH
I
AL
SP1
SP2
ALH
I
ALL
SP1
SP2
ALH
I
ALLO
SCFMSSCSCFSCFM
99.99
SCFM
9
SCFM
99
SCFM
99.
SCFM
99.9
SCFM
99.99
X1K
S
P/ALSSPSP/SP/ASP/AL
R
ST
SP/AL
R
SP/AL
RS
SP/AL
RST
M
ENU
SP/AL
RS
T
M
SP/AL
RS
T
ME
SP/AL
RS
T
MEN
SP/AL
RS
T
MENU
E
SP/AL
RS
T
MENU
E
MULTIPLIERMMUMULMULTMULTIMULTI PMULTI P LMULT I P L IMULTI P L IEMULTI P L IE R DESCRIPTORMULTI P L IE R DMULTI P L IE R DEMULT I P LI E R D E SMULTI P L IE R DE S CMULT I P L IE R DE S C RMULTI P L IE R DE S C RIMULTI P L IE R DE S C RI PMULT I P LI E R D E S CR I P TMULTI P L IE R DE S C RI P TOMULTI P L IE R DE S C RI P TO R
VISIBLE
MULTIPLIER DESCRIPTOR
V
MULTIPLIER DESCRIPTOR
VI
MULTIPLIER DESCRIPTOR
VIS
MULTIPLIER DESCRIPTOR
VISI
MULTIPLIER DESCRIPTOR
VISIB
MULTIPLIER DESCRIPTOR
VISIBL
MULTIPLIER DESCRIPTOR
VISIBLE WITH
MULTIPLIER DESCRIPTOR
VISIBLE W
MULTIPLIER DESCRIPTOR
VISIBLE WI
MULTIPLIER DESCRIPTOR
VISIBLE WIT
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME
MULTIPLIER DESCRIPTOR
VISIBLE WITH S
MULTIPLIER DESCRIPTOR
VISIBLE WITH SO
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOM
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME V
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VE
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VEL
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELO
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOC
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCI
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCIT
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
A
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AN
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND F
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FL
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLO
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RANGES
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW R
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RA
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RAN
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RANG
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RANGE
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RANGES
FRONT
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RANGES
F
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RANGES
FR
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RANGES
FRO
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RANGES
FRON
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RANGES
FRONT PANEL
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RANGES
FRONT P
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RANGES
FRONT PA
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RANGES
FRONT PAN
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RANGES
FRONT PANE
MULTIPLIER DESCRIPTOR
VISIBLE WITH SOME VELOCITY
AND FLOW RANGES
FRONT PANEL
UNITSUUNUNIUNITUNITS
PROCESSPPRPROPROCPROCEPROCESPROCESS
VALUE
PROCESS
V
PROCESS
VA
PROCESS
VAL
PROCESS
VALU
PROCESS
VALUE
HIGHHHIHIGHIGH ALARMHIGHAHIGHALHIGHALAHIGHALARHIGHALARM
D
ESCRIPTOR
HIGH ALARM
D
HIGH ALARM
DE
HIGH ALARM
DES
HIGH ALARM
DESC
HIGH ALARM
DESCR
HIGH ALARM
DESCRI
HIGH ALARM
DESCRIP
HIGH ALARM
DESCRIPT
HIGH ALARM
DESCRIP
TO
HIGH ALARM
DESCRIP
TOR
LOW
HIGH ALARM
DESCRIP
TOR
L
HIGH ALARM
DESCRIP
TOR
LO
HIGH ALARM
DESCRIP
TOR
LOW ALARM
HIGH ALARM
DESCRIP
TOR
LOW A
HIGH ALARM
DESCRIP
TOR
LOW AL
HIGH ALARM
DESCRIP
TOR
LOW ALA
HIGH ALARM
DESCRIP
TOR
LOW ALAR
HIGH ALARM
DESCRIP
TOR
LOW ALARM
DESCRIPTOR
HIGH ALARM
DESCRIP
TOR
LOW ALARM
D
HIGH ALARM
DESCRIP
TOR
LOW ALARM
DE
HIGH ALARM
DESCRIP
TOR
LOW ALARM
DES
HIGH ALARM
DESCRIP
TOR
LOW ALARM
DESC
HIGH ALARM
DESCRIP
TOR
LOW ALARM
DESCR
HIGH ALARM
DESCRIP
TOR
LOW ALARM
DESCRI
HIGH ALARM
DESCRIP
TOR
LOW ALARM
DESCRIP
HIGH ALARM
DESCRIP
TOR
LOW ALARM
DESCRIPT
HIGH ALARM
DESCRIP
TOR
LOW ALARM
DESCRIPTO
HIGH ALARM
DESCRIP
TOR
LOW ALARM
DESCRIPTOR
SP1SSPSP1
DESCRIPTOR
SP1
D
SP1
DE
SP1
DES
SP1
DESC
SP1
DESCR
SP1
DESCRI
SP1
DESCRIP
SP1
DESCRIPT
SP1
DESCRIPTO
SP1
DESCRIPTOR
SP2
SP1
DESCRIPTOR
S
SP1
DESCRIPTOR
SP
SP1
DESCRIPTOR
SP2
DESCRIPTOR
SP1
DESCRIPTOR
SP2
D
SP1
DESCRIPTOR
SP2
DE
SP1
DESCRIPTOR
SP2
DES
SP1
DESCRIPTOR
SP2
DESC
SP1
DESCRIPTOR
SP2
DESCR
SP1
DESCRIPTOR
SP2
DESCRI
SP1
DESCRIPTOR
SP2
DESCRIP
SP1
DESCRIPTOR
SP2
DESCRIPT
SP1
DESCRIPTOR
SP2
DESCRIPTO
SP1
DESCRIPTOR
SP2
DESCRIPTOR
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
DOWN
ARR
OW
6
SETTING SET POINTS AND ALARMS
The hot key provides direct access to the Set Point and Alarm MENU. The Set Point and Alarm
MENUS that are displayed are based upon the Control (CtrL) SUB MENU.
SP/ALSSPSP/SP/ASP/AL SP/ALSSPSP/SP/ASP/AL
S
P/ALSSPSP/SP/ASP/AL
SP/ALSSPSP/SP/ASP/AL SP/ALSSPSP/SP/ASP/AL
SP/ALSSPSP/SP/ASP/AL
SP/ALSSPSP/SP/ASP/AL
S
P/ALSSPSP/SP/ASP/AL
SP/ALSSPSP/SP/ASP/AL SP/ALSSPSP/SP/ASP/AL
SP/ALSSPSP/SP/ASP/AL
S
P/ALSSPSP/SP/ASP/AL
SP/ALSSPSP/SP/ASP/AL
Visible whenVViVisVisiVisibVisiblVisibleVisible Visible wVisible whVisible wheVisible when
Visible when
Visible when
V
Visible when
Vi
Visible when
Vis
Visible when
Visi
Visible when
Visib
Visible when
Visibl
Visible when
Visible
Visible when
Visible
Visible when
Visible w
Visible when
Visible wh
Visible when
Visible whe
Visible when
Visible when
Visible when
Visible when
Visible when
V
Visible when
Visible when
Vi
Visible when
Visible when
Vis
Visible when
Visible when
Visi
Visible when
Visible when
Visib
Visible when
Visible when
Visibl
Visible when
Visible when
Visible
Visible when
Visible when
Visible
Visible when
Visible when
Visible w
Visible when
Visible when
Visible wh
Visible when
Visible when
Visible whe
Visible when
Visible when
Visible when
mode =
Visible when
Visible when
Visible when
m
Visible when
Visible when
Visible when
mo
Visible when
Visible when
Visible when
mod
Visible when
Visible when
Visible when
mode
Visible when
Visible when
Visible when
mode
Visible when
Visible when
Visible when
mode =
mode =
Visible when
Visible when
Visible when
mode =
m
Visible when
Visible when
Visible when
mode =
mo
Visible when
Visible when
Visible when
mode =
mod
Visible when
Visible when
Visible when
mode =
mode
Visible when
Visible when
Visible when
mode =
mode
Visible when
Visible when
Visible when
mode =
mode =
mode =
Visible when
Visible when
Visible when
mode =
mode =
m
Visible when
Visible when
Visible when
mode =
mode =
mo
Visible when
Visible when
Visible when
mode =
mode =
mod
Visible when
Visible when
Visible when
mode =
mode =
mode
Visible when
Visible when
Visible when
mode =
mode =
mode
Visible when
Visible when
Visible when
mode =
mode =
mode =
CONTROL MODECCOCONCONTCONTRCONTROCONTROLCONTROL CONTROL MCONTROL MOCONTROL MODCONTROL MODE
CONTROL MODE
CONTROL MODE
C
CONTROL MODE
CO
CONTROL MODE
CON
CONTROL MODE
CONT
CONTROL MODE
CONTR
CONTROL MODE
CONTRO
CONTROL MODE
CONTROL
CONTROL MODE
CONTROL
CONTROL MODE
CONTROL M
CONTROL MODE
CONTROL MO
CONTROL MODE
CONTROL MOD
CONTROL MODE
CONTROL MODE
CONTROL MODE
CONTROL MODE
CONTROL MODE
C
CONTROL MODE
CONTROL MODE
CO
CONTROL MODE
CONTROL MODE
CON
CONTROL MODE
CONTROL MODE
CONT
CONTROL MODE
CONTROL MODE
CONTR
CONTROL MODE
CONTROL MODE
CONTRO
CONTROL MODE
CONTROL MODE
CONTROL
CONTROL MODE
CONTROL MODE
CONTROL
CONTROL MODE
CONTROL MODE
CONTROL M
CONTROL MODE
CONTROL MODE
CONTROL MO
CONTROL MODE
CONTROL MODE
CONTROL MOD
CONTROL MODE
CONTROL MODE
CONTROL MODE
SET POINT ADJUSTMENT
Adjusting the Digihelic
®
II Controller Set Points is quick and simple. Instead of setting a set point and
deadband, simply adjust SP1H or SP2H for the desired relay turn on point, and then adjust SP1L or SP2L
for the desired relay turn off point.
PR
ES
SURE
PPRPREPRESPRESSPRESSUPRESSURPRESSURE
0
PRESSURE
0
0
PRESSURE
0
0
TIME
PRESSURE
0
0
T
PRESSURE
0
0
TI
PRESSURE
0
0
TIM
PRESSURE
0
0
TIME
0.2
PRESSURE
0
0
TIME
0
PRESSURE
0
0
TIME
0.
PRESSURE
0
0
TIME
0.2
0.4
PRESSURE
0
0
TIME
0.2
0
PRESSURE
0
0
TIME
0.2
0.
PRESSURE
0
0
TIME
0.2
0.4
0.6
PRESSURE
0
0
TIME
0.2
0.4
0
PRESSURE
0
0
TIME
0.2
0.4
0.
PRESSURE
0
0
TIME
0.2
0.4
0.6
0.8
PRESSURE
0
0
TIME
0.2
0.4
0.6
0
PRESSURE
0
0
TIME
0.2
0.4
0.6
0.
PRESSURE
0
0
TIME
0.2
0.4
0.6
0.8
1.0
(in. w.c.)
In the above graph, an instrument with a 1.0˝ range would have the SP1 relay turn on at 0.8˝ and off
at 0.4˝. SP1H sets the relay turn on point, and SP1L sets the relay turn off point. The relays outputs
normally function in the direct acting mode, which means the relays turn on with an increase in
pressure. SP1 may be configured to act as a reverse acting relay (refer to the 1SP SUB MENU setting,
page 15). When set for reverse acting, SP1H sets the relay turn OFF point, and SP1L sets the relay turn
ON point. SP2 is always direct acting.
SP/ALSSPSP/SP/ASP/AL
7
MENU MAPMMEMENMENUMENU MENU MMENU MAMENU MAP
CONTINUED
CCOCONCONTCONTICONTINCONTINUCONTINUECONTINUED
SETTINGSSSESETSETTSETTISETTINSETTINGSETTINGS
MAIN MENUS SUB MENUS
MENUS
UNAVAILABLE
FOR
BI-DIRECTIONAL
RANGES AND
RANGES ABOVE
25 IN. W.C.
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
EE
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
MENUMMEMENMENU
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
8
CONTINUEDCCOCONCONTCONTICONTINCONTINUCONTINUECONTINUED
SETTINGSSSESETSETTSETTISETTINSETTINGSETTINGS
MAIN MENUS SUB MENUS
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
EE
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
MENUMMEMENMENU
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
9
MAIN MENUS SUB MENUS
SETTINGS
Menus present only
in pressure operation
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
EE
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
MENUMMEMENMENU
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
10
Main Menu Selections (Upper Right Display Reads ME NU )
SECr Security - Lock out access to Set Point and Alarm settings, or lock out access to all
settings.
OPEr Operation - Selection of Pressure, Velocity or Flow and corresponding engineering units.
OUt Output - Select a Single Set Point, 2 Set Points, or a Set Point and an Alarm mode of
operation.
d.S Display - Monitor and adjust display related settings: Peak, Valley, display resolution, %
output and dampening.
AdU Advanced functions - Modify advanced function parameters, transmitter output scaling,
Modbus
®
communication settings, Maintenance Set Point settings and calibration.
11
MAIN MENUS and SUB MENUS
SECr (Security) MAIN MENU
SECr is the only SUB MENU in the security MENU. When the security SUB MENU is selected,
the present security level is displayed in the upper right hand display. To change the
security level, adjust the number displayed to the number shown in the following table for
the desired security level.
The password values shown in the table cannot be altered, so retain a
copy of these pages for future reference.
OPEr (Operation) MAIN MENU
The O PE r MENU selects the measurement type of the instrument.
The SUB MENUS are:
PrES - Pressure KFAC - K Factor XDIM - X Dimension
UEL - Velocity ArEA - Area YDIM - Y Dimension
FLO - Flow DIA - Diameter
If the instrument is set for Velocity, the OPEr MENU will have an additional K FAC SUB MENU. If the
instrument is set for Flow, the OPE r MENU will have additional KF AC and A rE A SUB MENUS. These
will be discussed under Velocity and Flow. When scrolling through the OPEr SUB MENUS, the
measurement type the unit is currently set for will show the units in the upper right display. The other
measurement types will have a blank upper right display.
Security Level Displayed
1
2
3
4
Access
All menus access
Menu Access
SP/AL Locked
SP/AL Access
Menus Locked
All settings locked
Password Value to Enter
10
70
90
111
Units visible, so unit
is presently set to
measure pressure
iisis is pis pris preis presis preseis presenis presentis presentlis presentlyis presently is presently sis presently seis presently setis presently set is presently set tis presently set tois presently set to
m
is presently set to
me
is presently set to
mea
is presently set to
meas
is presently set to
measu
is presently set to
measur
is presently set to
measure
is presently set to
measure
is presently set to
measure p
is presently set to
measure pr
is presently set to
measure pre
is presently set to
measure pres
is presently set to
measure press
is presently set to
measure pressu
is presently set to
measure pressur
is presently set to
measure pressure
Units not visible
is presently set to
measure pressure
U
is presently set to
measure pressure
Un
is presently set to
measure pressure
Uni
is presently set to
measure pressure
Unit
is presently set to
measure pressure
Units
is presently set to
measure pressure
Units
is presently set to
measure pressure
Units n
is presently set to
measure pressure
Units no
is presently set to
measure pressure
Units not
is presently set to
measure pressure
Units not
is presently set to
measure pressure
Units not v
is presently set to
measure pressure
Units not vi
is presently set to
measure pressure
Units not vis
is presently set to
measure pressure
Units not visi
is presently set to
measure pressure
Units not visib
is presently set to
measure pressure
Units not visibl
is presently set to
measure pressure
Units not visible Units not visible
is presently set to
measure pressure
Units not visible U
is presently set to
measure pressure
Units not visible Un
is presently set to
measure pressure
Units not visible Uni
is presently set to
measure pressure
Units not visible Unit
is presently set to
measure pressure
Units not visible Units
is presently set to
measure pressure
Units not visible Units
is presently set to
measure pressure
Units not visible Units n
is presently set to
measure pressure
Units not visible Units no
is presently set to
measure pressure
Units not visible Units not
is presently set to
measure pressure
Units not visible Units not
is presently set to
measure pressure
Units not visible Units not v
is presently set to
measure pressure
Units not visible Units not vi
is presently set to
measure pressure
Units not visible Units not vis
is presently set to
measure pressure
Units not visible Units not visi
is presently set to
measure pressure
Units not visible Units not visib
is presently set to
measure pressure
Units not visible Units not visibl
is presently set to
measure pressure
Units not visible Units not visible
12
PrES (Pressure) SUB MENU
For pressure measurement, the following units are available:
Table 1 Pressure Range vs. Available Units
INWC
.1000
.2500
.5000
1.000
2.500
5.000
10.00
25.00
50.00
100.0
FTWC
.2083
.4167
.8333
2.083
4.167
8.333
MMWC
2.540
6.350
12.70
25.40
63.50
127.0
254.0
635.0
1270
2540
CMWC
.2540
.6350
1.270
2.540
6.350
12.70
25.40
63.50
127.0
254.0
PSI
.1806
.3613
.9032
1.806
3.613
INHG
.1839
.3678
.7356
1.839
3.678
7.356
MMHG
.1868
.4671
.9342
1.868
4.671
9.342
18.68
46.71
93.42
186.8
MBAR
.2491
.6227
1.245
2.491
6.227
12.45
24.91
62.27
124.5
249.1
PA
24.91
62.27
124.5
249.1
622.7
1245
2491
6227
KPA
.1245
.2491
.6227
1.245
2.491
6.227
12.45
24.91
HPA
.2491
.6227
1.245
2.491
6.227
12.45
24.91
62.27
124.5
249.1
OZIN
.1445
.2890
.5780
1.445
2.890
5.780
14.45
28.90
57.80
UEL (Velocity) SUB MENU
For velocity measurement, the following units are available:
SFPM - Standard feet per minute
M/S - Meters per second
Table 2 Available Velocity Ranges
Note: Air velocity and flow readings are based upon standard dry air conditions with an ambient
temperature of 70°F and a barometric pressure of 29.92 INHG.
INPUT RANGE INWC
0 - 0.1
0 - 0.25
0 - 0.5
0 - 1
0 - 2.5
0 - 5
0 - 10
0 - 25
SFPM RANGE
0 - 1266
0 - 2002
0 - 2832
0 - 4004
0 - 6332
0 - 8954
0 - 12.66 x IK
0 - 20.02 x IK
M/S RANGE
0 - 6.431
0 - 10.17
0 - 14.39
0 - 20.35
0 - 32.17
0 - 45.48
0 - 64.33
0 - 101.7
INWC - Inches of water column
FTWC - Feet of water column
MMWC - Millimeters of water column
CMWC - Centimeters of water column
PSI - Pounds per square inch
INHG - Inches of mercury
MMHG - Millimeters of mercury
MBAR - Millibar
PA - Pascal
KPA - Kilopascals
HPA - Hectopascals
OZIN - Ounce inches
Note: O VF L(over flow) or UnFL(under flow) will appear when the ranges have been exceeded above
or below full scale by 2%.
13
FLO (Flow) SUB MENU
For flow measurements the following units are available:
SCFM - Standard cubic feet per minute
M^3H - Cubic meters per hour
FLO r (Flow Range) SUB MENU
LO - 99.99 x 1K flow range
HI - 999.9 x 1K flow range
Tables 3 -6 show the flow ranges available, and the maximum duct size that can be set for each input
range.
Table 3
FLOr = LO Maximum Duct Size (English)
RANGE
IN WC
0.1
0.25
0.5
1
2.5
5
10
25
SCFM
RANGE
99.99 x 1K
99.99 x 1K
99.99 x 1K
99.99 x 1K
99.99 x 1K
99.99 x 1K
99.99 x 1K
99.99 x 1K
MAX. DUCT
SIZE, SQ. FT.
78.9
49.9
35.3
24.9
15.7
11.1
7.8
4.9
KFAC
SUB MENU
KFAC
K Factor - becomes accessible if the instrument is set for Velocity or Flow.
When the Digihelic
®
II Controller is used with a pitot tube, the manufacturer may specific a K Factor.
The adjustment range is 0.01 to 2.00. The factory setting is 1.
Table 4
FLOr = HI Maximum Duct Size (English)
RANGE
IN WC
0.1
0.25
0.5
1
2.5
5
10
25
SCFM
RANGE
999.9 x 1K
999.9 x 1K
999.9 x 1K
999.9 x 1K
999.9 x 1K
999.9 x 1K
999.9 x 1K
999.9 x 1K
MAX. DUCT
SIZE, SQ. FT.
789.8
499.5
353.1
249.7
157.9
111.7
78.9
49.9
Table 5
FLOr = LO Maximum Duct Size (Metric)
RANGE
IN WC
0.1
0.25
0.5
1
2.5
5
10
25
Mˆ3/Hr
RANGE
99.99 x 1K
99.99 x 1K
99.99 x 1K
99.99 x 1K
99.99 x 1K
99.99 x 1K
99.99 x 1K
99.99 x 1K
MAX. DUCT
SIZE Mˆ2
4.32
2.73
1.93
1.37
0.86
0.61
0.43
0.27
Table 6
FLOr = HI Maximum Duct Size (Metric)
RANGE
IN WC
0.1
0.25
0.5
1
2.5
5
10
25
Mˆ3/Hr
Range
999.9 x 1K
999.9 x 1K
999.9 x 1K
999.9 x 1K
999.9 x 1K
999.9 x 1K
999.9 x 1K
999.9 x 1K
MAX. DUCT
SIZE, Mˆ2
43.19
27.31
19.3
13.64
8.63
6.10
4.31
2.73
14
ArEA, DI A, XDI M and YDIM SUB MENUS
These SUB MENUS become accessible if the instrument is set for flow. When measuring flow, the
area of the duct must be specified. Tables 3 and 4 show the input range vs maximum flow and duct
size. For a rectangular duct the maximum size is specified in square feet or meters. For a circular duct
the maximum size is specified as the diameter. X, Y and circular dimensions are entered in feet with
0.01 foot resolution for F LO r = L O and 0.1 foot resolution for F LO r = H I, or entered in millimeters with
1 millimeter resolution.
ArEA - Area, select CIR for a circular duct or RECT for a rectangular duct. If a circular duct
is selected, the DIA SUB MENU will be activated. If a rectangular duct is selected, the X DI M
and Y DI M SUB MENUS will be activated.
DIA - Diameter, enter the diameter of a duct
XDIM - Enter the “X” dimension of a duct
YDIM - Enter the “Y” dimension of a duct
OUt (Output) MAIN MENU
The O Ut MENU selects the output type of the instrument. The SUB
MENUS are:
CtrL- Control type ALrE - Alarm reset, manual or auto
ISP - SP1 reverse or direct acting AL.H - Alarm inhibit
AL - Alarm type ALDL - Alarm delay
Y
X
15
0
100
Process
Re
v
e
rse
Act
i
n
g
Tim
e
SPH
SPL
Relay Inactive
Relay Active
CtrL (Control) SUB MENU
1SP - Single set point
2SP - Two fully independent set points
SPAL - Single set point and alarm
1SP (SP1 Reverse or Direct Acting) SUB MENU
DIR - Direct. Relay turns on with increasing pressure
REV - Reverse. Relay turns on with decreasing pressure
0
100
Process
Di
r
e
c
t
Act
i
n
g
T
im
e
SPH
SPL
Relay Inactive
Relay Active
16
The following alarm function SUB MENUS are activated when
CtrL
is set to
SPAL
:
AL
(Alarm Type) SUB MENU
HI
- High alarm
LO
- Low alarm
HILO
- For a high/low guardband type alarm
ALARM ADJUSTMENT
Alarm settings are dependent upon the selected alarm mode. The Digihelic
®
II Controller alarm may
be configured as a High Alarm, Low Alarm, or High/Low Alarm. Alarm settings are all absolute and may
be set to anywhere within the range of the instrument. The dead bands of the alarms are fixed at 1%
of full scale.
MIN. PRESSURE
MAX. PRESSURE
ALHI
Relay OFF Relay ON
HIGH ALARM FUNCTION
MIN. PRESSURE
MAX. PRESSURE
ALLO
Relay ON Relay OFF
LOW ALARM FUNCTION
MIN. PRESSURE
MAX. PRESSURE
ALLO
Relay ON Relay OFF Relay ON
HIGH/LOW ALARM
FUNCTION
ALHI
17
ALrE (Alarm Reset) SUB MENU
ONOF- Automatic reset
HOLD - Manual reset. An alarm is reset by the RESET key on the front panel, or an external
reset switch.
AL.H (Low Alarm Inhibit) SUB MENU
ON - Alarm inhibit is on
OFF - Alarm inhibit is off
If A L. H is selected ON, a low alarm condition is suspended upon power up until the process
value passes through the alarm set point once.
ALDL (Alarm Delay) SUB MENU
Sets the amount of time an alarm condition must be continuously met before the alarm
condition is recognized. The alarm delay is adjustable from 0-3600 seconds.
d.S (Display) MAIN MENU
PEAK - Peak value rESO - Resolution
VALy - Valley value Pd.S - Process display
ZERO - Zero DAMP - Dampening level
PEAK (Peak) SUB MENU
The Peak feature stores the highest pressure reading the instrument has measured since the
last reset or power up. At power up PEAK is reset to the present pressure reading. To manually
reset the PE AK value, press the RESET key while in the PE AK SUB MENU.
VALy (Valley) SUB MENU
The valley feature stores the lowest pressure reading the instrument has measured since the
last reset or power up. At power up VALy is reset to the present pressure reading. To
manually reset the VAL y value, press the RESET key while in the VALy SUB MENU.
18
rESO (Resolution) SUB MENU
The Digihelic
®
II Controller is capable of displaying four digits of resolution. However, at very low
pressures the instability of the pressure may cause fluctuations in the least significant digit
causing the least significant digit to be of little value.
Three digit resolution (3DIG ) can only be active when there is at least one digit to the right of a
decimal.
3DIG - Set display for 3 digit resolution
4DIG - Set display for 4 digit resolution
Pd.S (Process Display) SUB MENU
STD - Display reads pressure, velocity, or flow values
PCT - Display reads % of full scale value
When the display is reading percent, PCT is displayed in the upper right of the display. The
percent display is only available in pressure operation.
DAMP (Dampening) SUB MENU
Adjust from 1-16
Dampening stabilizes the display from instabilities due to things such as vibration and
excessive pressure fluctuations. The dampening setting adjusts the amount of readings that
are averaged for each display update. Adjust the dampening value until the display reads a
stable value for the application.
AdU (Advanced) MAIN MENU
POL - Process output low ADDR - Modbus
®
address
POH - Process output high WR - Modbus
®
write enable/disable
MSP1 - Maintenance set point 1 ZERO - Zero calibration
MSP2 - Maintenance set point 2 SPAN - Span calibration
POL and POH (Process Output Low and High) SUB MENUS
This feature is used in pressure operation only.
Process output low and high are used to scale the 4-20 mA output. Set POL to the desired
display reading for 4mA output, and set POH to the desired display reading for 20 mA output.
POH must be higher than P OL . POL may be adjusted 2% BELOW minimum scale up to POH.
POH may be adjusted from P OL to 2% ABOVE maximum scale.
MSP1 and MSP 2 (Maintenance Set Point 1 & 2) SUB MENUS
Adjust for the desired maintenance set points when the unit is placed in the maintenance
mode. The deadband is fixed at 2% of full scale. To enter or leave the maintenance mode,
press and hold the for 8 seconds.
ADDR (Modbus
®
Address ) SUB MENU
Modbus
®
communication instrument address. Set from 1 to 247. This number must match the
address number used by the host computer.
To obtain the Digihelic
®
II Controller Modbus
®
register list please visit www.dwyer-inst.com
See page 4 for wiring diagram.
WR (Modbus
®
Write Protect) SUB MENU
d.S - Disables write commands from Modbus
®
. Modbus
®
can only read information from the
instrument.
En - Enable write commands from Modbus
®
. Modbus
®
can read information from and write
information to the instrument.
ZERO and SPA N (Calibration of Zero and Span) SUB MENUS
The lower display reads CAL in this mode.
ZERO Calibration
Note: For accurate calibration, DO NOT apply any pressure when performing this function.
With the display reading ZERO, press the ENTER key. The upper display will blink. Press
ENTER again to complete the zeroing of the instrument or press the M ENU key to cancel.
SPAN Calibration
With the display set to SPAN, apply full scale pressure to the unit. Press the ENTER key. The
upper display will blink. Press ENTER again to complete the calibration or press the M EN U key
to cancel.
SP/ALSSPSP/SP/ASP/AL
RST
PAGE 1 OF 12
8
RST
PAGE 1 OF 12
8/
RST
PAGE 1 OF 12
8/2
RST
PAGE 1 OF 12
8/25
RST
PAGE 1 OF 12
8/25/
RST
PAGE 1 OF 12
8/25/0
RST
PAGE 1 OF 12
8/25/03
©Copyright 2017 Dwyer Instruments, Inc.
Printed in U.S.A. 6/17
FR# 443434-00 Rev. 4
DWYER INSTRUMENTS, INC.
Phone: 219/879-8000 www.dwyer-inst.com
P.O. BOX 373 • MICHIGAN CITY, IN 46360, U.S.A. Fax: 219/872-9057 e-mail: [email protected]
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Dwyer Series DHII User manual

Dwyer
Brand
Dwyer
Model
Series DHII
Category
Measuring, testing & control
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents